Spin Master Toys Far East 70437 Two Way Radio with FRS User Manual T70437 4000 20061521 NEN IS R2 updated
Spin Master Toys Far East Ltd. Two Way Radio with FRS T70437 4000 20061521 NEN IS R2 updated
User Manual
Fig. 2
MENU
PTT/CALL
Antenna
Speaker
Headset port
Power/Down
button
PTT/CALL
button
LCD panel
Menu/Up
button
Microphone
Fig. 1
a.
c.
b.
Belt clip
LONG RANGE
WALKIE TALKIES
Important: Please save this instruction sheet.
It contains valuable product information.
LONG RANGE WALKIE TALKIES 70437-4000-G1 PS 5/11
Foreign patents pending. Product colors and specifications subject to change.
ATTENTION ADULTS—TO REPLACE BATTERIES
The Long Range Walkie Talkies requires three AAA batteries (LR03), not included.
1. Remove belt clip: (a.) pinch tab inside the top of the clip; (b.) slide clip up to release;
and (c.) slide battery cover down and off. (Fig. 1)
2. Use a small Phillips screwdriver to loosen the screw in the BATTERY COVER.
NOTE: Screws will not detach from battery compartment cover.
3. Remove the cover.
4. Place batteries in the compartment as shown. (Fig. 2)
5. Replace BATTERY COVER and tighten screws.
BATTERY SAFETY
• Only adults should install and replace batteries.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Non-rechargeable batteries are not to be recharged.
• Remove dead or exhausted batteries.
• Insert batteries correctly. Match positive and negative signs.
• The supply terminals are not to be short-circuited.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only the batteries of the same or equivalent type recommended to be used.
• Do not dispose batteries in a fire; they may explode.
• Dispose of batteries safely.
Warning! Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This unit has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This unit generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this unit does cause harmful interference to
radio or television reception, which can be determined by turning the unit off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the unit and receiver.
• Connect the unit into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Ages 6 and up
70437
Requires three AAA
batteries (LR03), not included.
Warning: Do not hold close to the ear.
Misuse may damage hearing.
Long range walkie talkie
Model: 74047
RF Power: 0.5W
Freq.: 462.5625-467.7125MHz
TM
TM & © Spin Master Ltd. All rights reserved.
SPIN MASTER LTD., 450 FRONT ST. WEST, TORONTO, ON M5V 1B6 CANADA
Spin Master Inc., PMB #10053, 300 International Drive,
Suite 100, Williamsville, NY 14221 customercare@spinmaster.com
1-800-622-8339 • www.spinmaster.com
MADE IN CHINA
T70437_4000_20061521_NEN_IS_R2
Body Worn configuration
For body worn operation, this unit has been tested and meets FCC RF exposure guidelines when
used with the supplied belt-clip. Use of other accessories may not ensure compliance with FCC
RF exposure guidelines.
Warning: Any adjustment to this equipment is recommended to be performed by or under the
immediate supervision and responsibility of a person certified as technically qualified to perform
transmitter maintenance and repair duties in the private land mobile services and fixed services
by an organization or committee representative of users of those services.
Warning: Replacement of any transmitter component (crystal, semiconductor, etc.) for this
equipment could result in violation of FCC rules.
SAFETY INFORMATION
Your wireless hand-held portable transceiver contains a low power transmitter. When the
Push-to-Talk (PTT) button is pushed it sends out radio frequency (RF) signals. The device is
authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal
Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for
hand-held wireless devices.
CAUTION: To maintain compliance with the FCC's RF exposure guidelines hold the transmitter
and antenna at least 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the
antenna pointed up and away from the face.
FUNCTION DESCRIPTION
Belt clip: The belt clip is attached for easy use.
LCD Panel: Displays current channel selection and other radio status symbols.
POWER/DOWN BUTTON: Press and hold the button to turn your
unit on/off. Press the button to decrease the speaker volume.
MENU/UP BUTTON: Press and hold the
MENU
button to Channel
and function selector. Press the
MENU
button to increase the
speaker volume.
PTT/CALL button: Press and hold PTT/CALL button to transmit.
Press PTT/CALL button twice to Call.
LCD PANEL ICON DESCRIPTIONS
Receiving icon, displayed when reviving a signal
Transmitting icon, displayed when transmitting a signal
Display of current volume
Displayed during the Channel Scan mode
Display of the current battery level
Channel number
OPERATION
Turning the unit ON
• Press and hold the button. The unit will beep and the LCD display will
display the current channel.
Turning the unit OFF
• Press and hold the button. The unit will beep and the LCD display will turn blank.
Adjusting speaker volume
• Press the
MENU
button to increase the speaker volume.
• Press the button to decrease the speaker volume.
• The speaker volume level is indicated by the number of bars displayed
in the lower left corner of the LCD display.
RECEIVING COMMUNICATION
• When the unit is switched on and not being used for speech or calling,
it is always in the receiving mode.
• Pressing the PTT/Call button automatically overrides and turns
off the receiving mode.
Calling another radio
• Turn the volume up to an audible level.
• Set both units to the same channel.
• Press PTT/CALL button twice to Call. The other unit will make
a 2 second call tone.
Changing channels
The COMMUNICATOR has multi-channels. To change channels:
1. Press and hold the
MENU
button until the current channel number
and (ch) icon flash on the LD display.
2. While the channel number is flashing:
• Press the
MENU
button to move to a higher channel.
• Press the button to move to a lower channel.
3. Press and hold the
MENU
button to choose the desired channel
and return to normal mode, or press the PTT/CALL button.
MONITOR
This feature helps in receiving signals at maximum range, but will pick up
loud static signals too.
• Press the on and
MENU
buttons at the same time to activate the MONITOR.
• Press the on or
MENU
buttons to change the speaker volume.
• Press the PTT/CALL button to restore to normal.
CHANNEL SCAN
• Your radio can scan across 14 channels allowing it to search for other radios
without changing channels. To scan:
• Press and hold the
MENU
button until the current channel number and (ch) icon
flash on the LCD display.
• Press the PTT/CALL button to select the SCAN feature.
• Press the
MENU
button to ON to activate the channel scan. The channel
number will run rapidly on the display. When a signal is detected, the channel
scan pauses keeping the active signal broadcasted. Press the button to
search for another active channel.
• To stop the scanning operation, press the PTT/CALL button again.
Low battery indicator
When the batteries need to be changed, the battery level icon will flash.
To ensure uninterrupted communication, replace the batteries as soon
as possible.
MENU
PTT/CALL