Southbend Sb1015f Sb1012_m1 User Manual To The 958c5c0f 05a7 4965 97e6 38e48b6d1645

User Manual: Southbend sb1015f to the manual

Open the PDF directly: View PDF .
Page Count: 148

Download
Open PDF In Browser	View PDF

MODEL SB1015F
16" X 60" LATHE 440V w/DRO
Manual Insert
PHONE: (360) 734-1540 • www.southbendlathe.com

The Model SB1015F Lathe is the same machine as the Model SB1015 except for the following:
•

Added a 2-Axis Fagor Digital Readout (DRO).

Except for the differences noted in this insert, all other content in the Model SB1015 Owner’s Manual
applies to this machine. Before operating your new lathe, you MUST read and understand this insert,
the entire Model SB1015 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of
injury when using this machine. Keep this insert for later reference.
If you have any further questions about this manual insert or the differences between the Model
SB1015F and the Model SB1015, contact our Technical Support at (360) 734-1639 or email
sales@southbendlathe.com.

New & Changed Parts
2407

2318

F
015
SB1EVS
DEL60" M
MO16" OxLRO/DORO
TO HE w
LAT

l Nu

Seria

G Da

2416

REF

PART #

2318 PSB1014F2318
2407 PSB1015F2407
2416 PSB1015F2416

1"
: 5. lock
avel Cam
d Tr D1-6 "
pounose: 16 T#6
Comdle N re: 2-1/dle: M T#4
M
Spindle Bo Spin tock:
z
s
de
60H
ation
Spin r Insi Tails
Ph,
de
ecific
, 3- .75A
Taper Insi 00 lbs. nd Sp
0V
10
Be
:
Tape t: 33 South
"
P, 44 raw 4"
to
gh
7.5H p D .1 s: 60 "
IS
Wei Taiwan
or: Am d: 16 nter .375
in
G TH
Mot Load r Be n Ce e: 10
" Made
SIN
ve
id
EU
Full g O Betwee s Sl 5" .): 10.2
IL
in e Cros 22.9 ax
G! WH
Sw tanc r
: (M
ve
Dis g O r GapGap
NIN JURY
in ve
.
AR AL IN
Sw g O ose Toel: 9"
urce
in
! W PERSON
Sw dle N e Trav
er so ir and
S
ting.
Spin s Slid
pow
OU
ha
ed
star
ng
SERI
Cros
fore
ound
OF
l.
re lo
l beection. a gr ; secu ents. coho
RISK
to
m al
anua
prot ted
elry
THE
m
e
justugs orting.
ec
jew
nd ey
UCE
or ad dr star d has
rstaoved is conn es, or
RED
ce, ce of fore .
an
ov
TO INE: d undeappr hine
an
k
gl
en
be
in
r
en
e. ,
CH
sk uc
MA ad ans wea e macplacothing maint e influ
et up ith e ch
th in e cl
e, der thsted/sact w in th the.
ay
re
ic
ds
1. Re
lw su ar os
rv
ju nt ld la
2. A ake all guear loves. re se or unly adoid co ly heg the
re
fo ed
3. M
eep OT w slee be n tir oper d av secu ar tin
n.
4. KO N longpowerwhe is prrly an and fore st motio
in
ing.
5. Droll upnnect erateachinegula erly n bek.
turn ne.
it is
re op tio
d. are achi
isco OT opthe m id is pr rota chuc hen
6. DDO N sure ng fluiece h fullin the ce w ed. ppor tel youthe m
7. ake cuttiworkproug key orkpieattendly suateriass to
8. M angesure nce thchuck or w g un operthe m acce
k nnin e pr for ised
e
e
ra
9. Ch
uc
Mak clea e th ch ru s ar te rv
10. safe leavh the lathe ieceeed ra supe
er uc the orkp sp un
ev
to e w er ve
N
11. Never leav long prop to ha
12. Nevere sure e the ildren
13. Mak s us w ch
14. Alwayt allo
15. Do no
16.

DESCRIPTION
DRO ASSEMBLY FAGOR 20i-T 2-AXIS
MACHINE ID LABEL
MODEL NUMBER LABEL

Copyright © June, 2011 by South Bend Lathe Co.
WARNING: No portion of this manual may be reproduced without written approval.
#BL14236 Printed in USA

Model SB1015F

MANUAL INSERT

Mfg. Since 4/11

0RGHO6%)

6RXWK%HQG[/DWKH9ZLWK'52
2TQFWEV&KOGPUKQPU
9GKIJV NDU
9KFVJ UKFGVQUKFG Z&GRVJ HTQPVVQDCEM Z*GKIJV ZZKP
(QQVRTKPV .GPIVJZ9KFVJ ZKP

5JKRRKPI&KOGPUKQPU
6[RG 9QQF5NCV%TCVG
%QPVGPV /CEJKPG
9GKIJV NDU
.GPIVJZ9KFVJZ*GKIJV ZZKP

'NGEVTKECN
2QYGT4GSWKTGOGPV 82JCUG*\
(WNN.QCF%WTTGPV4CVKPI #
/KPKOWO%KTEWKV5K\G #
+PXGTVGT6[RG ;CUMCYC)#2
5YKVEJ /CIPGVKEYKVJ6JGTOCN2TQVGEVKQP
5YKVEJ8QNVCIG 8
2NWI+PENWFGF 0Q
4GEQOOGPFGF2NWI1WVNGV6[RG *CTFYKTGVQ.QEMKPI&KUEQPPGEV5YKVEJ

/QVQTU
/CKP
6[RG 6'(%+PFWEVKQP
*QTUGRQYGT *2
8QNVCIG 8
2JCUG 2JCUG
#ORU #
5RGGF Ō42/
%[ENG *\
0WODGTQH5RGGFU 8CTKCDNG
2QYGT6TCPUHGT 8$GNV)GCT
$GCTKPIU 5JKGNFGFCPF2GTOCPGPVN[5GCNGF

/QFGN5$(

-2-

2CIGQH

Mfg. Since 4/11

MANUAL INSERT

Model SB1015F

.WDTKECVKQP
6[RG 6'(%+PFWEVKQP
*QTUGRQYGT *2
8QNVCIG 8
2JCUG 2JCUG
#ORU #
5RGGF 42/
%[ENG *\
0WODGTQH5RGGFU
2QYGT6TCPUHGT &KTGEV&TKXG
$GCTKPIU 5JKGNFGFCPF2GTOCPGPVN[5GCNGF
%QQNCPV
6[RG 6'(%+PFWEVKQP
*QTUGRQYGT *2
8QNVCIG 8
2JCUG 2JCUG
#ORU #
5RGGF 42/
%[ENG *\
0WODGTQH5RGGFU
2QYGT6TCPUHGT &KTGEV&TKXG
$GCTKPIU 5JKGNFGFCPF2GTOCPGPVN[5GCNGF

/CKP5RGEKHKECVKQPU
1RGTCVKQP+PHQ
5YKPI1XGT$GF KP
&KUVCPEG$GVYGGP%GPVGTU KP
5YKPI1XGT%TQUU5NKFG KP
5YKPI1XGT5CFFNG KP
5YKPI1XGT)CR KP
/CZKOWO6QQN$KV5K\G KP
%QORQWPF6TCXGN KP
%CTTKCIG6TCXGN KP
%TQUU5NKFG6TCXGN KP
*GCFUVQEM+PHQ
5RKPFNG$QTG KP
5RKPFNG6CRGT /6
0WODGTQH5RKPFNG5RGGFU 8CTKCDNG
5RKPFNG5RGGFU Ō42/
5RKPFNG6[RG &%CONQEM
5RKPFNG$GCTKPIU 05-QT0606CRGTGF4QNNGT
5RKPFNG.GPIVJ
5RKPFNG.GPIVJYKVJ,CY%JWEM KP
5RKPFNG.GPIVJYKVJ,CY%JWEM KP
6CKNUVQEM+PHQ
6CKNUVQEM3WKNN6TCXGN KP
6CKNUVQEM6CRGT /6
6CKNUVQEM$CTTGN&KCOGVGT KP

/QFGN5$(

2CIGQH

-3-

Model SB1015F

MANUAL INSERT

Mfg. Since 4/11

6JTGCFKPI+PHQ
0WODGTQH.QPIKVWFKPCN(GGFU
4CPIGQH.QPIKVWFKPCN(GGFU ŌKP
0WODGTQH%TQUU(GGFU
4CPIGQH%TQUU(GGFU ŌKP
0WODGTQH+PEJ6JTGCFU
4CPIGQH+PEJ6JTGCFU Ō62+
0WODGTQH/GVTKE6JTGCFU
4CPIGQH/GVTKE6JTGCFU ŌOO
0WODGTQH/QFWNCT2KVEJGU
4CPIGQH/QFWNCT2KVEJGU Ō/2
0WODGTQH&KCOGVTCN2KVEJGU
4CPIGQH&KCOGVTCN2KVEJGU Ō&2
&KOGPUKQPU
$GF9KFVJ KP
.GCFUETGY&KCOGVGT KP
.GCFUETGY62+
.GCFUETGY.GPIVJ KP
5VGCF[4GUV%CRCEKV[ ŌKP
(QNNQY4GUV%CRCEKV[ ŌKP
(CEGRNCVG5K\G KP
(GGF4QF&KCOGVGT KP
(NQQTVQ%GPVGT*GKIJV KP
*GKIJV9KVJ.GXGNKPI,CEMU KP
%QPUVTWEVKQP
$CUG %CUV+TQP
*GCFUVQEM %CUV+TQP
*GCFUVQEM)GCTU (NCOG*CTFGPGF5VGGN
$GF +PFWEVKQP*CTFGPGFCPF)TQWPF%CUV+TQP
5VCPF %CUV+TQP

1VJGT
%QWPVT[1H1TKIKP 6CKYCP 5QOG%QORQPGPVU/CFGKP75#CPF,CRCP
9CTTCPV[ ;GCT
5GTKCN0WODGT.QECVKQP +&.CDGNQP4GCT5KFGQH.GHV5VCPF
#UUGODN[6KOG #RRTQZKOCVGN[*QWT

(GCVWTGU
#NNGP$TCFNG['NGEVTKECN%QORQPGPVU
(CIQT&41
/GGJCPKVG%CUVKPI5KIPCVWTG5QWVJ$GPF89C[$GF
5CHGV[%JWEM)WCTFYKVJ/KETQ5YKVEJ5JWV1HH
*CNQIGP9QTM.KIJV
9C[6QQN2QUV
%QORNGVG%QQNCPV5[UVGO
/KETQOGVGT%CTTKCIG5VQR
6JTGCFKPI&KCN+PFKECVQT
05-QT060,CRCPGUG5RKPFNG$GCTKPIU
(WNN.GPIVJ5RNCUJ)WCTF
(TQPV4GOQXCDNG5NKFKPI%JKR6TC[
;CUMCYC)#2+PXGTVGT
%QORNGVGN['PENQUGF7PKXGTUCN)GCTDQZHQT%WVVKPI+PEJ/GVTKE/QFWNCTCPF&KCOGVTCN2KVEJGU
2TGUUWTK\GF.WDTKECVKQP5[UVGOHQT*GCFUVQEM)GCTUCPF$GCTKPIU
&KCN%QPVTQNNGF8CTKCDNG5RKPFNG5RGGFUYKVJ&KIKVCN4GCF1WV
,QI$WVVQPCPF'OGTIGPE[5VQR
/QFGN5$(

-4-

2CIGQH

14" & 16" EVS TOOLROOM LATHES
MODELS SB1012/SB1014/SB1037 - 220V
MODELS SB1013/SB1015/SB1038 - 440V

OWNER'S MANUAL

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906!

For Machines Mfg. Since 7/09

Scope of Manual
This manual helps the reader understand the machine, how to prepare it for operation, how to control
it during operation, and how to keep it in good working condition. We assume the reader has a basic
understanding of how to operate this type of machine, but that the reader is not familiar with the
controls and adjustments of this specific model. As with all machinery of this nature, learning the
nuances of operation is a process that happens through training and experience. If you are not an
experienced operator of this type of machinery, read through this entire manual, then learn more
from an experienced operator, schooling, or research before attempting operations. Following this
advice will help you avoid serious personal injury and get the best results from your work.

Manual Feedback
We've made every effort to be accurate when documenting this machine. However, errors sometimes
happen or the machine design changes after the documentation process—so the manual may not
exactly match your machine. If a difference between the manual and machine leaves you in doubt,
contact our customer service for clarification.
We highly value customer feedback on our manuals. If you have a moment, please share your
experience using this manual. What did you like about it? Is there anything you would change to
make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use?
South Bend Lathe, Inc.
C
/O Technical Documentation Manager
P.O. Box 2027
Bellingham, WA 98227
Email: manuals@southbendlathe.com

Updates
For your convenience, any updates to this manual will be available to download free of charge
through our website at:
www.southbendlathe.com

Customer Service
We stand behind our machines. If you have any service questions, parts requests or general questions
about your purchase, feel free to contact us.
South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
Fax: (360) 676-1075 (International)
Fax: (360) 734-1639 (USA Only)
Email: cs@southbendlathe.com

Table of Contents
INTRODUCTION ....................................................3
About These Machines......................................... 3
Foreword ............................................................. 3
Capabilities ......................................................... 3
Features .............................................................. 3
Identiﬁcation ........................................................ 4
SAFETY..................................................................5
Understanding Risks of Machinery .................... 5
Basic Machine Safety .......................................... 5
Additional Metal Lathe Safety ............................ 7
PREPARATION ......................................................8
Preparation Overview.......................................... 8
Things You'll Need ............................................... 8
Unpacking ............................................................ 8
Inventory .............................................................. 9
Cleaning & Protecting ....................................... 10
Location .............................................................. 11
Physical Environment........................................ 11
Electrical Installation ........................................ 11
Lighting ............................................................ 11
Weight Load ...................................................... 11
Space Allocation ................................................ 11
Lifting & Moving ................................................ 12
Leveling & Mounting ......................................... 13
Leveling ............................................................ 13
Bolting to Concrete Floors .................................. 14
Assembly ............................................................ 14
Lubricating Lathe .............................................. 14
Adding Cutting Fluid......................................... 15
Power Connection .............................................. 15
SB1012 (220V 3-Phase) ...................................... 15
SB1014, SB1037 (220V 3-Phase) ........................... 15
SB1013 (440V 3-Phase).......................................... 15
SB1015, SB1038 (440V 3-Phase) ........................... 15
Connecting Power Cord to Lathe ........................ 16
Hardwiring Lathe to Power Source .................... 16
Correcting Out-of-Phase Wiring ......................... 17
Test Run ............................................................. 17
Spindle Break-In ................................................ 21
Recommended Adjustments .............................. 22
OPERATION ........................................................23
Operation Overview ........................................... 23
Description of Controls & Components ............ 24
Main Power Switch ............................................ 24

Headstock Controls............................................ 24
Carriage Controls .............................................. 24
Control Panel .................................................... 25
Tailstock Controls.............................................. 26
Foot Brake ........................................................ 26

Chuck & Faceplate Mounting ........................... 27
Removing Chuck or Faceplate ............................ 27
Mounting Chuck or Faceplate ............................ 28
Installing and Adjusting Camlock Studs............. 29
3-Jaw Chuck....................................................... 30
Changing Jaws .................................................. 31
Mounting Workpiece .......................................... 31
4-Jaw Chuck....................................................... 32
Mounting Workpiece .......................................... 32
Tailstock ............................................................. 32
Moving Along Bedway ....................................... 33
Using Quill ........................................................ 33
Installing Tooling .............................................. 33
Removing Tooling .............................................. 33
Offsetting .......................................................... 34
Aligning ............................................................ 34
Faceplate ............................................................ 36
Mounting Workpiece with Clamps...................... 36
Mounting Workpiece Between Centers ............... 36
Centers ............................................................... 37
Dead Centers ..................................................... 37
Live Centers ...................................................... 37
Mounting Dead Center in Spindle ...................... 37
Removing Center from Spindle........................... 38
Mounting Center in Tailstock............................. 38
Removing Center from Tailstock ........................ 38
Steady Rest ........................................................ 39
Follow Rest ......................................................... 39
Compound Slide ................................................. 40
Four-Way Tool Post ........................................... 40
Aligning Cutting Tool with Tailstock Center....... 41
Aligning Cutting Tool with Tailstock Center....... 41
Adjustable Apron Stop System ......................... 42
Carriage Stop ..................................................... 42
Manual Feed ...................................................... 43
Carriage Handwheel .......................................... 43
Compound Slide Handwheel .............................. 43
Spindle Speed ..................................................... 43
Determining Spindle Speed................................ 43
Setting Spindle Speed ........................................ 44

Power Feed ......................................................... 44
Power Feed Controls .......................................... 45
Understanding Thread & Feed Rate Chart ......... 46
Positioning Gearbox Levers................................ 46
End Gear Setup ................................................. 47
Threading Controls ............................................ 48
Power Feed Lever .............................................. 48
Half Nut Lever .................................................. 48
Thread Dial & Chart Overview .......................... 48
Using Thread Dial and Chart ............................. 49
Chip Drawer ....................................................... 50
Cutting Fluid System ........................................ 51
ACCESSORIES ...................................................52
Accessories ......................................................... 52
MAINTENANCE ...................................................54
Maintenance Schedule....................................... 54
Cleaning ............................................................. 54
Maintenance Chart ............................................ 55
Lubrication ......................................................... 56
Headstock ......................................................... 56
Gearbox ............................................................. 58
Apron ................................................................ 58
Lead Screw & Feedrod Bearings ........................ 59
Lead Screw ........................................................ 59

Ways & Slides ................................................... 59
Unpainted & Machined Surfaces ........................ 59
Ball Oilers ......................................................... 60
Cleaning Electrical Box Filter ............................ 60
End Gearing ..................................................... 61

Cutting Fluid System ........................................ 62
Hazards............................................................. 62
Adding Fluid ..................................................... 62
Changing Cutting Fluid ..................................... 63
Machine Storage ................................................ 64
SERVICE ..............................................................65
Backlash Adjustment ........................................ 65
Compound Leadscrew ........................................ 65
Cross Slide Leadscrew ....................................... 65
Leadscrew End Play Adjustment ...................... 66
Gib Adjustment .................................................. 66
Half Nut Adjustment ......................................... 67
Feedrod Clutch Adjustment .............................. 68
V-Belts ................................................................ 69
Brake & Switch .................................................. 69
Leadscrew Shear Pin Replacement .................. 71
Gap Removal & Installation.............................. 73
TROUBLESHOOTING .........................................74
WARRANTY & RETURNS ...................................77

16" South Bend Precision Toolroom Lathe (Circa 1958)

For Machines Mfg. Since 7/09
INTRODUCTION

INTRODUCTION

EVS Toolroom Lathes

About These Machines

Foreword

Features

"The screw cutting engine lathe is the oldest and
most important of machine tools and from it all
other machine tools have been developed. It was
the lathe that made possible the building of the
steamboat, the locomotive, the electric motor, the
automobile and all kinds of machinery used in
industry. Without the lathe our great industrial
progress of the last century would have been
impossible." —How To Run a Lathe, 15th
Edition, South Bend Lathe.

As the name implies, these lathes feature EVS
(Electronic Variable Speed) spindle control,
which allows the operator to quickly set the
exact spindle speed within the available range of
20–2500 RPM. Spindle speed is displayed on a
digital readout and controlled within each speed
range with the use of a dial—no changing gears
or looking up complex lever positions on a chart.

The lathes represented in this manual are a
modern day version of the screw cutting lathes
that trace their roots back to the 1700's, which
were themselves technological improvements of
the bow lathe that can be traced back thousands
of years to the ancient Egyptians.
Now, almost 300 years later, these modern
"screw cutting" lathes are not just a piece of
refined machinery, but a culmination of human
ingenuity and knowledge embodied into the
design and synergy of thousands of interworking
parts—some of which represent the life's work
and dreams of many inventors, mechanical
engineers, and world-class machinists—including
the likes of Leonardo da Vinci, Henry Maudsley,
and the founders of South Bend Lathe, John and
Miles O'Brien.
And now the torch is passed to you—to take
the oldest and most important type of machine
tool—and carry on the tradition. As the operator
of a South Bend Lathe, you now join the ranks
of some very famous and important customers,
such as Henry Ford, who used the machines he
purchased to help him change the world.

Capabilities
These EVS Toolroom Lathes are built for daily
use in a busy industrial setting. Loaded with
many nice features and high-precision parts,
these lathes excel at making fine tools, dies,
thread gauges, jigs, and precision test gauges—
however, they are by no means delicate. Thick
castings, heavy weight, and quality construction
throughout provide the necessary brawn for
demanding production and manufacturing tasks.

The beds of these lathes are constructed with
Meehanite castings that have been precision
hardened and ground in the traditional 3-V
prismatic design—long used on South Bend
Lathes for its accuracy, durability, and rigidity.
The headstock features quick-change gear levers
and an adjustable clutch mechanism for the feed
rod that can be set to prevent damage in the
event of a crash.
To further ensure a high degree of accuracy,
these lathes are equipped with NSK or NTN
spindle bearings. The spindles are the D1-6
camlock type with an MT#6 taper and 2.0625"
bore. The tailstock quills have an MT#4 taper
and offer 6" of travel.
The EVS lathes also include a pressurized
headstock oiling system that pre-lubricates
bearings/gears before the spindle starts and
delivers perfect lubrication during low speed
operations (compare to conventional splash
and bath oil systems that leave bearings/gears
starved for oil when the spindle is first started
and during low speed operations).
Finally, these EVS toolroom lathes are packed
with standard features, such as a complete
coolant system, easy-to-clean chip drawer, oneshot way lubrication system, included steady and
follow rests, adjustable work lamp, foot brake,
and powered cross feed.

-3-

INTRODUCTION

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Identiﬁcation
I

L
M

N
K
O
AB

AA
P

Z
X
Y

W
V

Figure 1. The 14" & 16" EVS Lathe.

Headstock
D1-6 Camlock MT#6 Spindle
Control Panel
Ball Bearing Style Steady Rest
4-Position Tool Holder
Follow Rest
Compound Slide
Compound Slide Handwheel
Work Lamp
Universal Cutting Fluid Tube and Nozzle
Cross Slide
Tailstock
Tailstock Handwheel
Thread Dial

O. Leadscrew Bearing Housing
P. Cutting Fluid Pump/Tank
Q. Spindle Rotation ON/OFF Lever
R. Half Nut Lever
S. Apron Oil Level Sight Glass
T. Quick Change Apron Feed Direction Knob
U. Manual Way Oil Pump
V. Brake Pedal
W. Feed Control Lever
X. Apron Handwheel
Y. Cross Slide Handwheel
Z. Removable Chip Drawer
AA. Micrometer Stop
AB. Quick Change Gearbox

Serious personal injury could occur if
you connect the machine to power before
completing the setup process. DO NOT
connect power until instructed to do so later
in this manual.

Untrained users have an increased risk
of seriously injuring themselves with this
machine. Do not operate this machine until
you have understood this entire manual and
received proper training.

A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.

-4-

For Machines Mfg. Since 7/09

SAFETY

EVS Toolroom Lathes

SAFETY

Understanding Risks of Machinery
Operating all machinery and machining equipment can be dangerous or relatively safe depending
on how it is installed and maintained, and the operator's experience, common sense, risk awareness,
working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).
The owner of this machinery or equipment is ultimately responsible for its safe use. This
responsibility includes proper installation in a safe environment, personnel training and usage
authorization, regular inspection and maintenance, manual availability and comprehension,
application of safety devices, integrity of cutting tools or accessories, and the usage of approved
personal protective equipment by all operators and bystanders.
The manufacturer of this machinery or equipment will not be held liable for injury or property
damage from negligence, improper training, machine modiﬁcations, or misuse. Failure to read,
understand, and follow the manual and safety labels may result in serious personal injury, including
amputation, broken bones, electrocution, or death.
The signals used in this manual to identify hazard levels are deﬁned as follows:
Death or catastrophic
harm WILL occur.

Moderate injury or ﬁre
MAY occur.

Death or catastrophic
harm COULD occur.

Machine or property
damage may occur.

Basic Machine Safety
1.

Owner’s Manual: All machinery and
machining equipment presents serious
injury hazards to untrained users. To
reduce the risk of injury, anyone who uses
THIS item MUST read and understand
this entire manual before starting.

Personal Protective Equipment: Operating
or servicing this item may expose the user
to ﬂying debris, dust, smoke, dangerous
chemicals, or loud noises. These hazards
can result in eye injury, blindness, longterm respiratory damage, poisoning,
cancer, reproductive harm or hearing loss.
Reduce your risks from these hazards
by wearing approved eye protection,
respirator, gloves, or hearing protection.

Trained/Supervised Operators Only:
Untrained users can seriously injure
themselves or bystanders. Only allow
trained and properly supervised personnel
to operate this item. Make sure safe
operation instructions are clearly
understood. If electrically powered, use
padlocks and master switches, and remove
start switch keys to prevent unauthorized
use or accidental starting.

Guards/Covers: Accidental contact with
moving parts during operation may cause
severe entanglement, impact, cutting,
or crushing injuries. Reduce this risk by
keeping any included guards/covers/doors
installed, fully functional, and positioned
for maximum protection.

-5-

EVS Toolroom Lathes

SAFETY

For Machines Mfg. Since 7/09

Entanglement: Loose clothing, gloves,
neckties, jewelry or long hair may
get caught in moving parts, causing
entanglement, amputation, crushing,
or strangulation. Reduce this risk by
removing/securing these items so they
cannot contact moving parts.

11. Chuck Keys or Adjusting Tools: Tools used
to adjust spindles, chucks, or any moving/
rotating parts will become dangerous
projectiles if left in place when the machine
is started. Reduce this risk by developing
the habit of always removing these tools
immediately after using them.

Mental Alertness: Operating this item
with reduced mental alertness increases
the risk of accidental injury. Do not let a
temporary influence or distraction lead to a
permanent disability! Never operate when
under the influence of drugs/alcohol, when
tired, or otherwise distracted.

12. Work Area: Clutter and dark shadows
increase the risks of accidental injury.
Only operate this item in a clean, nonglaring, and well-lighted work area.

Safe Environment: Operating electrically
powered equipment in a wet environment
may result in electrocution; operating near
highly ﬂammable materials may result in a
ﬁre or explosion. Only operate this item in
a dry location that is free from ﬂammable
materials.

Electrical Connection: With electically
powered equipment, improper connections
to the power source may result in
electrocution or fire. Always adhere to all
electrical requirements and applicable
codes when connecting to the power source.
Have all work inspected by a qualified
electrician to minimize risk.

Disconnect Power: Adjusting or servicing
electrically powered equipment while it
is connected to the power source greatly
increases the risk of injury from accidental
startup. Always disconnect power
BEFORE any service or adjustments,
including changing blades or other tooling.

10. Secure Workpiece/Tooling: Loose
workpieces, cutting tools, or rotating
spindles can become dangerous projectiles
if not secured or if they hit another object
during operation. Reduce the risk of this
hazard by verifying that all fastening
devices are properly secured and items
attached to spindles have enough clearance
to safely rotate.

-6-

13. Properly Functioning Equipment: Poorly
maintained, damaged, or malfunctioning
equipment has higher risks of causing
serious personal injury compared to
those that are properly maintained.
To reduce this risk, always maintain
this item to the highest standards and
promptly repair/service a damaged or
malfunctioning component. Always follow
the maintenance instructions included in
this documentation.
14. Unattended Operation: Electrically
powered equipment that is left unattended
while running cannot be controlled and is
dangerous to bystanders. Always turn the
power OFF before walking away.
15. Health Hazards: Certain cutting fluids
and lubricants, or dust/smoke created
when cutting, may contain chemicals
known to the State of California to cause
cancer, respiratory problems, birth defects,
or other reproductive harm. Minimize
exposure to these chemicals by wearing
approved personal protective equipment
and operating in a well ventilated area.
16. Difﬁcult Operations: Attempting
difficult operations with which you are
unfamiliar increases the risk of injury.
If you experience difficulties performing
the intended operation, STOP! Seek an
alternative method to accomplish the
same task, ask a qualified expert how the
operation should be performed, or contact
our Technical Support for assistance.

For Machines Mfg. Since 7/09

SAFETY

EVS Toolroom Lathes

Additional Metal Lathe Safety
1.

Clearing Chips. Metal chips can easily cut
bare skin—even through a piece of cloth.
Avoid clearing chips by hand or with a rag.
Use a brush or vacuum to clear metal chips.

Chuck Key Safety. A chuck key left in the
chuck can become a deadly projectile when
the spindle is started. Always remove the
chuck key after using it. Develop a habit of
not taking your hand off of a chuck key unless
it is away from the machine.

Tool Selection. Cutting with an incorrect
or dull tool increases the risk of accidental
injury because extra force is required for the
operation, which increases risk of breaking
or dislodging components, which can cause
small shards of metal to become dangerous
projectiles. Always select the right cutter for
the job and make sure it is sharp. A correct,
sharp tool decreases strain and provides a
better finish.

Securing Workpiece. An improperly secured
workpiece can fly off of the lathe spindle with
deadly force, which can result in a severe
impact injury. Make sure the workpiece is
properly secured in the chuck or faceplate
before starting the lathe.

Large Chucks. Large chucks are very heavy
and difficult to grasp, which can lead to
crushed fingers or hands if mishandled. Get
assistance when installing or removing large
chucks to reduce this risk. Protect your hands
and the precision-ground ways by using a
chuck cradle or piece of plywood over the
ways of the lathe when servicing chucks.

Safe Clearances. Workpieces that crash into
other components on the lathe may throw
dangerous projectiles in all directions, leading to impact injury and damaged equipment.
Before starting the spindle, make sure the
workpiece has adequate clearance by handrotating it through its entire range of motion.
Also, check the tool and tool post clearance,
chuck clearance, and saddle clearance.

Speed Rates. Operating the lathe at the
wrong speed can cause nearby parts to break
or the workpiece to come loose, which will
result in dangerous projectiles that could
cause severe impact injury. Large workpieces
must be turned at slow speeds. Always use
the appropriate feed and speed rates.

Stopping Spindle by Hand. Stopping the spindle by putting your hand on the workpiece or
chuck creates an extreme risk of entanglement, impact, crushing, friction, or cutting
hazards. Never attempt to slow or stop the
lathe spindle with your hand. Allow the
spindle to come to a stop on its own or use the
brake (if equipped).

Crashes. Driving the cutting tool or other
lathe components into the chuck may cause
an explosion of metal fragments, which can
result in severe impact injuries and major
damage to the lathe. Reduce this risk by
releasing automatic feeds after use, not leaving lathe unattended, and checking clearances before starting the lathe. Make sure no
part of the tool, tool holder, compound slide,
cross slide, or carriage will contact the chuck
during operation.

10. Long Stock Safety. Long stock can whip violently if not properly supported, causing serious impact injury and damage to the lathe.
Reduce this risk by supporting any stock that
extends from the chuck/headstock more than
three times its own diameter. Always turn
long stock at slow speeds.
11. Coolant Safety. Contaminated cutting fluid
is a very poisonous biohazard that can cause
personal injury from skin contact alone.
Incorrectly positioned cutting fluid nozzles
can splash on the operator or the floor,
resulting in an exposure or slipping hazard.
To decrease your risk, change cutting fluid
regularly and position the cutting fluid nozzle
where it will not splash or end up on the
floor.

-7-

EVS Toolroom Lathes

P R E PA R AT I O N

For Machines Mfg. Since 7/09

PREPARATION

Preparation Overview Things You'll Need
The purpose of the preparation section is to help
you prepare your machine for operation. The
list below outlines the basic process to follow to
prepare the lathe for operation. Specific steps for
each of these points will be covered in detail later
in this section.

The typical preparation process is as follows:
1.

Unpack the lathe and inventory the contents
of the box/crate.

Clean the lathe and its components.

Identify an acceptable location for the lathe
and move it to that location.

Level the lathe and either bolt it to the floor
or place it on mounts.

Assemble the loose components and make
any necessary adjustments or inspections to
ensure the lathe is ready for operation.

Connect the lathe to the power source.

Test run the lathe to make sure it functions
properly and is ready for operation.

To complete the preparation process, you will
need the following items:
For Lifting and Moving
s ! &ORKLIFT OR /THER 0OWER ,IFTING $EVICE
(rated for at least 5000 lbs).
s ,IFTING 3TRAP or Chain with Hook
(rated for at least 5000 lbs.)
s Helper for moving machine.
s Two 12" 2x6's
s 0RECISION ,EVEL
For Power Connection
s ! QUALIFIED ELECTRICIAN TO ENSURE A SAFE AND
code-compliant connection to the power
source. (Refer to Page 15 for details.)
For Assembly
s Cotton Rags
s Mineral Spirits
s Quality Metal Protectant Oil
s 3AFETY 'LASSES
s Wrench or Socket 21mm
s Wrench or Socket 19mm
s &LOOR -OUNTING (ARDWARE as Needed
s Standard Screwdriver #2

Unpacking
This item was carefully packaged to prevent
damage during transport. If you discover any
damage, please immediately call Customer
Service at (360) 734-1540 for advice. You may
need to file a freight claim, so save the containers
and all packing materials for possible inspection
by the carrier or its agent.

-8-

For Machines Mfg. Since 7/09

P R E PA R AT I O N

EVS Toolroom Lathes

Inventory
Main Inventory 1: (Figure 2)
A.
B.
C.
D.
E.
F.

Steady Rest Assembly.................................... 1
12" Faceplate w/D1-6 Camlock Stud Set ...... 1
10" Four-Jaw Chuck w/Combo Jaws ............. 1
Four-Jaw Chuck Key ..................................... 1
Four-Jaw Chuck D1-6 Camlock Stud Set ..... 1
Follow Rest Assembly .................................... 1

Tool Box Inventory: (Figure 3)
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.

Qty

Tool Box .......................................................... 1
Three-Jaw Chuck Key ................................... 1
Tool Post T-Wrench........................................ 1
Hex Wrench Set 1.5-10mm ............................ 1
Dead Center MT#4......................................... 1
Carbide-Tipped Dead Center MT#4 .............. 1
Tapered Spindle Sleeve MT#6-#4 ................. 1
Open End Wrench 22/24mm ......................... 1
Open End Wrench 14/17mm ......................... 1
Open End Wrench 10/12mm ......................... 1
Phillips Screwdriver #2 ................................. 1
Standard Screwdriver #2 ............................... 1
9"-Chuck Jaws (SB1014-15, SB1037-38) ...... 3
8"-Chuck Jaws (SB1012-13) .......................... 3
Cast Iron Leveling Pads ................................ 8
Handwheel Handles....................................... 2

Note: Some inventory components may be
shipped inside of the lathe electrical box. These
items MUST be removed before connecting the
lathe to the power source.

Figure 2. Main inventory.

N
M
K

O
Q

R
S

H
U
T

I
J

Figure 3. Toolbox inventory.

-9-

EVS Toolroom Lathes

P R E PA R AT I O N

For Machines Mfg. Since 7/09

Cleaning & Protecting
The unpainted surfaces are coated at the factory
with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
The beneﬁt of this rust preventative is that it
works very well. The downside is that it can be
time-consuming to thoroughly remove.
Be patient and do a careful job when cleaning
and removing the rust preventative. The time
you spend doing this will reward you with
smooth-sliding parts and a better appreciation
for the proper care of the unpainted surfaces.
Although there are many ways to successfully
remove the rust preventative, we have cleaned
thousands of machines and found the following
process to be the best balance between efﬁciency
and minimized exposure to toxic fumes or
chemicals.

Many cleaning solvents are
toxic if inhaled. Minimize
your risk by only using
these products in a well
ventilated area.

Avoid chlorine-based solvents, such as
acetone or brake parts cleaner that may
damage painted surfaces. Always follow the
manufacturer’s instructions when using any
type of cleaning product.

Basic steps for removing rust preventative:
1.

Put on safety glasses and disposable gloves.

#OAT ALL SURFACES THAT HAVE RUST PREVENTATIVE
with a liberal amount of your cleaner or
degreaser and let them soak for a few
minutes.

Wipe off the surfaces. If your cleaner or
degreaser is effective, the rust preventative
will wipe off easily.

