Source Technologies Secure Micr Printer St9612 Users Manual

STI MICR ST9620 st9612-user-guide

ST9612 to the manual 219b050f-7328-46f4-a18b-ebdd0261a79e

2015-02-06

: Source-Technologies Source-Technologies-Secure-Micr-Printer-St9612-Users-Manual-527971 source-technologies-secure-micr-printer-st9612-users-manual-527971 source-technologies pdf

Open the PDF directly: View PDF .
Page Count: 47

Secure MICR Printer

User’s Guide

Released Electronic Copy

ST Doc Control

07/02/2009

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

No part of this document may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying, recording, or by any information

storage and retrieval system, without permission in writing from Source Technologies,

LLC.

Published in the United States of America by:

Source Technologies, LLC

2910 Whitehall Park Drive

Charlotte, NC 28273

Author: Source Technologies, LLC

Notice

This manual serves as a reference for a Source Technologies Secure MICR Printer.

This manual should be used as a reference for learning more about MICR technology

and developing MICR printing applications. This guide was produced to assist IS

Technicians and Engineers in the integration of Source Technologies’ programmed

printers with their custom MICR applications. The guide also contains information on

MICR related error messages that post to the operator panel.

To the best of our knowledge, the information in this publication is accurate: however,

neither Source Technologies, LLC, its dealers or affiliates assume any responsibility or

liability for the accuracy or completeness of, or consequences arising from, such

information. Changes, typos, and technical inaccuracies will be corrected in subsequent

publications. This publication is subject to change without notice. The information and

descriptions contained in this manual cannot be copied, disseminated, or distributed

without the express written consent of Source Technologies, LLC. This document is

intended for informational purposes only. Mention of trade names or commercial

products does not constitute endorsement or recommendation for use by Source

Technologies, LLC. Final determination of the suitability of any information or product for

use contemplated by any user, and the manner of that use is the sole responsibility of

the user. We recommend that anyone intending to rely on any recommendation of

materials or procedures mentioned in this publication should satisfy himself as to such

suitability, and that he can meet all applicable safety and health standards.

All trade names or products used in this manual are for identification purposes only and

may be trademarks or registered trademarks of their respective companies.

Document Number: 104048

Revision: A

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

iii

Table of Contents

1. Printer and Driver Installation.......................................................................1

Driver Overview.................................................................................................2

Downloading the Universal Driver .....................................................................3

Unzipping the Driver..........................................................................................3

Installing the Driver............................................................................................4

Configure the Driver to enable MICR Mode ....................................................10

Configure the Driver to Recognize the Printer Secure Fonts...........................11

Configure another driver to print without MICR toner ......................................11

Selecting the Printer........................................................................................14

2. MICR Overview.............................................................................................16

The Check Clearing System............................................................................16

MICR Printing Standards in the United States Today......................................16

3. MICR Check Design .....................................................................................18

General Features of Check Design .................................................................18

Position and Dimension Gauge.......................................................................18

Design Elements in Detail ...............................................................................18

Data Elements.................................................................................................19

4. Quality Issues...............................................................................................23

Printer Features ..............................................................................................23

MICR Toner.....................................................................................................23

MICR Check Stock..........................................................................................24

5. Security Issues.............................................................................................25

6. MICR Features..............................................................................................27

Secure MICR...................................................................................................27

MICR Fonts .....................................................................................................27

Secure Fonts...................................................................................................27

MicroPrint ........................................................................................................28

Resource Storage ...........................................................................................28

MICR Toner Cartridge.....................................................................................28

7. MICR Commands .........................................................................................29

Table of Contents

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

PJL MICRJOB.................................................................................................29

Fonts and Secured Resources........................................................................29

PJL Unlock Sequence.....................................................................................30

PJL Re-Lock Sequence...................................................................................30

PJL Re-Lock Sequence With A New Password Value ....................................30

PCL Font Call Commands...............................................................................30

PJL INFO MICR COMMAND ..........................................................................32

Error Messages...............................................................................................34

Toner Cartridge and Photoconductor Units.....................................................34

Toner Cartridge and Photoconductor Units.....................................................35

Toner Low .......................................................................................................35

Toner Out ........................................................................................................36

Photoconductor Unit Life Warning...................................................................36

Replace Photoconductor (printer hard stop)....................................................37

Load MICR Toner............................................................................................37

8. MICR Command Example ...........................................................................38

PJL Unlock Sequence.....................................................................................38

PCL Initial Set-Up............................................................................................38

PCL MACRO Call............................................................................................38

PCL Font Calls, Positioning Commands and Variable Print Data ...................38

PJL Re-Lock Sequence...................................................................................39

Appendix A: E13B MICR Font Mapping .........................................................41

Appendix C: ICR Secure Numeric Font Mapping ..........................................44

Appendix D: CMC7 MICR Font Mapping ........................................................45

Appendix E: Contact.........................................................................................47

Appendix F: Photoconductor Replacement ...................................................48

NOTE: To maintain a high resolution, Source Technologies recommends printing

all documents in color.

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

1. Printer and Driver Installation

Note: To access Source Technologies’ secure fonts loaded on the printer, such as

the E13B MICR font, download the universal driver as described in the next

section. The printer drivers on this CD may be used for general office printing but

do not facilitate using secure fonts.

For complete information on how to unpack and setup your printer, see your printer’s

user’s guide.

1. Locate the CD that was shipped with your printer and load into CD drive. The

CD should auto-run and the following screen will be displayed. If auto-run is

disabled on your computer, browse to the CD and click Setup.exe to run

2. Click on View User’s Guide for information on unpacking, installing, and

operating your printer.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Driver Overview

Your new MICR printer requires specific PCL 5 commands to load and print secure fonts

such as the MICR E13B font. These specific commands may be coded in to your

custom application, or if you use a software program such as Source Technologies’

CheckPartner™ Enterprise, these commands are automatically sent to the printer as

needed. To print checks or other documents requiring secure fonts from other Windows

applications please download the universal driver— designed specifically to allow

access to your printer’s secured resources—using the following steps:

1. Select the Driver Zip file matching your operating system and printer model.

2. Download this file to a location, such as the Windows Desktop.

3. Unzip this file and make sure the “Use Saved path” option is selected.

4. Browse to the Source Tech Driver folder extracted from the zip file.

5. Run the driver install program. For example:

Printer_UDO_2KXP03_x86_PCL_Emul_sys_en.exe

6. Follow the instructions to install the driver.

7. Configure the driver to use MICR_on.sep page separator file (used to select

MICR mode).

