Spot AX550 Low Power Spread Spectrum Module User Manual 01 0137

Download:
Mirror Download [FCC.gov]
Document ID	154581
Application ID	jqkzEibt1YOeAAJP+EZ+rA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.53kB (631678 bits)
Date Submitted	2001-06-13 00:00:00
Date Available	2001-06-15 00:00:00
Creation Date	2001-05-22 08:33:38
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	01-0137.PDF
Document Creator	Microsoft Word
Document Author:	Workstation

FCC ID: L2VAX550
SECTION 10
USER'S MANUAL
FCC ID: L2VAX550
Axonn Corporation
AX550
Transceiver
Users Manual
The AXSSD Transceiver is E} membei of our Spread Spectrum RF famiiy of products. Tt‘is transceiver
should only be installed by qualified service personnel.
The transceiver detects level, low battery or other data signolstrom the external binary inputs and
broadcasts that data to the system‘s host receiver.
MOUNTING LOCATION
The AX550 Transceiver is O moduie as defined by the FCC and therefore must be mounted to
another host device in order to function.
NOTICE TO CUSTOMER
Any Axonn customer incorporating the AXSSO transceiver module into its own product must hove
an external notice affixed to its product. This notice rnust be placed in a conspicuous location
end can use wording such as. "Contains FCC ID: LZVAXSSD" or “Contains Transceiver Module FCC
lD, LZVAXSSO" Any similar wording that expresses the same meaning may be used.
INSTALLATION INSTRUCTIONS
l. Supply the transceiver with DC power by inserting two 3.6 Voit batteries into the battery holder
on the customers host application circuit board.
2. The unit will come preprogrommed with Transceiver D and Property Code However, the
customer does hove the option oi tietd programming the unit.
3. When installing the AXSSO you should avoid areas near screens, metol window lromes, circuit
breaker boxes, air conditioners and heaters it a suitable location tor the unit may be found
elsewhere.
CAUTION:
This device is required to comply with FCC RF exposure requirements for mobile transmitting
devices. A separation of 20 cm (8 inches] Or more must be maintained between the antenna and
all persons during deVice operations to satisfy RF exposure compliance.
TESTING THE TRANSCEIVER
Following system installation, syslem testing is mandatory This should oe performed by locating
the AXSSO in its iinai location and powering up the unit On initial power—up, the AXSSO WiII Send
out RF messages every 4 seconds or more depending on programming. This will estobtish
communications with the host receiverand the iniormction collected wiil then be used to judge
system performance.
FCC ID: L2VAX550
FCC NOTICE
The AXSSO transceiver generates and uses radio frequency energy. if not installed and usea‘ in
accordance with the manufacturer‘s instructions, it may cause interference to radio and teleVision
reception The transmitter has been tested and found to comply with the specifications in Part 95
of the FCC Rules.
it this equipment causes interference to radio or television reception — which can be determined
by turning the equipment on and off — the installer is encouraged to correct the interference by
one or more of the following measures: l) Reorient the antenna of the radio/television. 2]
Connect the AC transformer to a ditterent outlet so the TED and radio/television are on different
branch circuits. 3) Relocate the TED with respect to the radio/television.
it necessary, the installer should consult an experienced radio/television technician for
additional suggestions, or send for the “interference Handbook” prepared by the Federal
Communications Commission. This booklet is available from the U.S. Government Printing
Cities, Washington. D.C., 20402,510Cl< number GOA-0004704507.
CAUTlON: Axonn Corporation does not support field changes or modifications to any of
the Axonn Corporation RF equipment unless they are speciticaiiy covered in this manual.
All adjustments must be made at the factory under the specific guidelines set forth in our
manufacturing processes Any modification to the equipment could void the user‘s
authority to operate the equipment and render the equipment in violation of FCC Part
95.
This device complies with Part 95 of the FCC Rules, Operation is subject to the following
two conditions: (it this aeVice may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
lIMlTED WARRANTY
THERE ARE NOT WARRANTIES. EXPRESS OR IMPLlED, OF MERCHANTABIUTY OR FlTNESS FOR A
PARTlCULAR PURPOSE OR OTHERWlSE, WHICH EXTEND BEYOND THE DESCRlPTION ON THE FACE
HEREOF. in no case shall Seller be liable to anyone for any consequential or incidental
damages tor breach of this or any other warranty, express or implied, or upon any other basis
of liability whatsoever, even if the loss or damage 55 caused by Seller's own negligence or fault.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 3
Creator                         : Microsoft Word
Create Date                     : 2001:05:22 08:33:38
Title                           : 01-0137.PDF
Author                          : Workstation
Producer                        : Acrobat PDFWriter 4.0 for Windows

EXIF Metadata provided by EXIF.tools