Before cleaning, gather the following:
s
s

$ISPOSABLE rags
#LEANERDEGREASER (certain citrus-based
degreasers work extremely well and they
have non-toxic fumes)
3AFETY GLASSES DISPOSABLE GLOVES

Note: Automotive degreasers, mineral spirits, or
7$s CAN BE USED TO REMOVE RUST PREVENTATIVE
Before using these products, though, test them
on an inconspicuous area of a painted area to
make sure they will not damage it.

Note: To clean off thick coats of rust preventative
on ﬂat surfaces, such as beds or tables, use
A 0,!34)# PAINT SCRAPER TO SCRAPE OFF THE
majority of the coating before wiping it off
WITH YOUR RAG $O NOT USE A METAL SCRAPER OR
it may scratch the surface.)
4.

-10-

Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used for
cleaning. Avoid using these
products to remove rust
preventative.

Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a
quality metal protectant or light oil to
prevent rust.

For Machines Mfg. Since 7/09

P R E PA R AT I O N

EVS Toolroom Lathes

Weight Load

Location

Refer to the Machine Speciﬁcations for the
weight of your machine. Make sure that the
surface upon which the machine is placed will
bear the weight of the machine, additional
equipment that may be installed on the machine,
and the heaviest workpiece that will be used.
Additionally, consider the weight of the operator
and any dynamic loading that may occur when
operating the machine.

Physical Environment
The physical environment where your machine
Physical
Environment
is operated is important for safe operation and
Electrical
Installation
longevity
of parts.
For best results, operate this
machine
in a dry environment that is free from
Lighting
excessive moisture, hazardous or flammable
Weight
chemicals, Load
airborne abrasives, or extreme
Space Allocation
conditions.
Extreme conditions for this type
of machinery are generally those where the
ambient temperature is outside the range of 41°–
104°F; the relative humidity is outside the range
of 20–95% (non-condensing); or the environment
is subject to vibration, shocks, or bumps.

Electrical Installation
Place this machine near an existing power
source. Make sure all power cords are protected
from traffic, material handling, moisture,
chemicals, or other hazards. Make sure to leave
access to a means of disconnecting the power
source or engaging a lockout/tagout device.

Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation
of auxiliary equipment. With permanent
installations, leave enough space around
the machine to open or remove doors/covers
as required by the maintenance and service
described in this manual.

Children or untrained
people may be seriously
injured by this machine.
Only install in an access
restricted location.

Lighting
Lighting around the machine must be adequate
enough that operations can be performed
safely. Shadows, glare, or strobe effects that
may distract or impede the operator must be
eliminated.

Wall

Min. 30"

SB1037-38

Keep
Workpiece
Loading Area
Unobstructed

SB1014-15

Electrical
Access
Door

SB1012-13

90"

109"

90"

60"

112"

130"

112"

= Power Connection Location

B
Lathe

D 20 ⁄2" 20 ⁄2" 201⁄2"
1

A
Figure 4. Space required for full range of movement.

-11-

EVS Toolroom Lathes

P R E PA R AT I O N

Lifting & Moving

This machine and its
parts are heavy! Serious
personal injury may occur
if safe moving methods are
not used. To reduce the
risk of a lifting or dropping
injury, ask others for help
and use power equipment.

To further balance the load, loosen the
carriage lock bolt (see Figure 6), disengage
the half nut lever, put the feed control lever
in neutral, then use the carriage handwheel
to move the carriage next to the tailstock.
Lock Bolt
Carriage
Handwheel

Do not attempt to lift or move this lathe if you do
not have the proper equipment or the necessary
assistance from other people. All lifting
equipment must be rated to at least 5,000 lbs.
to account for dynamic loads from bouncing or
pulling that may be applied while lifting. Refer
to the Things You'll Need section on Page 8 for
details.

Prepare the permanent location for the
lathe.

Half Nut Lever

Feed Control Lever

Disengaged

Cross Slide
Neutral
Carriage

HALF NUT
LEVER

FEED CONTROL
LEVER

To lift and move your lathe:
1.

For Machines Mfg. Since 7/09

Engaged

Figure 6. Carriage controls set for moving the carriage.

Remove the shipping crate top and sides,
then remove the small components from the
shipping pallet.

To balance the lifting load, loosen the
tailstock lock lever (Figure 5), move the
tailstock to the end of the bedway, then lock
it in place.

Note: The 2x6's extend the lifting straps away
from the bottom of the bed to prevent
machine damage from excessive strap
pressure against the leadscrew, feed rod, and
spindle control rod. Make sure to use them.

Tailstock Lock Lever

Position a 12" long 2x6 board under each end
of the bed, as shown in Figure 7, wrap the
lifting straps around the bottom of the 2x6's.

(Cross-Section View of Lifting Setup)
To Forklift or Lifting Hook
Lifting
Strap

Lathe
Bed
12" Long
2x6 Board

Leadscrew

Feed Rod
Spindle
Control
Rod

Figure 5. Tailstock lock lever.
Figure 7. Cross section of lifting setup to keep strap
from putting pressure against leadscrew or rods.

-12-

For Machines Mfg. Since 7/09
6.

P R E PA R AT I O N

Attach the lifting straps to forklift forks or a
hook and chain, as shown in Figures 8–9.
Forklift
Forks
Lifting
Straps

EVS Toolroom Lathes

Leveling & Mounting
You must level your machine and either use the
included foot pads and leveling hardware or bolt
your lathe to the floor. Because mounting your
lathe to the floor with permanent hardware is an
optional step and floor materials may vary, floor
mounting hardware is not included.

Leveling

12" Long
2x6 Board

Figure 8. Lathe set up for lifting with forklift.

For accurate turning results and to prevent
warping the cast iron bed and ways, the lathe
bedways MUST be leveled from side-to-side
and from front-to-back.
Re-check the bedways 24 hours after
installation, two weeks after that, and then
annually to make sure they remain level.

Lifting Hook
with Chain
Lifting
Straps

Leveling machinery helps precision components,
such as bedways, remain straight and ﬂat during
the lifespan of the machine. Components on an
unleveled machine may slowly twist due to the
dynamic loads placed on the machine during
operation.
12" Long
2x6 Board

12" Long
2x6 Board

Figure 9. Lathe set up for lifting with hook and chain.

Unbolt the lathe from the shipping pallet,
then with an assistant to help keep the lathe
from swaying, raise the lathe a couple of
inches.

For best results, use a precision level that
is at least 12" long and sensitive enough to
show a distinct movement when a 0.003" shim
(approximately the thickness of one sheet of
standard newspaper) is placed under one end of
the level.
See the ﬁgure below for an example of a high
precision level.

— If the load is not well balanced, or you
see any other difﬁculties with the lifting
equipment, immediately lower the lathe
to the pallet again. Resolve any lifting or
balancing issues, then repeat this step.
8.

With assistance to steady the load, move it to
the prepared location and lower it in place.

Figure 10. Example of a precision level.

-13-

P R E PA R AT I O N

EVS Toolroom Lathes

To level the machine, use a precision level to
make sure the bedways are level from side-toside and from front-to-back.
— If using the included leveling pads
(Figure 11), place them under the six
leveling stud locations, then adjust the
studs to level the lathe.

For Machines Mfg. Since 7/09

Assembly
With the exception of the handwheel handles, the
lathe is shipped fully assembled.
To install the handwheel handles, thread the
large handle into the carriage handwheel and the
small handle into the cross slide handwheel, as
shown in Figure 13.

Studs

Pads

Figure 11. Leveling pads and screws.

— If using mounting hardware that does not
allow for adjustment, level the lathe by
placing metal shims between the lathe
base and the ﬂoor before bolting down.

Bolting to Concrete Floors
Lag screws and anchors, or anchor studs
(below), are two popular methods for securing
machinery to a concrete ﬂoor. We suggest you
research the many options and methods for
securing your machine and choose the best one
for your speciﬁc application.
Anchor
Stud

Handwheel
Handles

Figure 13. Handwheel handles installed.

Lubricating Lathe
GEARBOXES MUST
BE FILLED WITH OIL!

NO OIL SHIPPED WITH
MACHINE!
Refer to the Lubrication
Section in this Manual
for Recommended
Oil Type.

Lag Screw
and Anchor

Figure 12. Common types of fasteners for bolting
machinery to concrete floors.

Most electrical codes require that machines
connected to the power source by fixed
conduit MUST be secured to the floor.
-14-

The headstock, gearbox, and apron oil reservoirs
must have the proper amount of oil in them
before the lathe can be operated for the ﬁrst
time.
Running the lathe without oil in a gearbox is
considered unwarrantable abuse, which may
result in damage to the bearings and gears. Refer
to the Lubrication section, beginning on Page
56, for details on how to check and add oil.

For Machines Mfg. Since 7/09

P R E PA R AT I O N

In addition to the gearboxes, we also recommend
that you lubricate all other points on the
machine at this time. This can be accomplished
by following the maintenance schedule on Page
54.
Note: If your lathe was shipped with oil in the
gearboxes, do not change that oil until after the
break-in period.

Adding Cutting Fluid
Add the cutting fluid of your choice now. For
detailed instructions on where the cutting fluid
tank is located and how to add fluid, refer to
Cutting Fluid System on Page 62.

Power Connection
Electrocution or fire
may occur if machine is
ungrounded, incorrectly
connected to power, or
connected to an undersized
circuit. Use a qualified
electrician to ensure a safe
power connection.
Once all preparation steps previously described
in this manual have been completed, the
machine can be connected to the power source.
In order to be connected to the power source, a
circuit must be installed/prepared that meets
the requirements of the lathe, and a power
connection method must be established for that
circuit. The following lists show the minimum
requirements for each model, and instructions
follow for each connection method.
Note About Power Cords: Using an incorrectly
sized cord causes electrical components on
the machine and the cord to become very hot,
which will greatly decrease the life of electrical
components or result in fire. For best results,
use the shortest length of cord possible for your
machine, and never use a smaller cord gauge
than the specified minimum.

EVS Toolroom Lathes

This machine is equipped with a frequency
drive that contains sensitive electronics,
which can be damaged by a phase converter.
DO NOT use a phase converter to power this
machine. Doing so will void the warranty.

SB1012 (220V 3-Phase)
Full Load Amp Draw ............................ 15.7 Amps
Phase ..........................................................3-Phase
Frequency ...................................................... 60 Hz
Minimum Circuit Size ............................. 20 Amps
Recommended Plug/Receptacle ......NEMA L15-20
Minimum Cord Size .......... 12 AWG, 4-Wire, 300V
Maximum Cord Length ................................. 50 ft.

SB1014, SB1037 (220V 3-Phase)
Full Load Amp Draw ............................ 21.7 Amps
Phase ..........................................................3-Phase
Frequency ...................................................... 60 Hz
Minimum Circuit Size ............................. 30 Amps
Recommended Plug/Receptacle ......NEMA L15-30
Minimum Cord Size ............ 8 AWG, 4-Wire, 300V
Maximum Cord Length ................................. 50 ft.

SB1013 (440V 3-Phase)
Full Load Amp Draw ............................ 7.75 Amps
Phase ..........................................................3-Phase
Frequency ...................................................... 60 Hz
Minimum Circuit Size ............................. 15 Amps
Recommended Power Connection ........ Hardwire*

SB1015, SB1038 (440V 3-Phase)
Full Load Amp Draw .......................... 10.75 Amps
Phase ..........................................................3-Phase
Frequency ...................................................... 60 Hz
Minimum Circuit Size ............................. 15 Amps
Recommended Power Connection ........ Hardwire*
* Hardwire setups must include a locking
disconnect switch between the power source and
the lathe. Refer to Page 16 for more details.

-15-

EVS Toolroom Lathes

P R E PA R AT I O N

Connecting Power Cord to Lathe

For Machines Mfg. Since 7/09

To Power Source
Wtt

Rd
B
Bk
L1

Electrocution or death will occur if you
attempt this procedure with the power cord
connected to the power source. The cord
must be disconnected from power before
performing this procedure.
These instructions are for setups where the lathe
will be connected to the power source with a
power cord and plug, as opposed to a hardwire
setup.

Incoming
Power
Strain
Relief

Main
Power
Switch

Figure 14. Location to connect power inside main
electrical cabinet.

Thread the power cord through the strain
relief, and up to the main power switch
shown in Figure 14.

Connect the incoming L1, L2, L3 and ground
wires to the main power switch terminals, as
illustrated in Figure 15.

Gn
Gn

Ground

Power
Connection
Terminals

Figure 15. Power connection at main power switch.

To connect power cord to the lathe:
Unlock and open the main electrical cabinet
door, and install a strain relief in the
location shown in Figure 14.

MASTER
POWER SWITCH

4.
1.

Make sure the cord/wires have loose slack
between the strain relief and terminal
connections, then tighten the strain relief to
secure the power cord.

Note: The strain relief must be tightened against
the outermost jacket of the cord. Avoid overtightening the strain relief or it may crush
the cord and cause a short.
5.

Test the strain relief to ensure it is properly
tightened by pulling the cord from outside
the box with light-to-moderate force. When
the strain relief is properly tightened, the
cord will not slide.

Close and lock the main electrical box door.

Hardwiring Lathe to Power
Source
Hardwire setups require power supply lines to
be enclosed inside of conduit, which is securely
mounted and constructed in adherence to
applicable electrical codes.
A hardwire setup for this machine must be
equipped with a locking disconnect switch
as a means to disconnect the power during
adjustments or maintenance, which is a typical
requirement for lock-out/tag-out safety programs
(commonly required by OSHA).
Figure 16 shows a simple diagram of a hardwire
setup with a locking disconnect switch between
the power source and the machine.

-16-

P R E PA R AT I O N

For Machines Mfg. Since 7/09

Power Source

Locking
Disconnect Switch

Conduit

Test Run
Machine

After all preparation steps have been completed,
the machine and its safety features must be
tested to ensure correct operation. If you discover
a problem with the operation of the machine or
its safety components, shut the machine down,
disconnect it from power, and do not operate it
again until you have resolved the problem.

Conduit

Figure 16. Typical hardwire setup with a locking
disconnect switch.

Due to the complexity required for planning,
bending, and installing the conduit necessary for
a hardwire setup, this type of setup can only be
performed by an experienced electrician.
For Electrician: Connect the incoming power
wires as shown in Figure 15.

Correcting Out-of-Phase Wiring
This sub-section is only provided for
troubleshooting. If you discover during the test
run that the lathe will not operate, or that the
spindle runs backwards, the lathe may be wired
out of phase. Without the proper test equipment
to determine the phase of power source legs,
wiring machinery to 3-phase power may require
trial-and-error. Correcting this is simply a
matter of reversing the positions where two of
the incoming power source wires are connected.

Note: The variable speed on this machine is
controlled by a frequency drive unit constructed
with sensitive electronics. These electronics
can be damaged if power is disconnected during
operation. Therefore, unless the stop button and
brake lose functionality, always properly shut
the machine down before disconnecting it from
the power source.
A Troubleshooting section is provided, starting
on Page 74, to assist you with solutions if a
problem occurs or if the lathe does not function
as described in this section.
If you need additional help after reviewing the
troubleshooting section, or you are not confident
troubleshooting the machine on your own,
contact our tech support at (360) 734-1540.
To test run your machine:
1.

Read and follow the safety instructions at
the beginning of the manual, take required
safety precautions, and make sure all
previous preparation steps discussed in this
manual have been followed and completed.

Clear away all tools and objects used during
assembly, lubrication, and preparation.

DISCONNECT LATHE FROM POWER!

Make sure that the chuck and jaws, if
installed, are secure (refer to Chuck and
Faceplate Mounting on Page 27).

To correct wiring that is out of phase:
1.

EVS Toolroom Lathes

Push the stop button, turn the main power
switch to OFF, and disconnect the machine
from power (or shut OFF and lock out the
power source if hardwired).

Open the electrical box and disconnect the
L1 and L2 wires shown in Figure 15 on the
"To Power Source" side of the switch.

Connect the L1 wire to the terminal where
the L2 wire was connected originally.

Connect the L2 wire to the terminal where
the L1 wire was connected originally.

Close and latch the electrical box, and
reconnect the machine to the power source.

Note: If a chuck is not installed on the lathe, you
do not need to install one for this test.
5.

Turn the pump switch (Figure 17) to the
OFF position, and point the fluid nozzle into
the chip drawer.

-17-

P R E PA R AT I O N

EVS Toolroom Lathes

9.
Stop Button

For Machines Mfg. Since 7/09

Move the feed direction forward/reverse lever
to the middle (neutral) position, as shown in
Figure 20.

Pump Switch

FORWARD
NEUTRAL
REVERSE

Figure 17. Control panel-test run.

Turn the spindle speed dial (Figure 18) all
the way counterclockwise (lowest speed) to
avoid possibility of a high-speed start.

Spindle Speed Dial

Low
20-400 RPM

Figure 20. Feed direction forward/reverse lever in the
neutral position.

10. Disengage the half nut lever, put the feed
control lever in neutral, and make sure the
carriage lock bolt is loose (see Figure 6).
High
400-2500 RPM

This step will allow the carriage to move
freely when the handwheel is rotated and
make sure that the carriage will not move
when the lathe is started.
Carriage Lock Bolt

Figure 18. Spindle speed controls.

Move the spindle speed range lever (Figure
18) to the left so the headstock is set in the
low range (20-400 RPM). (You may need to
slightly rotate the chuck by hand to engage
the lever.)

Move the gearbox range lever to the middle
(neutral) position, as shown in Figure 19.
LOW
Neutral

Half Nut Lever

Feed Control Lever

Cross Slide
Neutral
Carriage

HIGH
FEED CONTROL
LEVER

Disengaged
HALF NUT
LEVER
Engaged

Figure 21. Controls used to disengage carriage so that
it will move freely when the handwheel is turned.

Figure 19. Gearbox range lever in middle position.

-18-

For Machines Mfg. Since 7/09

P R E PA R AT I O N

11. Move the spindle ON/OFF lever to the OFF
(center) position, as shown in Figure 22.

Spindle ON/OFF
Lever
Figure 22. Spindle ON/OFF lever-setup.

12. Connect the lathe to power source, then turn
the main power switch (Figure 23) to the
ON position.

EVS Toolroom Lathes

Note: This headstock has a pressurized oil
system that is equipped with an oil pressure
safety switch. If oil stops flowing or does not
flow to start with, the lathe will not operate
until the oil is properly flowing. Refer to
Troubleshooting to correct.

Never bypass the oil pressure safety switch!
If you do, you will void the warranty, and
headstock damage may occur.
14. Make sure that all bystanders are out of the
way, tools are cleared away, and the chuck
key is removed from the chuck.
15. Move the spindle ON/OFF lever (Figure
25) down and the chuck will rotate counterclockwise (down and toward you, as you face
the front of the lathe).

Main
Power
Switch
Spindle ON/
OFF Lever
Figure 23. Main power switch in ON position.

13. Rotate the stop button (Figure 17 on Page
18) clockwise until it pops out. The pump
will turn ON. Observe the oil pump tube
sight glass (Figure 24). Verify that you see
oil ﬂowing out of the tube and against the
sight glass.

Oil Pump Sight
Glass and Oil Tube

Figure 25. Spindle Lever in ON position.

16. Observe the lathe and listen for any
abnormal noises or vibration. The lathe
should run smoothly with little or no
vibration or rubbing noises.
17. Push the stop button. The lathe should stop.

Figure 24. Oil pump sight glass and oil tube.

-19-

EVS Toolroom Lathes

P R E PA R AT I O N

18. Move the spindle ON/OFF lever up to the
OFF position, reset the stop button by
twisting it clockwise until it pops out, then
restart the spindle with the lever.
19. Push the foot brake. The lathe should come
to a quick stop.
— If the brake pedal has no effect on the
lathe, push the stop button, and refer to
V-Belts and Brake & Switch on Page
69 to make any required adjustments.
20. Remove the lathe headstock side cover. The
kill switch mounted to the headstock should
prevent the lathe from starting while this
cover is removed.
21. Stand away from all the exposed gears on
the side of the headstock, and attempt to
start the lathe.
— If the lathe starts, the safety switch is not
functioning properly and may need to be
replaced before the machine can be safely
operated.

-20-

For Machines Mfg. Since 7/09

22. Replace the headstock side cover, then start
the lathe again.
Note: The lathe will not start if the headstock
side cover is not properly installed.
23. Turn the cutting fluid pump ON, and open
the valve. Verify that fluid flows from the
nozzle, then turn the cutting fluid pump
OFF.
The test run is now finished. Shut the lathe down
and begin the Spindle Break-In procedure.

P R E PA R AT I O N

For Machines Mfg. Since 7/09

Spindle Break-In
It is essential to closely follow the proper break-in
procedures to ensure trouble-free performance.
Complete this process once you have familiarized
yourself with all instructions in this manual and
completed the test run.

EVS Toolroom Lathes

Move the feed direction forward/reverse lever
(Figure 28) to the neutral position.
FORWARD
NEUTRAL
REVERSE

To complete the spindle break-in:
1.

Successfully complete the Test Run
procedure beginning on Page 17.

Move the gearbox range lever to low range
position, as shown in Figure 26.

Figure 28. Feed direction lever in neutral position.

LOW
Neutral
HIGH

Do not leave the lathe unattended during the
break-in period. Make sure that you keep a
close eye on the headstock oil thermometer
(Figure 29) on the oil reservoir. If the
headstock oil temperature reaches 160°F,
shut the lathe down and let the system cool
before resuming break-in.

Figure 26. Gearbox range lever-break in.

Turn the spindle speed dial (Figure 27) all
the way counterclockwise to the minimum
speed, and move the spindle speed range
lever to the low range.

Spindle Speed Dial

Low
20-400 RPM

Spindle Speed
Lever

High
400-2500 RPM

Figure 29. Oil temperature thermometer.

Figure 27. Spindle speed controls.

-21-

P R E PA R AT I O N

EVS Toolroom Lathes

Disengage the half nut and the feed control
levers shown in Figures 30–31.

Feed Control Lever Disengaged
(Neutral Position)

Half Nut Lever
Disengaged (Up)
Figure 30. Power fed and half nut levers disengaged.

Cross Slide
Neutral
Carriage
FEED CONTROL
LEVER

After completing the previous step, stop the
spindle and move the gearbox range lever to
neutral, then move the spindle speed range
lever to high.

Turn the lathe ON and let it run for ten
minutes in each speed of 400, 1000, and 2500
RPM.

After completing Step 8, reduce the spindle
speed to 400 RPM and let the lathe run for a
final 15 minutes as a cool-down.

10. Turn the lathe OFF.
11. Change the oil in all of the reservoirs,
tighten the V-belts, and perform all
other lubrication steps mentioned in the
Maintenance section of this manual.

Disengaged
HALF NUT
LEVER
Engaged

Figure 31. Feed control lever and half nut in
disengaged positions.

For Machines Mfg. Since 7/09

Turn the lathe ON, and let it run for ten
minutes in each speed of 20, 200, and 400
RPM, using the spindle speed dial (Figure
32) to adjust the speed.

Recommended
Adjustments
For your convenience, the adjustments listed
below have been performed at the factory.
However, because of the many variables involved
with shipping, we recommend that you at least
verify the following adjustments to ensure the
best possible results from your new machine.
Step-by-step instructions for these adjustments
can be found on the pages referenced below.

Spindle Speed Dial

Factory adjustments that should be veriﬁed:
Low
20-400 RPM

High
400-2500 RPM

Figure 32. Spindle speed controls.

-22-

4AILSTOCK ALIGNMENT Page 34).

#OMPOUND AND CROSS SLIDE BACKLASH
adjustment (Page 65).

'IB ADJUSTMENTS Page 66).

After the first 16 hours of use, the V-belts will
stretch and seat into the pulley grooves. The
V-belts must be properly re-tensioned after
this period to avoid reducing their useful life.
Refer to the V-Belts section on Page 69 for
detailed instructions.

For Machines Mfg. Since 7/09

O P E R AT I O N

EVS Toolroom Lathes

OPERATION

Operation Overview

To complete a typical operation, the operator
does the following:

The purpose of this overview is to provide
the novice machine operator with a basic
understanding of how the machine is used during
operation, so they can more easily understand
the controls discussed later in this manual.

Puts on safety glasses, rolls up sleeves,
removes jewelry, and secures any clothing,
jewelry, or hair that could get entangled in
moving parts.

Examines the workpiece to make sure it
is suitable for turning, then mounts the
workpiece in one of the chucks or on the
faceplate, and removes the chuck key from
the chuck.

Mounts the tooling, aligns it with the
workpiece, then backs it away to establish a
safe startup clearance.

Clears all tools from the lathe.

Sets the correct spindle speed range for the
operation, and turns the spindle speed dial
all the way counterclockwise (to the lowest
speed) to avoid the possibility of damage
from a high speed start.

Checks for safe clearances by rotating
the workpiece by hand at least one full
revolution.

Moves slides to where they will be used
during operation.

If using power feed, selects the proper feed
rate for the operation.

Turns the main power switch ON, resets
the stop button so it pops out, then moves
the spindle ON/OFF lever down to start
spindle rotation. The spindle will rotate
counterclockwise (down and toward the
operator when facing the front of the lathe).

Note: Due to the generic nature of this overview,
it is not intended to be an instructional guide
for performing actual machine operations.
To learn more about speciﬁc operations and
machining techniques, seek training from people
experienced with this type of machine, and do
additional research outside of this manual by
reading "how-to" books, trade magazines, or
websites.

To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.

Loose hair, clothing, or
jewelry could get caught
in machinery and cause
serious injury or death.
Keep these items away
from moving parts at all
times to reduce this risk.

During operation, small
metal chips may become
airborne, leading to serious
eye injury. Wear safety
glasses to reduce this risk.

10. Turns the spindle speed dial clockwise to the
desired RPM.
11. Uses the carriage handwheels or power
feed options to move the tooling into the
workpiece for operations.
12. When finished cutting, moves the ON/OFF
lever to the center position to turn the lathe
OFF, then removes the workpiece.

-23-

O P E R AT I O N

EVS Toolroom Lathes

Description of Controls
& Components
Refer to the following figures and descriptions
to become familiar with the basic controls of this
machine.

Main Power Switch

Change Gear Chart: Displays the positions of
the various gears for different threading or
turning options.

Spindle Speed Range Lever: Shifts the
headstock into low or high range for spindle
speeds between 20–400 RPM or 400–2500
RPM.

Thread and Feed Chart: Shows the
configurations of the gearbox levers to
achieve a particular feed rate.

Gearbox Levers: Move the gearbox gears
into particular ratios, which then turn the
leadscrew and feed rod for threading and
power feed operations.

Feed Direction Lever: Shifts the direction
that the gearbox is turning, which changes
the direction of the leadscrew and feed rod.

Gearbox Range Lever: Shifts the gearbox
between high, neutral, or low range and has
no effect on spindle RPM.

The main power switch is shown in Figure 33. It
turns master power ON/OFF to the lathe.

Main
Power
Switch

Figure 33. Main power switch.

For Machines Mfg. Since 7/09

Carriage Controls

Headstock Controls

H
G

B
I
C

J
K

T
E

L
D

Q
M
P
D
Figure 34. Headstock controls.

-24-

Figure 35. Carriage controls.

G. 4-Position Tool Post Lever: Locks the rotary
tool post in four possible detents.

For Machines Mfg. Since 7/09

O P E R AT I O N

Cutting Fluid Flow Control Lever: Controls
the flow of cutting fluid from the nozzle.

Compound Slide Handwheel: Moves the
compound slide forward or backward.
Includes an indirect-read graduated scale
(distance represents actual tool movement—
not amount of material removed).

Carriage Lock Bolt: Secures the carriage in
place for greater rigidity and accuracy when
using the cross or compound slide for the
machining operation.

Thread Dial: Indicates when to engage the
half nut during threading operations.

Thread Dial Chart: Indicates on which thread
dial reading to engage the half nut for
specific inch or Whitworth thread pitches.

EVS Toolroom Lathes

Control Panel
U

Figure 36. Control panel.

M. Spindle ON/OFF Lever: Starts, stops and
reverses direction of spindle rotation.
N.

Half Nut Lever: Engages and disengages the
half nut for threading operations.

O. Apron: Houses the carriage gearing and
internal components.
P.

Quick Change Feed Direction Knob: Changes
apron feed direction without having to stop
the lathe and move the headstock feed
direction lever.

Tachometer Display: Displays the current
spindle speed in RPM.

Spindle Speed Dial: Changes the spindle
speed within the set speed range.

W. Power Light: Illuminates when lathe is
receiving power.
X.

Cutting Fluid Pump Switch: Start/stops the
cutting fluid pump motor.

Jog Button: Turns the spindle motor ON
while being pressed and held.

Emergency Stop Button: Stops all machine
functions. Twist clockwise to reset.

Q. Feed Control Lever: Engages and disengages
the cross feed and carriage feed gearing.
R.

Manual Carriage Oil Pump: Draws oil from
the apron case and lubricates the carriage
and ways through various oil ports.

Cross Slide Handwheel: Moves the cross
slide toward or away from the workpiece.
Includes an direct-read graduated scale
(distance represents amount of material
removed from diameter of workpiece).

Carriage Handwheel: Moves the carriage
from side-to-side along the bed.

-25-

O P E R AT I O N

EVS Toolroom Lathes

Tailstock Controls
AB

For Machines Mfg. Since 7/09

Foot Brake
AD

This lathe is equipped with a foot brake (Figure
38) to quickly stop the spindle. Pushing the foot
brake while the spindle is ON cuts power to the
motor and stops the spindle. Once stopped, the
spindle lever MUST be returned to the neutral
position before the spindle can be restarted.

AE
Spindle ON/OFF Lever

AG
Figure 37. Tailstock controls.

AA. Quill Handwheel: Moves the quill toward or
away from the spindle.
Foot Brake

AB. Graduated scale: Indicates quill movement
in increments of 0.001" or 0.02mm.

Figure 38. Foot brake and spindle ON/OFF lever.

AC. Tailstock Lock Lever: Secures the tailstock in
place along the bedway.
AD. Quill Lock: Locks the quill in position.
AE. Quill: Moves toward and away from the
spindle and holds centers and tooling.
AF. Tailstock Offset Screw: Adjusts and secures
the tailstock offset (1 of 2).
AG. Offset Scale: Indicates the distance of
tailstock offset from the spindle center line.

-26-

Using the foot brake to stop the lathe reduces
risk of an entanglement injury from allowing
the lathe to coast to a stop. Use the foot brake
to stop the lathe whenever possible.

For Machines Mfg. Since 7/09

O P E R AT I O N
3.

Chuck & Faceplate
Mounting
This lathe is shipped with the 3-jaw chuck
installed. This is a scroll-type chuck, meaning
that all three jaws move in unison when
adjusted.

EVS Toolroom Lathes

One at a time, use the chuck key to turn
each of the camlocks counterclockwise until
the cam line aligns with the cam release
datum line, as shown in Figure 40. As you
turn the camlocks, they will rise up slightly
from the spindle body.
Cam Release
Datum Line

The included 4-jaw chuck features independent
jaws, which are used for square or unevenlyshaped stock, and to mount work that needs to
be adjusted to near "0" total indicated runout.

Cam Line

If neither chuck can hold your workpiece, the
cast-iron faceplate has slots for T-bolts that hold
standard or custom clamping hardware. With the
correct clamping hardware, this faceplate will
hold non-cylindrical parts.
The chucks and faceplate have a D-6 camlock
mount. A chuck key is used to turn the locking
cams (Figure 40) to secure/release the chuck/
faceplate.

Items Needed

Figure 40. Camlock loosened with the cam line
aligned with the datum line.

Remove the chuck key, then use a deadblow hammer or a wood block to lightly tap
around the circumference of the chuck or
faceplate to break it free from the spindle
taper and camlock sockets. Be sure to
support the bottom of the chuck.

With a rocking motion, carefully remove the
chuck or faceplate from the spindle nose, as
shown in Figure 41, making sure to support
the weight with an adequate chuck cradle.

Qty

Dead Blow Hammer .............................................. 1
Chuck Cradle or Plywood 3⁄4" (to protect bed) ...... 1
Chuck Key ............................................................. 1

Removing Chuck or Faceplate
1.

DISCONNECT LATHE FROM POWER!

Lay a chuck cradle (see Figure 39) or
plywood under the chuck or faceplate and
over the bedway to protect the precision
ground surfaces from damage and reduce
injury if fingers get pinched.

Figure 41. Example of removing a 3-jaw chuck from a
spindle nose.
Figure 39 Wooden chuck support cradle.

-27-

EVS Toolroom Lathes

O P E R AT I O N

Mounting Chuck or Faceplate
The 4-jaw chuck is shipped with six camlock
studs that must be installed before the chuck
can be mounted, as explained in this procedure.
If you have not yet installed the camlock studs,
complete the instructions in "Installing and
Adjusting Camlock Studs" on Page 29.
To mount a chuck or faceplate:
1.

DISCONNECT LATHE FROM POWER!

Lay a chuck cradle (see Figure 39) or
plywood under the chuck or faceplate and
over the bedway to protect the precision
ground surfaces from damage and reduce
injury if fingers get pinched.

Clean away debris and oily substances from
the mating surfaces of the spindle and chuck
or faceplate.

Inspect and make sure that all camlock
studs are undamaged, are clean and lightly
oiled, and that the camlock stud cap screws
are in place and snug.

For Machines Mfg. Since 7/09

Tighten camlocks in a star pattern to draw
the chuck up evenly on all sides while
reducing chance of alignment, and make
sure to tighten camlocks in an incremental
manner to ensure that no camlock gets fully
tightened all at once (i.e., snug the camlocks
on the first pass, then moderately tighten on
the next pass, then fully tighten on the third
pass).
As you tighten the camlocks, the chuck or
faceplate will snug up onto the spindle nose.
When fully tightened, the cam line will fall
between the two "V" marks on the spindle
nose, as shown in Figure 43.

Cam Line
Between
"V" Marks

Never install a chuck or faceplate without
having the camlock cap screws in place or
fully tightened. If you ignore this notice,
the chuck may not be removable since the
camlock studs may turn with the camlocks
and never release.
5.

Position the chuck/faceplate in front of the
spindle nose, align the chuck timing marks,
as shown in Figure 42, and align the camlock studs with the sockets, then carefully
insert the chuck or faceplate onto the
spindle.

Chuck Timing Marks

Figure 42. Chuck timing marks aligned.

-28-

Figure 43. Camlock fully tightened with the line
between the "V" marks.

Note: If any of the cam lines do not fall between
the "V" marks when the camlock is tight,
you must adjust the offending camlock stud
as discussed in Installing and Adjusting
Camlock Studs on Page 29.
To make sure that the chuck or faceplate is
perpendicularly aligned with the spindle, use
a test indicator mounted on the bedways to
check for runout.

For Machines Mfg. Since 7/09

O P E R AT I O N

Installing and Adjusting Camlock
Studs

Camlock Stud Depth
Mark is Even with Chuck
or Faceplate Surface

When fitting a chuck or faceplate with camlock
studs, or when mounting a new chuck or
faceplate, it may be necessary to install or adjust
the camlock studs.

Tool Needed

Camlock Stud
Locking Cap
Screw Hole

To install or adjust camlock studs onto a chuck or
faceplate:

Lay the chuck or faceplate upside down on a
protective, flat surface.
If installed, remove the locking cap screw
adjacent to each of the six cam-lock
mounting holes (see Figure 44).

Figure 46. Initial adjustment of camlock stud.

Install and tighten the locking cap screws.

Make sure that the cam-lock studs can
rotate back and forth against the head of the
locking cap screw (see Figure 47).

Cam-Lock
Stud

Camlock Stud Can
Rotate Back/Forth
Slightly

Locking
Cap
Screw
Figure 44. Identifying chuck camlock studs and
locking cap screws.

Chuck/Faceplate

Qty

Hex Wrench 6mm ................................................. 1

EVS Toolroom Lathes

Thread each cam-lock stud into the chuck
or faceplate until the depth mark shown in
Figure 45 is even with the surface of the
chuck or faceplate and the curved indent
on the side of the stud faces the locking cap
screw hole, as shown in Figure 46. This is
an initial adjustment.
Depth Mark

Chuck/Faceplate

Cap Screw
Installed & Tight

Figure 47. Camlock stud and cap screw correctly
installed.