8. Configure the driver to “Update the Font list” using the 96XXfont.pcm file. This

will enable Windows applications to recognize the printer’s secure fonts.

9. From the Windows application, select the installed printer.

10. From a Windows application, select the specific text to be printed. Then select

the secure font name and point size using the capabilities of the particular

Windows application.

The following fonts and point size are supported.

Font Name Point Size Font Sample

MICR E13B 8

MICR CMC7 8

SECURE 36

ICR Secure 12

MicroPrint 1

Note: The fonts illustrated above may not match the size or appearance of those

printed by the MICR printer. The characters are enhanced for illustration purposes

only.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Downloading the Universal Driver

1. Browse to the URL below from your web browser.

http://www.sourcetech.com/support/drivers.asp

2. From this page go to the section for the particular operating system you are

using such as Widows 2000, XP, etc.

3. Click on your specific model such ST9612, ST9620 etc.

4. When the File Security dialog box appears, select Save.

5. When the Save As file dialog box appears browse to a folder you have

created or to the Desktop and save the driver zip file.

6. Once the file is downloaded browse to the folder where saved and double-

click the zip file to extract the driver contents. For example, the zip file for

Windows 2000, XP, and Windows Server 2003 is:

Universal_Driver_2KXP03_x86.zip

Note: The remainder of the instructions applies to Windows XP. The exact steps

may vary depending on the particular operating system you are using.

Unzipping the Driver

1. Double-click the driver zip file to launch the unzip program installed on your

computer.

2. Follow the steps for your particular unzip program to extract the files. Make

sure the “Save with Paths” option is selected.

3. Browse to the location where you wish to extract the files, such as the

Desktop, and then extract the files.

4. The extracted zip files will be saved to the location selected in the previous

step. For example, if you saved the file to the Desktop you should now find a

new folder on the Desktop named:

Source Tech Driver

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Installing the Driver

Note: Do not connect the printer at this time.

1. From the Source Tech Driver folder, double-click the driver installation

program.

Note: The name of the driver’s .exe program will vary depending on the

operating system being used. There will only be one executable file

included with the driver.

2. Click Next >.

3. Click I accept the terms, and then click Next >.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

4. Leave the “Save files in folder” option as shown above then click Next >.

5. After the installation program installs the necessary files, the following

message will be displayed revealing the next steps required to install the

driver. At the same time, an “Add Printer Wizard” will run as shown in the next

step.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

6. Click Cancel if connecting through USB.

7. Power on the printer and wait for the New Hardware Wizard to appear.

8. Select “No, not this time,” then Next >.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

9. Select Install from a list or specific location (Advanced).

10. Click Next >.

11. Click Don’t search, I will choose the driver to install.

12. Click Next >.

13. Scroll down the list and select Printers.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

14. Click Next >.

15. Click Have Disk.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

16. Select Browse. Browse

to the driver files on your

disk and then select

Open.

17. Select OK.

18. Select Source

Technologies

from the

Manufacturer list

and then click

Next >.

19. Select Yes to continue.

20. Once the files have copied, select Finish to close the Wizard.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Configure the Driver to enable MICR Mode

To unlock the secure font resources located in the printer, the driver must be configured

to send down a separator page before each print job. The separator page contains the

necessary commands to unlock the resources.

1. Click Start then select the Printer and Faxes folder.

2. Locate the printer you just installed and right-click the icon. Then select

Properties.

3. From the General tab, type a descriptive name for the printer, such as

ST9620 MICR.

4. Click the Advanced tab.

5. Click the Separator Page button. Then select Browse and locate the

MICR_on.sep file in the Windows\system32 folder.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Configure the Driver to Recognize the Printer Secure Fonts

1. Select the Fonts tab. Select Update List.

2. Select the upper Browse button.

Locate the directory that contains

the 96XXfont.pcm file and select

OK.

3. Select the Search Path button.

4. Select ST 96XX Font Collection.

Then select the Add to driver

button.

5. Select the Done.

6. When you have made all of the

desired changes choose OK to

save your settings.

Configure another driver to print without MICR toner

If you plan to use your printer for normal office printing (without MICR toner or fonts) you

must add a second instance of the printer driver. Switching between MICR and non-

MICR modes alters settings which are stored in the printer’s NVRAM. It is

recommended not to switch between the modes more than a few times per day to avoid

wearing out the NVRAM part.

1. In the Printers folder, select Add a Printer.

2. Select the Local printer

option, then select Next >.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

3. Choose the port to which your MICR printer is connected and then select

Next >.

4. Select the Have Disk button and the Browse button and locate the driver

files. Select Source Technologies as the Manufacturer and select Next >.

5. Choose Keep existing driver and select Next >.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

6. Enter a Printer name

to differentiate it from

the MICR instance of

the driver and then

decide if it is to be the

default printer. Select

Next >.

7. If you do not wish to share your printer on a network, leave the "Do Not share

this printer" button marked and choose "Next". Otherwise, select the "Share

as" radio button and enter the name you wish to assign to this shared printer.

Then choose Next >. If you wish, you may enter the location of this printer

and/or any comments to associate with the printer and choose Next >.

8. You now have the option to print a test page to test the configuration of your

printer. Click Next >.

9. Select Finish to complete the installation.

10. You can now setup your printer by browsing to the Printers folder and right-

clicking on your printer's icon. From the menu, click Properties.

□ Select the Advanced tab.

□ Select the Separator Page button.

□ Select Browse and locate the MICR_off.sep file.

11. When you have made all of the desired changes choose OK to save your

settings.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Selecting the Printer

Printing Secure font resources from a Windows Application

First, set the MICR printer as the active printer – in most applications this is done by

selecting Print from the File menu. This is not necessary if the MICR printer is the default

printer.

Source Technologies’ fonts should appear in the application’s font formatting options.

The fonts are named:

ICR Secure 12 pt.

MICR CMC7 8 pt.

MicroPrint 1 pt.

MICR E13B 8 pt.

SECURE 36 pt.

They will usually appear in alphabetical order among all other available fonts.

