SparkLAN Communications WPEA352ACNRB 802.11ac/b/g/n Mini PCIe Module User Manual Contents

Download:
Mirror Download [FCC.gov]
Document ID	4181985
Application ID	smX5vwaDYWB+5d0w9l9rrA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.6kB (145022 bits)
Date Submitted	2019-02-27 00:00:00
Date Available	2019-02-27 00:00:00
Creation Date	2019-02-19 15:58:48
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2019-02-19 15:59:03
Document Title	Contents
Document Creator	Acrobat PDFMaker 15 Word 版
Document Author:	user

WPEA-352ACNRB
WPEA-352ACNRBI
Manual
1.PRODUCT INTRODUCTION
Standard
IEEE802.11ac/a/b/g/n
Chipset solution
QCA9880-BR4A
Radio stream [Note1]
3T3R
Antenna type / connector.
External with IPEX connector
Bus Interface
PCI Express
Form Factor
Mini-PCIe
802.11b: 11, 5.5, 2, 1 Mbps;
802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11n:
MCS 0 to 15 for HT20MHz
MCS 0 to 15 for HT40MHz
Data Rate
802.11ac:
MCS 0 to 8 for HT20MHz
MCS 0 to 9 for HT40MHz
MCS 0 to 9 for HT80MHz
1. In HT (High Throughput) mode, the data rate depends on the MCS Index.
2. The MCS index for HT (High Throughput) mode is from 0 to 32 as described
in the MCS table.
802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
Spreading /Modulation
Techniques
802.11b: DSSS (DBPSK, DQPSK, CCK)
802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM)
802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM)
802.11ac: OFDM (BPSK,QPSK,16-QAM,64-QAM, 256-QAM)
Frequency Range
[Note2]
11b/g/n: 2.412GHz ~ 2.484GHz
11ac/a/n: 5.15GHz ~ 5.85GHz
802.11a: 14dBm@54Mbps
802.11b: 20dBm@11Mbps
802.11g: 16dBm@54Mbps
Transmit Output Power
(Tolerance: +/-2dBm)
802.11gn HT20: 15dBm@MCS7
802.11gn HT40: 15dBm@MCS7
802.11an HT20: 13dBm@MCS7
802.11an HT40: 13dBm@MCS7
802.11ac VHT80: 10dBm@MCS9
802.11a: ≤-73dBm@54Mbps
802.11b: ≤-86dBm@11Mbps
802.11g: ≤-73dBm@54Mbps
Receiver Sensitivity
802.11gn HT20: ≤-70dBm@MCS7
802.11gn HT40: ≤-67dBm@MCS7
802.11an HT20: ≤-71dBm@MCS7
802.11an HT40: ≤-68dBm@MCS7
802.11ac VHT80: ≤-58dBm@MCS9
Operating Voltage
DC 3.3V
Power Consumption
TX:1360mA (Max)
Temperature Range
-20°C~ +65°C (Operating) /-30°C~ +75°C (Storing)
Humidity (non-condensing)
10~85 % (Operating), 5~90 % (Storing) [Note3]
Security
OS supported
WEP / WPA / WPA2,802.1X
Linux (Linux supports have different versions based on different CPU platforms
and O/S. Please contact SPK support group.)
Note:
1. For Radio stream with diversity or MIMO design, all RF connectors on the module must
be fitting antennas in order to guarantee the module performance.
2. The frequency range is subject to local regulations.
3. The storing condition is only for product functionality, no included for parts appearance.
2. HARDWARE SPECIFICATION
2.1 Hardware Dimension
Dimension: 50.8mm * 29.85mm * 4.1mm(±0.5mm)
2.3 Pin Assignment
The following section illustrate signal pin-outs for the system connector.
Pin#
Pin Name
Description
Pin#
+3.3V
GND
GND
No Connection
No Connection
No Connection
No Connection
No Connection
WAKE_L(NA)
Output and open Drain
active Low signal. This
signal is used to request
that the system return
from a sleep/suspended
state to service a
function initiated wake
event.