Insert the chuck onto the spindle, then check
the position of each camlock, making sure
the cam line points between the "V" marks.
— If one or more of the cams do not point
between the "V" marks on the chuck,
remove the chuck, and fine tune the
camlock stud adjustment by adjusting the
stud in or out and using Figure 48 on
the following page as a guide to correctly
position the cam lines.

Figure 45. Example of camlock stud depth mark.

-29-

EVS Toolroom Lathes

O P E R AT I O N

For Machines Mfg. Since 7/09

Not Correct

Correct

Not Correct

Figure 48. Correct camlock stud alignment.

3-Jaw Chuck
Refer to Chuck & Faceplate Mounting
instructions on Page 27 to mount the 3-jaw
chuck to the spindle.
The 3-jaw scroll-type chuck included with this
lathe features hardened steel jaws that center the
workpiece. When the operator opens or closes the
jaws with the chuck key, the jaws move in unison.
There are two sets of removable hardened steel
jaws included with the 3-jaw chuck—inside and
outside jaws. Use the correct jaws for the size
and configuration of the workpiece to hold it
firmly and securely on the chuck (see Figure
49). The outside of the jaws are used to hold the
workpiece from the outer diameter.

Numbered from 1–3, the jaws must be used in
the matching numbered jaw guides, as shown in
Figure 50.

Jaw Guide #1

Jaw
Numbers

Figure 50 Jaw guides and jaw numbers.

Note: The chuck does not need to be removed
from the spindle to swap the jaws.

Figure 49. Chuck and jaw selection.

-30-

For Machines Mfg. Since 7/09

O P E R AT I O N

— If installed correctly, the jaws converge
together at the center of the chuck.

Changing Jaws
Item Needed

EVS Toolroom Lathes

Qty

Chuck Key ............................................................. 1
White Lithium Grease .......................... As Needed

— If the jaws do not come together, remove
them, then repeat this procedure until
they do.

To change the jaw:
1.

DISCONNECT LATHE FROM POWER!

Mounting Workpiece

Place a piece of wood over the ways to
protect them from potential damage.

Items Needed

Insert the chuck key and turn it
counterclockwise to back the jaws out and
remove them.

Qty

Chuck Key ............................................................. 1
Chuck Cradle or Plywood 3⁄4" (to protect bed) ...... 1
To mount a workpiece in the 3-jaw chuck:
1.

DISCONNECT LATHE FROM POWER!

Clean the jaw mating surfaces and apply
a thin ﬁlm of white lithium grease to the
mating surfaces.

If the workpiece is large and heavy, place a
chuck cradle or plywood on the bedway below
the chuck to protect it.

Set the previously mounted jaws aside in a
safe place free of moisture and abrasives.

Use the chuck key to move the jaws and
mount the workpiece into the chuck (refer to
Figure 52 for typical mounting methods).

Rotate the chuck key clockwise until you
see the tip of the scroll gear lead thread just
begin to enter jaw guide #1 (see Figure 51).

Mounting on an Outside Diameter

Mounting in an Inside Diameter
Lead Thread

Figure 52. Typical of 3-jaw chuck mounting methods.

4.
Figure 51. Inserting jaw guide #1.

Insert jaw #1 into jaw guide #1 and hold the
jaw against the scroll gear lead thread.
Rotate the chuck key clockwise one turn to
engage the tip of the scroll gear lead thread
into the jaw. Pull on the jaw—now it should
be locked into the jaw guide.
Repeat the Steps 6–8 on the remaining jaws.

Rotate the chuck by hand to make sure the
workpiece makes even contact with all three
jaws and spins evenly without any visible
wobble.
— If the workpiece is not evenly held or is
off-center, repeat Steps 3–4.

After verifying that the workpiece is properly
centered, fully tighten the jaws to make sure
the workpiece is held securely, so it will not
come loose during operation.

-31-

O P E R AT I O N

EVS Toolroom Lathes

4-Jaw Chuck
Refer to Chuck & Faceplate Mounting
instructions on Page 27 to mount the 4-jaw
chuck to the spindle.
The 4-jaw chuck features independently
adjustable hardened steel jaws to hold noncylindrical or off-center workpieces. Each jaw can
be removed from the chuck body and reversed for
a wide range of work holding versatility.

For Machines Mfg. Since 7/09

After the workpiece is held in place by
the jaws, turn the chuck by hand and pay
attention to the workpiece alignment.
— If the workpiece is not correctly aligned
for your operation as you turn the chuck,
make fine adjustments by slightly
loosening one jaw and tightening the
opposing jaw until the workpiece is
correctly aligned (see Figure 54 for an
example).

Mounting Workpiece
Items Needed

Qty

Chuck Key ............................................................. 1
Chuck Cradle or Plywood 3⁄4" (to protect bed) ...... 1
To mount a workpiece on the 4-jaw chuck:
1.

DISCONNECT LATHE FROM POWER!

Place a chuck cradle or plywood on the
bedway below the chuck to protect it.

Use the chuck key to open each jaw so the
workpiece will lay flat against the chuck face
or jaw steps.

With help from another person or a
supporting device, mount the workpiece
centered on the chuck, then turn each jaw
until it makes contact with the workpiece.

Tighten each jaw in small increments. After
you have adjusted the first jaw, continue
tightening in an opposing sequence, as
shown in Figure 53.

Figure 54. Example of non-concentric workpiece
correctly mounted on the 4-jaw chuck.

Tailstock
The tailstock (Figure 55) on your lathe can be
used to support workpieces with the use of a live
or dead center (refer to Centers on Page 37).
It can also be used to drill or bore holes in the
center of a part or cut shallow tapers by using
the offset adjustment.

3
Workpiece
Center Point

Figure 53. 4-jaw tightening sequence.

-32-

Quill
Handwheel

Tailstock Lock
Lever

Quill Lock
Lever

Figure 55. Tailstock and quill lock handles in locked
position.

For Machines Mfg. Since 7/09

O P E R AT I O N

Moving Along Bedway

EVS Toolroom Lathes

To install tooling in the tailstock:

Pull the tailstock lock lever backward (away
from the spindle) to unlock the tailstock from
the bedway.

With the tailstock locked in place, unlock the
quill, then use the handwheel to extend it to
the 1" mark on the quill.

Slide the tailstock to the desired position.

Push the tailstock lock lever forward (toward
the spindle) to lock the tailstock to the
bedway.

Insert the drill chuck arbor or drill shank
into the quill, then quickly slap it in. Try to
twist the tool to check if it is firmly seated. A
firmly seated taper will not twist.

Using Quill
1.

Release the quill lock lever.

Turn the quill handwheel clockwise to
move the quill towards the spindle, or turn
counterclockwise to move the quill away
from the spindle.

Push the quill lock forward to lock the quill
in place.

Note: If the tapered shaft has a tang, align it
horizontally with the indent in the back of
the quill before fully inserting it.
3.

Unlock the tailstock and move it until the
tip of the cutting tool is close to, but not
touching, the workpiece, then re-lock the
tailstock.

Start spindle rotation, unlock the quill, then
turn the quill handwheel clockwise to feed
the cutting tool into the workpiece.

Installing Tooling

Removing Tooling

The tailstock quill can hold live or dead centers
(refer to Mounting Center in Tailstock on
Page 38) or any MT#4 taper tooling, such as a
chuck arbor or tapered drill bit (see Figure 56).

Use a shop rag to hold the tool.

Rotate the tailstock quill handwheel
counterclockwise until the tool is forced out
of the quill.

Tang

MT#4 Taper

Tang

MT#4 Taper
Figure 56. Inserting drill chuck arbor or tapered drill
bit into tailstock.

-33-

O P E R AT I O N

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Offsetting

Aligning

The tailstock can be offset from the spindle
center line for turning tapers. The offset
movement is controlled by set screws on both
sides of the tailstock (see Figure 57), and the
amount of movement is indicated by the offset
scale on the back of the tailstock.

The offset of your lathe was aligned with
the spindle center line at the factory. We
recommend that you take the time to ensure
that the tailstock is aligned to your own desired
tolerances, especially if you have changed the
offset to cut shallow tapers.

Note: For a precise offset, use a dial indicator to
check quill movement while adjusting screws.

To align the tailstock offset to the spindle center
line:
1.

Set Screw
(1 of 2)

— If the bedway is not level, correct this
condition before continuing with this
procedure.

Offset
Scale

Figure 57. Tailstock offset controls.

Tool Needed

Qty

Hex Wrench 6mm ................................................. 1
To offset the tailstock from the spindle center
line, loosen the clamp bolts underneath the
tailstock to relieve pressure on the sliding
components, then rotate the set screws in the
direction shown in Figure 58.

Turn
CCW

Turn
CW

Use a precision level to make sure the
bedway is level from side-to-side and from
front-to-back.

Obtain two pieces of steel round stock 2" in
diameter and 6" long.

Center drill both ends of one piece of round
stock, then set it aside for use in Step 6.

Use the other piece of round stock to make
a dead center, and turn it to a 60° point, as
shown in Figure 59.

Turn
CCW
Figure 59. Turning a dead center.

Figure 58. Set screw adjustment in relation to
tailstock movement.

Once the tailstock is offset where needed, tighten
the clamp bolts underneath the tailstock.

-34-

For Machines Mfg. Since 7/09

O P E R AT I O N

Note: As long as this dead center remains in the
chuck, the point of the center will remain
true to the spindle center line. The point will
have to be refinished whenever the center is
removed and then returned to the chuck.
5.

Install a center in the tailstock.

Attach a lathe dog to the piece of stock from
Step 3, then mount it between the centers,
as shown in Figure 60.

EVS Toolroom Lathes

Use a caliper to measure both ends of the
workpiece.
— If the machined workpiece is thicker
at the tailstock end, move the tailstock
toward the operator 1⁄2 the distance of the
amount of taper (see Figure 61).

Move the tailstock toward
the operator half the
distance of the taper.

Looking down from above.

Figure 61. Adjust tailstock toward the operator.

Figure 60. Example of round stock mounted between
the centers.

Turn 0.010" off the diameter of the stock.

Mount a test or dial indicator so that the
plunger is on the tailstock quill.

— If the machined workpiece is thinner at
the tailstock end, move the tailstock away
from the operator 1⁄2 the distance of the
amount of taper (see Figure 62).
Looking down from above.

Note: If necessary in the following step, refer to
"To Set Up the Tailstock to Cut a Shallow
Taper" on Page 34 for adjusting the
tailstock offset.
Move tailstock away from
the operator half the
distance of the taper.
Figure 62. Adjust tailstock away from the operator.

10. Repeat Steps 7–9 until the desired accuracy
is achieved.

-35-

EVS Toolroom Lathes

O P E R AT I O N

Faceplate

For Machines Mfg. Since 7/09

Non-Cylindrical
Workpiece

Refer to Chuck & Faceplate Mounting
instructions on Page 27 to mount the faceplate
to the spindle.
The 12" faceplate included with your lathe offers
a wide range of uses, including machining nonconcentric workpieces, straight turning between
centers, off-center turning, and boring.

Clamp

The tools needed for mounting a workpiece will
vary depending on the type of setup you have.

Faceplate
Figure 63. Example of workpiece clamped in a
faceplate.

Failure to properly secure a workpiece to the
faceplate could cause the workpiece to be
thrown from the lathe with deadly force at the
operator or bystanders. Use a minimum of
three independent clamping devices to hold a
non-concentric workpiece onto the faceplate.

Machining non-concentric workpieces at a
high speed could cause the workpiece to be
thrown from the spindle with deadly force at
the operator or bystanders. To reduce this
risk, only machine non-concentric workpieces
at low speeds and clamp counter-weights to
the faceplate to balance it.

Mounting Workpiece with Clamps
1.

DISCONNECT LATHE FROM POWER!

Place a piece of 3⁄4" plywood on the bedway
below the spindle.

With help from another person, place the
workpiece onto the faceplate and clamp it in
place with a minimum of three independent
clamping devices (see Figure 63 for an
example).

Note: Be sure to take into account the rotation
and cutting forces that will be applied to the
workpiece when clamping it to the faceplate.
4.

-36-

Double check tool and slide motion
clearances before turning spindle ON.

Mounting Workpiece Between
Centers
1.

DISCONNECT LATHE FROM POWER!

Drill center holes in both ends of the
workpiece.

Install the dead center in the spindle and the
live center or carbide-tipped dead center in
the tailstock (refer to Page 37).

Secure a lathe dog on the spindle-end and
place a drop of oil in the center hole on the
tailstock-end of the workpiece.

Mount the workpiece between centers so the
lathe dog tail fits freely in the faceplate slot
without binding.

Faceplate

Dead Center

Lathe Dog
Figure 64. Example of using faceplate to mount work
between centers.

For Machines Mfg. Since 7/09

O P E R AT I O N

EVS Toolroom Lathes

Centers

Mounting Dead Center in Spindle

Figure 65 shows the dead centers included with
the lathe. In addition, an MT#6–MT#4 tapered
spindle sleeve is included for mounting centers in
the spindle.

DISCONNECT LATHE FROM POWER!

Thoroughly clean and dry the tapered
mating surfaces of the spindle bore, tapered
sleeve, and the center, making sure that no
lint or oil remains on the tapers.

Insert the center into the sleeve, then insert
the sleeve into the spindle bore through the
chuck or faceplate.

Tapered
Sleeve

Dead Center

Carbide Tipped
Dead Center

Figure 66 shows an example of the dead
center installed in the spindle, using a
lathe dog and faceplate for turning between
centers.

Dead Center
Figure 65. Tapered sleeve and dead centers.

Dead Centers
The dead center achieves more accurate results
than a live center, but it requires low spindle
speeds and a small amount of oil to reduce
friction heat that may damage the workpiece.
Use the dead center in the spindle, because the
workpiece does not rotate on the tip and does not
generate friction.
Use the carbide-tipped dead center in the
tailstock where the workpiece will rotate against
it and generate friction. The carbide-tipped dead
center can better withstand the effects of friction;
however, the tip of the center must be lubricated
to avoid premature wear and maximize smooth
operation. Also, using low spindle speeds will
reduce the heat and wear from friction.

Figure 66. Example of using a dead center with a
faceplate and lathe dog.

To avoid premature wear of the dead center
or damage to the workpiece, use low spindle
speeds and keep the tip of the dead center
mounted in the tailstock well lubricated.

Live Centers
A live center has bearings that allow the center
tip and the workpiece to rotate together, and can
be installed in the spindle and the tailstock quill
for higher speeds.

-37-

O P E R AT I O N

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Removing Center from Spindle

To mount a center in the tailstock:

To remove the sleeve and center from the
spindle, insert a piece of round bar stock or
similar tool through the outboard end (on the left
side of the headstock), then tap the sleeve loose.

DISCONNECT LATHE FROM POWER!

Thoroughly clean and dry the tapered
mating surfaces of the tailstock quill bore
and the carbide-tipped dead center, making
sure that no lint or oil remains on the tapers.

Use the tailstock quill handwheel to feed the
quill out from the casting about 1". (Do not
feed the quill out of the casting more than 2"
or stability and accuracy will be reduced.)

Insert the center into the tailstock quill.

Seat the center firmly into the quill during
workpiece installation by rotating the quill
handwheel clockwise to apply pressure, with
the center engaged in the center hole in the
workpiece.

Note: Hold onto the sleeve and center as you tap
them loose to avoid dropping them and damaging
the tip of the center or the bedways.

Mounting Center in Tailstock
Either a dead center or live center can be
mounted in the tailstock. Mounting instructions
are the same for both. Figure 67 shows an
example of a dead center mounted in a tailstock.

Dead Center

Note: Only apply enough pressure with the
tailstock quill to securely mount the
workpiece between centers. Avoid overtightening the center against the workpiece,
or it may become difficult to remove later,
and it will result in excessive friction and
heat, which may damage the workpiece and
the center.
Figure 67. Example of using a dead center installed in
the tailstock.

-38-

Removing Center from Tailstock
To remove the center from the quill, hold onto it
with a rag in one hand, then rotate the tailstock
handwheel counterclockwise to draw the quill
back into the casting until the center releases.

O P E R AT I O N

For Machines Mfg. Since 7/09

Steady Rest
The steady rest supports long shafts and can be
mounted anywhere along the length of the bed.

EVS Toolroom Lathes

Close the steady rest so that the workpiece
is inside the finger rollers, then tighten the
lock knob.

Loosen the three wing bolts so the finger
roller positions can be adjusted.

To install and use the steady rest:
1.

DISCONNECT LATHE FROM POWER!

Thoroughly clean the machined base of
the steady rest, then place it on the lathe
bedways so the triangular notch fits over the
bedway prism.

Use the finger adjustment knobs to
just touch the finger rollers against the
workpiece without causing workpiece
deflection.

Tighten the three wing bolts.

Position the steady rest where required to
properly support the workpiece, then tighten
the hex nut shown in Figure 68 to secure it
in place.
Lock Knob

Finger
Adjustment
Knob
Wing
Bolt

Note: The finger rollers should properly support
the workpiece but allow it to freely rotate.

Follow Rest
The follow rest mounts to the saddle with two
cap screws (Figure 70). It is used on long,
slender parts to prevent workpiece flexing from
the pressure of the cutting tool during operation.
Adjust the sliding finger rollers on the follow rest
in the same manner as those on the steady rest.

Finger Roller
Hex Nut
Cap Screws
Figure 68. Steady rest components.

Loosen the lock knob and open the steady
rest so the workpiece can rest on the bottom
two finger rollers, as shown in Figure 69.

!
Figure 70% Follow rest attachment.

Figure 69. Workpiece mounted in the steady rest.

-39-

O P E R AT I O N

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Compound Slide

Four-Way Tool Post

The compound slide handwheel has an indirectread graduated scale. This means that the
distance shown on the scale represents the
actual distance the tool moves, which will remove
twice as much material from the diameter of the
workpiece. The base of the compound slide has
another graduated scale used for setting the tool
to a specific angle.

The four-way tool post is mounted on top of the
compound slide and allows a maximum of four
tools to be loaded simultaneously.
The four-way tool post allows for quick indexing
to different tools, which is accomplished by
loosening the top handle, rotating the tool post
to the desired position, then re-tightening the
handle to lock the tool into position.

To set the compound slide at a certain angle:
Loosen the two hex nuts at the base of the
compound slide (1 of 2 shown in Figure 71).

Tool Needed

Qty

Tool Post T-Wrench............................................... 1

To load the tool post:
Compound
Slide

Hex Nut

Choose the desired cutting tool.

Loosen the tool post bolts so that the cutting
tool can fit underneath them.

Note: If necessary, place one steel shim
underneath the cutting tool so the cutting tip
is properly aligned with the workpiece. The
shim should be as long and as wide as the
cutting tool to properly support it.

Figure 71. Compound slide set at an angle.

Rotate the compound to the desired angle,
as indicated by the scale at the base, then
retighten the two hex nuts.
— If setting up to cut external right-hand
inch or metric threads, or left-hand
internal threads for the ﬁrst time, set
the compound so its travel is perfectly
parallel with the cross slide. Using a
protractor, rotate the compound 29.5°
counterclockwise and mark the new
location on the compound slide. This
mark will be the quick reference point
for setting the offset angle. To mark for
internal right-hand threads, or left-hand
external threads, repeat this process, but
rotate the compound 29.5° clockwise and
mark the cross slide accordingly.

Over-extending a cutting tool from the tool
post will increase the risk of it breaking during
operation, which may cause metal pieces to
be thrown at the operator or bystanders with
great force. Only extend a cutting tool 2.5
times the width of its cross-section or less
(i.e., 2.5 x 0.5" = 1.25").
3.

Firmly secure the cutting tool with at least
two tool post bolts (Figure 72).
Tool Post Bolts

Top
Handle

Cutting Tool
Figure 72. Example of 4-way tool post.

-40-

For Machines Mfg. Since 7/09

O P E R AT I O N
Tools Needed

Aligning Cutting Tool with
Tailstock Center
For most operations, the cutting tool tip should
be aligned with the spindle center line, as
illustrated in Figure 73.

Tool Post T-Wrench............................................... 1
Steel Shim ............................................. As Needed
Cutting Tool........................................................... 1
Fine Ruler .............................................................. 1
Tailstock Center .................................................... 1

Mount the cutting tool in the tool post, then
turn the tool post so the tooling faces the
tailstock.

Install a center in the tailstock, and position
the center tip near the tip of the cutting tool.

Lock the tailstock and quill in place.

Adjust the height of the cutting tool with a
steel shim, so the tip just touches the end of
the tailstock center, as shown in Figure 74.

Workpiece

Figure 73. Cutting tool aligned with workpiece center
(view from tailstock).

There are a number of ways to check and align
the cutting tool to the spindle center line. Below
are two common methods:

Qty

To align the cutting tool with the tailstock
center:

Workpiece
Center
Cutting Line
Tool

EVS Toolroom Lathes

Align the tip of the cutting tool with a
center installed in the tailstock (refer to the
instructions that follow). For this to work,
the tailstock must be aligned to the spindle
center line (refer to Aligning Tailstock on
Page 34).
-AKE A FACING CUT ON A PIECE OF ROUND BAR
stock. If the tool is above/below the spindle
center line, a nub will be left in the center
of the workpiece. Adjust the height of the
workpiece, then repeat the facing cut to
check the adjustment. Repeat as necessary
until the center of the workpiece is smoothly
faced.

(Top View)

Tailstock
Center
Cutting
Tool
Cutting
Tool

Tailstock
Center

(Side View)
Figure 74. Cutting tool tip aligned with tailstock
center.

-41-

O P E R AT I O N

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Adjustable Apron Stop Carriage Stop
System
Use the adjustable apron stop collar (shown in
Figure 75) to set the location where the carriage
will be disengaged by the feedrod friction clutch.
When the adjustable apron stop contacts the stop
collar during a carriage feeding operation, the
clutch disengages the feedrod from the apron and
the carriage movement stops.

Apron

The carriage stop on this lathe will NOT
automatically stop the carriage or disengage
the power feed! Failure to heed this notice
could result in the carriage crashing and
causing severe machine or property damage.
Use the carriage stop as a guide to help judge
when to stop the carriage movement.

Tools Needed

Qty

Hex Wrench 8mm ................................................. 1
To adjust the carriage stop:
1.

DISCONNECT LATHE FROM POWER!

Loosen the cap screws shown in Figure 76.
Cap Screws Stop Rod

Stop Collar

Apron Stop

Figure 75. Adjustable apron stop and collar.
Adjustment
Knob

The adjustable apron stop system is designed
to stop the longitudinal carriage movement
at optional locations when the feedrod is
engaged.
When the leadscrew is engaged for threading
operations, the adjustable apron stop system
will not disengage the leadscrew—you must
move the half nut lever instead. Otherwise,
the carriage can crash into the chuck, or if it
contacts the stop, the leadscrew shear pin will
break.

Figure 76. Carriage stop.

Use the carriage handwheel to position the
carriage/cutting tool at the stop point you
want to set (typically the maximum distance
the carriage can travel before there is a
crash).

Position the carriage stop so the rod is
firmly against the carriage, retighten the
cap screws loosened in Step 2, and use the
adjustment knob to fine tune the position of
the stop rod.

Move the carriage away from the stop rod,
then move it back against the stop rod and
verify that tooling will not make contact with
chuck, jaws, or other components (rotate the
chuck by hand to verify rotational clearance).

Before doing any threading operations, make
sure to loosen the stop collar so it slides
freely on the feedrod.

-42-

O P E R AT I O N

For Machines Mfg. Since 7/09

EVS Toolroom Lathes

Manual Feed

Spindle Speed

You can manually move the cutting tool around
the lathe for facing or turning operations using
the handwheels shown in Figure 77 and
described below.

Using the correct spindle speed is important
for safe and satisfactory results, as well as
maximizing tool life.

Cross Slide
Handwheel

Compound Slide
Handwheel

Carriage
Handwheel

To set the spindle speed for your operation, you
will need to: (1) Determine the best spindle speed
for the cutting task, and (2) configure the lathe
controls to produce the required spindle speed.

Determining Spindle Speed
Many variables affect the optimum spindle speed
to use for any given operations, but the two most
important are the recommended cutting speed
for the workpiece material and the diameter of
the workpiece, as noted in the formula shown in
Figure 78:

Figure 77. Carriage Controls.

Carriage Handwheel
The carriage handwheel moves the carriage left
or right along the bed. Use this control when
setting up the machine for facing or turning.

Cross Slide Handwheel
The cross slide handwheel moves the tool toward
and away from the work. Turning the dial
clockwise moves the slide toward the workpiece.
Adjust the graduated scale by holding the
handwheel with one hand and turning the dial
with the other. The graduated scale reads in
0.001" increments and is a "direct-read" which
means that the distace on the collar reflects
the amount removed from the diamter of the
workpiece.

Compound Slide Handwheel
The compound slide handwheel controls the
position of the cutting tool relative to the
workpiece. The compound is adjustable for any
angle within its range. Angle adjustment is
secured by two nuts on the base of the compound.
The graduated scale reads in 0.001" increments
and is a "indirect-read" which means that the
distace on the collar reflects the distance that the
tool moves.

*Recommended
Cutting Speed (FPM) x 12

= SpindleSpeed (RPM)

Dia. of Cut (in inches) x 3.14

*Double if using carbide cutting tool
Figure 78. Spindle speed formula for lathes.

Cutting speed, typically defined in feet per
minute (FPM), is the speed at which the edge of a
tool moves across the material surface.
A recommended cutting speed is an ideal speed
for cutting a type of material in order to produce
the desired finish and optimize tool life.
The books Machinery’s Handbook or Machine
Shop Practice, and some internet sites, provide
excellent recommendations for which cutting
speeds to use when calculating the spindle speed.
These sources also provide a wealth of additional
information about the variables that affect
cutting speed and they are a good educational
resource.
Also, there are a large number of easy-to-use
spindle speed calculators that can be found on
the internet. All of these sources will help you
take into account all the applicable variables in
order to determine the best spindle speed for the
operation.

-43-

O P E R AT I O N

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Setting Spindle Speed
Make sure the spindle is turned OFF and it
has come to a complete stop.

Use the chart in Figure 79 to determine the
available spindle speed range closest to your
calculated spindle speed.

SPEEDS

LEVER

RPM

Low

20-400

High

400-2500

Figure 79. Spindle speed range chart.

If the headstock is in high range (400-2500
RPM), and if the spindle speed dial is turned
completely to the left, the tachometer may
show a speed lower than the 400 RPM listed
on the headstock label. This headstock label
indicates the allowable spindle speed for
cutting operations within that range. If the
lever is in high range, do not attempt cutting
operations below 400 RPM.
Adjust the spindle speed range lever to the
range that covers your calculated spindle
speed.

Note: To shift the spindle speed range lever, you
may need to apply pressure to the lever and
slightly rotate the spindle by hand.
Spindle Speed Dial

Low
20-400 RPM

High
400-2500 RPM

Figure 80. Controls used to adjust spindle speed.

-44-

Make sure the variable speed dial is turned all
the way to the left (counterclockwise) before
turning the lathe ON, or it may start up at a
dangerously high rate of speed.
Turn the spindle ON and slowly turn the
variable speed dial to carefully adjust the
spindle speed (shown on the digital display)
to your calculated spindle speed.

Power Feed
On this machine, both the carriage and cross
slide have power feed capability. The rate that
these components move (feed rate) is controlled
by how the levers are conﬁgured on the gearbox.
Feed rate and spindle speed must be considered
together. The sources you use to determine the
optimum spindle speed for an operation will also
provide the optimal feed rate to use with that
spindle speed.
Often, the experienced machinist will use the
feeds and speeds given in their reference charts
or web calculators as a starting point, then
make minor adjustments to the feed rate (and
sometimes spindle speed) to achieve the best
results.
The carriage can alternately be driven by the
leadscrew for threading operations. However,
this section covers using the power feed option
for the carriage and cross slide components for
non-threading operations. To learn how to power
the carriage for threading operations, refer to the
Threading Controls section Page 48.

O P E R AT I O N

For Machines Mfg. Since 7/09

Power Feed Controls
The feed direction lever (Figure 81) controls
direction of the carriage. The quick change
feed direction knob (Figure 82) reverses the
feed direction of the carriage while the lathe is
running.
FORWARD
NEUTRAL

EVS Toolroom Lathes

Use the feed control lever on the front of the
apron to engage power feed for either the
carriage or the cross slide (see Figure 83).
To engage the carriage, push the lever to
the left and down. To engage the cross slide,
push the lever to the right and up.

Note: Sometimes you need to slightly rotate the
handwheel of the component you are trying
to engage, so that the gears can mesh.

REVERSE

Cross Feed

Feed Direction Lever
Figure 81. Feed direction lever.

Neutral

Carriage Feed

Figure 83. Feed control lever positions.

To use the quick change feed direction knob:

Figure 82. Quick change feed direction knob.

To engage the power feed:
1.

Make sure the spindle is OFF and has come
to a complete stop.

Use the feed direction lever to select the
direction that the feed rod will rotate.

While the lathe is running, place the feed
control lever in neutral.

Push or pull the quick change feed direction
knob to change the direction of the feed rod.

Re-engage the feed direction lever. The feed
rod rotation will now be reversed, causing
the engaged carriage or cross slide to move
in the opposite direction.

Note: The feed rod rotation will be the reverse of
what is shown on the control panel diagram
if the quick change feed direction knob is
engaged.

DO NOT move the feed direction lever on
the headstock while the spindle is turning, or
damage will occur to the headstock gearing.

-45-

O P E R AT I O N

EVS Toolroom Lathes

For Machines Mfg. Since 7/09

Understanding Thread & Feed Rate Chart
Figure 84 shows the configurations of gearbox levers that are required to set the available feed rates.
This same chart can also be found on the machine.
METRIC
THREADING

INCH
THREADING

MODULAR OR
DIAMETRAL

TURNING FEED RATE
(DIST./REVOLUTION)

in.

.2
LCT1Z
.225 LCT2Z
.25 LCT3Z

2.0
2.5
3.0

LCR1Y
LCR3Y
LCR6Y

.3
.35
.4

LCT6Z
LCT8Z
LCS1Z

3.5
4.0
4.5

LCR8Y
HCR3Z
HCS2Y

.45
.5
.6

LCS2Z
LCS3Z
LCS6Z

5.0
5.5
6.0

HCS3Y
HCS4Y
HCS6Y

.7
.75
.8

LCS8Z
LCT6Y
LCR1Z

6.5
7
8

HCS7Y
HCS8Y
HCR1Y

.9
1.0
1.1

LCR2Z
LCR3Z
LCR4Z

9
10
11

HCR2Y
HCR3Y
HCR4Y

1.2
1.25
1.3
1.4
1.5
1.75

LCR6Z
LCS3Y
LCR7Z
LCR8Z
LCS6Y
LCS8Y

12
13
14

HCR6Y
HCR7Y
HCR8Y

72
60
56
54
48
44
40
36
32
30
28
27
26
24
23
22
20
19
18
16
15
14
13½
13

LAR6V
LAR3V
LBR8V
LAR2V
LBR6V
LBR4V
LBR3V
LAS6V
LBR1V
LAS3V
LBS8V
LAS2V
LBS7V
LBS6V
LBS5V
LBS4V
LBS4V
LCS2V
LBS2V
LBS1V
LAT3V
LBT8V
LAT2V
LBT7V

12
11½
11
10
9
8
7½
7
6

LBT6V
LBT5V
LBT4V
LBT3V
LBT2V
LBT1V
HAS3V
HBS8V
HBS6V

5
4½
4

HBS3V
HBS2V
HBS1V

3¾
3½
3¼

HAT3V
HBT8V
HBT7V

3
HBT6V
2 7⁄8 HBT5V
2¾ HBT4V
2½
2¼
2

HBT3V
HBT2V
HBT1V

Mod.
.3
.4
.5

HCT6Z
HCS1Z
HCS3Z

.6
.7
.8

HCS6Z
HCS8Z
HCR1Z

44
40
36
32
30
28
26

HBR4V
HBR3V
HAS6V
HBR1V
HAS3V
HBS8V
HBS7V

2.25 HCR2Y
2.5 HCR3Y
2.75 HCR4Y

24
22
20
19
18
16
15
14
13
12
11

HBS6V
HBS4V
HBS3V
HCS2V
HBS2V
HBS1V
HAT3V
HBT8V
HBT7V
HBT6V
HBT4V

3.0 HCR6Y
3.25 HCR7Y
3.5 HCR8Y

10 HBT3B
9 HBT2V
8 HBT1V

.9 HCR2Z
1.0 HCR3Z
1.25 HCS3Y
1.5 HCS6Y
1.75 HCS8Y
2.0 HCR1Y

in.

.050 LCT1W

.002

.055 LCT2W
.065 LCT4W
.085 LCT8W

.0022
.003
.0033

.10
.13
.18

LCS2W
LCS4W
LCS8W

.004
.005
.007

.22
.28
.35

LCR3W
LCR4W
LCR8W

.009
.011
.014

.44

LCS8X

.017

.55
.68
.85

LCR2X
LCR3X
LCR8X

.022
.027
.033

HCS2X
HCS4X
HCS8X

.047
.055
.067

D.P.

1.2
1.4
1.7

Figure 84. Thread and feed rate chart.

Positioning Gearbox Levers
To cut a particular thread or establish a
particular feed rate, you may need to first swap
the gearbox drive gear, depending on where it is
currently set (refer to End Gear Setup on Page
47).
Once you have confirmed that the end gear is
set up properly, you can then move the gearbox
levers to the required positions. The arrows
going from Figure 84 to Figure 85 show which
gearbox levers must be moved to achieve an
example feed rate.

-46-

Figure 85. Gearbox levers set for a feed rate of 0.014"
(0.35mm).

O P E R AT I O N

For Machines Mfg. Since 7/09

EVS Toolroom Lathes

End Gear Setup

Alternate Position

The gearbox drive gear on this lathe can be
configured for the "normal position" or the
"alternate position" (both described in following
paragraphs), depending upon the type of
operation to be performed. The lathe is shipped
with the end gears in the normal position. Gears
must be thoroughly cleaned and re-coated in
grease before installing (refer to Page 61), and
the backlash must be maintained at 0.005" for
correct meshing.

When the 44- and 57-tooth end gears are meshed
(see Figure 87), you can perform modular and
diametral pitch turning.

24T
56T
44T
Modular and Diametral
Pitch Turning

Normal Position
The 24T end gear is installed in the top position,
the 44T/56T end gears in the middle position,
and the 57T end gear in the bottom position, as
shown in Figure 86. In the normal position, the
56T and 57T gears are meshed, which allows for
inch and metric threading and all general feed
operations.
24T
44T
56T

57T
Figure 87. Alternate end gear position.

Conﬁguring End Gears
1.

DISCONNECT LATHE FROM POWER!

Move the gearbox range lever to "Low" so
that the gears will not rotate in the following
steps, then open the lathe headstock side
cover.

To change the position of the 57T gear:
a.

57T

Remove the cap screw and flat washer
that secures the gear, then remove the
gear (see Figure 88).
Spacer

24T
56T
Inch and Metric Pitch
Threading

Cap Screw and
Washer

57T

Inch and Metric Feeding
Figure 88. Removing the end gear.

Figure 86. Normal end gear position.

-47-

EVS Toolroom Lathes

O P E R AT I O N

For Machines Mfg. Since 7/09

Note: Take care not to misplace the key from the
gear shaft.
b.

Clean away debris and grime from the
gear and apply a light coat of machine
oil.
Swap the position of the gear, as shown
in Figure 87, then align it with the key
and insert it on the gear shaft.
Re-install the flat washer and cap screw.

Note: DO NOT overtighten the cap screw. The
cap screw merely holds the gear in place
and overtightening it will make it harder to
remove later and may restrict its rotation.
Close and secure the headstock side cover.

Cross Slide
Neutral
Carriage

Threading Controls
If you are unfamiliar with how to cut threads on
a lathe, we strongly recommend that you read
books, review industry trade magazines, or get
formal training before beginning any attempting
any threading projects.