The font size must be selected as indicated in the font name. The font displayed on the

screen will not resemble the printed font.

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Comparison of printer drivers configured as MICR and non-MICR

CONFIGURED FOR MICR CONFIGURED FOR NON-MICR

MICR_on.sep separator page used

Unlocks Secure Resources (fonts)

Copy Count = 1

Jam Recovery = Off

MICR Toner ONly

DEFAULT MICRJOB=ON

MICR_off.sep separator page used

Locks Secure Resources (fonts)

DEFAULT MICRJOB=OFF

Secure Fonts enabled by 96xxFont.pcm

ICR Secure 12 pt.

MICR CMC7 8 pt.

MICR E13B 8 pt.

MicroPrint 1 pt.

SECURE 36 pt.

No Secure Fonts

Universal Driver Options to set on the driver Install Options tab

Base printer

Automatic duplex

Multipurpose feeder

Flash memory card (optional, if installed)

Tray 2 (optional)

Printer and Driver Installation | 1

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

2. MICR Overview

MICR stands for Magnetic Ink Character Recognition. All MICR documents have a MICR

line with numbers and symbols printed in a unique MICR font with magnetically

chargeable ink or toner. Each character of the MICR font has a unique waveform when

sensed magnetically. Financial institutions and the Federal Reserve use the MICR line to

identify and sort checks. The high-speed automated processing of checks and other

financial documents depends on the accuracy and the integrity of the data printed in the

MICR line. Your new Source Technologies Secure MICR Printer is specifically designed

to produce high quality MICR documents.

The Check Clearing System

The Check Clearing for the 21st Century Act (Check 21) was signed into law October 28,

2003. Prior to Check 21, checks traveled through the bank’s high speed reader/sorter

equipment an average of near seven times in the Check Clearing process. Some checks

could be read up to 30 times or more by these machines.

In today’s environment high and low speed check readers can capture a picture or

image of the check allowing for images to be exchanged between financial institutions,

the Federal Reserve, and other clearing houses. This new law, Check 21, defines what

is called a “Substitute Check”, and removed barriers that existed in converting physical

checks to check images for clearing. The original physical check can now be truncated

by the first institution that converts the check to image. The original check can now be

destroyed.

United States and International MICR Standards still require the printed MICR line

information to be of the highest quality and durability. Additionally, issues related to

check fraud continue to place high importance on print quality. For these reasons, the

quality and durability of information printed with Source Technologies Secure MICR

Printers remains a key new product development criterion.

MICR Printing Standards in the United States Today

Congress established the Federal Reserve System (FRS) in 1913. Today most

commercial banks in the United States belong to the FRS. Many other depository

institutions provide banking and checking account services to the public. These other

institutions, such as some credit unions, savings and loan associations and non-member

banks, are not formally part of the FRS. However, they have access to the payment

services it provides and are subject to many of the FRS regulations.

In 1958, because of the explosive growth of check usage, the American Bankers

Association selected the E-13B MICR font and the MICR system as the technology for

high-speed check processing. Today, check standards are determined by the Accredited

Standards Committee X9AB Payments Subcommittee of which Source Technologies is

a voting member. The latest versions of the standards and technical guidelines are

available from:

MICR Overview | 2

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Hardcopy: Softcopy:

Global Engineering Documents X9 Electronic Bookstore

Phone 800-854-7179 or 303-397-7956 www.X9.org - click ESS

Fax 303-397-2740 www.ansi.org - click ESS

global@ihs.com or

http://global.ihs.com http://webstore.ansi.org

The key standards that address check documents are as follows:

ANS X9.7 Specifications for Bank Check Background and Convenience Amount Field

ANS X9.100-160 Specifications for Placement and Location of MICR Printing

ANS X9.100-10 Paper Specifications for Checks

ANS X9.100-20 Print and Test Specifications for Magnetic Ink Character Recognition

(MICR)

For those with an interest or need there are also US standards that address Deposit

Tickets, Check Endorsements (the back of the check), image interchange file formats,

and other MICR areas.

Users of our Secure MICR Printers are not required to have access to the above

standards. Our Technical Support staff maintains current knowledge of the standards

and changes that affect the check industry in the US and other countries with unique

requirements.

MICR Overview | 2

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

3. MICR Check Design

General Features of Check Design

To be a legal and negotiable document, the necessary data elements required on a

check are the date, amount, payee name, payer’s bank name, and payer’s signature.

Other elements included in a good check design are: the amount in words, account title,

check serial number, fractional routing number and MICR line.

A good check design contains security features and is formatted to be easily read by

both machines and the human eye. If the format is complicated, the depositor, bank

employee or reader/sorter machine may make an error in reading the data.

Position and Dimension Gauge

A MICR position and dimension gauge, like the one available from Source Technologies

(part number 205-1000MGE or 220-M1027-34, is an important tool for use in designing

checks. During check design, check your output against this gauge to determine if the

data elements (date, amount, payee name, payer’s bank name, and payer’s signature)

are correctly positioned on your document.

Design Elements in Detail

Paper

The ideal paper for check production is 24 to 28 lb. laser bond. Source

Technologies’ MICR lab has tested paper stock from most major manufacturers

and has compiled a list of products that produce superior results. Contact your

sales representative for this information. For a fee, Source Technologies will test

your paper for proper MICR adherence and check reader/sorter performance.

There are also many security features available to aid in the overall security of

your MICR documents. Please refer to Chapter 5, Security Issues, for more

information on check stock specifications and security features.

Size

The size of check documents must be:

6.00 inches to 8.75 inches in length

2.75 inches to 3.66 inches in height

We recommend standard 8.5" X 11" letter size stock or 8.5" X 14" legal size

stock for proper feeding through your ST Secure MICR Printer. The number of

checks per page is determined by your application. Custom size stock other than

letter or legal can be done with proper planning and application programming

within the paper size specifications for the base printer.

MICR Clear Band

The MICR clear band is an area at the bottom of the check where the MICR line

prints. No other magnetic printing should appear in this area on both the front

and back of the document. The clear band is an area 0.625 (5/8) inches high

from the bottom of the check running the entire length of the check. Exact MICR

line placement in this area is very important. Please refer to Figure 3.1 for more

information on MICR line placement.

