SparkLAN Communications AD600Z Wireless 11g Detachable Antenna USB Adapter User Manual QIG
SparkLAN Communications, Inc. Wireless 11g Detachable Antenna USB Adapter QIG
Manual
IEEE 802.11b/g
Wireless Detachable Antenna
USB Adapter
QUICK GUIDE
VERSION 1.0
BOX CONTENTS
Wireless LAN Adapter Driver CD Quick Start Guide
INSTALL DRIVER / UTILITY
The installation & driver CD will automatically activate the autorun
installation program after you insert the disk into your CD drive.
Step 1 :
Insert the installation & driver CD
into your CD-ROM.
Step 2 :
Click Next to continue.
1
Step 3 :
Click Next to install at the desig-
nated folder. Or, click “Browse”
to select different folder.
Step 4 :
Start copying files until it finish
the installation.
Step 5 :
Click Finish to complete
installation.
Step 6 :
After finished install driver and
utility on your system, plug the
USB adapter into the USB port of
your PC. Windows XP/2000 will
automatically detect the USB
Adapter.
2
WIRELESS NETWORK CONFIGURATION
WLAN USB Adapter uses its own management software. All functions
controlled by users are provided by this application. When you insert the
WLAN USB Adapter into the USB port of PC, a new icon should appear in
the Windows System Tray automatically.
If the icon is in red, it means that WLAN USB Adapter configuration is
invalid or incomplete. Double click on that icon and the configuration
window will pop up as shown below. It shows the SSID of available
network. Once a network is chosen, the signal strength and link quality
are displayed.
The Link Quality and Signal Strength
bar chart is only active when the
node is in Infrastructure Mode. The
bar graph displays the quality and
strength of the link between the
node and its Access Point. Link
Quality is a measurement of receiv-
ing and transmitting performances
over the radio.
Tx/Rx Frame displays the instanta-
neous wireless Transmit and Receive
throughput in bytes per second. These values are updated every two
seconds.
The Configuration Tool contains several fields where operating param-
eters of the driver can be viewed or changed. Changes to any of the
parameters in this panel can be applied to the driver without a need to
restart the computer.
3
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
The availability of some specific channels and/or operational
frequency bands are country dependent and are firmware
programmed at the factory to match the intended destination. The
firmware setting is not accessible by the end user.
European Union Notice:
Radio products with the CE marking comply with the R&TTE Directive
(1999/5/EC), the EMC Directive (89/336/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following
European Norms:
◆ EN 60950 Product Safety
◆ EN 300 328 Technical requirement for radio equipment
◆ EN 301 489-1/-17 General EMC requirements for radio equipment
The equipment has been tested and found to comply with FCC and CE
Rules.Operation is subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received including
interference that may cause undesired operation.
The AD-600Z (FCC ID: RYK-AD600Z) is limited in CH1~CH11 for 2.4 GHz
by specified firmware controlled in U.S.A.