Power Feed Lever
The feed control lever must be in the neutral
(horizontal) position for threading operations or
the half nut will not engage with the leadscrew
(see Figures 89–90).

FEED CONTROL
LEVER

Disengaged

Engaged

Figure 90. Feed control lever and half nut positions
for threading.

Half Nut Lever
The half nut lever engages the carriage with the
leadscrew which moves the cutting tool along the
length of the workpiece (see Figure 89).

When threading, we recommend using the
slowest speed possible and avoiding deep
cuts, so you are able to disengage the half nut
and prevent an apron crash!

Thread Dial & Chart Overview
The numbers on the thread dial are used with
the thread dial chart to show when to engage the
half nut during inch threading. The thread dial
gear must be engaged with the leadscrew for this
to work. Loosen the knurled hand knob on the
thread dial, pivot the dial gear into mesh with
the leadscrew, then tighten the hand knob (see
Figure 91).
Leadscrew

Feed Control Lever

Half Nut Lever
Down & Engaged
Hand Knob

Dial Gear

Figure 89. Carriage controls set up for threading.
Figure 91. Thread dial engaged with the leadscrew.

-48-

O P E R AT I O N

For Machines Mfg. Since 7/09

EVS Toolroom Lathes

Using Thread Dial and Chart

TPI 2-54 Not Divisible By 4

Find the TPI (threads per inch) that you want
to cut in the left column (see Figure 92), then
reference the dial number to the right of it. The
dial numbers indicate when to engage the half
nut for a speciﬁc thread pitch. The thread dial
chart can also be found on the front of the thread
dial housing.

Use any of the non-numbered lines on the thread
dial for threading the TPI shown in Figure 94.
TPI

2,6,10,14,
18,22,26,
30,54

NonNumbered
Position

4,8,12,16,20,24,
28,32,36,40,44,
48,56,60,72
2,6,10,14,
18,22,26,
30,54
3,5,7,9,
11,13,15,
19,23,27
2½,3½,4½,
7½,11½,13½
2¼,2¾,
3¼,3¾
27⁄8

In.

Any Position

NonNumbered
Position
Numbered
Position
1,2,3,4
Position
1,3 or 2,4
Position
1 Only
Same as
Metric
Threads

Figure 94. Marks are selected on the dial for threading
2-54 TPI.

Odd Numbered TPI
Use any of the numbered lines on the thread dial
for threading the TPI shown in Figure 95.
TPI

3,5,7,9,
11,13,15,
19,23,27

Numbered
Position
1,2,3,4

Figure 92. Thread dial chart.

The thread dial is not used for metric threading
or for diametral or modular gear turning. You
must leave the half nut lever engaged from the
beginning until the threads are complete for
these types of operations.
The following examples explain how to use the
thread dial chart.

Figure 95. Numbers are selected on the dial for
threading odd numbered TPI.
1

⁄2 Fractional TPI

Use any opposing number pairs—2/4 or 1/3 on
the thread dial for 1⁄2 fractional TPI (Figure 96).
For example, to cut a 31⁄2 thread, select 1 on the
dial, then start threading, using 1 or 3 as your
reference points.

TPI 4-72 Divisible By 4
Use any line (position) on the thread dial, shown
in Figure 93, for threading TPI divisible by four.

TPI

2½,3½,4½,
7½,11½,13½

Position
1,3 or 2,4

TPI

4,8,12,16,20,24, Any Position
28,32,36,40,44,
48,56,60,72

Figure 96. Opposing number group are selected on
dial for cutting 1⁄2 thread TPI.

Figure 93. Any position on the dial for threading 4-72
TPI.

-49-

EVS Toolroom Lathes

O P E R AT I O N

Other Fractional TPI
Use position 1 on the thread dial for cutting the
TPI shown in Figure 97.

2¼,2¾,
3¼,3¾

Position
1 Only

For Machines Mfg. Since 7/09

Chip Drawer
The chip drawer shown in Figure 99 catches
swarf and metal chips during the machining
process. It easily slides open to provide access to
swarf during cleanup.
Also, the chip drawer contains a screen that
allows runoff cutting fluid to drain back into the
cutting fluid tank.

Figure 97. Any number on dial is selected for other
fractional TPI.

27⁄8 TPI
Use any numbered or non-numbered line on the
thread dial to cut the TPI shown in Figure 98.

27⁄8

Same as
Metric
Threads

Figure 98. Any number on the dial can be selected for
27⁄8 TPI.

-50-

Figure 99. Chip drawer.

If pulled out quickly and more than half of the
way, the drawer could fall out and hit your
feet, causing serious injury. Therefore, open
the drawer slowly and avoid opening it more
than half of the way.

O P E R AT I O N

For Machines Mfg. Since 7/09

EVS Toolroom Lathes

Cutting Fluid System
The cutting ﬂuid system delivers cutting ﬂuid
through a positionable nozzle and is turned ON/
OFF by the control panel cutting ﬂuid pump
switch and the valve lever near the base of the
nozzle hose (see Figure 100).

BIOLOGICAL & POISON
HAZARD!
Use the correct personal
protection equipment
when handling cutting
fluid. Follow federal, state,
and fluid manufacturer
requirements for proper
disposal.

Nozzle

Valve
Lever

Running the pump without adequate fluid in
the tank may permanently damage it. This is
abuse and is not covered by the warranty.

Cutting Fluid
Pump Switch

To use the cutting ﬂuid system on your lathe:
1.

Make sure the tank is properly serviced and
filled with cutting fluid, and that you wear
the necessary personal protection equipment.

Position the cutting fluid nozzle for your
operation.

Use the control panel cutting fluid pump
switch to turn the coolant pump ON.

Adjust the flow of cutting fluid by using the
valve lever near the base of the nozzle hose.

Figure 100. Coolant system controls and components.

Always use high quality cutting ﬂuid in your
coolant system and follow the manufacturer's
instructions for diluting. The quick reference
table shown in Figure 101 can help you select
the appropriate cutting fluid.
Refer to Cutting Fluid System on Page 62 for
detailed instructions on how to add or change
cutting fluid. Check the cutting ﬂuid regularly
and promptly change it when it becomes overly
dirty or rancid, or as recommended by ﬂuid
manufacturer.
Workpiece

Dry

Aluminum

Note: Promptly clean any splashed cutting fluid
from the floor to avoid a slipping hazard.

Water
Soluble Oil

Synthetic
Coolants

Sulferized
Oil

Mineral
OIl

Brass

Bronze

Cast iron

Low Carbon Steel

Alloy Metals

Stainless Steel

General Note: Cutting fluids are used for heavy-duty lathe operations and production turning. Oil-water
emulsions and synthetic cutting fluids are the most common for typical lathe operations. Sulferized oils
often are used for threading. For small projects, spot lubrications can be done with an oil can or brush, or
omitted completely.

Figure 101. Cutting fluid selection table.

-51-

EVS Toolroom Lathes

ACC ESSOR I ES

ACCESSORIES

Accessories
This section includes the most common
accessories available for your lathe, which may
be available through your local South Bend
Lathe Co. dealer. If you do not have a dealer in
your area, please call us at (360) 734-1540 or
email us at cs@southbendlathe.com.
SB1268—Collet Attachment 5–C for SB1012,
SB1013, SB1014, SB1015, SB1037 & SB1038
Lathes
SB1269—Taper Attachment for SB1012,
SB1013, SB1014, SB1015, SB1037 & SB1038
Lathes

For Machines Mfg. Since 7/09

SB1239—MT#4 High Performance Live Center
South Bend® brand live centers are the best centers in the industry made with pride and uncompromising quality.
s

s
s
s
s

3HAFTS ARE MADE OF ALLOY STEEL AND VACUUM
heat treated to HRC60 ± 1 for high rigidity
and durability.
#ENTERS USE A COMBINATION OF ROLLER BEARINGS
thrust ball bearings and ball bearings.
!PPLICABLE FOR #.# LATHES AND HIGH SPEED
turning.
7ATERPROOF DESIGN
CENTERS

SB1268

8.86"
1.73"

SB1269

2.83"

4.29"

2.99"
1.378"
60°

Figure 103. Model SB1239 High Performance Live
Center.
Figure 102. Collet and taper attachments accessories.

High-Precision 3-Jaw Scroll Chucks

SB1266—8" Backplate D1-6 for SB1012 &
SB1013 Lathes

SB1307—6" 2-Pc. Plain-Back 1.772" Bore
SB1308—7" 2-Pc. Plain-Back 2.283" Bore
SB1309—8" 2-Pc. Plain-Back 2.283" Bore
SB1310—9" 2-Pc. Plain-Back 2.756" Bore
SB1311—10" 2-Pc. Plain-Back 3.504" Bore
SB1312—12" 2-Pc. Plain-Back 4.134" Bore

SB1267— 10" Backplate D1-6 for SB1014,
SB1015, SB1037 & SB1038 Lathes
SB1313—6" 4-Jaw Scroll Chuck Plain-Back w/2Pc. Jaws 1.772" Bore
SB1313—6" Adjustable 4-Jaw Chuck
All-Steel Body w/2-Pc. Jaws and 1.654" Bore
-52-

ACC ESSOR I ES

For Machines Mfg. Since 7/09

SB1247—MT4 Bull Nose Center
s #R -O STEEL HARDENED TO (2# Ò
s 4APER ROLLER BALL BEARING CONSTRUCTION
s 'REAT FOR TURNING PIPES

1.81"

6.73"

EVS Toolroom Lathes

SB1298—SBL Bench Lathe Shop Clock
SB1299—SBL Toolroom Lathe Shop Clock
SB1300—SBL Lathe with Man
These fine traditional shop clocks are constructed
with a metal antique-finished frame. They are
easy to read from a distance and measure 14"
in diameter. Pictures just don't do them justice.
They are very nice quality clocks and perfect for
the South Bend Lathe aficionado.

SB1298

SB1299

4.25"
0.67"

2.48"
0.47"

SB1300
60°

Figure 104. SB1247 MT4 Bull Nose Center.

Figure 106. Antique-finished South Bend shop clocks.

SBL Gearhead T-Shirt
SBL One Good Turn T-Shirt
100% Cotton, preshrunk T-shirts, available in
sizes S, M, L, XL, 2XL, 3XL.

SB1279—10 Pc. Precision 5–C Collet Set
Set of 10 collets sized from 1⁄8" - 3⁄4". Same quality
as the individual collets, only packaged in one
convenient set.

Figure 105. Model SB1279 10 Pc. 5-C Collet Set.

Figure 107. Official South Bend Lathe T-Shirts.

-53-

EVS Toolroom Lathes

MAINTENANCE

For Machines Mfg. Since 7/09

MAINTENANCE

Maintenance Schedule

Always disconnect power
to the machine before
performing maintenance.
Failure to do this may
result in electrocution or
accidental startup injury.

Daily, During Operations
s
s
s

Daily, After Operations
s
s

Each operator of this machine is responsible
for ensuring proper care of the equipment. We
strongly recommend all operators make a habit
of following the daily maintenance procedures.
For optimum performance from this machine,
this maintenance schedule must be strictly
followed. Use the chart provided on Page 55 to
ensure this is done.

s
s
s
s

,OOSE MOUNTING BOLTS OR FASTENERS
7ORN FRAYED CRACKED OR DAMAGED WIRES
'UARDS REMOVED
%MERGENCY STOP BUTTON NOT WORKING CORRECTLY
or not requiring you to reset it before
starting the machine again.
! REDUCTION IN BRAKING SPEED OR EFFICIENCY
(EADSTOCK OIL NOT FLOWING AGAINST SIGHT GLASS
#UTTING FLUID NOT FLOWING OUT
Any other unsafe condition.

Daily, Before Operations
s
s
s
s
s
s
s
s
s
s

-54-

#HECKADD GEARBOX OIL Page 58).
#HECKADD APRON OIL Page 58).
#HECK CUTTING mUID LEVEL Page 62).
,UBRICATE THE WAYS Page 59).
0UT OIL IN THE BALL OILERS Page 60).
#HECKADD LEADSCREW FEEDROD BEARING OIL
(Page 59).
#LEANLUBRICATE THE LEADSCREW Page 59).
4URN SPINDLE SPEED DIAL ALL THE WAY DOWN
-OVE THE POWER FEED LEVER ON THE APRON TO
neutral (to prevent crashes upon startup).
%NSURE CARRIAGE LOCK BOLT IS LOOSE

6ACUUMCLEAN ALL CHIPS AND SWARF FROM BED
slides, and chip drawer.
7IPE DOWN ALL UNPAINTED OR MACHINED
surfaces with an oiled rag (Page 59).
$EPRESS EMERGENCY STOP BUTTON AND SHUT
OFF the main power switch (to prevent
accidental startup).

Monthly
s
s

Ongoing
To maintain a low risk of injury and proper
machine operation, if you ever observe any of the
items below, shut down the machine immediately
and fix the problem before continuing operations:

6ERIFY HEADSTOCK OIL mOWS WHEN POWER IS
turned ON (Page 56).
6ERIFY ELECTRICAL BOX COOLING FAN IS OPERATING
6ERIFY HEADSTOCK OIL TEMPERATURE IS UNDER
170° F.

$RAIN AND CLEAN THE CUTTING mUID TANK THEN
add new cutting ﬂuid.
2EMOVE ELECTRICAL BOX AIR lLTER AND CLEAN
with compressed air or a vacuum.

Annually (or Semi-Annually with Hard Use)
s
s
s

$RAIN AND CLEAN THE HEADSTOCK OIL RESERVOIR
then add new oil.
#HANGE THE APRON OIL
#HANGE THE GEARBOX OIL

Cleaning
Regular cleaning is one of the most important
steps in taking care of this lathe. We recommend
that each operator be responsible for cleaning the
machine immediately after using it or at the end
of the day. We also recommend that the cleaning
routine be planned into the workflow schedule,
so that adequate time is set aside to do the job
right.
Typically, the easiest way to clean swarf from
the bed ways and chip drawer is to use a wet/dry
shop vacuum that is dedicated for this purpose
only. The small chips leftover after vacuuming
can be wiped up with a slightly oiled rag. Avoid
using compressed air to blow off chips, as it may
drive them deeper into moving surfaces and
could cause sharp chips to fly into your face or
hands.
All visible swarf should be removed from the
lathe during cleaning.

Day

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

See owner’s manual for more information regarding cutting ﬂuid condition, replacement, disposal, and safety.

Change Headstock Oil
Change Apron Oil

Date of last annual service:

Date of next annual service:

Make copies of this page to use each month. Keep each chart as a maintenance record for your South Bend Lathe.

Change Gearbox Oil

Service Item

Once every year, or more often with heavy use,
perform these service items. Keep track of when you
last performed your annual service and when you’ll
need to perform it again.

s &!8
www.southbendlathe.com

MAINTENANCE

Annual Service

Use this chart to keep track of the maintenance performed on your South Bend Lathe. Cross out or initial the “Day” box for each item on the list.
If the box is blacked out, maintenance is not required for that item on that day. Use the maintenance poster included with your South Bend Lathe
as a quick reference guide when performing the maintenance items.

Cutting Fluid
Condition

Cutting Fluid
Level

Leadscrew
Bearing
Oil Level

Apron Oil
Level

Gearbox
Oil Level

Headstock
Oil Level

Inspection

Unpainted
Surfaces

Leadscrew

Ball Oilers

Ways

Lubrication

Item

South Bend Lathe Co. Monthly Maintenance Chart for EVS Toolroom Series Lathes

For Machines Mfg. Since 7/09
EVS Toolroom Lathes

Maintenance Chart

-55-

EVS Toolroom Lathes

MAINTENANCE

For Machines Mfg. Since 7/09

Monitoring Oil Temperature

Lubrication
Headstock
Oil Type .. Mobil DTE Light or ISO 32 Equivalent
Oil Amount .............................................. 7.5 Liters
Check/Add Frequency .................................... Daily
Change Frequency ...................................Annually
The headstock lubrication system is the most
important lubrication system on the machine. It
consists of an electric oil pump, a low oil pressure
kill switch, a holding tank, oil lines, and a
distribution manifold. The headstock has a series
of oil lines that direct oil to key locations, such as
the spindle bearings and headstock gearing, to
ensure that they always remain well lubricated.
The oil pump automatically turns ON and begins
oiling the headstock components when the main
power switch is turned ON and the emergency
stop button is reset. The oil is pumped before the
spindle is started to protect the spindle bearings
against potential damage from dry starts.
Checking & Adding Oil
The sight glass on the side of the headstock oil
tank, shown in Figure 109, shows the oil level
and temperature; the bottom line represents the
minimum oil level and the top line represents the
maximum oil level. The lathe must be powered
down and stopped when to get an accurate
reading on the oil level.
Oil Fill Spout

During operations, regularly monitor the oil
temperature shown in the sight glass in Figure
109. The temperature of the headstock oil must
remain under 170° F. or the oil will start to
overheat and break down, causing it to lose its
lubrication properties.
Under normal conditions, the oil should not
reach 170° F.; however, if it does, shut down the
machine and allow the oil to cool. Investigate
why the oil is getting so hot. Possibilities may
be poor ventilation, excessive work loads, poor
oil quality, oil is breaking down (losing lubricity)
due to long term use, or extreme work site
temperatures.
If possible, correct the conditions causing the
oil to get hot. If the oil is old or you suspect it is
of poor quality, change it. If the work loads or
working environment are extreme, reduce the
duty cycle of the lathe to allow the oil to cool
down when it gets hot.
If the oil temperature ever exceeds 170° F.,
change it as soon as possible to make sure the
spindle bearings have high quality lubrication.
Verifying Oil Pump Operation
To prevent costly damage to the headstock gears
and bearings, a kill switch will shut the lathe
down if the oil pump stops working or the oil
level is too low. You can verify that the pump is
working by looking at the sight glass shown in
Figure 109. When working correctly, oil can be
seen ﬂowing across the sight glass.

Sight Glass
Headstock
Oil Tank

Figure 108. Headstock oil tank & components.

Headstock Oil
Sight Glass

When the oil level approaches the minimum line,
add enough oil to bring it up to the maximum
line.
Figure 109. Location of the headstock oil sight glass.

-56-

For Machines Mfg. Since 7/09

MAINTENANCE

Cleaning Pump System & Changing Oil

The headstock oil pump system must be cleaned
and the oil changed after the break-in period and
then annually (or every six months with hard
service or extreme working conditions).

EVS Toolroom Lathes

After the tank is completely cleaned out,
unthread the screen from the bottom of the
pump suction pipe (see Figure 111), and
remove the screen from the tank.

To clean the oil pump system:
1.

DISCONNECT LATHE FROM POWER!

Remove the cap from the fill spout shown in
Figure 110.

Suction
Screen

Fill Spout

Figure 111. Suction screen removal.

Access Cover
Drain Plug

Clean the suction screen thoroughly with
mineral spirits and compressed air.

10. Re-install the suction screen.
Figure 110. Headstock oil tank component locations.

Place at least a 3-gallon drain pan under the
tank and remove the drain plug to empty the
oil into the pan.

Clean away any dust, debris, metal shavings,
or grime from the access cover.

Using a 4mm hex wrench, remove the four
access cover cap screws, then use the cap
screw in the center as a handle and lift off
the access cover.

Put on splash-proof safety glasses, rubber
gloves, and a respirator rated for fumes.

Using mineral spirits and rags, wipe down
the inside of the tank to clean it. Make sure
to soak up any excess mineral spirits with a
dry rag, so it does not stay in the tank.

Tip: Consider placing one or two magnets at the
bottom of the tank to collect any fine metal
particles generated by the headstock drive
train. This will make cleaning easier the
next time around and ensure that more
metal particles are kept out of the headstock
oil.
11. Re-install the drain plug.
12. Refill the tank with oil (refer to Page 56 for
the recommended type and amount of oil to
use).
13. Replace the fill spout plug.

-57-

EVS Toolroom Lathes

MAINTENANCE

For Machines Mfg. Since 7/09

Gearbox

Apron

Oil Type ...... Mobil Vactra 2 or ISO 68 Equivalent
Oil Amount ...................................................1 Liter
Check/Add Frequency .................................... Daily
Change Frequency ...................................Annually

Checking & Adding Oil

The sight glass shown in Figure 112 shows the
oil level in the gearbox. At the maximum level,
the oil ﬁlls approximately 3⁄4 of the sight glass.
At the minimum level, the oil only ﬁlls 1⁄4 of the
sight glass. Check the oil level daily. When the
oil approaches the minimum level, add enough
oil to bring it up to the maximum level.

The sight glass shown in Figure 114 shows the
oil level in the apron. At the maximum level, the
oil ﬁlls approximately 3⁄4 of the sight glass. At the
minimum level, the oil only ﬁlls 1⁄4 of the sight
glass. Check the oil level daily. When the oil
approaches the minimum level, add enough oil to
bring it up to the maximum level. This oil is also
used by the way pump to lubricate the ways and
slides.

Gearbox Oil
Sight Glass

Sight Glass

Drain Plug
Figure 114. Location of apron drain plug & sight glass.
Figure 112. Gearbox sight glass location.

Changing Oil
Changing Oil
The gearbox oil must be changed after the
break-in period and then annually (or every six
months with hard service or extreme working
conditions). Figure 113 shows fill and drain
plugs used when changing the gearbox oil.

The oil in the apron reservoir must be changed
after the break-in period and then annually (or
every six months with hard service or extreme
working conditions). The drain plug is shown in
Figure 114 and the fill plug is shown in Figure
115.
Fill Plug

Gearbox Oil
Fill Plug

Gearbox Oil
Drain Plug
Figure 113. Location of gearbox fill and drain plugs.

-58-

Figure 115. Location of fill plug for apron oil reservoir.

For Machines Mfg. Since 7/09

MAINTENANCE

EVS Toolroom Lathes

Lead Screw & Feedrod Bearings

Ways & Slides

Oil Type ...... Mobil Vactra 2 or ISO 68 Equivalent
Oil Amount ...................................................1 Liter
Check/Add Frequency .................................... Daily

The way pump shown in Figure 117 lubricates
the saddle and cross slide way guides with the oil
from the apron reservoir.

Checking & Adding Oil

To use the way pump to lubricate the ways, pull
the pump knob out for two or three seconds and
then push it in. The pump draws oil from the
apron reservoir and then forces it through drilled
passages to the way guides.

To check the oil level, remove the fill plug and
look inside the reservoir (Figure 116). The oil
level must remain full to keep the leadscrew
bearing adequately lubricated. Pour oil in the
reservoir until it is as full as possible without
overflowing.

Leadscrew

Fill Plug

Repeat this process and move the carriage left/
right and the cross slide forward/backward to
distribute oil along the way guides.
Lubricate the guides once before and once after
operating the lathe. If the lathe is in a moist
or dirty environment, increase the lubrication
interval and make sure to keep the oil level full.
Fill Plug

Oil Reservoir
for Feedrod
& Leadscrew
Bearings

Way
Pump

Figure 116. Leadscrew lubrication.

Lead Screw
Oil Type ...... Mobil Vactra 2 or ISO 68 Equivalent
Oil Amount ............................................ As Needed
Lubrication Frequency................................... Daily
Before lubricating the leadscrew (Figure 116),
clean it first with mineral spirits. A paint brush
works well to help clean out the threads. Make
sure to move the carriage out of the way, so you
can clean the entire length of the leadscrew.
Apply oil along the length of the leadscrew. Use
a paint brush to make sure the oil is evenly
applied and down in the threads.

Sight Glass
Figure 117. Location of way pump, fill plug, and sight
glass on the apron.

Unpainted & Machined Surfaces
Besides the ways and leadscrew, all other
unpainted and machined surfaces should be
wiped down daily to keep them rust-free and in
top condition. This includes the top of the saddle,
the cross slide, compound slide, tool post, chuck,
feedrod, and any other surface you can ﬁnd that
could be vulnerable to rust if left unprotected
(this especially includes any parts that may be
exposed to water soluble cutting ﬂuids). Typically
with these parts, a thin ﬁlm of oil is all that
is necessary for protection. Any quality metal
protectant can be used to protect machined
surfaces, including either of the oils you use
elsewhere in the lathe.

-59-

EVS Toolroom Lathes

MAINTENANCE

For Machines Mfg. Since 7/09

Ball Oilers

Cleaning Electrical Box Filter

Oil Type .. Mobil DTE Light or ISO 32 Equivalent
Oil Amount ..........................................1 or 2 Drops
Lubrication Frequency................................... Daily

The door of the electrical box contains an air
filter (Figure 120) to prevent dust from entering
the box as the cooling fan pulls in cool air to
reduce heat.

This lathe has ﬁve ball oiler locations (see
Figures 118–119) that should be oiled on a daily
basis. In order to properly squirt oil into the ball
oiler mechanisms, you will need an oil can or
gun.

The air filter should be cleaned on a monthly
basis to ensure proper air circulation in the
electrical box. A clogged air filter will not allow
the cooling fan to do its job, which could result in
a decreased lifespan of the electrical components.

Cooling Fan
Filter
Figure 118. Ball oiler locations.

Figure 120. Electrical box cooling fan and filter.

To clean the ﬁlter:
1.

DISCONNECT LATHE FROM POWER!

Put on a dust mask or respirator to reduce
your risk of inhaling fine dust.

Open the electrical box door, and remove the
electrical box air filter.

Use compressed air to blow dust out of the
filter. Make sure to blow the dust from the
clean side (the side facing inward) of the
filter so you do not drive dust farther into
the filter.

Re-install filter and close electrical box door.

Figure 119. Tailstock ball oiler locations.

To lubricate the ball oilers, clean the outside
surface to remove any dust or grime, push the
ball with the tip of the oil can nozzle, and squirt
a small amount inside. If the lathe is in a moist
or dirty environment, increase the oiling interval.

-60-

For Machines Mfg. Since 7/09

MAINTENANCE

EVS Toolroom Lathes

End Gearing

Lubricating

Grease Type ............................................... NLGI#2
Frequency ................ Annually or When Swapping

DISCONNECT LATHE FROM POWER!

Remove the headstock side cover and all the
end gears shown in Figure 121.

Clean the end gears thoroughly with mineral
spirits to remove all the old grease. Use a
small brush if necessary to clean between
the teeth.

Clean the shafts from which the end gears
were removed, and wipe up any old grease
splatters in the vicinity and on the inside of
the headstock cover.

With clean hands, apply a thin layer of
grease on the gears. Make sure to get grease
between the gear teeth, but not so much that
it ﬁlls the voids between the teeth.

Install the end gears and mesh them
together with an approximate backlash of
0.005". Once the gears are meshed together,
apply a small dab of grease in the crux of
where the gears mesh together—this grease
will spread around when the gears start
moving and re-coat any areas scraped off
during installation.

The end gears, shown in Figure 121, should
always have a thin coat of heavy grease to
minimize corrosion, noise, and wear. Care must
be taken to avoid over-greasing because excess
grease may be ﬂung onto the V-belts, which will
reduce optimal power transmission from the
motor.

End
Gears

Figure 121. Location of end gears that require grease.

Handling & Care
Make sure to clean and lubricate any gears you
install or swap. Unless you are very careful
during handling and storage, the coating of
grease on the gears will easily pickup dirt or
debris, which can then spread to the other gears
and increase the rate of wear.
Make sure the cover remains installed whenever
possible to keep the gears free of dust or debris
from the outside environment.

Annual Maintenance
Once a year, remove all the end gears, clean
them thoroughly, and apply a new coating of
grease. Even if the headstock side cover has
been kept in place throughout the year, it is still
possible for dust from the V-belts to build-up
in the grease, and the grease may also start to
break down with extended or heavy use.

-61-

MAINTENANCE

EVS Toolroom Lathes

Cutting Fluid System
The cutting fluid system consists of a fluid tank,
pump, and flexible nozzle. The pump pulls fluid
from the tank and sends it to the valve, which
controls the flow of cutting fluid to the work
area. When the valve is opened or closed, the
fluid comes out of the nozzle and drains through
the chip drawer and into the catch tray and
then into the tank where it is picked up again
by the pump. Figure 122 shows many of these
components and their locations.
Pump Switch

Nozzle
Valve

For Machines Mfg. Since 7/09

Hazards
As some cutting fluid ages, dangerous microbes
can proliferate and create a biological hazard.
The risk of exposure to this hazard can be greatly
reduced by replacing the old cutting fluid on a
monthly basis, as indicated in the maintenance
schedule.
The important thing to keep in mind when
working with the cutting fluid is to minimize
exposure to your skin, eyes, and respiratory
system by wearing the proper PPE (personal
protective equipment), such as splash-resistant
safety glasses, long-sleeve gloves, protective
clothing, and a NIOSH approved respirator.

BIOLOGICAL & POISON
HAZARD!
Use the correct personal
protection equipment
when handling cutting
fluid. Follow federal, state,
and fluid manufacturer
requirements for proper
disposal.

Adding Fluid
1.

DISCONNECT LATHE FROM POWER!

Remove the vented cover and slide the tank
out, as shown in Figure 123.

Catch Tray
Pump & Tank Behind
this Vented Cover

Chip
Drawer

Figure 122. Cutting fluid system components and
locations.

Although most swarf from machining operations
falls into the chip tray and stays there, some
small chips drain into the tank. The pump uses
a screen to prevent it from picking up the small
swarf that ends up in the tank.

Tank
Pump Motor

Since the swarf is spread throughout the coolant
system, cleaning the system on a regular basis is
a requirement to maintain the life of the pump.

-62-

Figure 123. Cutting fluid pump and tank.

Pour cutting fluid in the tank until it is
nearly full.

Slide the tank back into the base and replace
the vented cover.

For Machines Mfg. Since 7/09

MAINTENANCE

Changing Cutting Fluid
When you replace the old cutting fluid, take the
time to thoroughly clean out the chip drawer,
catch tray, and chip tray. The entire job only
takes about a 1⁄2 hour when you are prepared
with the proper materials and tools. Make
sure to dispose of all old fluid according to local
regulations.

Items Needed:

Note: The electrical conduit was purposely left
long, so the tank can be removed without
disconnecting wires from the pump. Do not
disconnect electrical lines.
Fluid Hose

Qty

Safety Wear ......See Hazards section on Page 62
New Cutting Fluid .................................. 3 Gallons
Empty 5 Gallon Bucket w/Lid .............................. 2
Phillips Screwdriver #2 ........................................ 1
Wrench 3⁄4" ............................................................. 1
Disposable Shop Rags ................. Approximately 6
Hose or Tubing 5⁄8" x 60" (optional) ............ 1 Piece
Magnets (optional) ................ As Many As Desired

To change the cutting ﬂuid:

Disconnect
Here if
Necessary

Figure 124. Fluid hose that may need to be
disconnected in order to remove tank for cleaning.

Pour out the remaining cutting fluid into
your 5-gallon bucket and close the lid.

Wipe up the layer of swarf/residue on the
bottom of the tank and put the waste in the
second 5-gallon bucket. Flush out the tank
with soapy water and drain into the second
5-gallon bucket.
Slide the tank partially into the base and
reconnect fluid hose (if removed).

Position the coolant nozzle over the splash
guard, so it is pointing behind the lathe. If
you have the optional hose, connect it to the
end of the coolant nozzle now.

Place the 5-gallon bucket behind the lathe
and underneath the coolant nozzle. If you
have the optional hose, place the hose in the
bucket. Otherwise, you may need to hold the
bucket up to the coolant nozzle to prevent
coolant from splashing outside of the bucket.

Turn the cutting fluid pump ON (or have
another person turn it ON if you are holding
the bucket), and pump the old cutting
fluid out of the tank. Turn the pump OFF
immediately after fluid stops flowing.

EVS Toolroom Lathes

Tip: Leave one or more magnets at the bottom
of the tank to collect metal chips and make
cleanup easier next time.
Refill the tank with new cutting fluid, then
slide the tank completely into the base.

10. CONNECT LATHE TO POWER.
11. Open the valve on the cutting fluid nozzle.

Running the pump without adequate fluid in
the tank may permanently damage it. This is
abuse and not covered by the warranty.
4.

DISCONNECT LATHE FROM POWER!

Remove the vented cover shown in Figure
122 and slide the tank half way out of the
base, as shown in Figure 123.

12. Turn the cutting fluid pump ON to verify
that fluid cycles properly, then turn it OFF.
Note: It may take a few seconds for the pump to
start circulating fluid; however, if fluid does
not start coming out within the first minute,
turn the pump OFF so you do not burn out
the pump motor. Try priming the pump
manually by pour cutting fluid down into the
nozzle, then repeat Step 13.

— If necessary, disconnect ﬂuid hose from
pump, where shown in Figure 124.
-63-

EVS Toolroom Lathes

MAINTENANCE

For Machines Mfg. Since 7/09

Machine Storage

To prepare your machine for long-term storage (a
year or more):

If the machine is not properly prepared for
storage, it may develop rust or corrosion. If
decommissioning this machine, use the steps
in this section to ensure that it remains in good
condition for later use.

To prepare your machine for short-term
storage (up to a year):
1.

Pump out the old cutting fluid, and flush the
lines and tank with warm, soapy water.

DISCONNECT LATHE FROM POWER!

Thoroughly clean all unpainted, bare metal
surfaces, then apply a liberal coat of way oil.

Lubricate the machine as outlined in the
lubrication section.

Cover and place the machine in a dry area
that is out of direct sunlight and away from
hazardous fumes, paint, solvents, or gas.
Fumes and sunlight can bleach or discolor
paint and make plastic guards cloudy.

Once or twice a month, depending on the
ambient humidity levels in the storage
environment, wipe down the machine as
outlined in Step 3.

Every few months, start the machine
and run all gear-driven components for a
few minutes. This will keep the bearings,
bushings, gears, and shafts well lubricated
and protected from corrosion, especially
during the winter months.

-64-

Run the lathe for 10 minutes to bring the
gearboxes to operating temperature, then
drain and refill the all gearboxes with fresh
oil.

Note: During extended storage (more than two
years), any component above the oil level
may rust from condensation. We recommend
overfilling any sealed gearbox. However, over
time there will be some seepage around some
shafts and seals. If any gearbox is overfilled
make sure to put a tag on the controls as
a reminder for the maintenance person
to correct the oil level before starting the
machine. If a gearbox cannot be overfilled,
every few months manually rotate the shaft
or spindle to coat any exposed gears with oil.
2.

Pump out the old cutting fluid, and flush the
lines and tank with warm, soapy water.

DISCONNECT LATHE FROM POWER!

Thoroughly clean all unpainted, bare metal
surfaces, then apply a liberal coat of way oil,
a heavy grease, or rust preventative. Take
care to ensure these surfaces are completely
covered but that the rust preventative or
grease is kept off of painted surfaces.

Lubricate the machine as outlined in the
lubrication section.

Loosen or remove machine belts so they do
not become stretched during the storage
period. (Be sure to also affix a maintenance
note near the power button as a reminder
that the belts have been loosened or
removed.)

Place a few moisture absorbing desiccant
packs inside of the electrical box.

For Machines Mfg. Since 7/09

SERVICE

EVS Toolroom Lathes

Backlash Adjustment

Cross Slide Leadscrew

Backlash is the amount of free play felt
while switching rotation directions with
the handwheel. This can be adjusted on the
compound and cross slide leadscrews.

Hex Wrench 3mm ................................................. 1
Hex Wrench 5mm ................................................ 1

Reducing backlash to less than 0.001"
is impractical. Avoid the temptation to
overtighten the backlash set screw while
adjusting. Overtightening leads to accelerated
wear of the wedge, nut, and leadscrew.

Compound Leadscrew
Tools Needed:

Qty

Hex Wrench 3mm ................................................. 1
Backlash is adjusted by tightening the set screws
shown in Figure 125. When these screws are
adjusted against the leadscrew nut, they offset
part of the nut to remove play between the nut
and leadscrew.
If you end up adjusting the nut too tight, loosen
the set screws, tap the compound a few times
with a rubber or wooden mallet, and turn the
handle slowly back and forth until it moves
freely.