MICR Check Design | 3

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Data Elements

Date

The date is a required data element for a check. It represents the day upon which

or after which the transfer of the check amount may take place. The date is

usually placed in the upper right portion of the check so it does not interfere with

the convenience amount field. The common format is Month, Day and Year,

however, the military format of Day, Month and Year is also acceptable.

Amount

The amount of the check is a required data element for negotiation. The amount

usually appears at least twice on the check. The amount printed in numbers is

called the convenience amount. The amount printed in words is sometimes

referred to as the legal amount; this is the amount that applies if there is a

difference between the two amount fields. The amount may also be printed a

third time on the check in a secure font, intended to make alteration of the

amount field difficult. Please refer to Chapter 6 and Appendix B for information on

Source Technologies’ Secure Numeric Font.

Convenience Amount

The convenience amount location is specified in ANSI X9.7. The basic location

is illustrated in Figure 3.1. Since this amount can be machine scanned, its

location and design should be kept within the specifications. The amount

beginning with the dollar sign should be left justified within the scan area with

numbers spaced normally to the right. The dollars and cents should be

separated by a decimal point with the cents printed in the same size font as the

rest of the field. Embedded commas should not be used. The convenience

amount background should have good reflectance so it does not interfere with

optical scanning (see ANSI X9.7).

The convenience amount should be printed in a simple, fixed pitch font. We

recommend our ICR Secure Numeric Font (see Appendix C). It was designed to

be easily read by image capture equipment and is also a fraud deterrent. A fixed

pitch courier font, or if available, OCR-B, are also acceptable fonts to print the

convenience amount.

Note: The Source Technologies’ Secure Numeric Font (see Appendix B)

should not be used in the convenience amount since it is not a machine

readable font.

Amount in Words

The amount in words (sometimes called the legal amount) is normally located

either above or below and to the left of the convenience amount. The area for

the amount in words should be entirely filled to make alterations difficult. The

amount should start at the far left of the line with the words placed immediately

adjacent to each other. The cents need not be written out. They may be

expressed as a fraction (60/100), and should be placed immediately to the right

of the dollar amount and followed by a line or other space filler to inhibit

alteration.

Example: One hundred forty-four and 62/100---------------DOLLARS

MICR Check Design | 3

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Given the available area on the document, you may need to use a smaller font

when printing larger value amounts.

Payee Area

The payee is a necessary data element for a negotiable document. The payee

area is generally to the left side of the document either above or below the

amount in words. It is often preceded by the words “Pay to the Order Of.” The

payee data should not enter the MICR clear band which extends 5/8 of an inch

above the bottom of the check. Some financial institutions have established

specific print requirements for the Payee Name and optional address. Consult

your bank for details on their print requirements.

Signature Area

A signature is a required data element for a negotiable document. The signature

or signatures authorize the bank to honor the check; therefore, it must match the

bank’s records. The signature area should be beneath the convenience amount

area but the signatures should not enter the convenience amount area nor the

MICR clear band. This is especially true if you print the signature with MICR

toner.

Drawee Institution Name

The name of the institution where the maker’s account is located is referred to as

the drawee institution. The bank’s name, city, and state are required.

Account Title

The account title is normally printed in the upper left corner of the check. It

includes the name of the account holder and other information such as

addresses, telephone numbers, and logos. The data in the title should be legible

and sufficiently complete so that if the MICR data account number is destroyed,

the drawee institution can refer to the account title in order to trace the account

number.

Memo Line

This line is located in the lower left quadrant of the check, and is not required.

Data printed here does not contain any legal significance. Printing in this area

with magnetic toner should not extend downward into the MICR clear band which

is 5/8 of an inch above the bottom of the check.

Check Serial Number

The check serial number is generally printed in the upper right quadrant of the

check. Although the check number is not required for the check to be negotiable,

the account holder and financial institution use these numbers to reconcile

statements and execute stop payments. The check serial number should also

appear a second time in the MICR line, and these numbers should match. The

number of digits in the check serial number is controlled by the financial

institution and the MICR line format. Consult your banking institution for their

requirements.

Fractional Routing Number

The fractional routing number should be printed in a fractional format in the upper

right quadrant of the check. This number is assigned to identify the Federal

MICR Check Design | 3

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Reserve District and drawee institution. Consult with your bank for the proper

routing number and format for each of your accounts.

MICR Line

Accurate high-speed processing of your checks by financial institutions is

enabled by the accuracy and integrity of the data in the MICR line. Refer to

figure 3.1 for the location of the following MICR line fields. The MICR line is read

from right-to-left with position one being the right most position proceeding to

position sixty-five on the left. The MICR line must be printed at exactly eight

characters per inch.

Auxiliary On-Us Field—Positions 65 to 45

This field usually contains the check serial number for commercial size checks

and possibly account control information. It is bounded by On-Us symbols.

(). It is not included on personal, small size checks.

External Processing Code (EPC) Field—Position 44

This one digit field is position 44 of the MICR line. This field is usually left

blank. The use of this field is reserved and is controlled by the ASC X9AB

Standards Committee.

Routing Field—Positions 43 to 33

The routing field is bounded by Transit symbols in positions 43 and 33. It

contains fixed format information about the drawee institution. Consult with

your bank for the specific data field to be placed here for each of your

accounts.

On-Us Field—Positions 32 to 14

The On-Us field contains the makers’ account number. The structure and

content of this field is left to the drawee bank. On personal checks this field

also contains the check serial numbers. The On-Us field may not consist of

more than 19 characters. An On-Us symbol must appear immediately to

the right of the account number.

Blank Field—Position 13

Position 13 is always left blank.

Amount Field—Positions 1 to 12

The amount field is the right most field in the MICR line. It remains blank until

it is printed by the bank of first deposit. When the check enters the banking

system, the bank of first deposit encodes this field from data in the

convenience amount field. It will be bounded by Amount symbols .

MICR Check Design | 3

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Figure 3.1: Sample Check

A. Serial Number: Must be in the upper right corner and match the serial number in the

MICR line (see D for further explanation).

B. Fractional Routing Transit Number: Should be in the upper right corner and must

match the routing transit number in the MICR line with the exception of the state

prefix number (ex. 66 = NC, 67 = SC, 64 = GA, etc.) and the preceding zeros.

C. Bank Name, State, City: The bank logo is optional. Name of bank, city and state

where the account will be assigned/opened are required fields.