No Connection
No Connection
CLKREQ_L
Output for reference
clock request signal
GND
GND
REFCLK-
Input signal for PCI
10
Express differential
11
Pin Name
Description
+3.3V
12
reference clock (100
MHz)
REFCLK+
Input signal for PCI
Express differential
13
14
reference clock (100
MHz)
15
GND
GND
16
No Connection
17
No Connection
18
GND
No Connection
W_DISABLE_L
GND
Input and active low
signal. This signal is
used by the system to
disable radio operation
19
on add-in cards that
20
implement radio
frequency applications.
When implemented, this
signal requires a pull-up
resistor on the card
21
GND
GND
22
PERST_L
Input signal for
functional reset to the
card
PERn0
23
PCI Express x1 data
interface: one differential
+3.3V
+3.3V
GND
GND
24
receive pair
PERp0
25
PCI Express x1 data
interface: one differential
26
receive pair
27
GND
GND
28
No Connection
29
GND
GND
30
No Connection
PETn0
PCI Express x1 data
No Connection
GND
GND
31
interface: one differential
32
transmit pair
PETp0
33
PCI Express x1 data
interface: one differential
34
transmit pair
35
GND
GND
36
No Connection
37
GND
GND
38
No Connection
39
No Connection
40
GND
GND
41
No Connection
42
No Connection
GND
GND
Output and open drain
active low signal. This
signal is used to allow
43
44
LED_WLAN_L
(OPT)
the PCI Express Mini
Card add-in card to
provide status indicators
via LED devices that will
be provided by the
system
45
No Connection
46
No Connection
47
No Connection
48
No Connection
49
No Connection
50
No Connection
51
No Connection
52
+3.3V
+3.3V
* NA: No active
* OPT: Optional (Depends on S/W and H/W design of the module and customer platform
main board, functionalities of end devices and drivers.)
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device is restricted to indoor use.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The module is limited to OEM installation ONLY.
This module is intended for OEM integrators under the following conditions:
1. This module is restricted to installation in products for use only in mobile and fixed applications.
2. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20
cm from all persons.
3. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or
transmitter.
4. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.
5. Fixed outdoor applications for point to multipoint operations are subject to the conditions in Part
15.407(a)(1)(i).
The OEM integrator is still responsible for
1. ensuring that the end-user has no manual instructions to remove or install module
2. the FCC compliance requirement of the end product, which integrates this module.
3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations
(e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer.
4. The separate approval is required for all other operating configurations, including portable configurations
with respect to Part 2.1093 and different antenna configurations
The user manual of the end product should include
1. Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
2. the restriction of operating this device in indoor could void the user’s authority to operate the equipment.
3. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna
or transmitter.
4. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
5. The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Label of the end product:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
RYK-WPEA352ACNRB".
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
If the labelling area is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the
compliance statement, then the statement may be placed in the user manual or product packaging.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This radio transmitter [IC: 6158A-WPEA352ACNB] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for
any type listed are strictly prohibited for use with this device.
FCC/ISED Antenna List
5GHz
Brand
Model
Connector Type
Type
2.4GHz
Band 1
Band 2
Band 3
Band 4
SparkLAN
AD-103AG
I-Pex
Dipole
2.03
SparkLAN
AD-301N
I-Pex
Dipole
SparkLAN
AD-302N
I-Pex
Dipole
2.87
3.14
SparkLAN
AD-303N
I-Pex
Dipole
3.45
3.14
SparkLAN
AD-305N
I-Pex
Dipole
5.53
SparkLAN
AD-300N
I-Pex
Dipole
5.2
2.02
5.8
4.4
Le présent émetteur radio [IC: 6158A-WPEA352ACNB] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant
un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.
FCC/ISED Antenna List
5GHz
Brand
Model
Connector Type
Type
2.4GHz
Band 1
Band 2
Band 3
Band 4
SparkLAN
AD-103AG
I-Pex
Dipole
2.03
SparkLAN
AD-301N
I-Pex
Dipole
SparkLAN
AD-302N
I-Pex
Dipole
2.87
3.14
SparkLAN
AD-303N
I-Pex
Dipole
3.45
3.14
SparkLAN
AD-305N
I-Pex
Dipole
5.53
SparkLAN
AD-300N
I-Pex
Dipole
5.2
2.02
5.8
4.4
the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems;
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin
de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
IC Radiation Exposure Statement:
10
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre
corps
Modular OEM Integrator Notice
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif
module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20cm est respectée entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
The OEM integrator is still responsible for
1.
ensuring that the end-user has no manual instructions to remove or install module
2.
the ISED compliance requirement of the end product, which integrates this module.