Tools Needed:

Qty

Backlash is adjusted by loosening all four
cap screws shown in Figure 126, and then
tightening the center set screw, which pushes
down on a wedge and forces the nut apart, taking
up lash in the nut and leadscrew.
If you end up adjusting the nut too tight, loosen
the set screw, tap the cross slide a few times with
a rubber or wooden mallet, and turn the handle
slowly back-and-forth, until the handle turns
freely.
To re-adjust the backlash, rock the handle back
and forth and tighten the set screw slowly until
the backlash is at approximately 0.001" as
indicated on the handwheel dial.
Cap Screw

Set
Screw

To readjust the backlash, rock the handle back
and forth, and tighten the screws slowly until the
backlash is at approximately 0.001" as indicated
on the handwheel dial.
Figure 126. Cross slide backlash adjustment screws.

Set Screws

Figure 125. Compound slide backlash adjustment set
screws.

-65-

EVS Toolroom Lathes

SERVICE

Leadscrew End Play
Adjustment

Gib Adjustment

After a long period of time, you may find that the
leadscrew develops a small amount of end play.
This lathe is designed so that leadscrew end play
can be easily removed with adjustment.

Tools Needed:

For Machines Mfg. Since 7/09

Qty

Open End Wrench 1" ............................................ 1
Hex Wrench 3mm ................................................. 1
Hex Wrench 5mm ................................................ 1
To remove leadscrew end play:
1.

DISCONNECT LATHE FROM POWER!

Remove the three cap screws and end cover.

Loosen both retaining nut set screws shown
in Figure 127.

Leadscrew

Retainer
Nut with Set
Screws

The goal of adjusting the cross slide, tailstock,
saddle, and compound gib screws is to remove
sloppiness in the ways without over-adjusting
them to the point where the slides become stiff
and difficult to move.
In general, loose gibs cause poor finishes and
tool chatter; however, over-tightened gibs cause
premature wear on the slide, leadscrew, and nut,
and are difficult to operate.
The gibs are tapered and held in position by a
screw at each end. To adjust the gib, turn one
screw a 1⁄4 turn clockwise and the other screw a
1
⁄4 turn counterclockwise, so both screws move
toward the same direction. Now test the feel of
the sliding component by turning the handwheel,
and adjust the gib screws as necessary to make it
tighter or looser.
The gib adjustment process usually requires
some trial-and-error. Repeat the adjustment
process as necessary until you find the best
balance between loose and stiff movement. Most
machinists find that the ideal gib adjustment is
one where a small amount of drag or resistance
is present yet the handwheels are still easy to
move.
Figures 128–131 show the location of the screws
for each gib on this machine.

Figure 127. Leadscrew end play adjustment.

Engage the half nut lever.

Rotate the carriage feed handwheel back
slightly and tighten the retaining nut at the
same until the end play is removed.

Tighten both set screws and re-install the
cover.

-66-

Compound
Front Gib
Screw

Cross
Slide
Front
Gib
Screw

Figure 128. One of two cross slide and compound gib
screws.

For Machines Mfg. Since 7/09

SERVICE

EVS Toolroom Lathes

Half Nut Adjustment
The half nut mechanism can be tightened if it
becomes loose from wear. The pressure exerted
by the half nut is controlled by a gib similar to
the one in the saddle, which is on Page 66. The
half nut gib is adjusted with two set screws.

Tool Needed:

Qty

Hex Wrench 3mm ................................................. 1
Gib
Screw

To adjust the half nut:

Figure 129. One of two rear saddle gib screws.

Disengage the half nut.

Remove the thread dial.

Turn the two half-nut adjustment set screws,
shown in Figure 132, clockwise about an 1⁄8th
of a turn.
Leadscrew

Left Gib
Screw

Half Nut
Adjustment Set
Screws
(Thread Dial
Removed)

Figure 130. One of two front saddle gib screws.

Half Nut

Right Gib Screw

Figure 132. Half nut gib adjustment.

Engage/disengage the half nut several times
and notice how it feels (you may need to
move the carriage handwheel slightly to get
the half nut to close).
The half nut is correctly adjusted when it
has a slight drag while opening and closing.
The movement should not be too stiff or too
sloppy.

Figure 131. One of two tailstock gib screws.

Repeat Steps 3–4, if necessary, until you are
satisﬁed with the half nut adjustment. (If
the half nut becomes too stiff, turn the set
screws counterclockwise to loosen it.

Re-install the thread dial.

-67-

SERVICE

EVS Toolroom Lathes

Feedrod Clutch
Adjustment

Insert the hex wrench into the collar
adjustment hole shown in Figure 135, and
use the wrench to rotate the clutch collar.
— If you need to increase the release point,
rotate the clutch collar upward.

This lathe has an adjustable feed clutch that
helps protect the drivetrain from overload.
The feed clutch release point is adjusted at
the factory. However, it can be easily adjusted
depending on operator requirements.

Tools Needed:

For Machines Mfg. Since 7/09

— If you need to decrease the release point,
rotate the clutch collar downward.

Qty

Phillips Screwdriver #2 ........................................ 1
Hex Wrench 3mm ................................................. 1

To adjust the clutch release point:
1.

DISCONNECT LATHE FROM POWER!

Remove the front and side feed access covers,
as shown in Figure 133.

Collar
Adjustment Hole
Set Screw
Slot
Figure 135. Feed clutch set screw alignment.

Line up the set screw hole in the clutch
collar with the closest set screw slot that is
cut into the feedrod (see Figure 135).

Install and tighten the set screw so it is fully
seated in the slot.

Re-install both access covers.

Feed Access Cover

Figure 133. Feed access covers removed.

Remove the clutch collar set screw, as shown
in Figure 134.

Figure 134. Removing set screw from clutch collar.

-68-

SERVICE

For Machines Mfg. Since 7/09

EVS Toolroom Lathes

V-Belts

Brake & Switch

V-belts stretch and wear with use, so check them
on a monthly basis to ensure optimal power
transmission. Replace all of the V-belts if any of
them show signs of glazing, fraying, or cracking.

Phillips Screwdriver #2 ........................................ 1
Open End Wrench 24mm...................................... 1

As the brake lining wears, the foot pedal
develops more travel. If the brake band is not
adjusted to compensate for normal wear, the
limit switch will still turn the lathe off, but the
spindle will not stop as quickly. It is especially
important that the brake is kept properly
adjusted so you can quickly stop the spindle in
an emergency.

To adjust the V-belts:

Tools Needed:

Qty

DISCONNECT LATHE FROM POWER!

Remove the cover shown in Figure 136.

Motor Cover

Figure 136. Location of motor cover.

Turn the hex nuts on the motor mount bolts
shown in Figure 137 to move the motor
mount plate up or down and adjust the
V-belt tension. When correctly tensioned,
each belt should have about 3⁄4" deflection
when pressed firmly (see Figure 137).
Motor Mount Bolts

Qty

Phillips Screwdriver #2 ........................................ 1
Hex Wrench 6mm ................................................. 1
To adjust the brake and brake switch:
1.

DISCONNECT LATHE FROM POWER!

Put on a respirator and eye protection to
protect yourself from hazardous brake dust.

Remove the motor cover shown in Figure
137.

Measure the remaining brake band lining at
the thinnest point, which is usually at the 8
o'clock position, as shown in Figure 138.

3mm

Pulley
Deflection
Figure 138. Minimum brake band lining thickness.

Pulley
Figure 137. V-belt adjustment.

Firmly tighten the hex nuts (loosened in the
previous step) against the motor mount plate
to prevent it from moving out of adjustment
during operation, then re-install the motor
cover.

When the brake band is new, the lining
is approximately 6mm thick. If the lining
thickness wears to 3mm or less, the brake
band must be replaced; otherwise, the rivets
that secure the lining to the band will soon
grind into the brake hub. If the hub becomes
damaged, it must be replaced, which will
substantially increase the cost of repair,
compared to just replacing the brake band.

-69-

SERVICE

EVS Toolroom Lathes
5.

Remove pedal stop shown in Figure 139.

Move the brake band to the right one hole,
and re-install the pedal stop, tightening it
until it is just snug.

For Machines Mfg. Since 7/09

Pedal Stop

— If installing a new brake band, install the
cap screw so there is one hole to the left
for future brake adjustment.

Move Brake Band to the
Right to Adjust Brake

Pedal Lever

Cap Screw

Move Pedal Stop Left or Right to
Adjust Foot Pedal Height.
Figure 139. Brake linkage adjustments.
Pedal
Lever
25mm

Plunger
and
Cam Lobe

Motor Kill
Switch

Figure 141. Motor kill switch.
Pedal Stop

Figure 140. Pedal travel adjustment.

Firmly push the pedal lever (Figure 140) to
the right until it stops and the brake band is
fully clamped around the brake hub.

Tap the pedal stop into position so there
is approximately a 25mm gap between the
pedal lever and the stop (see Figure 140).

Tighten the cap screw on the pedal stop.

10. Locate the motor kill switch (shown in
Figure 141) at the tailstock end of the lathe.

-70-

11. Push the pedal lever down to verify that the
cam lobe pushes the kill switch plunger in.
When pushed in, the switch should click.
— If the switch does not click, loosen the
switch mounting screws, push the pedal
all the way down, and move the switch
closer to the lobe until it clicks. Secure the
switch in place at this location.
— In the released position, there should be
an approximate 3mm gap between the
plunger roller and the lobe.
12. Re-install the cover, test the brake operation.

SERVICE

For Machines Mfg. Since 7/09

Leadscrew Shear Pin
Replacement

EVS Toolroom Lathes

Rotate the shroud washer so the cutout lines
up with the shear pin head, as shown in
Figure 144.
Shroud Washer

Shear Pin
Head

9mm

3mm

5.8mm

7mm

0.5mm
0.2mm

Cutout

0.2mm

NOTE: Shear Pin Material = S45C (SAE 1045)
Figure 144. Shroud washer/pin alignment.
Figure 142. Shear pin specifications.

Tools Needed:

Qty

Phillips Screwdriver #2 ........................................ 1
External Retaining Ring Pliers #1 ....................... 1
Magnet ................................................................... 1
Safety Glasses ....................................................... 1

To replace the shear pin:
1.

DISCONNECT LATHE FROM POWER!

Remove the front and side feed access covers,
as shown in Figure 143.

Put on safety glasses.

Remove the retaining ring from its groove
and place it in the rear-most position away
from the shroud washer.

Move the shroud washer away from the
shear pin (to the rear position), as shown in
Figure 145, so there is enough of a gap to
remove the shear pin.

Rear
Position

Feed Access Cover

Gap
Figure 145. Shear pin access.

Figure 143. Feed access covers removed.

-71-

EVS Toolroom Lathes

SERVICE

Use the magnet to remove the shear pin
head, then rotate the lathe spindle to line
up the inner and outer bores, as shown in
Figure 146. Next, use the magnet to remove
the other half of the broken shear pin when
it becomes visible.

Inner Bore

Outer Bore

For Machines Mfg. Since 7/09
Instead, take the time to carefully line
up the two bores. You may ﬁle a slight
chamfer on the end of the pin to make it
easier to insert.

10. With the pin completely seated in the bore
and the head flush with the leadscrew
shoulder, slide the shroud washer against
the shoulder, then rotate the washer 180°
until it covers the head of the shear pin, as
shown in Figure 148.
Rotate
Washer
Slot 180°

Figure 146. Aligned shear pin bores.

Insert a blow gun tip into the shear pin hole,
blow out the hole with compressed air, and
put a drop of oil in the hole.

Insert the new shear pin into the bore, as
shown in Figure 147.

Figure 148. Shroud washer positioning.

New Pin

11. Using retaining ring pliers, return the
retaining ring to its groove, and position
the retaining ring ears over the shear pin
head, as shown in Figure 149, to prevent
the shear pin from falling out—if the shroud
washer rotates into alignment with the pin
access groove lines.

Figure 147. New shear pin installed in bore.

— If the pin does not freely slide into the
bore, DO NOT hammer on the pin or
you may permanently damage the shear
mechanism and bore, making it nearly
impossible to remove and install a new
shear pin later.

-72-

Figure 149. Retaining ring positioned with ears in
front of pin access groove, so pin cannot fall out.

12. Re-install the access covers.

SERVICE

For Machines Mfg. Since 7/09

Gap Removal &
Installation
A portion of the lathe bed directly under the
spindle, the gap insert (Figure 150), can be
removed to create additional space for turning
large diameter parts.
The gap insert was installed, then ground flush
with the bed at the factory to ensure precise fit
and alignment. Therefore, if the gap insert is
removed, it may be difficult to re-install with the
same degree of flushness and accuracy as when
installed at the factory.

Gap Insert

Remove the two way end cap screws and way
set screws shown in Figure 151.

Tighten the two dowel pin jack nuts (Figure
151) until the pins are pulled free from the
gap insert.

Tap the outside of the gap insert with a dead
blow hammer to loosen, then remove it.

To re-install the gap:
1.

Use mineral spirits and a clean lint-free rag
to clean the mating surfaces of the gap, bed,
and ways. If necessary, stone the mating
surfaces to remove scratches, dings, or burrs.

Wipe a thin layer of light machine oil on the
mating surfaces.

Place the gap insert into the gap and use a
block of wood or dead-blow hammer to align
the insert with the lathe bed.

Back off the dowel pin jack nuts, and tap the
dowel pins back into their respective holes
until seated. This process will further help
align the gap insert and bed mating surfaces.

Install all fasteners (except the way set
screws) and lightly snug them in place.

Mount a base-mounted dial indicator to the
top of the saddle to indicate alignment. First
test the peak of the two prisms the saddle
rides on, then test the flanks of the prisms.
Jack the insert up or down by tightening or
loosening the gap bed cap screws.

Alternately tighten the fasteners and tap the
side of the gap insert into alignment.

Inspect the gap position 24-hours later to
make sure the gap is still aligned, adjust
if necessary, then install the two way set
screws.

Figure 150. Gap insert that can be removed from bed.

Tools Needed:

Qty

Hex Wrenches 4, 6, 8mm .............................1 Each
Wrench 17mm ....................................................... 1

To remove the gap:
1.

Remove the four gap bed cap screws, shown
in Figure 151, that secure the gap insert to
the bed.
Dowel Pin
Jack Nut

Gap Bed
Cap Screw

Way End
Cap Screw

EVS Toolroom Lathes

Way Set
Screw
Figure 151. Fasteners holding gap in place.

-73-

EVS Toolroom Lathes

TROU B LESHOOTI NG

For Machines Mfg. Since 7/09

TROUBLESHOOTING

If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free
to call us at (360) 734-1540.
Symptom
Machine does not
start or a circuit
breaker trips.

Possible Cause

Possible Solution

1. (First time operation only) Lathe is
wired out of phase.

1. Correct out-of-phase wiring (refer to Page 17 for
details).

2. Emergency stop push-button is
engaged or at fault.

2. Rotate button clockwise until it pops out to reset it
for operation; replace if not working properly.

3. Spindle ON/OFF switch is at fault.

3. Move the spindle ON/OFF lever to ON; replace bad
switch.

4. Power supply is switched OFF at
main power switch or breaker.

4. Make sure main power switch and circuit breaker
are turned ON.

5. Wall fuse/circuit breaker is blown/
tripped; short in electrical system;
start-up load too high for circuit.

5. Verify circuit is rated for machine amp load;
troubleshoot and repair cause of overload; replace
weak breaker; ﬁnd/repair electrical short.

6. Fuse has blown in machine
electrical box due to thermal
overload.

6. Replace fuse; determine if overload is due to heavy
operation; ensure power source has high enough
voltage and cord is correctly sized.

7. One or more kill switches are
engaged.

7. Verify electrical box door, chuck guard, spindle,
and brake switches are not engaged. Verify that
headstock oil is pumping.

8. Thermal overload relay has tripped.

8. Turn the thermal relay cut-out dial to increase
working amps and push the reset pin. Replace if
tripped multiple times (weak relay).

9. Motor connection wired incorrectly.

9. Correct motor wiring connections.

10. Oil pump motor operating, but no
oil is seen pumping in sight glass.

10. Clean clogged tank suction screen, ﬁll headstock oil
tank to full, or replace oil pump.

11. Limit/kill switch at fault.

11. Test all limit/kill switches and replace as necessary.

12. Contactor not getting energized/has
burnt contacts.

12. Test for power on all legs and contactor operation.
Replace unit if faulty.

13. Wiring is open/has high resistance.

13. Check for broken wires or disconnected/corroded
connections, and repair/replace as necessary.

14. Motor is at fault.

14. Test/repair/replace.

15. Frequency drive unit is at fault.

15. Contact frequency drive manufacturer for list of
authorized service providers in your area.

Loud, repetitious
noise coming from
lathe at or near the
motor.

1. Pulley set screws or keys are
missing or loose.

1. Inspect keys and set screws. Replace or tighten if
necessary.

2. Motor fan is hitting the cover.

2. Tighten fan, shim cover, or replace items.

Motor overheats.

1. Motor overloaded.

1. Reduce load on motor.

2. Frequency drive unit is at fault.

2. Contact frequency drive manufacturer for list of
authorized service providers in your area.

1. Excessive depth of cut or feed rate.

1. Decrease depth of cut or feed rate.

2. Spindle speed or feed rate wrong for
cutting operation.

2. Refer to the feeds and speeds charts in
Machinery's Handbook or a speeds and feeds
calculator on the internet.

3. Cutting tool is dull.

3. Sharpen or replace the cutting tool.

Motor is loud when
cutting, or bogs
down under load.

-74-

For Machines Mfg. Since 7/09
Symptom

TROU B LESHOOTI NG

Possible Cause

EVS Toolroom Lathes
Possible Solution

1. Workpiece is unbalanced.

1. Re-install workpiece as centered with the spindle
bore as possible.

2. Loose or damaged belt(s).

2. Tighten/replace the belt as necessary (Page 69).

3. V-belt pulleys are not properly
aligned.

3. Align the V-belt pulleys.

4. Worn or broken gear present.

4. Inspect gears and replace if necessary.

5. Chuck or faceplate has become
unbalanced.

5. Rebalance chuck or faceplate; contact a local
machine shop for help.

6. Gears not aligned in headstock or
no backlash.

6. Adjust gears and establish backlash.

7. Broken gear or bad bearing.

7. Replace broken gear or bearing.

8. Workpiece is hitting stationary
object.

8. Stop lathe immediately and correct interference
problem.

9. Spindle bearings at fault.

9. Rest spindle bearing preload or replace worn
spindle bearings.

1. Wrong spindle speed or feed rate.

1. Adjust for appropriate spindle speed and feed rate.

2. Dull tooling or poor tool selection.

2. Sharpen tooling or select a better tool for the
intended operation.

3. Tool height not at center line.

3. Adjust tool height to center line (Page 41).

4. Too much play in gibs.

4. Tighten gibs (Page 66).

Tapered tool
difﬁcult to remove
from tailstock quill.

1. Quill is not retracted all the way
back into the tailstock.

1. Turn the quill handwheel until it forces taper out of
quill.

2. Contaminants not removed from
taper before inserting into quill.

2. Clean the taper and bore and re-install tapered tool.

Cross slide,
compound, or
carriage feed has
sloppy operation.

1. Gibs are out of adjustment.

1. Tighten gib screw(s). See (Page 66).

2. Handwheel is loose or backlash is
high.

2. Tighten handwheel fasteners, adjust handwheel
backlash to a minimum.

3. Lead screw mechanism worn or out
of adjustment.

3. Adjust leadscrew to remove endplay (Page 66).

Cross slide,
compound, or
carriage feed
handwheel is hard
to move.

1. Dovetail slides loaded up with
shavings, dust, or grime.

1. Remove gibs, clean ways/dovetails, lubricate, and
readjust gibs.

2. Gib screws are too tight.

2. Loosen gib screw(s) slightly, and lubricate bedways.

3. Backlash setting too tight (cross
slide only).

3. Slightly loosen backlash setting (Page 66).

4. Bedways are dry.

4. Lubricate bedways and handles.

1. Tool holder not tight enough.

1. Check for debris, clean, and retighten.

2. Cutting tool sticks too far out of tool
holder; lack of support.

2. Re-install cutting tool so no more than 1⁄3 of the total
length is sticking out of tool holder.

3. Gibs are out of adjustment.

3. Tighten gib screws at affected component.

4. Dull cutting tool.

4. Replace or resharpen cutting tool.

5. Incorrect spindle speed or feed rate.

5. Use the recommended spindle speed.

Entire machine
vibrates upon
startup and while
running.

Bad surface ﬁnish.

Cutting tool
or machine
components vibrate
excessively during
cutting.

-75-

EVS Toolroom Lathes
Symptom

TROU B LESHOOTI NG
Possible Cause

For Machines Mfg. Since 7/09
Possible Solution

Workpiece is
tapered.

1. Headstock and tailstock are not
properly aligned with each other.

1. Realign the tailstock to the headstock spindle bore
centerline (Page 34).

Chuck jaws will
not move or do not
move easily.

1. Chips lodged in the jaws or scroll
plate.

1. Remove jaws, clean and lubricate scroll plate, then
replace jaws.

Carriage will not
feed, or is hard to
move.

1. Gears are not all engaged.

1. Adjust gear levers.

2. Loose screw on the feed handle.

2. Tighten.

3. Carriage lock is tightened down.

3. Check to make sure the carriage lock bolt is fully
released.

4. Chips have loaded up on bedways.

4. Frequently clean away chips that load up during
turning operations.

5. Bedways are dry and in need of
lubrication.

5. Lubricate bedways and handles.

6. Carriage stop is interfering.

6. Check carriage stop position, and adjust it as
necessary (Page 42).

7. Gibs are too tight.

7. Loosen gib screw(s) slightly (Page 66).

8. Gears or shear pin broken.

8. Replace gears or shear pin (Page 71).

Gear change levers
will not shift into
position.

1. Gears not aligned inside headstock.

1. Rotate spindle by hand with light pressure on the
lever until gear falls into place.

Headstock oil
does not ﬂow or
circulate properly.

1. (For ﬁrst time operation only) the
lathe is wired out-of-phase.

1. Correct out-of-phase wiring (refer to Page 17 for
details).

2. Emergency stop push-button is
engaged or at fault.

2. Rotate button clockwise until it pops out to reset it
for operation; replace if not working properly.

3. Power supply is switched OFF at
main power switch or breaker.

3. Make sure main power switch and circuit breaker
are turned ON.

4. Insufﬁcient oil level in headstock
oil tank or incorrect oil used in
headstock oil tank.

4. Add oil to the headstock oil tank (refer to
Headstock "Checking & Adding Oil" on Page 56
for details). Make sure to use the correct type of oil.

5. Suction screen clogged.

5. Clean suction screen (see Figure 111 on Page 57).

6. Pinched/damaged oil line.

6. Trace oil lines to inspect and replace pinched/
damaged line.

7. Suction side of pump drawing air.

7. Locate leak and reseal/replace affected components.

8. Leak in distribution manifold
located inside headstock.

8. Locate leak and reseal/replace affected components.

9. Pump motor at fault.

9. Replace/repair pump motor.

-76-

WAR R ANT Y
WARRANTY & RETURNS

Warranty

This quality product is warranted by South Bend Lathe Company to the original buyer for one year
from the date of purchase. This warranty does not apply to consumable parts, or defects due to any
kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not
reimburse for third party repairs. In no event shall we be liable for death, injuries to persons or
property, or for incidental, contingent, special or consequential damages arising from the use of our
products.
We do not warrant or represent that this machine complies with the provisions of any law, act, code,
regulation, or standard of any domestic or foreign government, industry, or authority. In no event
shall South Bend’s liability under this warranty exceed the original purchase price paid for this
machine. Any legal actions brought against South Bend Lathe Company shall be tried in the State of
Washington, County of Whatcom.
This is the sole written warranty for this machine. Any and all warranties that may be implied by
law, including any merchantability or fitness, for any purpose, are hereby limited to the duration of
this warranty. To take advantage of this warranty, contact us by mail or phone to give us the details
of the problem you are having.
Thank you for your business and continued support.

South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
PHONE: (360) 734-1540 (Administrative Ofﬁces)
FAX: (360) 676-1075 (International)
FAX: (360) 734-1639 (USA only)

southbendlathe.com

Printed In Taiwan

#BLTRCR12117

16" X 60" EVS TOOLROOM LATHES
MODEL SB1014 - 220V
MODEL SB1015 - 440V

SPECIFICATIONS

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906!

For Machines Mfg. Since 7/09

Machine Specifications
P.O. Box 2027, Bellingham, WA 98227 U.S.A.
PHONE: (360) 734-1540 • © South Bend Lathe Co.

www.southbendlathe.com

Model SB1014
16" x 60" EVS Toolroom Lathe
Product Dimensions:
Weight ........................................................................................................................................................................3300 lbs.
Length/Width/Height .................................................................................................................................... 106" x 33" x 61"
Foot Print (Length/Width) ................................................................................................................................. 1017⁄8" x 191⁄2"
Shipping Dimensions:
Type ................................................................................................................................................................ Wood Slat Crate
Weight .........................................................................................................................................................................3652 lbs.
Length/Width/Height ..................................................................................................................................... 109" x 45" x 69"
Electrical:
Required Power Source .........................................................................................................................220V, 3-Phase, 60 Hz
Inverter Type .............................................................................................................................................Yaskawa G7A25P5
Switch ............................................................................................................................... Magnetic with Thermal Protection
Switch Voltage .................................................................................................................................................................. 220V
Recommended Cord .......................................................................................................................8 Gauge, 4 Wire, 300 VAC
Recommended Circuit Size ..........................................................................................................................................30 Amp
Plug Included ........................................................................................................................................................................ No
Recommended Plug Type .............................................................................................................................................. L15-30
Motors:
Main
Type .......................................................................................................................................................TEFC Induction
Horsepower........................................................................................................................................................... 71⁄2 HP
Voltage ..................................................................................................................................................................... 220V
Phase .................................................................................................................................................................. 3-Phase
Amps .......................................................................................................................................................................... 20A
Speed............................................................................................................................................................... 4500 RPM
Cycle ....................................................................................................................................................................... 60 Hz
Number Of Speeds ............................................................................................................................................ Variable
Power Transfer.........................................................................................................................................V-Belt & Gear
Bearings................................................................................................................... Shielded and Permanently Sealed
Lubrication
Type .......................................................................................................................................................TEFC Induction
Horsepower............................................................................................................................................................. 1⁄4 HP
Voltage ..................................................................................................................................................................... 220V
Phase .................................................................................................................................................................. 3-Phase
Amps ......................................................................................................................................................................... 1.4A
Speed............................................................................................................................................................... 1725 RPM
Cycle ....................................................................................................................................................................... 60 Hz
Number of Speeds ..........................................................................................................................................................1
Power Transfer............................................................................................................................................ Direct Drive
Bearings................................................................................................................... Shielded and Permanently Sealed
Model SB1014

Page 1 of 3

Coolant
Type .......................................................................................................................................................TEFC Induction
Horsepower............................................................................................................................................................. 1⁄8 HP
Voltage ..................................................................................................................................................................... 220V
Phase .................................................................................................................................................................. 3-Phase
Amps ......................................................................................................................................................................... 0.3A
Speed............................................................................................................................................................... 3450 RPM
Cycle ....................................................................................................................................................................... 60 Hz
Number of Speeds ..........................................................................................................................................................1
Power Transfer............................................................................................................................................ Direct Drive
Bearings................................................................................................................... Shielded and Permanently Sealed
Main Specifications:
Operation Information
Swing Over Bed .................................................................................................................................................... 16.14"
Distance Between Centers ........................................................................................................................................ 60"
Swing Over Cross Slide ...................................................................................................................................... 10.375"
Swing Over Saddle................................................................................................................................................ 13.54"
Swing Over Gap .................................................................................................................................................... 22.95"
Max Tool Bit Size .................................................................................................................................................... 0.75"
Spindle Nose to Gap ............................................................................................................................................... 10.2"
Compound Slide Travel ............................................................................................................................................ 5.1"
Carriage Travel .......................................................................................................................................................... 54"
Cross Slide Travel ................................................................................................................................................... 9.25"
Headstock Information
Spindle Bore ........................................................................................................................................................ 2.0625"
Spindle Taper ......................................................................................................................................................... MT#6
Number of Spindle Speeds ............................................................................................................................... Variable
Range of Spindle Speeds ......................................................................................................................... 20–2500 RPM
Spindle Type............................................................................................................................................. D1-6 Camlock
Spindle Bearings ..............................................................................................................NSK or NTN Tapered Roller
Spindle Length ...................................................................................................................................................... 24.24"
Spindle Length with 3-Jaw Chuck ...................................................................................................................... 30.31"
Spindle Length with 4-Jaw Chuck ...................................................................................................................... 34.08"
Tailstock Info
Tailstock Travel ........................................................................................................................................................... 6"
Tailstock Taper ...................................................................................................................................................... MT#4
Tailstock Barrel Diameter .................................................................................................................................... 2.047"
Threading Info
No of Inch Threads ......................................................................................................................................................45
Range of Inch Threads..................................................................................................................................... 2–72 TPI
No of Longitudinal Feeds ............................................................................................................................................17
Range of Longitudinal Feeds ................................................................................................................... 0.002"–0.067"
No of Cross Feeds ........................................................................................................................................................17
Range of Cross Feeds ................................................................................................................................ 0.001"–0.034"
No of Metric Threads ...................................................................................................................................................39
Range of Metric Threads ............................................................................................................................... 0.2–14mm
No of Diametral Pitches ..............................................................................................................................................21
Range of Diametral Pitches ............................................................................................................................. 8–44 DP
No of Modular Pitches .................................................................................................................................................18
Range of Modular Pitches ............................................................................................................................0.3–3.5 MP

Model SB1014

Page 2 of 3

Dimensions
Bed Width ................................................................................................................................................................ 101⁄4"
Leadscrew TPI ...............................................................................................................................................................4
Leadscrew Length ................................................................................................................................................. 83.58"
Steady Rest Capacity ........................................................................................................................................ 5⁄16"–45⁄16"
Follow Rest Capacity .......................................................................................................................................... 5⁄8"–31⁄8"
Faceplate Size ............................................................................................................................................................ 12"
Leadscrew Diameter ................................................................................................................................................. 11⁄8"
Feed Rod Diameter ..................................................................................................................................................... 3⁄4"
Floor To Center Height .......................................................................................................................................... 431⁄2"
Height With Leveling Jacks ................................................................................................................................... 441⁄2"
Construction
Base Construction ............................................................................................................................................ Cast Iron
Headstock Construction .................................................................................................................................. Cast Iron
Headstock Gears Construction ................................................................................................. Flame Hardened Steel
Bed Construction ..................................................................................... Induction Hardened and Ground Cast Iron
Stand Construction .......................................................................................................................................... Cast Iron
Other Specifications:
Country Of Origin ........................................................................... Taiwan (Some Components Made in USA and Japan)
Warranty .........................................................................................................................................................................1 Year
Serial Number Location ............................................................................................... ID Label on Rear Side of Left Stand
Customer Setup and Cleaning Time .................................................................................................Approximately 2 Hours
Features:
Allen Bradley Electrical Components
Meehanite Casting, Signature South Bend 3 V-Way Bed
Safety Chuck Guard with Micro-Switch Shut-Off
Halogen Work Light
4-Way Tool Post
Complete Coolant System
Micrometer Carriage Stop
Threading Dial Indicator
NSK or NTN Japanese Spindle Bearings
Full Length Splash Guard
Front Removable Sliding Chip Tray
Yaskawa G7A25P5 Inverter
Completely Enclosed Universal Gearbox for Cutting Inch, Metric, Modular and Diametral Pitches
Pressurized Lubrication System for Headstock Gears and Bearings
Dial Controlled, Variable Spindle Speeds with Digital Read Out
Jog Button and Emergency Stop
Accessories Included:
9" 3-Jaw Scroll Chuck Mounted to 9" D1-6 Back Plate
10" 4-Jaw Independent Chuck D1-6
12" Faceplate D1-6
Follow Rest
Steady Rest with Roller Bearing Tips
#6 to #4 Morse Taper Spindle Sleeve
Two Morse Taper #4 Dead Centers (1 Carbon Steel and 1 Carbide-Tipped)
Eight Leveling Pads, Service Tools, Tool Box, and USA Written Manual
Optional Accessories:
SB1269
SB1268
SB1267
SB1239
SB1279
SB1280

Taper Attachment (Unmounted)
Collet Attachment 5-C, Quick Change (Unmounted)
10" Backplate D1-6
Hi-Performance Morse Taper #4 Live Center
Precision 5-C Collets, Set of Eight (1⁄8"-1", in 1⁄8" Increments)
Precision 5-C Collets, Set of 15 (1⁄8"-1", in 1⁄16" Increments)

Model SB1014

Page 3 of 3

Machine Specifications
P.O. Box 2027, Bellingham, WA 98227 U.S.A.
PHONE: (360) 734-1540 • © South Bend Lathe Co.

www.southbendlathe.com

Model SB1015
16" x 60" EVS Toolroom Lathe
Product Dimensions:
Weight ........................................................................................................................................................................3300 lbs.
Length/Width/Height .................................................................................................................................... 106" x 33" x 61"
Foot Print (Length/Width) ................................................................................................................................. 1017⁄8" x 191⁄2"
Shipping Dimensions:
Type ................................................................................................................................................................ Wood Slat Crate
Weight .........................................................................................................................................................................3652 lbs.
Length/Width/Height ..................................................................................................................................... 109" x 45" x 69"
Electrical:
Required Power Source .........................................................................................................................440V, 3-Phase, 60 Hz
Inverter Type .............................................................................................................................................Yaskawa G7A25P5
Switch ............................................................................................................................... Magnetic with Thermal Protection
Switch Voltage .................................................................................................................................................................. 440V
Recommended Circuit Size ..........................................................................................................................................15 Amp
Plug Included ........................................................................................................................................................................ No
Recommended Plug Type ....................................................................................... Hardwire to Locking Disconnect Switch
Motors:
Main
Type .......................................................................................................................................................TEFC Induction
Horsepower........................................................................................................................................................... 71⁄2 HP
Voltage ..................................................................................................................................................................... 440V
Phase .................................................................................................................................................................. 3-Phase
Amps .......................................................................................................................................................................... 10A
Speed........................................................................................................................................................... 0–4500 RPM
Cycle ....................................................................................................................................................................... 60 Hz
Number Of Speeds ............................................................................................................................................ Variable
Power Transfer.........................................................................................................................................V-Belt & Gear
Bearings................................................................................................................... Shielded and Permanently Sealed
Lubrication
Type .......................................................................................................................................................TEFC Induction
Horsepower............................................................................................................................................................. 1⁄4 HP
Voltage ..................................................................................................................................................................... 440V
Phase .................................................................................................................................................................. 3-Phase
Amps ......................................................................................................................................................................... 0.6A
Speed............................................................................................................................................................... 1725 RPM
Cycle ....................................................................................................................................................................... 60 Hz
Number of Speeds ..........................................................................................................................................................1
Power Transfer............................................................................................................................................ Direct Drive
Bearings................................................................................................................... Shielded and Permanently Sealed
Model SB1015

Page 1 of 3

Coolant
Type .......................................................................................................................................................TEFC Induction
Horsepower............................................................................................................................................................. 1⁄8 HP
Voltage ..................................................................................................................................................................... 440V
Phase .................................................................................................................................................................. 3-Phase
Amps ....................................................................................................................................................................... 0.15A
Speed............................................................................................................................................................... 3450 RPM
Cycle ....................................................................................................................................................................... 60 Hz
Number of Speeds ..........................................................................................................................................................1
Power Transfer............................................................................................................................................ Direct Drive
Bearings................................................................................................................... Shielded and Permanently Sealed
Main Specifications:
Operation Information
Swing Over Bed .................................................................................................................................................... 16.14"
Distance Between Centers ........................................................................................................................................ 60"
Swing Over Cross Slide ...................................................................................................................................... 10.375"
Swing Over Saddle................................................................................................................................................ 13.54"
Swing Over Gap .................................................................................................................................................... 22.95"
Max Tool Bit Size .................................................................................................................................................... 0.75"
Spindle Nose to Gap ............................................................................................................................................... 10.2"
Compound Slide Travel ............................................................................................................................................ 5.1"
Carriage Travel .......................................................................................................................................................... 54"
Cross Slide Travel ................................................................................................................................................... 9.25"
Headstock Information
Spindle Bore ........................................................................................................................................................ 2.0625"
Spindle Taper ......................................................................................................................................................... MT#6
Number of Spindle Speeds ............................................................................................................................... Variable
Range of Spindle Speeds ......................................................................................................................... 20–2500 RPM
Spindle Type............................................................................................................................................. D1-6 Camlock
Spindle Bearings ..............................................................................................................NSK or NTN Tapered Roller
Spindle Length ...................................................................................................................................................... 24.24"
Spindle Length with 3-Jaw Chuck ...................................................................................................................... 30.31"
Spindle Length with 4-Jaw Chuck ...................................................................................................................... 34.08"
Tailstock Info
Tailstock Travel ........................................................................................................................................................... 6"
Tailstock Taper ...................................................................................................................................................... MT#4
Tailstock Barrel Diameter .................................................................................................................................... 2.047"
Threading Info
No of Inch Threads ......................................................................................................................................................45
Range of Inch Threads..................................................................................................................................... 2–72 TPI
No of Longitudinal Feeds ............................................................................................................................................17
Range of Longitudinal Feeds ................................................................................................................... 0.002"–0.067"
No of Cross Feeds ........................................................................................................................................................17
Range of Cross Feeds ................................................................................................................................ 0.001"–0.034"
No of Metric Threads ...................................................................................................................................................39
Range of Metric Threads ............................................................................................................................... 0.2–14mm
No of Diametral Pitches ..............................................................................................................................................21
Range of Diametral Pitches ............................................................................................................................. 8–44 DP
No of Modular Pitches .................................................................................................................................................18
Range of Modular Pitches ............................................................................................................................0.3–3.5 MP

Model SB1015

Page 2 of 3

Model SB1015

Page 3 of 3

South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
PHONE: (360) 734-1540 (Administrative Offices)
FAX: (360) 676-1075 (International)
FAX: (360) 734-1639 (USA only)

southbendlathe.com

Printed In Taiwan

#BL12162-12163

14" & 16" EVS TOOLROOM LATHES
MODELS SB1012/SB1014/SB1037 - 220V
MODELS SB1013/SB1015/SB1038 - 440V

WIRING MANUAL

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906!