D. Aux On-Us (46-55): This is a required field if the customer desires services offered

by the bank which require a serial number. The serial number format is controlled by

the payer’s bank. A & D should match.

E. Routing Number (34-42): Designates the Federal Reserve district and financial

institution. Each city, state or region that the bank serves has a unique institution

identifier. IMPORTANT: positions 35-42 are the Routing Numbers; position 34 is the

check digit.

F. Account Number: This is a unique number assigned to the customer’s account.

G. Optional Serial Number: Used for personal accounts (checks only). This should be

a 4-digit, zero-filled field that matches the serial number in the upper right corner.

H. Convenience Amount Area: should be in the general location shown above in the

diagram. The illustrated box in the diagram is optional and if used, should conform

to ANS X9.7. A single stroke dollar sign is required.

MICR Check Design | 3

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

4. Quality Issues

A high quality MICR document can be read by bank reader/sorter equipment many times

with no readability issues and does not result in damage to bank equipment. This quality

is the result of a well designed printer, an originally manufactured MICR toner cartridge

and high quality check stock.

Printer Features

Your Secure MICR Printer is equipped with some features to ensure high quality MICR

documents.

Paper Type

When the printer senses the presence of the ST MICR cartridge, internal

operating points that affect the print engine and fuse grade are optimized for

MICR documents and Source Technologies’ MICR toner. Paper type settings, if

selected through a printer driver (ex. Transparency) do not affect operating points

so that the printer remains optimized for MICR printing.

Print Density

When the printer senses the presence of the ST MICR cartridge, the internal print

density is controlled for MICR printing. Darker density settings of 9 and 10 do

print darker, but settings below the default value of 8 do not change print density.

MICR Toner Low

When MICR toner is low, the printer stops and the user is prompted. We

recommend shaking the cartridge to prolong its life. When low toner is sensed,

there is enough toner left to print additional quality MICR documents. Low toner

occurs at approximately the 90% point of cartridge life.

MICR Toner Empty

When the toner in the cartridge is determined to be too low to continue, the

printer stops. To continue printing, a new cartridge will need to be installed.

MICR Toner

Use only Source Technologies’ MICR toner when printing MICR documents. It is

specifically engineered to print quality MICR documents with your printer. The printer’s

MICR toner sensor is designed to work with the Source Technologies’ MICR toner

cartridge to prevent printing checks with regular toner present. Your Source

Technologies MICR printer can be used for general office printing. If a MICR print job

begins and the printer has a regular toner cartridge present, the printer will stop and

prompt the operator to install a MICR toner cartridge.

Source Technologies does not recommend the use of refilled MICR toner cartridges.

Refilled cartridges may result in expensive printer repairs and bank check reject fees

due to inferior MICR toner formulation.

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

MICR Check Stock

Check stock has a significant impact on the resulting quality and security of your MICR

document. Here are a few features that should be considered when selecting a check

stock. Please see Chapter 5: Security Issues for more information on check stock

security features.

Quality

Quality MICR check printing with your Source Technologies’ secure MICR printer

requires check stock that matches the printer’s requirements. Source

Technologies can supply paper specifically made for our printers. If you wish to

order check stock from other suppliers, please show the following requirements

to your sales representative. We will test other suppliers’ paper for a nominal fee.

Layout

Layout your check design before any paper is purchased or layout your design to

existing check stock. Keep perforations, orientation, special logos and any color

elements in mind. The printer can print just about anything as long as it is black.

Weight

We recommend 24 lb. - 29 lb. paper.

Stiffness

We recommend Taber M.D. 2.5 and C.D. 1.1 minimum.

Smoothness

For best toner fusing, we recommend rougher surfaces within the base printers’

specifications, and the Paper Specifications for Checks, X9.100.10. We

recommend a smoothness range of 150 to 200, Sheffield.

Paper Grain Direction

When using 24 lb. - 29 lb. bond paper we generally support either long or short

paper grain. Overall performance in the bank’s reader/sorters is best when the

resultant grain direction is left to right when viewing the check.

Perforations

All perforations in the stock should be Laser-Cut or Micro-Perfs (20 or more cuts

per inch). Larger perforations can produce excessive paper chaff and result in

damage to the toner cartridge. Perforations should be ironed by the paper

supplier to reduce nesting and potential double feeding.

Moisture

The paper moisture content should be between 4.7 and 5.5%. Storage conditions

have much to do with the final moisture content of most papers. Store your check

stock in a cool, dry, environmentally stable and secure area. Protective

wrappings should be removed just prior to use.

Quality Issues | 4

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

5. Security Issues

Printing negotiable documents from blank paper on desktop MICR laser printers makes

security a top priority for any company embarking on a desktop check printing project.

Combating fraud is a moving target. As soon as a new weapon is developed, malicious

forces are at work to devise workarounds to it. Good security programs integrate

hardware, software, your employees, processes, and your financial institution into a

secure check production system. The ultimate liability for fraudulent documents rests

with the banks and their customers, and there can be many vulnerable points throughout

the overall system. Customers must have systems designed and documented to show

“Ordinary Care and Good Faith Effort” is in place to avoid liability. In the past, financial

institutions generally credited corporations when fraud was discovered. Today,

regulations attempt to define who may have been negligent in the transaction and put

the liability on that party or parties. If a fraudulent occurrence can be traced to a

corporation’s lack of security procedures or the design of their negotiable documents,

the regulations will protect the banks, or at best case the loss will be shared.

The following internal and external security measures will help minimize your risk of

check fraud.

1. Stay abreast of current check fraud methods and the latest in fraud detection.

Many financial institutions offer seminars to educate corporate clients.

2. Financial institutions should train tellers to look at the check, not the person

presenting the check. The check, not the person, is the item that must be

verified.

3. Incorporate security features into your base check stock and utilize printed

security features that address both alteration and counterfeiting of original

items. We have found the following check stock security features to be of

merit:

Artificial Watermarks - White on white printing generally on the back reveals

words or patterns when held at an angle. You should state on the front of the

check that this feature is present. True watermarks are valuable but more

costly.

Laid Lines - Background lines that make cut and paste alteration difficult.

These are normally on the back of the check.

Fuse Enhancing Additive - Coatings or additives to the paper that improve

the bonding of toner to the paper. This helps prevent altering of critical data

such as the amount, or payee name.

