Stanley Black and Decker N457147J Bluetooth Tool Module User Manual
Stanley Black & Decker Bluetooth Tool Module
User Manual
Purpose
This document describes the installation process of the DeWalt Bluetooth Drill
Module, N457147J.
Notice: Installation of this module may only be performed by a qualified Stanley
Black & Decker Installer. Installation is not a field upgrade and must be done at
the manufacturing facility of the end-product tool.
To comply with the FCC and Industry Canada RF exposure limits for general
population/uncontrolled exposure, the antenna used in the module must be
installed as to provide a separation distance of at least 5 mm from all persons and
must not be operating in conjunction with any other antenna or transmitter.
If the module is used in a multi-transmitter or simultaneous transmission host
then the module must be evaluated and approved to one of the host platform
exposure conditions (Mobile, Portable, or Mixed Mobile and Portable exposures).
Pour se conformer aux limites d’exposition aux RF de la FCC et d’Industrie Canada
pour la population générale/exposition non contrôlée, l’antenne utilisé pour cet
émetteur doit être installé pour fournir une distance de séparation d’au moins 5
mm de toutes les personnes et opérant en conjunction avec une autre antenne
ou émetteur.
Si le module est utilisé dans un environment multi-émetteur ou hôte de la
transmission simultanée alors le module doit être evaluée et a approuvé l’une
quelconque des conditions d’exposition de la plate-forme d’accueil. (Exposition
mobile, l’exposition portable, ou l’exposition mobile et portable mixte).
End-Product Marking and Instruction Manual
The DeWalt Bluetooth Drill Module is labeled with its own FCC ID and IC number.
If these numbers are not visible upon installation in the end-product the outside
of the end-product must display a reference to the Module numbers in a visible
area.
For example: Contains FCC ID: YJ7-N457147J
Contains IC: 9082A-N457147J
The User Manual for the end-product must include the following information
(bold text) in a prominent location:
This device is granted for configurations in which the antennas used for this
transmitter must be installed to provide a separation distance of at least 5 mm
from all persons and not be co-located with any other transmitters except in
accordance with FCC and Industry Canada multi-transmitter product
procedures.
Le manuel d’utilisation pour le produit final doit comporter les informations
suivantes dans unendroit en vue:
Ce dispositive est accordée por les configurations dans lesquelles les antennes
utilisées pour cet émettuer doit être installé pour fournir une distance de
séparation d’au moins 5 mm de toute personne et ne pas être co-localisés avec
d’autres émetteurs sauf en conformité avec la FCC et d’Industrie Canada produit
de l’émetteur multiples procédures.
FCC Notice
FCC ID: YJ7-N457147J
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
FCC Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105(b))
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Notice
IC: 9082A-N457147J
Section 8.3 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Section 8.4 of RSS-GEN
This Device complies with Industry Canada License-exempt RSSs. Operation is
subject to the following two conditions:
1. The device may not cause interference, and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
Section 7.1.2 du CNR-GEN
En vertu de la réglementation de I’industrie du Canada, cet émetteur de radio
ne peut fonctionner à l’aide d’une antenne de un type et un maximum (ou
moins) Gain approuvé pour l’émetteur par Industrie Canada. A réduire les
interférences radio potentielles aux autres utilisateurs, le type d’antenne et son
gain doivent être si choisi que la puissance isotrope rayonnée équivalente (PIRE)
ne dépasse pas ce qui est nécessaire pour une communication réussie.
Section 7.1.3 du CNR-GEN
Cet appareil est conforme norme Industrie Canada RSS exempts de license (s).
Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne doit pas provoquer d’interférences, et
2. Cet appareil doit accepter toute interférence, y compris les interférences
pouvant provoquer un fonctionnement indésirable du dispositif.