For Machines Mfg. Since 7/09

Scope of Manual
This manual assumes that the reader has a basic understanding of safe electrical practices and
general wiring concepts, including how to safely make wire connections and avoid shorts. This
manual is intended to be a reference source in the event that a repair or component replacement
becomes necessary during the life of the machine. If an electrical repair becomes necessary, and you
do not have experience working with electricity or performing wiring tasks, we strongly encourage
you to get help from an experienced individual, such as an electrician, or from our technical support.
Following this advice will help you avoid serious personal injury, maintain your warranty, and keep
your machine operating correctly.

Manual Feedback
We've made every effort to be accurate when documenting this machine. However, errors sometimes
happen or the machine design changes after the documentation process—so the manual may not
exactly match your machine. If a difference between the manual and machine leaves you in doubt,
contact our customer service (see bottom of page) for clarification.
We highly value customer feedback on our manuals. If you have a moment, please share your
experience using this manual. What did you like about it? Is there anything you would change to
make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use?
South Bend Lathe, Inc.
C
/O Technical Documentation Manager
P.O. Box 2027
Bellingham, WA 98227
Email: manuals@southbendlathe.com

Updates
For your convenience, any updates to this manual will be available to download free of charge
through our website at:
www.southbendlathe.com

Customer Service
We stand behind our machines. If you have any service questions, parts requests or general questions
about the machine, feel free to contact us.
South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
Phone: (360) 734-1540
Parts Department: (417) 886-2954
Fax: (360) 676-1075 (International)
Fax: (360) 734-1639 (USA Only)
Email: cs@southbendlathe.com

For Machines Mfg. Since 8/09

ELECTRICAL

EVS Toolroom Lathes

ELECTRICAL

Electrical Safety Instructions
These pages are accurate at the time of printing. In the constant effort to improve, however, we may
make changes to the electrical systems of future machines. Study this section carefully. If you see
differences between your machine and what is shown in this section, call Technical Support at (360)
734-1540 for assistance BEFORE making any changes to the wiring on your machine.
1.

Shock Hazard: Working on wiring that is
connected to a power source is extremely
dangerous. Touching electriﬁed parts will
result in personal injury including but
not limited to severe burns, electrocution,
or death. Disconnect the power from
the machine before servicing electrical
components!

Capacitors/Inverters: Some capacitors and
power inverters store an electrical charge for
up to 10 minutes after being disconnected
from the power source. To reduce the risk of
being shocked, wait at least this long before
working on capacitors.

Wire/Component Damage: Damaged wires
or components increase the risk of serious
personal injury, ﬁre, or machine damage. If
you notice that any wires or components are
damaged while performing a wiring task,
replace those wires or components before
completing the task.

Modiﬁcations: Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or ﬁre.

Motor Wiring: The motor wiring shown
in these diagrams is current at the time of
printing, but it may not match your machine.
Always use the wiring diagram inside the
motor junction box.

Circuit Requirements: You MUST follow
the requirements at the beginning of this
manual when connecting your machine to a
power source.

Wire Connections: All connections must be
tight to prevent wires from loosening during
machine operation. Double-check all wires
disconnected or connected during any wiring
task to ensure tight connections.

Experiencing Difﬁculties: If you are
experiencing difﬁculties understanding the
information included in this section, contact
our Technical Support at (360) 734-1540.

WIRING DIAGRAM COLOR KEY
BLACK

BLUE
WHITE

RED

PINK

WHITE

BLUE

GREEN

LIGHT
BLUE

PURPLE

YELLOW
GREEN

BROWN

GRAY

ORANGE

TURQUIOSE

YELLOW

NOTICE:

The photos and diagrams included in this section are best viewed in color. You can
see them in color at www.southbendlathe.com.

-1-

EVS Toolroom Lathes

ELECTRICAL

For Machines Mfg. Since 8/09
wiring overview

Wiring Overview

7 Power Supply

6 Electrical

Connection
Page 13.

Box, Pages 6
& 7.

220 VAC
3-PH

8
Spindle RPM
Sensor, Page 14.

Work Lamp,
Page 14.

Chuck Guard Limit
Switch, Page 14.

Brake Limit
Switch, Page 14.

@
9

Door Limit
Switch, Page 14.

?
Oil Pressure
Switch,
>
Page 10.

Oil Pump
Motor,
Page 10.

Coolant
Pump Motor,
Page 11.

; Control Panel,
Page 12.

Spindle Motor,
Page 9.

-2-

Spindle
Switch,
Page 13.

For Machines Mfg. Since 8/09

EVS Toolroom Lathes

ELECTRICAL

visual index

Component Location Index

6 Cooling Fan,

8 Work Lamp,

Page 6.

Page 14.

6 Electrical

Box, Pages 6
& 7.

6 Main Power

: Coolant

Switch, Page 6.

Pump Motor,
Page 11.

Oil Pressure
Sensor,
Page 10.

@ Brake Limit

Switch, Page 14.

;

Control Panel,
Page 12.

Oil Pump
Motor,
Page 10.

A Chuck Guard Limit
Switch, Page 14.

Door Limit
Switch, Page 14.

Spindle RPM
Sensor, Page 14.

8 Work Lamp,
Page 14.

9 Spindle

Switch,
Page 13.

< Spindle Motor,
Page 9.

Figure 1. Component location index.

-3-

0 L13

L11

220

TRANSFORMER

6 7

19 20 12 13 14 63 64

FOR 440V ONLY:
SB1013
SB1015
SB1038
1

L2
5

AMP

2 T1

L2 5

6 T3

8 T4

THERMAL
RELAY

6 T3

CONTACTOR
Allen Bradley
C09 400

L1 L2

2 T1

MASTER
POWER SWITCH

V1 U2
4
W2
W1
V2
L11
2

FOR 220V: RANGE 0.24A–0.4A, SET AT 0.35A
FOR 440V: RANGE 0.24A–0.4A, SET AT 0.24A

5 A1

CIRCUIT BOARD

KR4

2 T1

L2 5

6 T3

L11

8 T4

L11

THERMAL
RELAY

2 V2

CONTACTOR
Allen Bradley
C09 400

AMP

2 T1

COOLING
FAN

To Control Panel, Page 12.

Electrical Box Wiring

L2
3 L13 2
L1 L3
11 0

KR4 NC

3 11

To Varispeed Unit, Page 7.

KR4 NO

THERMAL RESISTOR

0 220 380 400 415 440

L3 L1

KR4 COM

KR3

COM

X
COM

24V

KR1

KR2

NC X

X
CHUCK
X

150
100
100

SB1013: 600W
SB1015: 800W
SB1038: 800W

X
X
COM

X
X
SROTATION

24VXCOM

BRAKE
X

NO X

X
X

X
NO X

NO X

NC X

X
X

ELECTRICAL

JOG

X
1 X

X
2 X

X
X

40
20
20

SB1012: 600W
SB1014: 800W
SB1037: 800W

CSS

-4X

X
3 X

EVS Toolroom Lathes
For Machines Mfg. Since 8/09
box1

FOR SB1012/SB1014/SB1037 220V: RANGE 1.6A–2.4A, SET AT 1.8A
FOR SB1013/SB1015/SB1038 440V: RANGE 0.6A–1.0A, SET AT 0.8A

To Spindle
Motor,
Page 9.

U2
V2

U1
V1

L13

L11

3 4

To Brake
Limit
Switch,
Page 14.

To
Spindle
Switch,
Page 13.

11 COM K

B2
U

N6H@6L6

?3 ?4 ?5
?#
?$ 79

Varispeed

L11 L13

To Spindle
RPM
Sensor,
Page 14.

L11 L13

To Work
Lamp,
Page 14.

Limit Switch,
Page 14.

A To Chuck Guard

Main
Junction
Block

To Circuit Board,
Page 6.

A1 6

12 14 18
23

To Oil
Pressure
Sensor,
Page 10.

?B B% 5% B& 5&
DB D D E E
E+ E#" E## E#$ #9

E5
H
E*

VARIABLE SPEED UNIT
(REFER TO YASKAWA OWNERS MANUAL)

B5
35
E)

11 COM K

B$
H
E(

B#
3%
E'

3?
3$
E&

35
3#
E%

17 13
15
16

To Door
Limit
Switch,
Page 14.

W L11 L13 U1 V1 W1 U2 V2 W2

To Coolant
To Oil
Pump Motor, Pump
Page 11.
Motor,
Page 10.

79 8?
E5
E# E$

V1 U2
W2
4
W1
2
V2
L11

COM

6 7

Electrical Box Wiring

To Power
Connection,
Page 13.

ELECTRICAL

Ground

5 A1

L11

L2
3 L13 2
L1 L3
11 0

L13

For Machines Mfg. Since 8/09
EVS Toolroom Lathes
box2

-5-

EVS Toolroom Lathes

ELECTRICAL

For Machines Mfg. Since 8/09

box photo

Electrical Box

Fig. 2. Electrical box.

-6-

For Machines Mfg. Since 8/09

EVS Toolroom Lathes

ELECTRICAL

he^cYaZVcYejbebdidg

220V Spindle Motor
<

W6
W2

U5
U1

U6
V1

V5
U2
W1
W5

V2
V6
W
V

Junction Box

Ground

SPINDLE
MOTOR (220V)

Figure. 3. Spindle motor location.

To Electrical
Box, Page 7.

440V Spindle Motor
<

W5
W2

W6
U1

U5
V1

U2
W1
V6

V2
V5
W
V

Junction Box
Bk

Ground

SPINDLE
MOTOR (440V)

Figure. 4. Spindle motor location.

To Electrical
Box, Page 7.

-7-

EVS Toolroom Lathes

ELECTRICAL

For Machines Mfg. Since 8/09

220V Oil Pump Motor & Pressure Sensor
To Electrical
Box, Page 7.

>
6

11
X

OIL
PRESSURE
SENSOR

Oil Pressure
Sensor and Pump

U1
V1

V5
W1

Ground

Oil Pump
Motor

U2 V2
W2

OIL PUMP
MOTOR (220V)

Figure. 5. Oil pump motor & pressure sensor location.

To Electrical
Box, Page 7.

440V Oil Pump Motor & Pressure Sensor
To Electrical
Box, Page 7.

>
6

11
X

OIL
PRESSURE
SENSOR

Oil Pressure
Sensor and Pump

U5
U2

U1
V1

V2
V5

W2
W5

Ground

U2 V2
W2

OIL PUMP
MOTOR (440V)
6

-8-

To Electrical
Box, Page 7.

Oil Pump
Motor
Figure. 6. Oil pump motor & pressure sensor location.

For Machines Mfg. Since 8/09

ELECTRICAL

EVS Toolroom Lathes

220V Coolant Pump Wiring
6

To Electrical
Box, Page 7.

:
Coolant Pump
2
3

U1
V1
W1
5 W1

6
4
V1

Figure. 7. Coolant pump location.
Ground
Ground

COOLANT
PUMP MOTOR
(220V)

440V Coolant Pump Wiring
6

To Electrical
Box, Page 7.

Coolant Pump

2
3

U1
V1
W1
5 W1

6
4
V1

Figure. 8. Coolant pump location.
Ground

COOLANT
PUMP MOTOR
(440V)

-9-

EVS Toolroom Lathes

For Machines Mfg. Since 8/09

ELECTRICAL

Control Panel Wiring
control panel
and coolant motor

Control Panel

Fig. 9. Control panel location.

6
To Main Junction
Block, Page 7.

To Main Junction
Block, Page 7.

To Circuit
Board, Page 6.

L11
L13

COM

14
X

To Circuit
Board, Page 6.

2
12
X

To Electrical
Box, Page 7.

13
X

;

GND

220V

+12V

110V

TACHOMETER DISPLAY

X1
3
SPINDLE
2
SPEED
1
DIAL

COOLANT
PUMP
SWITCH

X2
POWER
LAMP

JOG 4
BUTTON

Control Panel Switches,
Figure 9.

-10-

EMERGENCY
STOP
BUTTON

For Machines Mfg. Since 8/09

EVS Toolroom Lathes

ELECTRICAL

spindle rotation
and power conntection

Spindle Rotation Switch

6
8

Spindle Rotation
Switch

To Main Junction
Block, Page 7.

COM

6
NC

COM

9
Spindle Rotation Switch,
Figure 10.
Fig. 10. Spindle rotation switch location.

220V Power Connection
7
Ground
L1

Hot
L3

Hot
Hot

Inside Electrical
Box, Page 7.
L1

15-20 PLUG
(as recommended)

MASTER
POWER SWITCH
2

440V Power Connection
7
L1

Hot
L1
L2

Hot

Inside Electrical
Box, Page 7.

Hot
Ground

DISCONNECT
SWITCH
(as recommended)

MASTER
POWER SWITCH
2

-11-

EVS Toolroom Lathes

For Machines Mfg. Since 8/09

ELECTRICAL

Additional Component Wiring
Spindle
RPM Sensor

8
Door Limit
Switch

Work Light

additional compontnet
Wt

Fig. 11. RPM sensor and door limit switch location.

Bk 2

Door Limit
Switch, Figure 11.
COMMON

Brake Limit
Switch

1
X

Spindle RPM Sensor, Figure 11.
COM

K
X
L

Fig. 12. Brake limit switch location.

Chuck Guard Limit Switch, Figure 13.
3
NC

9
X
A1

4
NC

Brake Limit Switch, Figure 12.

Chuck
Guard Limit
Switch
Fig. 13. Chuck guard limit switch.

-12-

6
To Electrical
Box, Page 7.

5
X
A1

WARRANTY & RETURNS

Warranty

South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
PHONE: (360) 734-1540 (Administrative Ofﬁces)
FAX: (360) 676-1075 (International)
FAX: (360) 734-1639 (USA only)

southbendlathe.com

Printed In Taiwan

#JB12236

16" X 60" EVS TOOLROOM LATHES
MODEL SB1014 - 220V
MODEL SB1015 - 440V

PARTS MANUAL

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906!

For Machines Mfg. Since 7/09

Scope of Manual
The parts breakdowns in this manual are provided to facilitate the service and repair of this machine
as follows: (1) By helping the mechanic understand how and where individual parts fit together;
and (2) by establishing a numbering system from which available replacement parts can be ordered.
Please note that not all parts shown are available for purchase and some individual parts may only
be available in assemblies with other parts. In the case of fasteners or other off-the-shelf hardware,
we will happily provide customers with replacements, but for the sake of expediency, these can also
be found at your local hardware or industrial supply store.

Updates
For your convenience, any updates to this manual will be available to download free of charge
through our website at:
www.southbendlathe.com

Table of Contents
Headstock Casing....................................................................................................................................... 2
Headstock Controls..................................................................................................................................... 3
Headstock Upper Gearing.......................................................................................................................... 5
Headstock Transfer Gearing...................................................................................................................... 7
Gearbox Gearing......................................................................................................................................... 8
Gearbox Controls...................................................................................................................................... 10
Apron - Front View................................................................................................................................... 12
Apron - Rear View..................................................................................................................................... 14
Dial Indicator............................................................................................................................................ 16
Carriage Stop............................................................................................................................................ 16
Compound Slide & Tool Post.................................................................................................................... 17
Saddle Body & Controls........................................................................................................................... 18
Saddle Base............................................................................................................................................... 20
Bed & Shafts............................................................................................................................................. 21
End Gears.................................................................................................................................................. 23
Motor Assembly........................................................................................................................................ 24
Cabinets & Panels.................................................................................................................................... 26
Headstock Oiling System......................................................................................................................... 28
Tailstock.................................................................................................................................................... 30
Steady Rest............................................................................................................................................... 32
Follow Rest................................................................................................................................................ 32
Electrical Cabinet & Control Panel......................................................................................................... 33
Accessories................................................................................................................................................ 35
Machine Labels (Front View)................................................................................................................... 36
Machine Labels (Rear View).................................................................................................................... 37

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Headstock Casing
1
2

4
10

6
11

9-1

12
13
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1
2
3
4
5
6
7

PSB10120001
PCAP29M
PSB10120003
PSB10120004
PCAP50M
PSB10120006
PCAP15M

OIL FILL PLUG
CAP SCREW M6-1 X 40
HEADSTOCK COVER
COVER OIL SEAL M4 X 1700
CAP SCREW M5-.8 X 10
PIPE CLIP 5MM
CAP SCREW M5-.8 X 20

8
9
9-1
10
11
12
13

PFH30M
PSB10120009
PSB10120009-1
PSB10120010
PSB10120011
PSB10120012
PRIV001M

FLAT HD SCR M5-.8 X 8
OIL DISTRIBUTOR A-5S
OIL DISTRIBUTOR BRACKET
PIPE JOINT
NYLON TUBE
HEADSTOCK CONTROL PLATE
STEEL FLUTED RIVET 2 X 5MM

-2-

PARTS

For Machines Mfg. Since 8/09

Model SB1014/SB1015 Parts

Headstock Controls
21

25
27 26
31
35

42
45

47
42
44
30
45

46
40

44
39

29
18

15
17

20
19 18

49
48

43
46

37
41

24
28

37
21

33
34

16
49
50

-3-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Headstock Controls Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

PSS30M
PSB10120015
PSB10120016
PSTB001M
PSB10120018
PORP014
PSB10120020
PORP021
PSB10120022
PR03M
PSB10120024
PRP31M
PSB10120026
PRP32M
PSB10120028
PK01M
PRP16M
PSB10120031
PSB10120032

SET SCREW M10-1.5 X 10
THREADED PLUG M10-1.5
COMPRESSION SPRING M8 X 37
STEEL BALL 8.5MM
HEADSTOCK CASTING PLUG 20MM
O-RING 13.8 X 2.4 P14
HEADSTOCK CASTING PLUG 18MM
O-RING 20.8 X 2.4 P21
SHIFT CAM
EXT RETAINING RING 12MM
SHIFT FORK
ROLL PIN 6 X 36
SHIFT ROD
ROLL PIN 6 X 40
SHIFT CAM
KEY 5 X 5 X 22
ROLL PIN 3 X 25
LONG SHIFT HANDLE
SHIFT HANDLE HUB

33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

PSB10120033
PCAP01M
PSB10120035
PSB10120036
PR05M
PSB10120038
PEC015M
PK12M
PSB10120041
PK164M
PSTB001
PSB10120044
PSB10120045
PSB10120046
PSS20M
PSB10120048
PLW05M
PCAP92M

HANDLE WASHER 6MM
CAP SCREW M6-1 X 16
SHIFT FORK
SHIFT FORK
EXT RETAINING RING 15MM
SHIFT CAM
E-CLIP 8MM
KEY 5 X 5 X 30
SHIFT ROD
KEY 5 X 5 X 17
STEEL BALL 1/4
SHIFT HANDLE HUB
SHORT SHIFT HANDLE
COMPRESSION SPRING 6 X 27
SET SCREW M8-1.25 X 8
OIL SIGHT GLASS
LOCK WASHER 12MM
CAP SCREW M12-1.75 X 40

-4-

80
79

100

96
95

94
93

89
88

71
70

67
66

65
64
63

62
61

57
56

PARTS

For Machines Mfg. Since 8/09
Model SB1014/SB1015 Parts

Headstock Upper Gearing

-5-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Headstock Upper Gearing Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

34
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77

PCAP01M
PSB10120055
PORG050
PR38M
P6206-OPEN
PSB10120059
PK161M
PSB10120061
PR76M
PSB10120063
PSB10120064
PK27M
PR15M
PSB10120067
PSB10140068
PR11M
P6205-OPEN
PSB10120071
PSB10120072
PK62M
P6206RS
PORG085
PSB10120076
PSB10120077

CAP SCREW M6-1 X 16
INBOARD DRIVE SHAFT END CAP
O-RING 54.4 X 3.1 G50
INT RETAINING RING 62MM
BALL BEARING 6206-OPEN
GEAR 24T
KEY 10 X 8 X 25
GEAR 67T
EXT RETAINING RING 52MM
GEAR 38T
DRIVE SHAFT
KEY 7 X 7 X 25
EXT RETAINING RING 30MM
OUTBOARD DRIVE SHAFT END CAP
HEADSTOCK CASTING
EXT RETAINING RING 25MM
BALL BEARING 6205-OPEN
GEAR 30T
INPUT SHAFT
KEY 7 X 7 X 45
BALL BEARING 6206RS
O-RING 84.4 X 3.1 G85
FLANGED BEARING END CAP
OIL SEAL

78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

PSB10120078
PSB10120079
PLW04M
PCAP31M
PSB10120082
PSB10120083
PSB10120084
PSB10120085
PK162M
PK28M
PCAP48M
PSB10120089
PSB10120090
PSB10120091
PSB10120092
PSB10120093
PSB10120094
PSB10120095
PR13M
PSB10120097
P6013
PSB10120099
PSB10120100

SPINDLE PULLEY
PULLEY WASHER 8MM
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 25
SPINDLE BOLT
SPINDLE
CAM LOCK SPRING
CAM LOCK
KEY 10 X 6 X 85
KEY 7 X 7 X 30
CAP SCREW M6-1 X 35
FRONT SPINDLE BEARING COVER
BEARING COVER GASKET
TAPERED ROLLER BEARING 32019 NTN
GEAR 79T
GEAR 36T
TAPERED ROLLER BEARING 30214A NTN
SPANNER NUT
EXT RETAINING RING 65MM
GEAR 42T
BALL BEARING 6013-OPEN
END CAP GASKET
OUTBOARD SPINDLE END CAP

-6-

PARTS

For Machines Mfg. Since 8/09

Model SB1014/SB1015 Parts

Headstock Transfer Gearing

107

106 105 34

109
110
111

108
34

112

110

113

112

105
109

115

114

34
116

128

112

118
119

115

117
66
120

115

110

122

126
121

121

123
124
125
127

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

34
66
105
106
107
108
109
110
111
112
113
114
115

PCAP01M
PR15M
PSB10120105
PSB10120106
PSB10120107
PK99M
PR12M
PORP021
PSB10120111
PSB10120112
PSB10120113
PSB10120114
PSB10120115

CAP SCREW M6-1 X 16
EXT RETAINING RING 30MM
GEAR FENDER WASHER 6MM
GEAR 21T
GEAR 42T
KEY 6 X 6 X 15
EXT RETAINING RING 35MM
O-RING 20.8 X 2.4 P21
GEAR SHAFT
GEAR SHAFT WASHER 6MM
GEAR 42T
GEAR SLEEVE 21T
O-RING SPACER

116
117
118
119
120
121
122
123
124
125
126
127
128

PSB10120116
PR09M
PSB10120118
PSB10120119
PSB10120120
PSB10120121
PSB10120122
PSB10120123
PORP044
PSB10120125
PCAP26M
PSB10120127
PSB10120128

GEAR SHAFT
EXT RETAINING RING 20MM
DOUBLED ENDED GEAR 12T/21T
GEAR SHAFT
GEAR 21T
SPLINE SHAFT SPACER
NEEDLE BEARING RNA-6904
SPLINE SHAFT
O-RING 43.7 X 3.5 P44
FLANGED BEARING END CAP
CAP SCREW M6-1 X 12
OIL SEAL 28 X 44 X 7
SQUARE HEAD DRAIN PLUG 1/2 PT

-7-

-8-

208

218

215
213 214

202

401

217

216

209

203

221

220

206

232

244

221

223 235
234
222 233
231

219

221

206

239

226

225
240

261

225

249

243

257

250

242

401

253

225
226

230

259

241

225
224
248
247

238

246

237

245

225

206

236

224

229
228
227
225
224
226

260

255 256

258

254

PARTS

211
206

211 212
210
206
401

207

201

203

204

205

206

251

252

401

Model SB1014/SB1015 Parts
For Machines Mfg. Since 8/09

Gearbox Gearing

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Gearbox Gearing Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231

PSB10120201
PSB10120202
PSB10120203
PSB10120204
PSB10120205
PR09M
PK109M
PSB10120208
PSB10120209
PSB10120210
PSB10120211
PSB10120212
PSB10120213
PSB10120214
PR11M
PSB10120216
PSB10120217
PSB10120218
PSB10120219
PSB10120220
PSB10120211
PSB10120222
PSB10120223
PSB10120224
PR23M
P6203-OPEN
PSB10120227
PSB10120228
PR06M
PSB10120230
PSB10120231

SPLINE SHAFT
OIL SEAL 20 X 32 X 5
SLEEVE BEARING TAF202820
SLEEVE BEARING HOUSING
SLEEVE BEARING SPACER
EXT RETAINING RING 20MM
KEY 7 X 7 X 35
DOUBLE GEAR 19/20T
SPLINE SHAFT
SPLINE SHAFT END CAP
BALL BEARING 16004
BEARING SPACER
DOUBLE-ENDED GEAR 19T/30T
GEAR SPACER
EXT RETAINING RING 25MM
SPLINE SHAFT
SPLINE SHAFT
WOODRUFF KEY 5 X 19
END CAP GASKET
GEARBOX CASTING
BALL BEARING 16004
CLUTCH GEAR 38T
DOUBLE ENDED CLUTCH GEAR 23T/19T
SPACER
INT RETAINING RING 40MM
BALL BEARING 6203-OPEN
CLUTCH RING
CLUTCH SPACER
EXT RETAINING RING 16MM
CLUTCH GEAR 35T
GEAR 22T

232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
401

PSB10120232
PSB10120233
PSB10120234
PSB10120235
PSB10120236
PSB10120237
PSB10120238
PSB10120239
PSB10120240
PSB10120241
PR10M
PSB10120243
PSB10120244
PSB10120245
PSB10120246
PSB10120247
PSB10120248
PR18M
PSB10120250
PSB10120251
PSB10120252
PSB10120202
PSB10120254
PSB10120255
PSB10120256
PSB10120257
PK15M
P6001-OPEN
PR03M
PSB10120261
PCAP26M

GEAR 19T
GEAR 20T
GEAR 24T
GEAR 23T
GEAR 27T
GEAR 24T
GEAR 28T
GEAR 26T
GEAR 38T
GEAR RETAINING NUT
EXT RETAINING RING 22MM
DOUBLE ENDED GEAR 36T/50T
GEAR 22T
GEAR 22T
GEAR 22T
GEAR 33T
GEAR 22T
EXT RETAINING RING 17MM
DOUBLE GEAR 20T/36T
END CAP SPACER
SPLINE SHAFT END CAP
OIL SEAL 20 X 32 X 5
SPLINE SHAFT
FLANGED SLEEVE BEARING
OIL SEAL 24 X 35 X 8
GEAR SHAFT
KEY 5 X 5 X 35
BALL BEARING 6001-OPEN
EXT RETAINING RING 12MM
FLANGED SLEEVE BEARING
CAP SCREW M6-1 X 12

-9-

-10-

415

275
264
273

271

274

279

277

280

403

272

404
405

268

270

266
267
268
269
268

312

311

309

264
265

263

308

407
300 302
307
415
262

406

297

281

313

417
408
306
302 306408
301
408
303
304

312

314

290

287
288 289

283 285
288
286

315

409

322

324

310

412

321

413

319
320

414

316 317
411 318

414

323

PARTS

281
278
276

402

416

305

282

293 284
294 295
296
298
297
299

282
283

291
292

Model SB1014/SB1015 Parts
For Machines Mfg. Since 8/09

Gearbox Controls

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Gearbox Controls Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300

PSB10120262
PSB10120263
PSB10120264
PSB10120265
PSB10120266
PSTB001
PSB10120268
PSB10120269
PSB10120270
PSB10120271
PSB10120272
PSB10120273
PSB10120274
PSB10120275
PSB10120276
PSB10120277
PSB10120278
PSB10120279
PSB10120277
PRP02M
PSB10120282
PSB10120283
PSB10120284
PSB10120285
PEC015M
PSB10120287
PR18M
PSB10120289
PSB10120290
PSB10120291
PSB10120292
PSB10120293
PSTB001
PSB10120295
PSB10120296
PSB10120297
PSB10120298
PSTB001
PSB10120300

GEARBOX COVER GASKET
PARTITION NUT
UPPER PLATE
UPPER FORK SUPPORT
COMPRESSION SPRING 4 X 19
STEEL BALL 1/4
PARTITION
MIDDLE FORK SUPPORT
LOWER FORK SUPPORT
BOTTOM FORK SUPPORT
REVERSE STOP PLATE
PARTITION SPACER
SHOULDER PLATE
LEFT CONNECTOR PLATE
RIGHT CONNECTOR PLATE
BOTTOM FORK
LOWER FORK
MIDDLE FORK
UPPER FORK
ROLL PIN 3 X 16
CONNECTOR PIN
PIVOT ARM
CAM
SHIFT BRACKET
E-CLIP 8MM
BRACKET SPACER
EXT RETAINING RING 17MM
WOODRUFF KEY 4 X 13
SHIFT ROD
STOP BLOCK
DOWEL PIN 5 X 24MM
RIGHT SHIFT FORK
STEEL BALL 1/4
COMPRESSION SPRING 6.25 X 18
STOP BLOCK
SHIFT ROCKER ARM
COMPRESSION SPRING 6 X 13
STEEL BALL 1/4
SHIFT SHAFT SUPPORT BAR

301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
402
403
404
405
406
407
408
409
411
412
413
414
415
416
417

PSB10120289
PSB10120302
PORP018
PSB10120304
PSB10120305
PRP24M
PSB10120128
PSB10120308
PSB10120309
PSB10120310
PSB10120311
PORG040
PSB10120313
PSB10120314
PSB10120315
PORG030
PSB10120317
PSB10120318
PSB10120319
PSB10120015
PSB10120321
PSB10120322
PSB10120323
PSB10120324
PCAP15M
PLW03M
PCAP26M
PCAP48M
PRP04M
PSS03M
PCAP02M
PCAP167M
PCAP38M
PCAP26M
PCAP33M
PS17M
PCAP66M
PSB10120416
PSB10120417

WOODRUFF KEY 4 X 13
SHIFT SHAFT
O-RING 17.8 X 2.4 P18
SHIFT SHAFT SLEEVE
SHIFT FORK
ROLL PIN 5 X 16
SQUARE HEAD PIPE PLUG 1/2 PT
PIPE ELBOW 90 DEG 1/2 X 1/2 PT
PIPE NIPPLE 1/2 X 1/2 PT X 1"
GEARBOX COVER
SELECTOR ROD
O-RING 39.4 X 3.1 G40
SELECTOR LEVER SUPPORT
COMPRESSION SPRING 9 X 38
SELECTOR LEVER
O-RING 3.1 X 29.4 G30
SELECTOR LEVER END CAP
SELECTOR PLATE
SHIFTING HANDLE
HANDLE WASHER 5MM
HANDLE CAP
OIL SIGHT GLASS
CONTROL PANEL
FEED CLUTCH COVER
CAP SCREW M5-.8 X 20
LOCK WASHER 6MM
CAP SCREW M6-1 X 12
CAP SCREW M6-1 X 35
ROLL PIN 4 X 24
SET SCREW M6-1 X 8
CAP SCREW M6-1 X 20
CAP SCREW M6-1 X 70
CAP SCREW M5-.8 X 25
CAP SCREW M6-1 X 12
CAP SCREW M5-.8 X 12
PHLP HD SCR M4-.7 X 6
CAP SCREW M8-1.25 X 65
TAPER PIN #3/#7 X 1/4"
SHIFT BRACKET SET SCREW

-11-

538

-12-

608

516

517

606

549

539

522

501

609

526
540

521
525

502
502

537

514

610

519

601

541

522

518

505

503
504

542
514

534
603

506

527

547

523

510

513

511
512

546

606

607

605

529 530

548

528

524

603

514
515

602

601

532

531
604

PARTS

545

544

509

520

535

508

507

Model SB1014/SB1015 Parts
For Machines Mfg. Since 8/09

Apron - Front View

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Apron - Front View Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528

PSB10120501
PSB10120502
PRP20M
PSB10120504
PSB10120505
PSB10120506
PSB10120507
PSB10120508
PSB10120509
PSB10120510
PSB10120511
PSB10120512
PSB10120513
PSTB001
PSB10120515
PSB10120516
PK14M
PSB10120518
PRP10M
PSB10120520
PR06M
PSB10120522
PORP018
PSB10120524
PRP04M
PSB10120526
PSB10120527
PORP016

DOUBLE GEAR 18T/60T
GEAR SPACER
ROLL PIN 4 X 22
DOUBLE GEAR 81T/60T
DOWEL PIN 4 X 17MM
DOUBLE GEAR 72T/60T
SLEEVE BEARING
BRACKET PLUG
FEED CONTROL BRACKET
OIL CUP
SPLINE SHAFT
FEED CONTROL HANDLE
FEED CONTROL WORM
STEEL BALL 1/4
COMPRESSION SPRING 6 X 16
GEAR SHAFT
KEY 5 X 5 X 18
INCH GEAR 81T
ROLL PIN 5 X 36
OIL SIGHT GLASS
EXT RETAINING RING 16MM
GEAR 18T
O-RING 17.8 X 2.4 P18
GEAR SHAFT
ROLL PIN 4 X 24
FEED DIRECTION PIVOT ARM
FEED DIRECTION SHAFT
O-RING 15.8 X 2.4 P16

529
530
531
532
534
535
537
538
539
540
541
542
544
545
546
547
548
549
601
602
603
604
605
606
607
608
609
610

PORP026
PSB10120530
PSB10120531
PSB10120532
PORP012
PSB10120535
PSB10120266
PSB10120538
PSB10120539
PSB10120218
PSB10120541
PSB10120542
PSB10120515
PSB10120545
PSB10120546
PSB10120547
PSB10120548
PSB10120549
PSS26M
PCAP79M
PSS20M
PCAP33M
PW03M
PCAP06M
PSS12M
PCAP01M
PW03M
PCAP38M

O-RING 25.7 X 3.5 P26
FEED DIRECTION SHAFT SLEEVE
FEED DIRECTION KNOB
DIRECTION PLATE
O-RING 11.8 X 2.4 P12
GEAR SHAFT
COMPRESSION SPRING 4 X 19
SUPPORT BRACKET
GEAR SHAFT 18T
WOODRUFF KEY 5 X 19
INCH GEAR SHAFT SLEEVE
INCH INDEX RING
COMPRESSION SPRING 6 X 16
HANDWHEEL
HANDWHEEL WASHER 6MM
HANDWHEEL HANDLE
HANDLE CAP SCREW
SAFETY PLATE
SET SCREW M5-.8 X 6
CAP SCREW M5-.8 X 35
SET SCREW M8-1.25 X 8
CAP SCREW M5-.8 X 12
FLAT WASHER 6MM
CAP SCREW M6-1 X 25
SET SCREW M6-1 X 25
CAP SCREW M6-1 X 16
FLAT WASHER 6MM
CAP SCREW M5-.8 X 25