Chemical Additives - If an ink eradicator (bleach, acetone, etc.) is applied to

the document, the eradicator creates a permanent stain.

Numbered Check Stock - Sequential numbering printed in dye that

penetrates to the reverse side of the check can be used to verify authenticity.

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

This also provides for inventory control of blank check stock. This number

should not be linked or be equal to the check serial number due to the

potential of double feeding in laser printers.

Note: These features serve as a general guide for check security. You

should not consider these features as an all inclusive list. We

recommend consulting with your paper supplier for any additional

comments or suggestions.

4. Firms accepting checks should be aware of damaged MICR lines.

Intentionally damaging the MICR line can increase the time necessary to

process an item, giving the forger enough time to leave town. Also be

sensitive to discoloration, this could be an indication of alteration.

5. Safeguard check stock paper, and limit access only to necessary employees.

6. When generating final negotiable items:

• The document always includes the amount value in words

• The document should not include information that limits the value

range, i.e. “Not valid over $500.” This only guides the fraudulent

attempt. Use your application software to detect out of range items

• All levels of hardware and software password protection should be

utilized

7. Understand and approve the security procedures of your check stock

suppliers to safeguard stock in their custody.

8. Use “Positive Pay” check services from your financial institution. You should

provide the check number, check date, dollar amounts, and sometimes the

payee name to your bank when checks are issued. The bank will match these

values and alert you to mismatches before clearing the check to your

account. Financial institutions should encourage full participation of corporate

clients.

9. Move methods of fraud detection to the item’s point of entry into the clearing

system. For example, low cost readers can detect low magnetic strength in

the MICR line which is a good indication of attempts to copy an original.

10. Review and document your internal negotiable document printing procedures.

Investigate employee backgrounds before assigning security authority. Split

the responsibilities. For example, an accounts payable production/security

officer should not also balance the account.

Security Issues | 5

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

6. MICR Features

Source Technologies’ secure MICR printers are designed to allow both general office

document printing and secure MICR document printing. You may print a variety of

conventional jobs with MICR toner using all of the printer features available. These

printers come standard with PCL5e, PCL6, and PostScript Level 2 emulation. Source

Technologies has designed features to enhance the base printer for MICR specific

printing that allows you to securely print high quality negotiable documents.

Secure MICR

Source Technologies’ secure MICR printers have resident fonts for printing MICR

documents, password secured in Flash memory. Specific PJL commands are required to

unlock and relock these font resources. While unlocked, they can be accessed with

standard PCL5e commands. Please refer to Chapter 7 for more information. In addition

to the secured font resources, the printer has been internally modified to ensure high

quality printing with MICR toner. Specific print densities, transfer voltages and fusing

temperatures are factory pre-set. Source Technologies’ secure MICR printers only

support Source Technologies MICR toner cartridges.

MICR Fonts

The E-13B MICR font, designed specifically for the printer, is resident in your printer.

Examples of the font characters are in Appendix A of this manual. The font can only be

activated after the appropriate PJL commands with the correct password have been sent

to the printer. The alternative MICR Font used in some countries, CMC7, is also resident

in your printer.

Secure Fonts

Two Source Technologies’ designed numeric secure fonts, Secure Numeric and ICR

Secure Numeric, are resident and password protected in Flash memory in your printer.

Examples of these fonts can be found in Appendix B of this manual. Like the MICR font,

these fonts can only be accessed after sending PJL commands with the correct

password from your application software.

The ICR Secure Numeric Font is designed for use in the Convenience Amount area of a

check. This area contains the numeric dollar value and is located on the right side of the

check approximately 2 inches up from the bottom edge. The imaging recognition

features available in today’s check reader/sorter equipment can optically read it. The

Secure Numeric Font should not be used in this area of the check. It is a reverse image

font and cannot be read automatically by the equipment.

It is recommended that both fonts are used as they are designed to deter check fraud.

MICR Features | 6

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

MicroPrint

Your secure MICR printer also contains the MicroPrint font. MicroPrint text, being less

than .010” tall, can be easily read with a magnifying glass but appears as a solid line to

the unaided eye. This font provides protection against reproduction by most scanners

and copiers because they cannot successfully print the tiny letters.

Most check printers use this font in the signature area of their preprinted checks. It is

recommended that this font be used to help deter check fraud. The text in this font can

be either fixed (such as the name of your organization) or it can be variable (such as the

check amount and payee name). The use of variable text provides an additional method

of protection against check counterfeiters.

Use of the “MP” designate symbol to identify the line as MicroPrint is optional. The

MicroPrint font only contains alphanumeric characters. Punctuation marks and spaces

are ignored by this font and do not print.

Resource Storage

The Flash memory in the printer contains five Source Technologies’ secured fonts but

can be loaded with additional resources for check or non-check printing. The Flash can

be loaded with signature fonts, overlay Macros, or other custom resources limited only

by the available space. Flash memory in the ST-9612 is read/write password protected.

To load additional resources to Flash requires the proper PJL commands to unlock the

Flash memory device. This will be detailed in Chapter 7.

Storing resources (fonts, Macros, etc.) in RAM is also an option. Resources in RAM are

deleted when the printer is powered off and cannot be password protected in the printer.

MICR Toner Cartridge

A Source Technologies’ secure MICR printer only supports Source Technologies’ MICR

Toner Cartridges. The printer will display an error condition when a standard cartridge is

installed. When a MICR toner cartridge is installed the following occurs:

Control of image density or print density is set to optimum levels for MICR

printing.

When the PJL “MICRJOB” command is sent, the following occurs:

1. The printer forces internal copies to 1. Downloaded copy commands are

ignored.

2. Automatic reprint of jammed documents is disabled, forcing the application to

reprint any jammed documents. This provides an audit trail to the application

of the jam event.

MICR Features | 6

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

The PJL commands to unlock the fonts must precede all PCL commands. The re-lock

PJL commands must follow the PCL commands and final form feed command. The PCL

commands can print an unlimited number of pages between the unlock and re-lock

sequences. The following examples will use <ESC> to indicate the Escape character,

ASCII 27. Values shown in parentheses () are hexadecimal.

