Spyder Xtra 05 Users Manual Kingman New XTRA2

: Spyder Spyder-Xtra-05-Users-Manual-804643 spyder-xtra-05-users-manual-804643 spyder pdf

Open the PDF directly: View PDF .
Page Count: 1

SPYDER XTRA OPERATION GUIDE:

1. To put the marker on “SAFE”, push the safety from the “PUSH SAFE” side of the trigger frame.

To disengage the safety, point the marker in safe direction, push in the safety from

the “PUSH FIRE” side of the trigger frame.

2. Cock the marker by pulling the Cocking Bolt (#17H) rearward until it latches.

Caution: if you let go before it latches, your marker may fire.

3. Tighten the air tank until it is snug. If a leak occurs between the air tank and the C/A Adapter,

replace the tank o-ring.

4. Install a 7/8” elbow with loader into the vertical feed. Fill the loader with .68 caliber paintballs only.

5. With the safety off, fire the marker by pulling the trigger.

6. Only use lubrication specifically designed for paintball markers. To lubricate your marker, you will

need to disassemble your marker (please note how parts are removed from marker as this will

ease reassembly). Remove the Disconnect Lock Pin (#23C) and the Disconnect Pin (#23B). Hold

down the Striker Plug (#28I) and Thumb Adjuster (#28291/#28293), as internal parts may be

spring-loaded. As you pull the cocking knob out of the receiver, the Cocking Bolt (#17H) and

Striker (#18B) will also be removed.

7. Lubricate o-rings #9 and #19A with a few drops of paintball oil only.

8. Reassemble parts back into the marker. Note: when putting the Cocking Bolt and Striker back

into the marker, you will need to apply pressure behind the bolt while pulling the trigger at the

same time. This will allow the Bolt and Striker to be properly installed back into the receiver.

9. When you are finished shooting the marker, first, unload the marker of all paintballs. Note: there

may be a ball in the receiver; take a couple of shots in a safe direction to make sure that the

barrel and receiver are empty. Second, put the barrel plug into the barrel. Put the safety on and

slowly unscrew the air source tank. Caution: do not unscrew the tank valve from the tank. Doing

so may cause serious injury or death.

10. Empty the hopper or remove the hopper off the marker to stop the flow of paintballs in the marker.

CAUTION

• This paintball marker is NOT a toy. It can cause serious injury

or death.

• Recommend at least 18 years of age to purchase this product.

• Install a barrel plug in the barrel when not actually playing.

• All persons using this product, or within range while this

product is being used, must wear eye and face protection

specifically designed for paintball.

• Never shoot a person who is not wearing proper protection.

• Treat every paintball marker as if it were loaded.

• Never look down the barrel of the marker.

• Keep the paintball marker on safe until ready to shoot.

• Always remove gas source before disassembly.

• Fire only 0.68 caliber paintballs from this product.

• Read this manual and air system warning before using this product.

• Any modifications or tampering of original factory parts will void all warranties and

liabilities from Kingman.

• Always turn power off or put marker on safety when marker is not in use.

• Always make certain the bolt is in the un-cocked position when marker is not in use.

• Transfer this instruction manual upon change of marker ownership.

IMPORTANT

• Firing velocity may vary according to altitude and climate conditions.

• BEFORE using your marker in play, you must always first perform a “SAFE VELOCITY TEST”. This can only be accomplished

by using a testing device called a “Velocity Chronograph” and can be performed by the dealership where you purchased this

product or at a local paintball playing field.

• Note: This product is intended to be used at a velocity no greater than 300 feet per second (FPS).

• Recommended velocity is 280 FPS or less.

• This product is NOT intended to be used at any distance less than 25 feet.

• This paintball marker may have excess gas after removal of the tank. Please remove all paintballs and discharge the

remaining gas safely.

Name    Telephone ( )

Address

City State Zip Country

Your age E-mail address  Occupation

Product name and model

What other brand(s) of markers do you own?

Why did you purchase this Kingman marker?

Avg # of times you play paintball per month

Have you purchased products from the Internet within the last 6 months?

Comments/Suggestions:   

What is the next paintball product you intend to buy?

What are your hobbies (other than paintball)?

What are some magazines you like to read?