-13-

-14-

568

611

569

613

550

573

514

559

613

567

612

582

522

573

574

561

581

575

614

555

580

563

577

579

578

562

556

576 608

554

553

566

565

PARTS

614

572

570

583

558

534

551

552

Model SB1014/SB1015 Parts
For Machines Mfg. Since 8/09

Apron - Rear View

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Apron - Rear View Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

514
522
534
550
551
552
553
554
555
556
558
559
561
562
563
565
566
567
568

PSTB001
PSB10120522
PORP012
PSB10120550
PSB10120551
PSB10120552
PSB10120553
PSB10120554
PSB10120555
PR11M
PSB10120558
PRP88M
PSB10120561
PSB10120562
PSB10120563
PSB10120289
PSB10120566
PSB10120567
PSB10120568

STEEL BALL 1/4
GEAR 18T
O-RING 11.8 X 2.4 P12
APRON FRONT PLATE
BEVEL GEAR 23T
THRUST BEARING NTB/AS-2542
APRON CASTING
NEEDLE BEARING NK29/30
BEARING SPACER
EXT RETAINING RING 25MM
GEAR 18T
ROLL PIN 5 X 22
GEAR 18T
GEAR SPACER
BEVEL GEAR 64T
WOODRUFF KEY 4 X 13
HALF-NUT LEVER SHAFT
OIL FENCE
HALF-NUT LEVER

569
570
572
573
574
575
576
577
578
579
580
581
582
583
608
611
612
613
614

PSB10120569
PSB10120046
PRP04M
PORP020
PSB10120574
PSB10120575
PSB10120576
PSB10120577
PSB10120578
PSB10120579
PSB10120580
PSB10120581
PSB10120582
PRP102M
PCAP01M
PS17M
PCAP03M
PSS02M
PCAP24M

HALF-NUT LEVER HUB
COMPRESSION SPRING 6 X 27
ROLL PIN 4 X 24
O-RING 19.8 X 2.4 P20
CLAMP STEP SCREW
CAM SHAFT
STEP PIN
PIVOT LEVER
RETAINING BLOCK
INCH HALF-NUT
HALF-NUT GIB
APRON CASTING BOTTOM COVER
OIL DRAIN PLUG 1/8 PT
ROLL PIN 4 X 36
CAP SCREW M6-1 X 16
PHLP HD SCR M4-.7 X 6
CAP SCREW M5-.8 X 8
SET SCREW M6-1 X 6
CAP SCREW M5-.8 X 16

-15-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Dial Indicator

Carriage Stop

751
801

701
702
804

802
803
805

703
809

705

704

810

811

707
753

806

807

812

708

808

754
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

701
702
703
704
705
707
708
751
753
754

PSB10120701
PSB10120702
PSB10120703
PSB10120704
PSB10120705
PSB10120707
PSB10120708
PCAP04M
PSS02M
PN03M

DIAL INDICATOR INDEX PLATE
PIVOT SHAFT
DIAL INDICATOR CASTING
KNURLED KNOB
DOUBLE-THREADED STUD
GEAR SPACER
DIAL GEAR 16T
CAP SCREW M6-1 X 10
SET SCREW M6-1 X 6
HEX NUT M8-1.25

801
802
803
804
805
806
807
808
809
810
811
812

PCAP71M
PRIV001M
PSB10120803
PSB10120804
PSB10120805
PSB10120806
PSB10120807
PSS10M
PSB10120809
PSS06M
PSB10120811
PSS14M

CAP SCREW M10-1.5 X 60
STEEL FLUTED RIVET 2 X 5MM
INCH INDEX RING
INCH MICROMETER DIAL
CARRIAGE STOP BODY
INCH THREADED STOP ROD
CLAMP PLATE
SET SCREW M10-1.5 X 20
COPPER PLUNGER
SET SCREW M8-1.25 X 16
DOG END SET SCREW M6.1 X 12
SET SCREW M8-1.25 X 12

-16-

PARTS

For Machines Mfg. Since 8/09

Model SB1014/SB1015 Parts

Compound Slide & Tool Post
902

901

903
904
924
907

906

905

908
955
916

909

952

956

910

921

922

920

958
911

919

951

915

957

923

912

916

954
917

914

953

913
959

918

912
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917

PSB10120901
PSB10120902
PSB10120903
PSB10120904
PSB10120905
PSB10120906
PSB10120907
PSB10120908
PSB10120909
PSB10120910
PSB10120911
PSB10120912
PSB10120913
PSB10120914
PSB10120915
P51101
PSB10120917

TOOL POST HANDLE
TURRET NUT
TURRET NUT COLLAR
TOOL POST BOLT
TOOL POST BODY
TOOL POST STUD
BEVELED PLUNGER
COMPRESSION SPRING 6 X 27
TOOL POST BASE
COMPOUND SLIDE
COMPOUND GIB
GIB ADJUSTMENT SCREW
COMPOUND SWIVEL BASE
CMOPOUND LEADSCREW NUT
COMPOUND LEADSCREW
THRUST BEARING 51101
INDEX PLATE

918
919
920
921
922
923
924
951
952
953
954
955
956
957
958
959

PSB10120918
PSB10120919
PSB10120920
PSB10120921
PSB10120922
PSB10120923
PSB10120924
PCAP01M
PSS04M
PCAP26M
PRIV001M
PSS14M
PLUBE001
PSTB001
PSS14M
PSS03M

LEADSCREW SUPPORT BRACKET
DUAL INDEX RING
WAVY WASHER 35 X 45 X 0.3
LEADSCREW BEARING HOUSING
BALL HANDLE
HANDLE
TOOL POST BOLT KEY
CAP SCREW M6-1 X 16
SET SCREW M6-1 X 12
CAP SCREW M6-1 X 12
STEEL FLUTED RIVET 2 X 5MM
SET SCREW M8-1.25 X 12
TAP-IN BALL OILER 1/4
STEEL BALL 1/4
SET SCREW M8-1.25 X 12
SET SCREW M6-1 X 8

-17-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Saddle Body & Controls
1001

1002
1101

1016

1102

1103

1003

1104
1105
1004

1008
1009

1005

1010

1017

1001

1006
1007

1107
1013A
1019
1108

1009

1014

1015

1018
1025

1008

1023

1024

1106

1106
1110

1109
1022
1051

1024
1111

1025

1026

1101

1028
1029
1027
1030
1031

1106
1032

1112
1030

1113
1038

1036
1033

1039

1028
1040
1001
1114

-18-

1029

1034
1035

1102

1037

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Saddle Body & Controls Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1013A
1014
1015
1016
1017
1018
1019
1022
1023
1024
1025
1026
1027
1028
1029
1030

PSB10121001
PSB10121002
PSB10121003
PSB10121004
PSB10121005
PSB10121006
PSB10121007
PSB10121008
PSB10121009
PSB10121010
PSB10121013A
PK165M
PRP28M
PSB10121016
PSB10121017
PSB10121018
PSB10121019
PSB10121022
PSB10121023
PSB10121024
PSB10121025
PSB10121026
PSB10121027
PSTB001
PSB10121029
PSB10121030

CROSS GIB ADJUSTMENT SCREW
CROSS SLIDE
PIVOT STUD 18 X 28
COMPOUND T-BOLT
CROSS SLIDE GIB
CROSS WAY WIPER
CROSS WAY WIPER PLATE
THRUST BEARING NTB/AS2-1226
BEARING COLLAR
LEADSCREW SLEEVE BEARING
CROSS LEADSCREW W/NUT ASSY
KEY 3 X 3 X 100
ROLL PIN 5 X 40
COOLANT NOZZLE 3/8 PT X 24"
COOLANT STAND PIPE/VALVE 3/8 PT
CROSS LEADSCREW END BRACKET
SADDLE
SADDLE OIL FILL PLUG
TAPER PIN #6 X #2 X 3/4"
BEDWAY WIPER
BEDWAY WIPER PLATE
PINION 160DP 16T
PINION BRACKET
STEEL BALL 1/4
COMPRESSION SPRING 6 X 15
THRUST BEARING NTB/AS2 1730

1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1051
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114

PSB10121031
PSB10121032
PSB10121033
PSB10121034
PSB10121035
PSB10121036
PSB10121037
PSB10121038
PSB10121039
PSB10121040
PSB10121051
PLUBE001
PSS28M
PCAP07M
PN02M
PW04M
PS08M
PCAP06M
PN02M
PCAP02M
PCAP35M
PSS03M
PCAP17M
PCAP02M
PCAP02M

BEARING CAP 18 X 52 X 4
INDEX DIAL HOUSING
DUAL INDEX RING
CARRIAGE HANDWHEEL
HANDWHEEL WASHER 6MM
HANDWHEEL HANDLE
HANDWHEEL HANDLE SCREW
SADDLE GIB
REAR GIB PRESSURE BAR
FRONT GIB PRESSURE BAR
SADDLE OIL PUMP ASSEMBLY
TAP-IN BALL OILER 1/4
SET SCREW M6-1 X 30
CAP SCREW M6-1 X 30
HEX NUT M10-1.5
FLAT WASHER 10MM
PHLP HD SCR M5-.8 X 12
CAP SCREW M6-1 X 25
HEX NUT M10-1.5
CAP SCREW M6-1 X 20
CAP SCREW M8-1.25 X 60
SET SCREW M6-1 X 8
CAP SCREW M4-.7 X 10
CAP SCREW M6-1 X 20
CAP SCREW M6-1 X 20

-19-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Saddle Base
1048

1042

1045

1043

1041

1047

1046

1115

1046

1113

1044
1111

1049

1050

1044

1106

1051
1052
1116

1117

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1041
1042
1043
1044
1045
1046
1047
1048
1049

PSB10121041
PSB10121042
PSB10121043
PSB10121044
PSB10121045
PSB10121046
PSB10121047
PSB10121048
PSB10121049

GEAR WASHER 5MM
GEAR 16T
GEAR SHAFT
STRAIGHT PIPE ADAPTER 1/8 PT X 4MM
ALUMINUM TUBE 4 X 260MM
ELBOW ADAPTER 1/8 PT X 4MM
ALUMINUM TUBE 4 X 120MM
OIL FILTER 6MM
ALUMINUM TUBE 6 X 160MM

1050
1051
1052
1106
1111
1113
1115
1116
1117

PSB10121050
PSB10121051
PSB10121052
PS08M
PSS03M
PCAP02M
PCAP24M
PSS74M
PCAP169M

STRAIGHT PIPE ADAPTER 1/8 PT X 6MM
SADDLE OIL PUMP ASSEMBLY
SUPPORT BRACKET
PHLP HD SCR M5-.8 X 12
SET SCREW M6-1 X 8
CAP SCREW M6-1 X 20
CAP SCREW M5-.8 X 16
SET SCREW M8-1.25 X 35
CAP SCREW M12-1.75 X 75

-20-

1327

1325

1324

1323

1311

1328

1326

1324

1321

1223A

1315
1310
1222

1231

1219

1238

1212

1215

1221

1309

1214

1217
1216

1213

1218

1230

1211

1210

1306

1318

1202

1206
1205

1318
1304

1303
1302 1207

1204
1305

1307

1227

1208
1229
1228

1314

1313

1209

1319
1220
1308

1318

1228

1237

1201

1301

1203

1316

1317

PARTS

1322

1320

1234
1235
1218
1232
1225

1312

1226

1236

1316

1317

For Machines Mfg. Since 8/09
Model SB1014/SB1015 Parts

Bed & Shafts

-21-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Bed & Shafts Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223A
1225
1226
1227
1228
1229
1230
1231
1232
1234

PSB10141201
PSB10121202
PSB10121203
PSB10121204
PSTB002
PSB10121206
PSB10121207
PSB10121208
PSB10121209
PSB10121210
PSB10121211
PSB10121212
PSB10121213
PSB10121214
PSB10121215
PSB10121216
PSB10121217
PR37M
PSB10141219
PSB10121220
PSB10141221
PSB10121222
PSB10121223A
P51203
PSB10121226
PSB10121227
P51105
PSB10121229
PSB10141230
PSB10121231
PSB10121232
PSB10121234

BED CASTING
BED END STOP BOLT
SHAFT END BRACKET COVER
FEED ROD END BRACKET
STEEL BALL 5/16
COMPRESSION SPRING 8 X 27
SPINDLE ROD END BRACKET
SHAFT END BRACKET
LOCK COLLAR
SPINDLE LEVER HUB
STEP PIN
SPINDLE ROD LEVER
SPINDLE ROD LEVER KNOB
SPINDLE LEVER HUB BRACKET
SPINDLE ROD SLEEVE
COMPRESSION SPRING 38 X 75
SPRING HOUSING
EXT RETAINING RING 32MM
SPINDLE ROD
THRUST BEARING NTB/AS2 1831
FEED ROD
FEED ROD LOCK COLLAR
CLUTCH COLLAR ASSEMBLY
THRUST BEARING 51203
COMPRESSION SPRING 9 X 32
LEADSCREW LOCK NUT
THRUST BEARING 51105
OIL FILL PLUG
INCH LEADSCREW 4 TPI
LEADSCREW SLEEVE BEARING
COMPRESSION SPRING 27 X 55
LEADSCREW SHEAR PIN

1235
1236
1237
1238
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328

PSB10121235
PSB10121236
PSB10141237
PSB10141238
PCAP83M
PSS11M
PCAP06M
PSS30M
PCAP128M
PSB10121306
PSB10121307
PCAP40M
PN09M
PK20M
PCAP02M
PSB10121312
PRP93M
PCAP02M
PSS02M
PW06M
PB24M
PSS03M
PSB10121319
PSB10141320
PCAP13M
PSB10141322
PSS09M
PSB10141324
PSB10141325
PSS06M
PSB10141327
PSS20M

SHEAR PIN WASHER
SHEAR PIN COLLAR
LONGITUDINAL RACK
GAP RACK
CAP SCREW M6-1 X 55
SET SCREW M6-1 X 16
CAP SCREW M6-1 X 25
SET SCREW M10-1.5 X 10
CAP SCREW M8-1.25 X 70
TAPER PIN #7 X #3 X 1/4"
DOWEL PIN #2 X 2"
CAP SCREW M8-1.25 X 35
HEX NUT M12-1.75
KEY 5 X 5 X 15
CAP SCREW M6-1 X 20
DOWEL PIN 4 X 30MM
ROLL PIN 6 X 25
CAP SCREW M6-1 X 20
SET SCREW M6-1 X 6
FLAT WASHER 12MM
HEX BOLT M12-1.75 X 45
SET SCREW M6-1 X 8
FEED ROD LOCK COLLAR
ADJUSTMENT STEP BOLT
CAP SCREW M8-1.25 X 30
TOP BEDWAY CLAMP
SET SCREW M8-1.25 X 20
PLUNGER
BOTTOM BEDWAY CLAMP
SET SCREW M8-1.25 X 16
LEADSCREW STABILIZER BODY
SET SCREW M8-1.25 X 8

-22-

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

End Gears

1405

1414

1404

1413
1412

1403
1402
1401

1415

1410

1406
1407

1406

1408

1411

1419

1409
1408

1407
1406
1418

1417 1416

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1401
1402
1403
1404
1405
1406
1407
1408
1409
1410

PCAP02M
PSB10121402
PSB10141403
PSB10141404
PK166M
PN32M
PSB10121407
PR25M
PSB10141409
P6005ZZ

CAP SCREW M6-1 X 20
GEAR WASHER 6MM
GEAR 24T
PIVOT ARM
KEY 7 X 7 X 15
HEX NUT M14-2
GEAR WASHER 14MM
INT RETAINING RING 47MM
DOUBLE GEAR 44T/56T
BALL BEARING 6005ZZ

1411
1412
1413
1414
1415
1416
1417
1418
1419

PSB10121411
PSB10121412
PSB10121413
PK28M
PSB10121415
PCAP14M
PSB10121417
PSB10141418
PSB10121419

BEARING SPACER
GEAR SHAFT BUSHING
GEAR SHAFT
KEY 7 X 7 X 30
PIVOT ARM STUD
CAP SCREW M8-1.25 X 20
GEAR WASHER 8MM
GEAR 57T
GEAR BUSHING

-23-

-24-

1536

1520

1534
1533
1531
1532

1533

1531

1533

1502

1535

1524

1529

1523

1518
1512
1513

1526

1511
1510
1506
1527

1516

1514
1515

1517

1516
1528 1523
1525
1530

1530

1519

1519-2

1522

1519-1

1521

1506

1507

1509

1508

1519-3

1501

1502

1505

1504

1503

1502

PARTS

1537

1538

1502

Model SB1014/SB1015 Parts
For Machines Mfg. Since 8/09

Motor Assembly

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Motor Assembly Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1519-1
1519-2

PSB10121501
PN02M
PW04M
PSB10121504
PSB10121505
PCAP64M
PSB10121507
PVB69
PSB10121509
PCAP01M
PSB10121511
PSB10121512
PEC09M
PSB10121514
PCAP45M
PW01M
PSB10121517
PSB10121518
PSB10141519
PSB10141519-1
PSB10141519-2

SIDE COVER MOUNTING PIN
HEX NUT M10-1.5
FLAT WASHER 10MM
LEFT TOP SIDE COVER
KNURLED SIDE COVER KNOB M10-1.5
CAP SCREW M10-1.5 X 25
PULLEY WASHER 10 X 39 X 5MM
V-BELT B69
MOTOR PULLEY
CAP SCREW M6-1 X 16
TAPER PIN #4 X #1 X 3/4"
BRAKE BELT BRACKET
E-CLIP 6MM
BRAKE BELT ADJUSTMENT BAR
CAP SCREW M8-1.25 X 45
FLAT WASHER 8MM
BRAKE BELT
CAPTIVE PIN
MOTOR 7-1/2HP 220/440V 3PH 60HZ
MOTOR FAN COVER
MOTOR FAN

1519-3
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538

PSB10141519-3
PSB10121520
PS68M
PSB10121522
PN03M
PSB10121524
PSB10121525
PCAP60M
PSB10121527
PSB10121528
PB31M
PLW06M
PN13M
PSB10121532
PW08M
PSB10121534
PSB10121535
PN04M
PSB10121537
PS65M

MOTOR JUNCTION BOX
SIDE COVER MOUNTING STUD
PHLP HD SCR M6-1 X 10
MOTOR COVER
HEX NUT M8-1.25
SPRING MOUNTING STUD
BRAKE BELT EXTENSION SPRING
CAP SCREW M8-1.25 X 55
MOUNTING INSERT
MOTOR MOUNTING 10T/395 X 300MM
HEX BOLT M10-1.5 X 40
LOCK WASHER 10MM
HEX NUT M16-2
ALL-THREAD STUD M16-2 X 170
FLAT WASHER 16MM
RUBBER CUSHION SLEEVE
MOTOR SUPPORT SHAFT
HEX NUT M4-.7
SIDE COVER SAFETY SWITCH TM1307
PHLP HD SCR M4-.7 X 40

-25-

-26-

1616

1609
1608

1628

1626
1625

1605

1614

1624

1612

1603 1602
1610

1604

1611

1612
1606

1613
1603 1612 1614

1618

1639

1619

1632

1634
1640
1633
1634 1642
1636
1637
1638

1630

1654

1655

1643

1622

1614

1620

1621

1623

1644

1645

1603

1648

1649

1612

1646

1647

1652
1650

1653

1651

PARTS

1601

1612
1617

1627

1603

1631 1635

1629

Model SB1014/SB1015 Parts
For Machines Mfg. Since 8/09

Cabinets & Panels

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Cabinets & Panels Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1601
1602
1603
1604
1605
1606
1608
1609
1610
1611
1612
1613
1614
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628

PSB10141601
PSB10121602
PCAP01M
PB56M
PSB10141605
PSB10141606
PSB10121608
PSB10121609
PSB10121610
PSB10121611
PCAP64M
PSB10121613
PW04M
PSB10121616
PSB10121617
PS05M
PSB10121619
PSB10121620
PSB10121621
PCAP02M
PSS01M
PSB10141624
PFH30M
PSB10121626
PSB10121627
PSS14M

CHIP TRAY
BRAKE CAM
CAP SCREW M6-1 X 16
CAP SCREW M10-1.5 X 20
BRAKE FOOT PEDAL
BRAKE SHAFT
LOCK COLLAR
BRAKE SHAFT BRACKET
RIGHT CABINET
RIGHT FRONT CABINET COVER
CAP SCREW M10-1.5 X 25
CHIP TRAY L-BRACKET
FLAT WASHER 10MM
LEFT CABINET
LEFT FRONT CABINET COVER
PHLP HD SCR M5-.8 X 8
RIGHT GEARBOX COVER
SPLASH PAN SUPPORT BRACKET
SPLASH PAN ROD BRACKET
CAP SCREW M6-1 X 20
SET SCREW M6-1 X 10
SPLASH PAN ROD
FLAT HD SCR M5-.8 X 8
ELECTRICAL CABINET BACK PLATE
CHUCK GUARD BRACKET
SET SCREW M8-1.25 X 12

1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655

PSB10121629
PSB10121630
PSB10121631
PN06
PB102
PCAP26M
PN04M
PLW03M
PSB10121637
PSB10121638
PS65M
PSS34M
PN03M
PSB10141643
PSB10121644
PS68M
PSB10121646
PSB10121647
PSB10121648
PSB10121649
PW17
PN43
PSB10141652
PSB10121653
PSB10121654
PB80M

CHUCK GUARD ROD
CHUCK GUARD
KNOB 1/2-13
HEX NUT 1/2-13
HEX BOLT 1/2-13 X 3/4
CAP SCREW M6-1 X 12
HEX NUT M4-.7
LOCK WASHER 6MM
SAFETY SWITCH BRACKET
CHUCK GUARD SAFETY SWITCH
PHLP HD SCR M4-.7 X 40
SET SCREW M5-.8 X 16
HEX NUT M8-1.25
SPLASH GUARD
REAR CABINET COVER
PHLP HD SCR M6-1 X 10
COOLANT RESERVOIR
COOLANT PUMP
HOSE CONNECTOR 1/8 PT X 3/8 PH
COOLANT HOSE CT801 3/8 X 78"
FLAT WASHER 1"
HEX NUT 1-12
CABINET SUPPORT ROD
COOLANT RETURN CHUTE
CAST IRON FOOT PAD
HEX BOLT M16-2 X 55

-27-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Headstock Oiling System
1736
1737

1707

1706 1705
1704

1701
1710

1709 1708

1729

A
B

1711
1712

1737

1713

1738
1735

1714
D

1735

1734

1715

1734
1716

1739

1730

1733
1731
1732

1715

1725-3
1725-1

1721

1725

1701
E

1725-2

1717
D

1726
1724
1727
1728

-28-

1722
1723

1718

1719

1720

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Headstock Oiling System Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1701
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
1722

PSB10121701
PCAP50M
PW02M
PSB10121706
PSB10121707
PS34
PSB10121709
PN07M
PSB10121711
PRP02M
PSB10121713
PSB10121714
PSB10121715
PSB10121716
PCAP02M
PN01M
PCAP04M
PSB10121720
PSB10121721
PSB10121722

ELBOW CONNECTOR
CAP SCREW M5-.8 X 10
FLAT WASHER 5MM
PIPE CLAMP 10MM
SENSOR BRACKET
PHLP HD SCR M3-.5 X 25
SPINDLE SPEED SENSOR
HEX NUT M3-.5
MINOR TIP
ROLL PIN 3 X 16
SPINDLE BALANCE RING
HEADSTOCK OIL DRAIN SCREEN
HOSE CLAMP 1-3/4"
OIL RETURN HOSE 1-1/4 X 17"
CAP SCREW M6-1 X 20
HEX NUT M6-1
CAP SCREW M6-1 X 10
OIL RESERVOIR COVER 129.5MM
OIL PRESSURE SWITCH
PIPE T-JOINT 1/4 PT

1723
1724
1725
1725-1
1725-2
1725-3
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739

PSB10121723
PSB10121724
PSB10121725
PSB10121725-1
PSB10121725-2
PSB10121725-3
PSB10121726
PSB10121727
PSB10121728
PSB10121729
PSB10121730
PSB10121731
PSB10121732
PSB10121733
PW03M
PCAP01M
PCAP14M
PW01M
PN03M
PSB10121739

PIPE CONNECTOR 1/4 PT X 1/4 PT
LUBRICATION PUMP
LUBRICATION MOTOR 1/4HP 220V 3PH
MOTOR FAN COVER
MOTOR FAN
MOTOR JUNCTION BOX
ELBOW CONNECTOR 3/8 PT X 1/4 PT
RUBBER RING 3/8"
STAND PIPE 3/8 PT X 8"
NYLON OIL DELIVERY TUBE 10 X 100MM
OIL RESERVOIR FILL CAP 1 PT
OIL LEVEL GLASS 3"
OIL DRAIN PLUG 3/4 PT
OIL RESERVOIR
FLAT WASHER 6MM
CAP SCREW M6-1 X 16
CAP SCREW M8-1.25 X 20
FLAT WASHER 8MM
HEX NUT M8-1.25
ELECTRICAL CABINET

-29-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Tailstock
1801

1803
1805
1901

1804

1806

1807
1808

1809

1814
1813
1810
1902

1815
1821

1822

1903

1816

1819

1811
1812

1817
1818

1819
1905
1904

1825

1823
1824

1905
1828
1830
1829

1826

1802

1914
1906

1913

1908

1832
1831

1834

1833

1834
1837
1832
1838

1911

1827
1909
1915

1839
1840
1911
1912

-30-

1910

1908

1907

For Machines Mfg. Since 8/09

PARTS

Model SB1014/SB1015 Parts

Tailstock Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811
1812
1813
1814
1815
1816
1817
1818
1819
1821
1822
1823
1824
1825
1826
1827

PSB10121801
PSB10121802
PK34M
PSB10121804
PSB10121805
PR37M
PSB10121807
PSB10121808
PSB10121809
PSB10121810
PSB10121811
PSB10121812
PSB10120515
PSTB001
PSB10121815
PSB10121816
PSB10121817
PSB10121818
PRP04M
PSB10121821
PLUBE001
PSB10141823
PSB10121824
PSB10121825
PSB10121826
PSB10121827

INCH TAILSTOCK LEADSCREW
INCH LEADSCREW NUT
KEY 5 X 5 X 20
THRUST BEARING MTB/AS2-2035
INCH LEADSCREW FLANGE BRACKET
EXT RETAINING RING 32MM
INDEX DIAL SPACER
INCH INDEX RING
HANDWHEEL
HANDWHEEL WASHER 6MM
HANDLE BOLT M8-1.25 X 90
HANDWHEEL HANDLE
COMPRESSION SPRING 6 X 16
STEEL BALL 1/4
QUILL LOCK LEVER
QUILL LOCK CAM SHAFT
TAILSTOCK LOCK LEVER
TAILSTOCK LOCK CAM SHAFT
ROLL PIN 4 X 24
OIL SEAL DH53
TAP-IN BALL OILER 1/4
TAILSTOCK CASTING
TAILSTOCK QUILL
QUILL GUIDE KEY
TOP OFFSET INDEX PLATE
BOTTOM OFFSET INDEX PLATE

1828
1829
1830
1831
1832
1833
1834
1837
1838
1839
1840
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
1911
1912
1913
1914
1915

PSB10121828
PSB10121829
PSB10141830
PSB10121831
PSB10121832
PSB10121833
PSB10121834
PSB10121837
PSB10121838
PSB10121839
PSB10121840
PCAP01M
PSS04M
PCAP26M
PCAP128M
PCAP35M
PCAP68M
PCAP01M
PS08M
PW04M
PB144M
PW10M
PN32M
PN03M
PRIV001M
PLW06M

TAILSTOCK ALIGNMENT PIN
PIVOT BLOCK
DOG POINT SET SCREW M8-1.25 x 50
TAILSTOCK BASE
GIB ADJUSTMENT SCREW
BEDWAY WIPER
BEDWAY WIPER PLATE
TAILSTOCK GIB
COMPRESSION SPRING 25 X 45
CLAMP BLOCK
TAILSTOCK STUD M14-2 X 110
CAP SCREW M6-1 X 16
SET SCREW M6-1 X 12
CAP SCREW M6-1 X 12
CAP SCREW M8-1.25 X 70
CAP SCREW M8-1.25 X 60
CAP SCREW M6-1 X 8
CAP SCREW M6-1 X 16
PHLP HD SCR M5-.8 X 12
FLAT WASHER 10MM
HEX BOLT M10-1.5 X 55
FLAT WASHER 14MM
HEX NUT M14-2
HEX NUT M8-1.25
STEEL FLUTED RIVET 2 X 5MM
LOCK WASHER 10MM

-31-

Model SB1014/SB1015 Parts

Steady Rest
2001
2002
2012A

For Machines Mfg. Since 8/09

PARTS

Follow Rest
2101

2003

2102

2004
2006
2009

2005

2108A

2104

2007

2010

2105

2008
2012

2011

2103

2107

2106

2014

2015
2016

2013

2017
2108

2018
2019

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2012A
2013
2014
2015
2016
2017
2018
2019

PSB10122001
PRP51M
PSB10122003
PSB10122004
PSB10122005
PSB10122006
P627ZZ
PSS20M
PSB10122009
PSB10122010
PSB10122011
PSB10142012
PSB10142012A
PSB10142013
PSB10122014
PSB10122015
PN09M
PLW05M
PSB10122018
PSB10122019

FINGER ADJUSTMENT KNOB
ROLL PIN 4 X 40
FINGER COLLAR
FINGER STUD
STEADY REST FINGER
BEARING DOWEL PIN
BALL BEARING P627ZZ
SET SCREW M8-1.25 X 8
CLAMP STUD KNOB
CLAMP STUD
CLAMP STUD DOWEL PIN
TOP STEADY REST CASTING
STEADY REST ASSEMBLY
BOTTOM STEADY REST CASTING
HINGE PIN
SINGLE WING SCREW
HEX NUT M12-1.75
LOCK WASHER 12MM
STUD M12-1.75 X 75
CLAMP PLATE

2101
2102
2103
2104
2105
2106
2107
2108
2108A

PSB10122001
PRP51M
PSB10122003
PSB10122104
PSB10122105
PSB10122106
PSS20M
PSB10142108
PSB10142108A

FINGER ADJUSTMENT KNOB
ROLL PIN 4 X 40
FINGER COLLAR
FINGER STUD
FOLLOW REST FINGER
FINGER TIP
SET SCREW M8-1.25 X 8
FOLLOW REST CASTING
FOLLOW REST ASSEMBLY

-32-

PARTS

For Machines Mfg. Since 8/09

Model SB1014/SB1015 Parts

Electrical Cabinet & Control Panel
Electrical Cabinet
2201

2202

2212

2204

2205
2206

2203

2207

2225
2210

2215

2213
2223

2224

2209

2208

2212

2211

2226
2214

Control Panel

2217

2218

2219

2220

2221

2222

-33-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Electrical Cabinet & Control Panel Parts List
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

2201
2201
2202
2203
2204
2205
2206
2206
2207
2208
2209
2209
2210
2211

PSB10142201
PSB10152201
PSB10122202
PSB10122203
PSB10122204
PSB10122205
PSB10142206
PSB10152206
PSB10122207
PSB10122208
PSB10122209
PSB10132209
PSB10122210
PSB10122211

RESISTOR 800W 20-OHM (SB1014)
RESISTOR 600W 100-OHM (SB1015)
CABINET COOLING FAN
CIRCUIT BREAKER 20A
TRANSFORMER 24-440V
MAIN POWER SWITCH
INVERTER YASKAWA CIMR-G7A25P5 (SB1014)
INVERTER YASKAWA CIMR-G7A45P5 (SB1015)
CONTACTOR AB 100-C1001 24V
OL RELAY AB 193-TAA40 0.24-0.4A
OL RELAY AB 193TAB24 1.6-2.5A (SB1014)
OL RELAY AB 193TAB10 0.6-1.0A (SB1015)
CIRCUIT BOARD
TERMINAL BLOCK 3-POST 30A

2212
2213
2214
2215
2217
2218
2219
2220
2221
2222
2223
2224
2225
2226

PSB10122212
PSB10122213
PSB10122214
PSB10122215
PSB10122217
PSB10122218
PSB10122219
PSB10122220
PSB10122221
PSB10122222
PSB10122223
PSB10122224
PSB10122225
PSB10122226

WIRE LOOM 17"
WIRE LOOM 16"
WIRE LOOM 14"
WIRE LOOM 12"
TACHOMETER DISPLAY
SPINDLE SPEED DIAL
POWER LAMP ASSEMBLY
COOLANT PUMP SWITCH
SPINDLE JOG BUTTON
EMERGENCY STOP BUTTON
RELAY OMRON MY4NJ 24VAC
RELAY OMRON NY2NJ 24VAC
CIRCUIT BREAKER 6A
TERMINAL BLOCK 3-POST 15A

-34-

PARTS

For Machines Mfg. Since 8/09

Model SB1014/SB1015 Parts

Accessories
2303

2302-2

2301-2

2304

2301-1
2305

2307

2302-1

2308

2310

2301-3

2306

2309
2301

2302

2311
2312
2313

2316

2314
2315

2317

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

2301
2301-1
2301-2
2301-3
2302
2302-1
2302-2
2303
2304
2305
2306

PSB10122301
PSB10122301-1
PSB10122301-2
PSB10122301-3
PSB10122302
PSB10122302-1
PSB10122302-2
PSB10122303
PSB10122304
PSB10122305
PSB10122306

4-JAW CHUCK 10" ASSEMBLY
4-JAW CHUCK 10"
4-JAW CHUCK JAW SET
4-JAW CHUCK CAMLOCK STUD SET
3-JAW CHUCK 8" ASSEMBLY
3-JAW CHUCK 8"
3-JAW CHUCK STANDARD JAW SET
FACEPLATE ASSEMBLY 12"
3-JAW CHUCK KEY
4-JAW CHUCK KEY
TOOL POST T-WRENCH

2307
2308
2309
2310
2311
2312
2313
2314
2315
2316
2317

PSB10122307
PSB10122308
PSB10122309
PSB10122310
PWR1012
PWR1417
PWR2224
PSDF2
PSDP2
PAW1510M
PSB10122317

STANDARD DEAD CENTER MT#4
CARBIDE TIP DEAD CENTER MT#4
SPINDLE SLEEVE MT#4/MT#6
3-JAW CHUCK REVERSIBLE JAW SET
WRENCH 10/12MM
WRENCH 14/17MM
WRENCH 22/24MM
SCREWDRIVER FLAT #2
SCREWDRIVER PHILLIPS #2
HEX WRENCH SET 10PC 1.5-10 MM
TOOLBOX

-35-

Model SB1014/SB1015 Parts

For Machines Mfg. Since 8/09

PARTS

Machine Labels (Front View)
2410

2411

2404

2405
2409

2412

2415
2408

2413

2417

2416

2418

2414

2404

2406

2401

2407

2405
2402

2403
REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

2401
2402
2403
2404
2405
2406
2407
2407
2408
2409

PSB10122401
PSB10122402
PSB10122403
PSBLABEL08HS
PSBLABEL04HS
PSB10122406
PSB10142407
PSB10152407
PSB10122408
PSB10122409

RELEASE BOLT NOTICE LABEL
THREAD DIAL CHART LABEL
ONE-SHOT OILER LABEL
ENTANGLEMENT HAZARD LABEL
EYE INJURY HAZARD LABEL
AUTHORIZED PERSONNEL NOTICE LABEL
MACHINE ID LABEL (SB1014)
MACHINE ID LABEL (SB1015)
CHANGING SPEED NOTICE LABEL
CHANGING GEARS LABEL