PJL Unlock Sequence

<ESC>%-12345X@PJL LDECLARE LRESOURCE:”flash:” LRWLOCK=”PASSWORD”

(0D)(0A)@PJL ENTER LANGUAGE=PCL(0A)

The sequence contains a UEL (Universal Exit Language) command followed by the

unlock and enter language commands. These commands are case sensitive.

PASSWORD is the initial default password value. The command delimiter is a Line Feed

(hex 0A) with Carriage Return (hex 0D) being optional. Spaces are required as shown.

The ENTER LANGUAGE command is optional but recommended. The command should

also end with a LF (hex 0A). At this time all secured resources including any resources

that are customer unique in Flash are unlocked and available to PCL.

The password value is limited to no more than 8 alphanumeric, case-sensitive

characters.

PJL Re-Lock Sequence

<ESC>%-12345X@PJL LDELETEPASSWORD LRESOURCE:”flash:”(0D)(0A)

<ESC>%-12345X

This sequence re-locks the resources with no change in the password value. The PJL

syntax of LDELETEPASSWORD is not the password. The command sequence

terminates with the UEL command (Universal Exit Language). This is optional but

recommended.

PJL Re-Lock Sequence With A New Password Value

<ESC>%-12345X@PJL DEFAULT LRESOURCE:”flash:” LRWLOCK=”xxxxxxxx”

(0D)(0A)<ESC>%-12345X

This command requires the resources to be previously unlocked. The new password is

represented by the value xxxxxxxx. The UEL is again optional but recommended.

After consulting Lexmark Technical Reference materials you may wish to expand the

PJL sequences to include more than the examples above. To chain multiple PJL

commands, follow the following format:

(UEL)(PJL COMMAND)(0A)(PJL COMMAND)(0A)(PJL COMMAND)(0A)(UEL or

ENTER LANGUAGE)

The normal printer action to any format problems or missing or extra symbols is to ignore

the PJL command. This may make it difficult to troubleshoot format errors.

PCL Font Call Commands

After PJL has unlocked the MICR Flash resources, the ST9612 uses standard PCL5e

commands to print. The five resident Source Technologies MICR font resources are all

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

bitmapped fonts and therefore cannot be scaled larger or smaller than the bitmapped

images. These fonts can be called by either a PCL Font Selection String or by their ID.

The commands are:

E13B MICR FONT <ESC>(10O<ESC>(s0p8h8v0s7b360T

<ESC>(30802X

The Selection String

The ID Call

SECURE NUMERIC <ESC>(16C<ESC>(s0p5h36v0s112T

<ESC>(30043X

The Selection String

The ID Call

ICR SECURE <ESC>(1O<ESC>(s1p12v0s0b110T

<ESC>(30066X

The Selection String

The ID Call

CMC7 MICR FONT <ESC>14Y<ESC>(s0p8h8v0s0b361T

<ESC>(30803X

The Selection String

The ID Call

MicroPrint <ESC>(2Q<ESC>(s1p1v0s0b112T

<ESC>(30055X

The Selection String

The ID Call

MICR FONT NOTE – The E-13B and CMC7 Fonts are 8 characters per inch. To position

correctly at an exact 8 characters per inch, the printer must be set to an internal Unit of

Measure of 600 DPI or greater or must have a horizontal motion index command at 8

CPI be issued after the font call. This is true even if the base printer is set at 600 DPI.

The default character positioning is at 300 DPI, and 300 divided by 8 equals 37.5 pixels.

The printer will either round down to 37 or up to 38 pixels causing characters to creep.

There are multiple ways to resolve this:

1. If you are using a printer driver set to 600 DPI, the printer data stream should

include a Unit of Measure PCL command set to 600. The command is

<ESC>&u600D

2. If the application controls the printer data stream, add the Unit of Measure

command early in the data stream. The command also affects X & Y positioning

commands. Add <ESC>&u600D

3. After calling the E-13B MICR font, issue an HMI (Horizontal Motion Index)

command set to 8 characters per inch.

<ESC>&k15H

The command must be included with every E-13B MICR font call using either the

Selection String or ID call. The command string is:

<ESC>(10O<ESC>(s0p8h8v0s7b360T<ESC>&k15H font data——The Selection

String

<ESC>(30802X<ESC>&k15H font data——The ID Call

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Refer to the Font Mapping Appendix pages for specific character set data for each

font.

PJL INFO MICR COMMAND

Source Technologies’ secure MICR printers support an optional custom bi-directional

PJL Inquiry Command. The command provides printer and cartridge information for

network management. The command format is: @PJL INFO MICR.

The command should be sent with UEL (Universal Exit Language) commands.

Example:

<ESC>%-12345X UEL

@PJL INFO MICR INFO MICR Command

<ESC>%-12345X UEL

The following data is returned

@PJL INFO MICR

PRINTER STATE = READY

= BUSY

= NOT READY

SERIAL NUMBER = XXXXXXXX

PAGECOUNT = 123456

CARTRIDGE TYPE = NORMAL

= MICR

CARTRIDGE STATUS = UNKNOWN

= OK

= LOW

= EMPTY

CARTRIDGE SERIAL# = XXXXXXXX

TONER LEVEL = 0-9

= UNKNOWN

CARTRIDGE COUNT = XXXX

LOW THRESHOLD = XXXX

EMPTY THRESHOLD = XXXX

• Printer State

“Ready” is the expected return

• Serial Number = Printer Serial Number

• Page Count = Printer Page Count

• Cartridge Type

“MICR” is the expected return. “Normal” could mean the command was sent

to a non-MICR printer

• Cartridge Status

“OK, Low, and Empty” are the expected returns. “Unknown” is possible if the

cartridge had just been installed.

• Cartridge Serial = Cartridge Serial Number

• Toner Level

A single digit return giving a rough estimate of toner remaining

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

9 = Full, 0 = Empty

• Cartridge Count = xxxx

Data indicating toner usage by counting pixels printed

• Low Threshold = xxxx

The Toner Low point based on cartridge count value

• Empty Threshold = xxxx

A cartridge count value that determines when printing must stop to ensure

quality MICR documents

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Toner Cartridge and Photoconductor Units

The ST9612 MICR Print Cartridge is comprised of two components: the toner cartridge

and the photoconductor unit.