KINGMAN Warranty Registration

PLEASE COMPLETE AND RETURN THIS FORM, ALONG WITH A COPY OF YOUR PURCHASE

RECEIPT, WITHIN 15 DAYS OF PURCHASE SO THAT WE MAY VALIDATE YOUR ONE YEAR

LIMITED WARRANTY.

Mail to: Kingman Group

 14010 Live Oak Avenue

 Baldwin Park, CA 91706 U.S.A.

CO2/HP AIR TANK WARNING

WARNING

• VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED

PERSONNEL.

• BOTTLE MUST BE RETESTED SEE CO2/HP TANK LABEL FOR

RETEST DATE!

• Improper use, filling, storage or disposal of this cylinder may result in

death, personal injury and property damage.

• This cylinder must be filled only by properly Trained personnel in

accordance with CGA Pamphlets P.1 and G-6.3 available from the

Compressed Gas Association WWW.CGANET.COM

• Do not over pressurize. Do not expose pressurized cylinder to

temperatures in excess of 130 degrees F.

• Do not expose cylinder to corrosive materials and do not clean with

caustic cleaners.

• Do not alter this cylinder in any way.

• Cylinders heated to a temperature of 250 degrees F or more must be

condemned or requalified in accordance with test defined in CFR-49.

• Keep cylinder out of reach of children.

• The valve should NEVER be detached from the canister. Should this

occur, please seek assistance from a trained airsmith immediately.

• This tank is intended for paintball use only.

14010 Live Oak Avenue, Baldwin Park, CA 91706

Telephone: 626.430.2300 Fax: 626.851.8530

Website: www.Kingman.com

WARRANTY STATEMENT

Kingman warranties to the original customer purchaser that this product is free from defects in

material and workmanship under normal use and service for a period of 12 months from the

original date of purchase by the initial owner/purchaser. For warranty to be effective, customer

must return the enclosed warranty registration card, along with a copy of the purchase receipt,

within fifteen days of purchase. Kingman agrees to repair or replace (at its discretion) any product

within a reasonable period of time. This warranty does not cover o-rings, scratches, nicks,

normal wear and tear of parts, any modifications or normal fading of anodizing or damage caused

by dropping or hitting of products. This warranty shall not apply if it is shown by Kingman that the

consumer caused the defect or malfunction because of misuse. This warranty only covers original

factory parts. Any modifications or tampering of original factory parts will not be covered by this

warranty. Any damage caused by water will not be covered by this warranty. Warranty work can

only be conducted by Kingman technician or Kingman authorized technicians. If product needs

repair, package it carefully and send together with your name, address, phone number and a brief

description of the malfunction to:

TROUBLESHOOTING

ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED PROBLEMS:

a. The pressure in the tank is too low or too high.

b. Need lubrication. (See OPERATION GUIDE in P4)

c. #19A (striker o-ring) is damaged. Replace with new Kingman or Kingman-approved o-ring.

(Note: the #19A O-ring cannot be substituted by a tank o-ring or a #9 o-ring).

d. Need to clean barrel and upper chamber or the receiver.

e. Paintball may be defective (i.e. expired, change shape)

f. #9 (bolt o-ring) is damaged or the o-ring has expanded or swelled. Replace with a

new o-ring.

g. After ball breaks, remove all parts from UPPER chamber of receiver, wipe parts clean, and

reassemble parts into receiver. Also make sure to clean barrel with squeegee

HELPFUL HINTS

• Always remove air tank before any disassembly of your marker. DO NOT remove #14

(valve body) unless specific valve body repairs are needed. If needed, remove valve body

with a long, soft-tipped object such as the eraser end of a pencil. DO NOT remove the valve

body with a screwdriver as it will damage the valve body and cause air leaks. (Note: #15

screw must be removed prior to taking out the valve body).

• Air leaks are usually cause by a damaged valve body or damaged cup seal (#12). Replace

with new valve body and/or cup seal if necessary.

• To assure marker is assembled properly, follow the schematic drawing or place parts in

order during disassembly. Parts assembled backwards or placed in the wrong order will

cause marker to malfunction.