2410
2411
2412
2413
2414
2415
2416
2416
2417
2418

PSBLABEL01HS
PSB10122411
SBPPAINT-01
PSBPAINT02
PSBPAINT03
PSB10142415
PSB10142416
PSB10152416
PSB10122417
SB1322

READ MANUAL LABEL
CHUCK KEY HAZARD LABEL
SB GRAY TOUCH-UP PAINT
SB LIGHT BLUE TOUCH-UP PAINT
SB DARK BLUE TOUCH-UP PAINT
TOOL ROOM SERIES LABEL
MODEL NUMBER LABEL (SB1014)
MODEL NUMBER LABEL (SB1015)
SB LATHE CO LABEL
SOUTH BEND NAMEPLATE 255MM

The safety labels provided with your machine are used to make the operator aware of the
machine hazards and ways to prevent injury. The owner of this machine MUST maintain the
original location and readability of these safety labels. If any label is removed or becomes
unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at
(360) 734-1540 or www.southbendlathe.com to order new labels.
-36-

PARTS

For Machines Mfg. Since 8/09

Model SB1014/SB1015 Parts

Machine Labels (Rear View)
2419

2420
2421

2425

2419

2419
2419

2422

2423

2420

2424

REF

PART #

DESCRIPTION

REF

PART #

DESCRIPTION

2419
2420
2421
2422

PSBLABEL01HS
PSBLABEL15M
PSB10122421
PSBLABEL06HS

DISCONNECT POWER LABEL
ELECTRICITY LABEL
ELECTRICAL CABINET LATCH LABEL
BIOHAZARD LABEL

2423
2423
2424
2425

PSB10122423
PSB10132423
PSB10122424
PSB10142425

220V 3-PHASE LABEL (SB1014)
440V 3-PHASE LABEL (SB1015)
INVERTER WARNING LABEL
MOTOR SPECIFICATIONS PLATE

-37-

South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
PHONE: (360) 734-1540 (Administrative Offices)
FAX: (360) 676-1075 (International)
FAX: (360) 734-1639 (USA only)

southbendlathe.com

Printed In Taiwan

#TS12318

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23
Create Date                     : 2011:03:14 13:42:28-07:00
Metadata Date                   : 2011:06:22 11:00:50-07:00
Modify Date                     : 2011:06:22 11:00:50-07:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Instance ID                     : uuid:b58aa254-968f-0d47-9798-04ca669cdf49
Document ID                     : adobe:docid:indd:e8129726-38c6-11df-95cc-c66c9a94fded
Rendition Class                 : proof:pdf
Derived From Instance ID        : afc266cd-37eb-11df-885a-e86e89cfabf9
Derived From Document ID        : adobe:docid:indd:7d3f9f94-fdd6-11de-8d45-8ac8568550d3
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 854.32, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 304.80, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 854.32, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 304.80, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 72.00, 300.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:5220C9F6E00611DE8177D03C91500349, uuid:7f2aff71-40ed-574f-8b4b-cf82766a96ef, uuid:448bf4ff-d8f0-6245-bb41-7792f204bf6b, uuid:7d05cb1e-4402-844a-bc7e-85f0d68a82af, uuid:c92173eb-602f-d740-b93a-2249a40112ef, uuid:B2C3B43DBB18DF119F94E5AD49C5B753, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:1E992BA04721DF11B8B990052AE8211F, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3157dbe1-eb06-8645-8efd-dbecdec1142e, uuid:eb6717ee-b0bc-e84a-9573-5d00b9e3b67f, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:e9e94272-c5ef-5c42-97b3-1eeaf2063109, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:8a93fcea-aa4f-a143-9bd1-e65d40093316, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:F7ABC767B40CDF11A4CF8C80CD954A61, uuid:84757047-02a3-d94a-b711-4abfb9a5f4c2, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:7c9e4a7d-fd86-9a4a-bbaa-bd60660e6a86, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:480e4259-01ce-2e4f-98a3-59a5065eebfb, uuid:2ebfc213-1ee4-934b-a56b-6dbf7c5d14c4, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:c57811b2-7587-4424-88e3-3f8671cc8a7a, uuid:bdfd12e4-727b-ec4c-9d93-a24e453ac89e, uuid:2333a99f-83fa-9a46-95c6-7327175bf5ce, uuid:8D05507ABA0CDF11A4CF8C80CD954A61, uuid:24149677-d473-a644-aefb-afd454189545, uuid:06c1ed60-558a-a145-b06e-2ad0ebe67ead, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:94ad7551-0bc1-2d4d-9fbc-0732285ed400, uuid:56afe972-4b8f-ef4b-a60b-7e69f6ebd1a0, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:D2C0AFCAB84EDF11B97582CA41FAF5D3, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:72C1005F55FCDE11B883974AB1AFE373, uuid:AA993898BD0CDF11A4CF8C80CD954A61, uuid:f6c75f86-b84d-a24c-a26d-fff2d07bb642, uuid:44c7f2c0-6d5e-754f-921e-a7e90c851dd4, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:b4762435-fa79-4d7e-beaa-246be0e558ea, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:b1c26a60-2079-5c4c-801a-9713ed358ab8, uuid:A63EAA4DBE0CDF11A4CF8C80CD954A61, uuid:e49a5566-b578-5846-b2c9-f12424097b13, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:f90c0d43-d052-e942-9688-277675624c55, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:F5261F0493CBDE11AB8AD4AAF7206634, uuid:869370c9-46d4-1347-b654-cd7c8ff1323d, uuid:02C334C653FCDE11B883974AB1AFE373, uuid:C61F5D9154FCDE11B883974AB1AFE373, uuid:81999ec2-77f3-e74f-b669-28dc0f20707b, uuid:0A8086FC75CBDE11AB8AD4AAF7206634, uuid:8D05507ABA0CDF11A4CF8C80CD954A61, uuid:24149677-d473-a644-aefb-afd454189545, uuid:06c1ed60-558a-a145-b06e-2ad0ebe67ead, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:270D8CF25CFCDE11B883974AB1AFE373, uuid:0E0EB8E257FCDE11B883974AB1AFE373, uuid:FA320D2CBB0CDF11A4CF8C80CD954A61, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:f4185659-315b-ff40-845d-5d6ef7111e10, uuid:f2b05e84-7721-6f46-b0d5-7b475cfa4367, uuid:f9bb0372-bc48-6044-bea7-e366f3c87fc7, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:BF95A27F2400DF11875CB5A8ADC50E77, uuid:143DE7166E9FDE11B008AFF10BB50A68, uuid:F5261F0493CBDE11AB8AD4AAF7206634, uuid:869370c9-46d4-1347-b654-cd7c8ff1323d, uuid:C61F5D9154FCDE11B883974AB1AFE373, uuid:90d512e8-1ef8-614f-8338-47118798793a, uuid:0A8086FC75CBDE11AB8AD4AAF7206634, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:b0507d0c-5712-174d-8495-590be1a19b54, uuid:0A8086FC75CBDE11AB8AD4AAF7206634, uuid:24149677-d473-a644-aefb-afd454189545, uuid:06c1ed60-558a-a145-b06e-2ad0ebe67ead, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:99f315e8-5145-e64e-a9f3-dd200788eea1, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:ddfefda7-eb89-4051-bc05-457480676e30, uuid:6298d6d3-df04-ba46-bc81-7af641603072, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:72C1005F55FCDE11B883974AB1AFE373, uuid:7ff7f977-6a54-4f45-8fa6-ef59614aeaa3, uuid:f22aa3fd-a461-2d45-81fc-799fe971aaad, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:87C28433BED9DE11A09B9B656AB2CFC9, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:bdfd12e4-727b-ec4c-9d93-a24e453ac89e, uuid:2a5c1099-6589-d94c-a483-072320f895f7, uuid:e076216e-74f6-e64d-9764-9f88b6859039, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:c746a719-e9e6-f441-89f1-c0a69ea5b568, uuid:52f7a313-db7e-0149-b8f4-7d4459ba0e03, uuid:b098d57a-59ce-3541-9c67-2b1e2c32cbe9, uuid:52C409ABAC44DF11A3B29F9FB102F89E, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:A9BB900A2237DF11B5B7E34799AF1F20, uuid:98FD115F2237DF11B5B7E34799AF1F20, uuid:64669306-510c-094d-a373-62bc3b52dbcd, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:5AC409ABAC44DF11A3B29F9FB102F89E, uuid:c15046ac-acd8-704f-aa62-35592c031506, uuid:cbc66c31-38c9-e848-9d43-3cc67ab19e69, uuid:0f25c9ae-d04a-7d4e-a557-c48d940eb3fd, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:f76303f9-6f74-0844-9862-f9a4a6cb4fc4, uuid:709D04652D00DF11875CB5A8ADC50E77, uuid:8F3C32692E00DF11875CB5A8ADC50E77, uuid:C637BA8024B0DE11B586E079E356F229, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3AC314442E00DF11875CB5A8ADC50E77, uuid:b771951a-d663-4f42-99e7-154de80c15b6, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:215F6182CE3CDF11A280D26352E5558E, uuid:f4936f3f-ab19-6e4e-b6ea-35854eec9849, uuid:bdfd12e4-727b-ec4c-9d93-a24e453ac89e, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4CC4A514E18BDD11A86DEEC692AB59E0, uuid:50562051E18BDD11A86DEEC692AB59E0, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:66437B07D993DE118CF8BA43C4ACE821, uuid:d7948155-1d63-cd42-aa18-61904a54999d, uuid:4f264490-35e4-7c4e-ad7f-e17e01f2c2d9, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:32f9f3e6-952c-f84c-a120-c7cd8e80f5ab, uuid:e3605c26-bb5f-cc40-87df-08016c9b823c, uuid:50713F46B7FDDE11945D8311A68CE99B, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:C548682E2DB0DE11B586E079E356F229, uuid:87A4461CD1B8DE1189F0985ED30C9E9D, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:87A4461CD1B8DE1189F0985ED30C9E9D, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:45B28A96EEFCDE11BFABCBBBBD1C47DC, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:DA6CF36F572FDE118BD7FAAED2B20C2F, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:DBFD6587B3C3DE11AC59D8DA84165BB4, uuid:4e8979c4-31cd-834a-9357-5751cfbaff25, uuid:D19FAE01B3C3DE11AC59D8DA84165BB4, uuid:98A802CEB5C3DE11AC59D8DA84165BB4, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:A8D5D166FD92DE11B60AD59153EA7D24, uuid:63E663F1BBC3DE11AC59D8DA84165BB4, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:2e990dd9-15a7-0046-a2d1-6afae165b340, uuid:9ce43ce9-b387-254b-9bd3-918f827e94c3, uuid:a912a88f-925e-674b-9ea0-2092632ebce7, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0A26F696CD9EDE11AF4ADCEACF161D1E, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:3a025c30-138f-9b4b-a113-1366a007dee1, uuid:D4AB4A583100DF11875CB5A8ADC50E77, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0496D6D167C5DE11900F98FD5AEC747D, uuid:ae5843a5-60b5-bb44-822c-bb2a29d41343, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0A8086FC75CBDE11AB8AD4AAF7206634, uuid:e076216e-74f6-e64d-9764-9f88b6859039, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:7F228B3854FCDE11B883974AB1AFE373, uuid:869370c9-46d4-1347-b654-cd7c8ff1323d, uuid:0496D6D167C5DE11900F98FD5AEC747D, uuid:AA6AE580BA0CDF11A4CF8C80CD954A61, uuid:5FC563C094CBDE11AB8AD4AAF7206634, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:840b9990-c574-0045-9b65-1602b2a48dad, uuid:9470C91A75CBDE11AB8AD4AAF7206634, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:2344d8a8-1fd4-1b43-ab58-03076cb1de64, uuid:D6C401FA86CBDE11AB8AD4AAF7206634, uuid:73cecda4-bbd5-1d49-b01d-68401a0ae257, uuid:C2ADFF59DF93DE118CF8BA43C4ACE821, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:A1C8628979D7DE1184D09483675CFE1B, uuid:588FA5E379D7DE1184D09483675CFE1B, uuid:ac9eb8bd-0b72-3b46-9f27-b929593386f2, uuid:06c1ed60-558a-a145-b06e-2ad0ebe67ead, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4c51d686-a5db-b340-a2aa-1727f1ac0767, uuid:F136084FC31BDF11B702E8F140A957AC, uuid:4c366215-27dc-3843-89ad-48491d7e5e42, uuid:F136084FC31BDF11B702E8F140A957AC, uuid:1b434750-ae32-2f48-ace2-6530f5a6258b, uuid:F136084FC31BDF11B702E8F140A957AC, uuid:222cc08e-bc61-7749-85f3-347d5468842d, uuid:F136084FC31BDF11B702E8F140A957AC, uuid:54b869a5-d6f0-4c42-a5b6-78315ac57745, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:d12b50a9-89f3-1f46-877b-47d685e31dee, uuid:5BC8915ABCC3DE11AC59D8DA84165BB4, uuid:F136084FC31BDF11B702E8F140A957AC, uuid:12da3c67-e6d1-7f4c-b94d-8035a031e0ca, uuid:F136084FC31BDF11B702E8F140A957AC, uuid:ddaf24b9-8969-fa44-b526-d54657c47113, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:02ffd0e6-8d4b-164a-9cd4-c76e2c812283, uuid:e076216e-74f6-e64d-9764-9f88b6859039, uuid:58b950fd-33e7-4ab4-a0fd-7f00549b364a, uuid:2a5c1099-6589-d94c-a483-072320f895f7, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:A6DB4025EA22DF11B39BC211848CC860, uuid:9EDB4025EA22DF11B39BC211848CC860, uuid:7727834EF622DF11B39BC211848CC860, uuid:ee68128a-709e-c64b-90eb-76874a580b70, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:96D237BCE922DF11B39BC211848CC860, uuid:622CECB6EE22DF11B39BC211848CC860, uuid:7F27834EF622DF11B39BC211848CC860, uuid:036bf5e8-28f6-f44f-9578-5bef85fbb1b2, uuid:CF630EB4EC22DF11B39BC211848CC860, uuid:007ADE247623DF11A0E6861CD2196B29, uuid:F10B07EAEC22DF11B39BC211848CC860, uuid:C2AD5AA07723DF11A0E6861CD2196B29, uuid:1FB840BE7723DF11A0E6861CD2196B29, uuid:4D2738C4ED22DF11B39BC211848CC860, uuid:CBAD5AA07723DF11A0E6861CD2196B29, uuid:39A3E0EE7723DF11A0E6861CD2196B29, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0499b5dc-216a-834f-b8d8-cf01515ef44e, uuid:91ed467b-bf37-e64b-93f0-7dfe327b006a, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:04316435-2b78-ba4a-ab66-b42d1da9a1d6, uuid:ec783e37-3479-f147-a917-a0e03e3ba787, uuid:eb32cf3d-f1ae-dc49-8221-c74b0ecd2e36, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:092799be-9bf2-0a45-8aa2-67d37dd19f6c, uuid:02C334C653FCDE11B883974AB1AFE373, uuid:f2b05e84-7721-6f46-b0d5-7b475cfa4367, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:A6C145BFA91CDF119776BC87C2148A4E, uuid:f19d28e7-51f4-5149-bd8b-b7e2be48717f, uuid:1caad7b5-51b0-424d-8ace-cafe18ade776, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:9CC4B0946B1CDF119776BC87C2148A4E, uuid:8539D47DBA0CDF11A4CF8C80CD954A61, uuid:29ffe1bb-14eb-124a-9c51-612aa059fa9f, uuid:0496D6D167C5DE11900F98FD5AEC747D, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3139d322-437a-2b46-9262-c11d45819282, uuid:B3A7725A2921DF11B8B990052AE8211F, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:BCA89B87BA0CDF11A4CF8C80CD954A61, uuid:bbfa492e-97b9-b040-a074-df3f175fb339, uuid:e3b4de3b-ed0d-c04b-9800-ac405b271c6a, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:9CC4B0946B1CDF119776BC87C2148A4E, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:e076216e-74f6-e64d-9764-9f88b6859039, uuid:58b950fd-33e7-4ab4-a0fd-7f00549b364a, uuid:35837e3d-0808-6b44-b847-46bff9c77441, uuid:1E992BA04721DF11B8B990052AE8211F, uuid:AF5085DD4721DF11B8B990052AE8211F, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:35837e3d-0808-6b44-b847-46bff9c77441, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:764fd520-99c3-8e4b-9059-8d3d66d30eb7, uuid:4dc420eb-ed4d-b447-a58b-04d06ea49d3b, uuid:0469cfd9-34af-a34f-9ac9-88273115bdf6, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:3d23163b-6e7e-0a41-9e31-f05d1717802c, uuid:4e479507-a3a2-9b4b-9d27-d5547f1cd4cd, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:2364707e-7cae-2d43-bf38-874610d0d64c, uuid:bdfd12e4-727b-ec4c-9d93-a24e453ac89e, uuid:c9a7f780-3260-7148-9e17-2a89ee4101c9, uuid:815e3a0f-8d4f-b945-ba26-7093cbfda35c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:39a7ea54-26c7-0b49-8d09-a39630851db6, uuid:0cd3d4d1-00c6-4045-845d-21dc3cfc11dc, uuid:8da32093-fda5-354c-9b3e-3c538315f711, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:520f86ed-75a2-d84e-8459-9e766579f279, uuid:db860d73-7269-2343-8d17-0c390d319ae0, uuid:ae3e71af-cc10-5942-afe5-8bf4681f7fcc, uuid:145300ee-8fb7-c14e-8341-9b2bc9da1000, uuid:FA320D2CBB0CDF11A4CF8C80CD954A61, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:131ef021-86a5-fc4e-9787-9720bc0f7cf6, uuid:131ef021-86a5-fc4e-9787-9720bc0f7cf6, uuid:f9330c08-8cff-2a42-8a2b-c61ec7eeed58, uuid:7d638375-48d0-174b-8649-84a6cb468d79, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:fe8d5792-19b3-1345-bf0b-21a26ebd73ec, uuid:319b6e0c-be4d-5541-b469-aecb4ac321aa, uuid:08f5b276-a201-8d4f-8974-09559c30cd09, uuid:8da32093-fda5-354c-9b3e-3c538315f711, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:e3fc7e3a-60a5-e149-bacb-887a1df11105, uuid:4dca9490-da34-eb4e-ba79-336ca49af570, uuid:2174c2c1-e344-9348-9d1b-797e928def65, uuid:c11dcbee-53a4-b144-aceb-5e8643d94c60, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:c6ed2fcc-8779-e144-b99c-e7d4813faeb8, uuid:1E992BA04721DF11B8B990052AE8211F, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:4b8fafb0-380b-9644-bfe5-c576d1bf597c, uuid:6cda7167-aaa3-7847-b9b2-ec6a03bc0410
Manifest Reference Document ID  : uuid:DA15B89E9FA811DEBC85916701D3F2E5, adobe:docid:indd:869c154d-9476-11de-a1e2-95a24d0eafab, adobe:docid:indd:869c1549-9476-11de-a1e2-95a24d0eafab, adobe:docid:indd:8257bab7-0288-11df-bea8-d63cd33d7b86, adobe:docid:indd:6f7751d1-9471-11de-a1e2-95a24d0eafab, uuid:C5EDC7BEB218DF119F94E5AD49C5B753, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:D6B61CCD2D9ADE11BBB9922C27375948, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:indd:6cee994c-0339-11df-a00c-834d31ce01ca, adobe:docid:indd:6cee9950-0339-11df-a00c-834d31ce01ca, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:indd:6dcce207-033c-11df-a00c-834d31ce01ca, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:indd:6dcce20e-033c-11df-a00c-834d31ce01ca, uuid:50425D857F61DE11B162A01704680C4D, uuid:B3F415AC5D07DF11BD08FFB407756A2B, uuid:945EE8FBD2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:indd:54ad094c-29cf-11df-9a69-839a8b44f15d, uuid:50425D857F61DE11B162A01704680C4D, uuid:0A240E66E3EBDE118803A68FDD55E0DE, adobe:docid:indd:5cc4dd30-9485-11de-b8fc-d077d75277e9, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:A773E22D1E7DDE11A432E4807C721F77, uuid:A6E6FF1FD3D9DE11A09B9B656AB2CFC9, uuid:9D22FDF33BEDDE11A89CA2F26CDD0695, adobe:docid:photoshop:d8e34893-8991-11de-ae8d-b2984c9ab724, uuid:E7D9E29B4524DF11A1D1CA7A6914DD75, uuid:8813103A6506DF11B37CB9EF37D61297, uuid:50425D857F61DE11B162A01704680C4D, uuid:A272CCB954EDDE11A89CA2F26CDD0695, uuid:93FC6FC94BFCDE118E22A5F05C1EE03B, uuid:56425D857F61DE11B162A01704680C4D, uuid:D1C0AFCAB84EDF11B97582CA41FAF5D3, uuid:50425D857F61DE11B162A01704680C4D, uuid:B740C5F954FCDE11B883974AB1AFE373, uuid:98879849BD0CDF11A4CF8C80CD954A61, uuid:02F17017403ADF11A676EA5B605A592C, adobe:docid:indd:b78740ab-9488-11de-b8fc-d077d75277e9, uuid:56425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:F17B856372AB11DEB7FD952816E135ED, uuid:56425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:C9C521EC9F61DE11B162A01704680C4D, uuid:A53EAA4DBE0CDF11A4CF8C80CD954A61, uuid:8ABF69C86107DF1194E9F0C38878D1B0, uuid:50425D857F61DE11B162A01704680C4D, uuid:1187C3B33C2CDF11AFE8FC03D5B9696F, uuid:50425D857F61DE11B162A01704680C4D, uuid:F4261F0493CBDE11AB8AD4AAF7206634, uuid:CB38BE187207DF1194E9F0C38878D1B0, uuid:C43A77F552FCDE11B883974AB1AFE373, uuid:C51F5D9154FCDE11B883974AB1AFE373, uuid:9951B1927007DF1194E9F0C38878D1B0, uuid:5B93B28075CBDE11AB8AD4AAF7206634, adobe:docid:photoshop:d8e34893-8991-11de-ae8d-b2984c9ab724, uuid:E7D9E29B4524DF11A1D1CA7A6914DD75, uuid:8813103A6506DF11B37CB9EF37D61297, uuid:50425D857F61DE11B162A01704680C4D, uuid:260D8CF25CFCDE11B883974AB1AFE373, uuid:0D0EB8E257FCDE11B883974AB1AFE373, uuid:F9320D2CBB0CDF11A4CF8C80CD954A61, uuid:56425D857F61DE11B162A01704680C4D, uuid:F5AE7176CAD9DE11A09B9B656AB2CFC9, uuid:D373EDFFD2D9DE11A09B9B656AB2CFC9, uuid:29FCC081CAD9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, uuid:BE95A27F2400DF11875CB5A8ADC50E77, uuid:B5FF3CDBED92DE11B60AD59153EA7D24, uuid:F4261F0493CBDE11AB8AD4AAF7206634, uuid:CB38BE187207DF1194E9F0C38878D1B0, uuid:C51F5D9154FCDE11B883974AB1AFE373, uuid:C938BE187207DF1194E9F0C38878D1B0, uuid:5B93B28075CBDE11AB8AD4AAF7206634, uuid:50425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, uuid:E193D779CAD9DE11A09B9B656AB2CFC9, uuid:5B93B28075CBDE11AB8AD4AAF7206634, uuid:E7D9E29B4524DF11A1D1CA7A6914DD75, uuid:8813103A6506DF11B37CB9EF37D61297, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:19D242D072BA11DEB7FD952816E135ED, uuid:4E425D857F61DE11B162A01704680C4D, uuid:4B8ED59C72B411DEB7FD952816E135ED, adobe:docid:indd:dc30e0b8-4483-11df-82ae-80eb203f61c5, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:B740C5F954FCDE11B883974AB1AFE373, uuid:97781E7DCAD9DE11A09B9B656AB2CFC9, uuid:C74571FED2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:86C28433BED9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:A6E6FF1FD3D9DE11A09B9B656AB2CFC9, uuid:48B2716ECAD9DE11A09B9B656AB2CFC9, uuid:4E425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:0C9DEE38BAD9DE11B9A5A33BDD060047, uuid:61AA2887D2D9DE11A09B9B656AB2CFC9, uuid:0E9DEE38BAD9DE11B9A5A33BDD060047, uuid:51C409ABAC44DF11A3B29F9FB102F89E, uuid:50425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, adobe:docid:photoshop:0ba7c7aa-97c7-11de-b2c1-cb7965a4638c, uuid:42F0E7B6D793DE118CF8BA43C4ACE821, uuid:A3E781E70AA5DE118E10FDC226834410, uuid:50425D857F61DE11B162A01704680C4D, uuid:59C409ABAC44DF11A3B29F9FB102F89E, uuid:91115F1D0608DF118E7882D1204A32A6, uuid:C6159F090B08DF118E7882D1204A32A6, uuid:E79563F8D2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:256986891208DF118E7882D1204A32A6, uuid:E920C4681FB0DE11B586E079E356F229, uuid:5DF11C3E20B0DE11B586E079E356F229, uuid:C537BA8024B0DE11B586E079E356F229, uuid:50425D857F61DE11B162A01704680C4D, uuid:CD37BA8024B0DE11B586E079E356F229, uuid:276986891208DF118E7882D1204A32A6, uuid:50425D857F61DE11B162A01704680C4D, uuid:205F6182CE3CDF11A280D26352E5558E, uuid:AC3AFDA7A73CDF1182E6A1C4668A8464, uuid:A6E6FF1FD3D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:4BC4A514E18BDD11A86DEEC692AB59E0, uuid:4F562051E18BDD11A86DEEC692AB59E0, uuid:50425D857F61DE11B162A01704680C4D, uuid:65437B07D993DE118CF8BA43C4ACE821, uuid:18EFE3A6F0FCDE11A9B2B0B61D2C07DC, uuid:b4ee7719-f86d-0246-9566-201759cf5447, uuid:50425D857F61DE11B162A01704680C4D, uuid:C005BB28F6FCDE11A9B2B0B61D2C07DC, uuid:C405BB28F6FCDE11A9B2B0B61D2C07DC, uuid:30017A10B6FDDE11945D8311A68CE99B, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:C448682E2DB0DE11B586E079E356F229, uuid:86A4461CD1B8DE1189F0985ED30C9E9D, uuid:50425D857F61DE11B162A01704680C4D, uuid:86A4461CD1B8DE1189F0985ED30C9E9D, uuid:56425D857F61DE11B162A01704680C4D, uuid:F1705C73EEFCDE11BFABCBBBBD1C47DC, uuid:50425D857F61DE11B162A01704680C4D, uuid:D96CF36F572FDE118BD7FAAED2B20C2F, uuid:50425D857F61DE11B162A01704680C4D, uuid:4761664AD993DE118CF8BA43C4ACE821, uuid:6BB04C592C8FDE1186EBCCA924499B2D, uuid:6180F137D993DE118CF8BA43C4ACE821, uuid:5061664AD993DE118CF8BA43C4ACE821, uuid:50425D857F61DE11B162A01704680C4D, uuid:A7D5D166FD92DE11B60AD59153EA7D24, uuid:D46249DBBAC3DE11AC59D8DA84165BB4, uuid:4E425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:9B361517D005DF1195FEB9F49690BC7E, uuid:3986A7A2D305DF1195FEB9F49690BC7E, uuid:3586A7A2D305DF1195FEB9F49690BC7E, uuid:50425D857F61DE11B162A01704680C4D, uuid:D021A27EED9DDE119E89E62532DB28E6, uuid:56425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, uuid:4518E851FDC5DE11AEDEFEDECD0EE79F, uuid:50425D857F61DE11B162A01704680C4D, uuid:FE95D6D167C5DE11900F98FD5AEC747D, uuid:FA9CC7E3DE38DF11A9C0A2AFB489E7CF, uuid:50425D857F61DE11B162A01704680C4D, uuid:5B93B28075CBDE11AB8AD4AAF7206634, uuid:4E425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:09C334C653FCDE11B883974AB1AFE373, uuid:CB38BE187207DF1194E9F0C38878D1B0, uuid:FE95D6D167C5DE11900F98FD5AEC747D, adobe:docid:photoshop:8eeae858-94ae-11de-861a-97001ccbaea0, uuid:5EC563C094CBDE11AB8AD4AAF7206634, uuid:56425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:DC1C165F9202DF11AB00FF362E9DBC86, uuid:9370C91A75CBDE11AB8AD4AAF7206634, uuid:50425D857F61DE11B162A01704680C4D, uuid:1708D6AD9902DF11AB00FF362E9DBC86, uuid:D5C401FA86CBDE11AB8AD4AAF7206634, uuid:1A08D6AD9902DF11AB00FF362E9DBC86, uuid:C1ADFF59DF93DE118CF8BA43C4ACE821, uuid:50425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, uuid:0056E7BF75D7DE1184D09483675CFE1B, uuid:5DC5863E79D7DE1184D09483675CFE1B, uuid:E5D9E29B4524DF11A1D1CA7A6914DD75, uuid:8813103A6506DF11B37CB9EF37D61297, uuid:50425D857F61DE11B162A01704680C4D, uuid:642C1D679C02DF11AB00FF362E9DBC86, uuid:7B88A6F89FD9DE11A09B9B656AB2CFC9, uuid:A626E8815224DF11A1D1CA7A6914DD75, uuid:7B88A6F89FD9DE11A09B9B656AB2CFC9, uuid:A826E8815224DF11A1D1CA7A6914DD75, uuid:7B88A6F89FD9DE11A09B9B656AB2CFC9, uuid:AA26E8815224DF11A1D1CA7A6914DD75, uuid:7B88A6F89FD9DE11A09B9B656AB2CFC9, uuid:AD26E8815224DF11A1D1CA7A6914DD75, uuid:50425D857F61DE11B162A01704680C4D, uuid:54425D857F61DE11B162A01704680C4D, uuid:5AC8915ABCC3DE11AC59D8DA84165BB4, uuid:7B88A6F89FD9DE11A09B9B656AB2CFC9, uuid:81DEF5885424DF11A1D1CA7A6914DD75, uuid:7B88A6F89FD9DE11A09B9B656AB2CFC9, uuid:84DEF5885424DF11A1D1CA7A6914DD75, uuid:50425D857F61DE11B162A01704680C4D, uuid:1DC9ABCA7DB9DE118B79FC1517C31705, uuid:4E425D857F61DE11B162A01704680C4D, uuid:046546A01C7211DF94B9A6174B471A3D, uuid:48B2716ECAD9DE11A09B9B656AB2CFC9, uuid:56425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:255714ECE922DF11B39BC211848CC860, uuid:2E5714ECE922DF11B39BC211848CC860, uuid:3DDA4C27F622DF11B39BC211848CC860, uuid:2BF02217F222DF1199EAF2B78B762DC7, uuid:50425D857F61DE11B162A01704680C4D, uuid:95D237BCE922DF11B39BC211848CC860, uuid:A3E9FC9DEE22DF11B39BC211848CC860, uuid:E7F8715FEB22DF11B39BC211848CC860, uuid:27F02217F222DF1199EAF2B78B762DC7, uuid:CE630EB4EC22DF11B39BC211848CC860, uuid:FF79DE247623DF11A0E6861CD2196B29, uuid:F00B07EAEC22DF11B39BC211848CC860, uuid:3C85C4537723DF11A0E6861CD2196B29, uuid:1EB840BE7723DF11A0E6861CD2196B29, uuid:4C2738C4ED22DF11B39BC211848CC860, uuid:CAAD5AA07723DF11A0E6861CD2196B29, uuid:38A3E0EE7723DF11A0E6861CD2196B29, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:4B8ED59472B411DEB7FD952816E135ED, uuid:50425D857F61DE11B162A01704680C4D, uuid:7481D08BD038DF11A9C0A2AFB489E7CF, uuid:7681D08BD038DF11A9C0A2AFB489E7CF, uuid:82849C9E9D5DDE11B41782D1E07552D1, uuid:50425D857F61DE11B162A01704680C4D, uuid:11F66F20D3D9DE11A09B9B656AB2CFC9, uuid:C43A77F552FCDE11B883974AB1AFE373, uuid:D373EDFFD2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:photoshop:8c721c40-8cca-11de-a6a4-9e42f2c9bca9, uuid:DF1F7304D3D9DE11A09B9B656AB2CFC9, uuid:7C431D04D3D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:9BC4B0946B1CDF119776BC87C2148A4E, adobe:docid:photoshop:b37012f3-8a57-11de-a556-d44ccda0d8c1, uuid:EF85F88ACAD9DE11A09B9B656AB2CFC9, uuid:FE95D6D167C5DE11900F98FD5AEC747D, uuid:50425D857F61DE11B162A01704680C4D, uuid:3E143CEED2D9DE11A09B9B656AB2CFC9, uuid:B2A7725A2921DF11B8B990052AE8211F, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:photoshop:8f813604-8cdb-11de-a6a4-9e42f2c9bca9, uuid:38960F8ACAD9DE11A09B9B656AB2CFC9, uuid:A91D5EF7D2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:9BC4B0946B1CDF119776BC87C2148A4E, uuid:50425D857F61DE11B162A01704680C4D, uuid:4E425D857F61DE11B162A01704680C4D, uuid:046546A01C7211DF94B9A6174B471A3D, uuid:D8296EF5D2D9DE11A09B9B656AB2CFC9, uuid:D6B61CCD2D9ADE11BBB9922C27375948, uuid:A95085DD4721DF11B8B990052AE8211F, uuid:50425D857F61DE11B162A01704680C4D, uuid:56425D857F61DE11B162A01704680C4D, uuid:D8296EF5D2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:0F8F02F6D2D9DE11A09B9B656AB2CFC9, uuid:01A8A5F4D2D9DE11A09B9B656AB2CFC9, uuid:56425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:7089D2F6D2D9DE11A09B9B656AB2CFC9, uuid:FF66CAFDD2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:8A5EE8FBD2D9DE11A09B9B656AB2CFC9, uuid:A6E6FF1FD3D9DE11A09B9B656AB2CFC9, uuid:DEDADF8BCAD9DE11A09B9B656AB2CFC9, uuid:41B2B1ECD2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:BC6098F3D2D9DE11A09B9B656AB2CFC9, uuid:E9A0D2F2D2D9DE11A09B9B656AB2CFC9, uuid:5EC837F2D2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:22AB3F8ECAD9DE11A09B9B656AB2CFC9, uuid:265A790AD3D9DE11A09B9B656AB2CFC9, uuid:7BBDE58CCAD9DE11A09B9B656AB2CFC9, uuid:1FFD16309E1BDF118FD6E436D4DAB382, uuid:F9320D2CBB0CDF11A4CF8C80CD954A61, uuid:50425D857F61DE11B162A01704680C4D, uuid:5969168FCAD9DE11A09B9B656AB2CFC9, uuid:5969168FCAD9DE11A09B9B656AB2CFC9, uuid:B7935840FA9DDE119F1EB73076F57870, uuid:782DCB96CAD9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:F8059A85B7FDDE118ADC9A0539C38197, uuid:2A0E3306D3D9DE11A09B9B656AB2CFC9, uuid:E327C105D3D9DE11A09B9B656AB2CFC9, uuid:5EC837F2D2D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:2EF00C08D3D9DE11A09B9B656AB2CFC9, uuid:1C5A790AD3D9DE11A09B9B656AB2CFC9, uuid:C983F508D3D9DE11A09B9B656AB2CFC9, uuid:EF55CA06D3D9DE11A09B9B656AB2CFC9, uuid:50425D857F61DE11B162A01704680C4D, uuid:4082E4FAD2D9DE11A09B9B656AB2CFC9, uuid:D6B61CCD2D9ADE11BBB9922C27375948, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, uuid:50425D857F61DE11B162A01704680C4D, adobe:docid:indd:c367ca33-9489-11de-b8fc-d077d75277e9
Format                          : application/pdf
Title                           : sb1012_m1.pdf
Creator                         : 
Producer                        : Acrobat Distiller 8.1.0 (Macintosh)
Trapped                         : False
Page Count                      : 148
Author                          :

EXIF Metadata provided by EXIF.tools

Southbend Sb1015f Sb1012_m1 User Manual To The 958c5c0f 05a7 4965 97e6 38e48b6d1645

Navigation menu

Versions of this User Manual:

Views

Navigation