Toner cartridges are available in two models depending on the yield: a 1.5K page and a

3K page. The 1.5K model ships with new printers. The 3K model is the normal

replacement model. The projected life in terms of page count is based on a typical 5%

print coverage and continuous print mode. These projected values of 1,500 and 3,000

were certified using the ISO 19752 Yield Testing Methodology. The standard requires

continuous print mode. The projected life is reduced somewhat dependent on the actual

average print-job page count.

The photoconductor unit has a projected life in terms of page count of 20,000 to 30,000

dependent on average pages per print job. The 20,000 life is projected for 100% 1 page

print jobs. The 25,000 life is projected for an average print job being at or near 3 pages.

The photoconductor life for average print jobs being above 3 pages would exceed the

25,000 forecast.

The ST9612 MICR printer keeps record of the actual printing modes in terms of average

print job size and the actual average print coverage percentage. The printer internally

adjusts when either the toner cartridge or photoconductor unit needs to be replaced.

The following error messages pertain to the toner and photoconductor unit.

Toner Low

The printer will stop with the Toner Low / Replace PC light and the Continue button ON

steady. Press the Continue button and the printer will return to Ready and continue

printing. The Toner Low light will remain ON, steady. While in the toner low state, the

printer will stop again on power cycles and other operating situations such as jams or

paper out conditions. Simply press the button to continue printing. The Toner Low light

will remain ON until the cartridge is replaced or Toner Out is reached.

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Toner Out

After approximately 300 pages beyond the first Toner Low condition the printer will stop

printing and display the Toner Out condition. The Toner Low light will be ON steady and

the Error light will blink. All other lights will be off. You must replace the toner cartridge to

continue printing.

Photoconductor Unit Life Warning

As mentioned above, the printer internally calculates the average print-job size and

actual average print coverage percentage. Once the photoconductor unit reaches

approximately 85% of it usable life, the printer will stop with the Continue button ON. The

Toner Low / Replace PC will be BLINK. Press Continue and the printer returns to Ready

and printing will continue. This early warning is intended to provide a reasonable time

for scheduling and obtaining a new unit for replacement.

When 100% of the usable life has been reached, the Menus Page will indicate the

photoconductor life is “Exhausted”. The printer will still continue to print, but it is

recommended the Photoconductor be replaced soon. The exposure for print quality

related problems may be close due to printing beyond the projected usable life.

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Replace Photoconductor (printer hard stop)

After the photoconductor unit exceeds 15% beyond the usable life point, the printer will

hard stop with the Error and Toner Low / Replace PC lights BLINKING and the Continue

button ON. If you press Continue, one page will print with instructions in multiple

languages to replace the Photoconductor Unit referring to Appendix F.

Load MICR Toner

The Source Technologies’ Secure MICR Printer only supports MICR toner cartridges in

its normal configuration. This prevents the printing of MICR documents with standard

toner. If configured to support both MICR and standard cartridges, the PJL MICRJOB

command checks the cartridge type and will prompt the operator with the following

pattern to load MICR toner if not present.

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

PJL Re-Lock Sequence

The last two lines re-lock the secured fonts. The password is not changed in this

example.

FIGURE 8.1 SAMPLE ACCOUNTS PAYABLE CHECK

MICR Command Example | 8

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

PJL and PCL commands used to print the sample check:

<ESC>%-12345X@PJL LDECLARE LRESOURCE:"flash:" LRWLOCK="PASSWORD"

@PJL MICRJOB

@PJL ENTER LANGUAGE = PCL

<ESC>&l2a1h6d1e64F

<ESC>&u600D

<ESC>&f100y3X

<ESC>(s4099t0b10H

<ESC>*p300x600Y xxxxxxxxx xx/xx/xxxx $x,xxx.xx 3% $x,xxx.xx

<ESC>*p300x2775Y xxxxxxxxx xx/xx/xxxx $x,xxx.xx 3% $x,xxx.xx

<ESC>*p3250x75Y<ESC>(s4099t3b8H 123456

<ESC>*p3250x2200Y 123456

<ESC>*p4250x4450Y 123456

<ESC>*p3650x4775Y xx/xx/xxxx

<ESC>*p400x5225Y<ESC>(s4099t0b15H xxxxx Thousand xxxxx Hundred xxxxx

Dollars and xx/100 Cents

<ESC>*p600x5600Y<ESC>(s10H ABC TOOL & DIE

<ESC>*p600x5700Y 123 Main Street

<ESC>*p600x5800Y Yourcity, ST 12345-6789

<ESC>*p900x6325Y<ESC>(30802X<ESC>&k15H O123456O T123456780T

12345D67890O

<ESC>*p1500x5100Y<ESC>(30043X ($**1,234.56)

<ESC>*p3650x5400Y<ESC>(30066X $**1,234.56

<0C> Form Feed

<ESC>%-12345X@PJL LDELETEPASSWORD LRESOURCE:"flash:"

<ESC>%-12345X

MICR Commands | 7

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Appendix B: Secure Numeric Font Mapping

Description Alpha/Numeric Hex Value Secure Font Character

Character

Dollar Sign $ 23

Left Bracket ( 28

Right Bracket ) 29

Asterisk * 2A

Comma , 2C

Dash - 2D

Period . 2E

Slash / 2F

Zero 0 30

One 1 31

Two 2 32

Three 3 33

Four 4 34

Appendix B

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Appendix B continued: Secure Numeric Font Mapping

Description Alpha/Numeric Hex Value Secure Font Character

Character

Five 5 35

Six 6 36

Seven 7 37

Eight 8 38

Nine 9 39

Arrow > 3E

Example:

Note: The secure fonts in the example are magnified for purposes of clarity.

Appendix B

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Semi-Colon ; 3B

Less Than < 3C

Equal = 3D

Greater Than > 3E

Note: The CMC7 Font in the example above is magnified for purposes of clarity.

Appendix D

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Appendix E: Contact

For more information, contact:

Source Technologies LLC.

2910 Whitehall Park Drive

Charlotte, NC 28273

www.sourcetech.com

techsupport@sourcetech.com

800.922.8501

Appendix E

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Appendix F: Photoconductor Replacement

Source Technologies, LLC ST9612 Secure MICR Printer User’s Guide

Source Technologies Secure Micr Printer St9612 Users Manual

STI MICR ST9620 st9612-user-guide

ST9612 to the manual 219b050f-7328-46f4-a18b-ebdd0261a79e

Navigation menu

Versions of this User Manual:

Views

Navigation