3.
Appropriate measurements and if applicable additional equipment authorizations of the host device to be addressed
by the integrator/manufacturer.
4.
The separate approval is required for all other operating configurations, including portable configurations and different
antenna configurations
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains transmitter module IC:
6158A-WPEA352ACNB”.
Contient le module d'émission IC: 6158A-WPEA352ACNB
The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging
or product literature which shall be available with the end product or online.
11
Japan Antenna List
Brand
Model
Connector
Type
5GHz
Type
2.4GHz
Band 1
Walsin
RFDPA131000SBLB808
I-Pex
Dipole
Cortec
AN2450-5511BRS
I-Pex
Dipole
SANSEI
ANTDP-027A0
I-Pex
Dipole
1.3
Taoglas
MA231.LBC.002
I-Pex
Flat Bar
WIESON
GPOT113-020A
I-Pex
Dipole
Cortec
AN2450-16HM01BRS
I-Pex
Dipole
7 ARISTOTLE RFA-25-AP252-70-500
I-Pex
PCB
8 ARISTOTLE RFA-25-AP287-4B-350F
I-Pex
PCB
3.5
LYNwave
ALX17P-221XX9-00
I-Pex
PCB
10
LYNwave
ALX17P-221XXG-00
I-Pex
PCB
RFA-25-C17M5-1
I-Pex
Dipole
11 ARISTOTLE
Band 2
Band 3
4.4
3.14
2.93
3.58
2.89
1.3
1.2
1.5
2.84
2.84
2.84
2.41
-5.96
-5.96
-5.96
-0.79
6.27
6.67
2.15
2.6
3.62
2.47
3.5
3.5
2.8
3.6
3.6
3.6
3.7
3.6
3.6
3.6
3.7
4.8
1.5
12
vso
GRF1351
I-Pex
Dipole
4.9
2.9
13
exceltek
C0255-ANG0027
I-Pex
PCB
14
exceltek
C0255-ANG0029
I-Pex
PCB
15
exceltek
C0255-ANG0018
I-Pex
Dipole
2.8
2.6
2.9
2.4
16
Anjie
EX06-2458-B1-SMA-MR
I-Pex
Dipole
17 ARISTOTLE
RFA-25-C2M2-U-M70
I-Pex
Dipole
18 ARISTOTLE
RFA-25-C2M2-M32-N
I-Pex
Dipole
1.81
2.56
2.03
2.02
1.9
2.34
2.34
1.5
2.34
2.9
19
SparkLAN
AD-103AG
I-Pex
Dipole
20
SparkLAN
AD-301N
I-Pex
Dipole
21
SparkLAN
AD-302N
I-Pex
Dipole
2.87
3.14
22
SparkLAN
AD-303N
I-Pex
Dipole
3.45
3.14
23
SparkLAN
AD-305N
I-Pex
Dipole
5.53
24
SparkLAN
AD-300N
I-Pex
Dipole
25
SparkLAN
AD-300PF
I-Pex
Pifa
12
5.2
5.8
4.4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : user
Company                         : Sporton
Create Date                     : 2019:02:19 15:58:48+08:00
Modify Date                     : 2019:02:19 15:59:03+08:00
Source Modified                 : D:20190218075640
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2019:02:19 15:59:03+08:00
Creator Tool                    : Acrobat PDFMaker 15 Word 版
Document ID                     : uuid:89e232bd-3347-43a8-94cb-80572d2b3967
Instance ID                     : uuid:9edacd32-2c21-4a31-901a-73fc06394db8
Format                          : application/pdf
Title                           : Contents
Description                     : 
Creator                         : user
Producer                        : Adobe PDF Library 15.0
Keywords                        : 
Page Layout                     : OneColumn
Page Count                      : 12

EXIF Metadata provided by EXIF.tools