Stanley Black and Decker 1DK0JB0AX 1DX0JB0AX User Manual Module 1DK0JB0AX Installation Guide V1

Download:
Mirror Download [FCC.gov]
Document ID	2875309
Application ID	VRWdUdBMMSXXZRVChal/uA==
Document Description	Module 1DK0JB0AX Installation Guide V1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.45kB (155662 bits)
Date Submitted	2016-01-17 00:00:00
Date Available	2016-01-19 00:00:00
Creation Date	2016-01-13 09:33:51
Producing Software	Acrobat Distiller 10.0.0 (Windows)
Document Lastmod	2016-01-13 09:33:51
Document Title	Microsoft Word - Module 1DK0JB0AX Installation Guide V1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ahauck

Purpose
This document describes the installation process of the 1DK0JB0AX Module in Stanley
Black & Decker battery packs.
NOTICE: Installation of this module may only be made by qualified
Stanley Black & Decker Installer. This is not a field upgrade, and must be
done at the Stanley Black & Decker factory.
To comply with FCC and Industry Canada RF exposure limits for general
population / uncontrolled exposure, the antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 5 mm from all persons
and must not be operating in conjunction with any other antenna or transmitter.
If the module is used in a multi-transmitter or simultaneous transmission host
then the module must be evaluated and approved to one of the host platform
exposure conditions. (Mobile exposure, Portable exposure or Mixed Mobile and
Portable exposure).
Pour se conformer aux limites d'exposition aux RF de la FCC et d'Industrie
Canada pour la population générale / exposition non contrôlée, l'antenne (s)
utilisé pour cet émetteur doit être installé pour fournir une distance de séparation
d'au moins 5mm de toutes les personnes et opérant en conjonction avec une
autre antenne ou émetteur.
Si le module est utilisé dans un environnement multi-émetteur ou hôte de la
transmission simultanée alors le module doit être évaluée et a approuvé l'une
quelconque des conditions d'exposition de la plate-forme d'accueil. (Exposition
mobile, l'exposition portable ou l'exposition mobile et portable mixte).
End Product Marking and Instruction Manual
The 1DK0JB0AX Module is labeled with its own FCC ID and IC Certification number. If
these numbers are not visible upon installation in the end product the outside of the end
product must display a reference to the Module numbers in a visible area.
For example:
Contains FCC ID: YJ71DK0JB0AX
Contains IC: 9082A-1DK0JB0AX
The User Manual for the end product must include the following information in a prominent
location:
This device is granted for configurations in which the antennas used for this
transmitter must be installed to provide a separation distance of at least 5mm
from all person and not be co-located with any other transmitters except in
accordance with FCC and Industry Canada multi-transmitter product
procedures.
Le manuel d'utilisation pour le produit final doit comporter les informations suivantes dans
unendroit bien en vue:
Ce dispositif est accordée pour les configurations dans lesquelles les antennes
utilisées pour cet émetteur doit être installé pour fournir une distance de séparation
d'au moins 5mm de toute personne et ne pas être co-localisés avec d'autres émetteurs
sauf en conformité avec la FCC et d'Industrie Canada produit de l'émetteur multiples
procédures.
FCC Notice
FCC ID: YJ71DK0JB0AX
Compliance Statement (Part 15.19)
This device complies with Part 15
of the FCC Rules. Operation is
subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Notice
IC: 9082A-1DK0JB0AX
Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
Section 7.1.3 of RSS-GEN
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is
subject to the following two conditions: 1) this device may not cause interference, and 2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
Section 7.1.2 du CNR-GEN
En vertu de la réglementation de l'industrie du Canada, cet émetteur de radio ne peut
fonctionner à l'aide d'une antenne de un type et un maximum (ou moins) Gain approuvé pour
l'émetteur par Industrie Canada. A réduire les interférences radio potentielles aux autres
utilisateurs, le type d'antenne et son gain doivent être si choisi que la puissance isotrope rayonnée
équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie.
Section 7.1.3 du CNR-GEN
Cet appareil est conforme norme Industrie Canada RSS exempts de licence (s). Son
fonctionnement est soumis aux deux conditions suivantes: 1) cet appareil ne doit pas
provoquer d'interférences, et 2) cet appareil doit accepter toute interférence, y compris
les interférences pouvant provoquer un fonctionnement indésirable du dispositif.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : ahauck
Create Date                     : 2016:01:13 09:33:51-06:00
Modify Date                     : 2016:01:13 09:33:51-06:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - Module 1DK0JB0AX Installation Guide V1
Creator                         : ahauck
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Document ID                     : uuid:8988c8f7-1d24-4072-a5e8-5fd238adb616
Instance ID                     : uuid:b2337cd2-b0cf-4e1f-8c02-6eec2b20c176
Page Count                      : 3

EXIF Metadata provided by EXIF.tools