SPYDER XTRA

+

+

SEMI-AUTO

spyder

spyder

spyder

01

02F

2704G

05B

28041

28061

28063

28081

28085

28082

07

09

10A

11

12

Spyder Barrel Plug

12" Barrel (Silver)

Ball Stopper w/Detent Cover (Silver)

M4 x 6 Screw (#4B,4C,47D) (Silver)

Direct Feed (Silver)

Receiver (Shutter Blue)

Receiver (Cobalt Blue)

Vertical Adapter (Shutter Blue)

Vertical Adapter (Cobalt Blue)

Low Pressure Chamber (Silver)

M5 x 14 Screw w/ Washer

O-Ring #015 80D

Valve Spring

Cup Seal Guide

Cup Seal

ITEM # Name of Parts

13

14

15

16

17H

18B

19A

20

21

22

22B

23B

23C

25

26A

Valve Pin

Valve Body

Valve Body Screw

M5 x 12 Screw (Black)

Venturi Cocking Bolt

Striker Bolt (#19A)

Striker O-Ring (#18A/#18B)

Barrel O-Ring (Black)

Bolt Pin

Bolt Screw

M4 X 8 Screw (Black)

Quick Disconnect Pin

Disconnect Pin Lock

Striker Spring

Striker Buffer (#18A/#18B)

ITEM # Name of Parts

27

27A

28I

28291

28293

29B

31B

31X

Striker Spring Guide

Flat Disc

Striker Bolt Plug (Silver)

Thumb Adjuster w/ screw (Shutter Blue)

Thumb Adjuster w/ screw (Cobalt Blue)

Lock Screw

Trigger Sear

Deluxe Trigger Frame

ITEM # Name of Parts

32E

33C

33F

2835

28353

2335

36D

36E

45 Grip Cover

Grip Cover Screws (M3 x 10)

Nut Screw

C/A Adapter (Shutter Blue)

C/A Adapter (Cobalt Blue)

Deluxe Drop Forward (Silver)

5/32" x 5/8" Screw

5/32" x 7/8" Screw (Black)

ITEM # Name of Parts

37A

37B

37C

37D

37J

2841

28441

28442

28444

38A

39B

42F

47G

48

49

49A

5814

Filter O-Ring

Air Filter

Disconnect O-Ring #011(Black)

Plastic Washer (Disconnect Hose)

Disconnect Hose

Spare Parts Kit

Gas Thru Fore Grip (Silver)

Mini Fore Grip (Shutter Blue)

Mini Fore Grip (Cobalt Blue)

Safety Button Set (Medium)

Cocking Rod (Silver)

Male to Male Metric Adapter

Sight Rail w/ Beaver Tail (Silver)

Trigger Roll Pin (Large)

Sear Roll Pin (Medium)

Secondary Sear Roll Pin (Small)

Double Trigger

ITEM # Name of Parts

37C

2835/28353

0101

1002F1002F

2020

28081/

28085

28081/

28085

2808228082

0909 0909 0909

0909

2844128441

28442/2844428442/28444

37C37C

37J37J 37D37D 37A37A 37B37B

33C33C

33C33C

32E32E

1616

0707

05B05B

05B05B

04GA04GA

05B05B

05B05B

23C23C

0909 0909

2222

26A26A2525

18B18B

2727

27A27A

29B29B

28291/2829328291/2829328I28I

19A19A

1616

31X31X

33F33F

23352335

36D36D36D36D

36E36E36E36E

33F33F

39B39B

2121

28061/2806328061/28063

2804128041

1515 38A38A

58145814

42F42F

0909 0909

10A10A 1111 1212 1313

1414

4848

4949 4949

31B31B

23B23B

49A49A

010101

1002F1002F1002F

202020

28081/

28085

28081/

28085

28081/

28085

280822808228082

090909 090909 090909

090909

284412844128441

28442/2844428442/2844428442/28444

37C37C37C

37J37J37J 37D37D37D 37A37A37A 37B37B37B

33C33C33C

33C33C33C

32E32E32E

161616

070707

05B05B05B

05B05B05B

04GA04GA04GA

05B05B05B

05B05B05B

23C23C23C

090909 090909

222222

26A26A26A252525

18B18B18B

272727

27A27A27A

29B29B29B

28291/2829328291/2829328291/2829328I28I28I

19A19A19A

161616

31X31X31X

33F33F33F

233523352335

36D36D36D36D36D36D

36E36E36E36E36E36E

33F33F33F

39B39B39B

212121

28061/2806328061/2806328061/28063

280412804128041

151515 38A38A38A

581458145814

42F42F42F

090909 090909

10A10A10A 111111 121212 131313

141414

484848

494949 494949

31B31B31B

23B23B23B

49A49A49A

22B22B

17H17H

47G47G