Star Solutions M1900-1 iPA - CDMA 1X Bi-directional Amplifier - 1900 MHz User Manual Regulatory

Star Solutions International Inc iPA - CDMA 1X Bi-directional Amplifier - 1900 MHz Regulatory

UserManual.wiki >

Star Solutions >

M1900-1 User Manual >

users manual 2 HTML Version

1. users manual 1
2. users manual 2

users manual 2

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 1 of 14

MovingMedia® 2000

iCell CDMA2000 1X

iPA 1900 MHz

Translating

Bi-directional Amplifier

BASIC INSTALLATION GUIDE

RELEASE 4.5

DRAFT 0.1

PART NUMBER NXX0306XXX

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 2 of 14

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 3 of 14

any means or used to make any derivative work (such as translation, transformation, or adaptation) without prior written

permission from UTStarcom, Inc.

UTStarcom, Inc. reserves the right to revise this documentation and to make changes in content from time to time without

obligation on the part of UTStarcom, Inc. to provide notification of such revision or change.

UTStarcom, Inc. provides this documentation without warranty of any kind, either implied or expressed, including, but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. UTStarcom may make improvements

or changes in the product(s) and/or the program(s) described in this documentation at any time.

UNITED STATES GOVERNMENT LEGENDS:

If you are a United States government agency, then this documentation and the software described herein are provided to

you subject to the following:

United States Government Legend: All technical data and computer software is commercial in nature and developed solely

at private expense. Software is delivered as Commercial Computer Software as defined in DFARS 252.227-7014 (June

1995) or as a commercial item as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in

UTStarcom's standard commercial license for the Software. Technical data is provided with limited rights only as provided in

DFAR 252.227-7015 (November 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or

deface any portion of any legend provided on any licensed program or documentation contained in, or delivered to you in

conjunction with, this User Guide.

UTStarcom, the UTStarcom logo and MovingMedia 2000 are registered trademarks of UTStarcom, Inc. and its subsidiaries.

Other brand and product names may be registered trademarks or trademarks of their respective holders.

Regulatory

This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

received including interference that may cause undesired operation.

Where appropriate, the use of the equipment is subject to the following conditions:

CAUTION! Unauthorized modifications or changes not expressly approved by UTStarcom could void compliance with

regulatory rules, and thereby your authority to use this equipment.

WARNING (EMI) - United States FCC Information - This equipment has been tested and found to comply with the

limits pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON,

the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician

To comply with Maximum Permissible Exposure (MPE) requirements, the maximum composite output from the

antenna cannot exceed ____ Watts EIRP and the antenna must be permanently installed in a fixed location that

provides at least ____ cm of separation from all persons.

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 4 of 14

1 PREFACE

1.1 Objective

This document provides installation and configuration instructions for setting up an iCell-

CDMA2000 1X iPA system. It covers physical installation only.

1.2 Organization

The major sections of this guide are as follows:

Table 1-1: Organization Table

Chapter Title Description

Chapter 1 Preface Introduction to the Installation Guide.

Chapter 2 iCell System Description Describes the System components

Chapter 3 iPA Physical Installation Provides mechanical installation

and wiring instructions.

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 5 of 14

1.3 Reference Documents

The following table summarizes the applicable reference documents.

Table 1-2: Reference Documents

Ref. Title Number

1 User Manual Pico BTS

2 iCell CDMA2000 1X Alarms and Statistics

3 iCell CDMA2000 1X Configuration Guide

1.4 Acronyms and Abbreviations

The following table summarizes the acronyms and abbreviations used throughout the

document.

Table 1 -3: Acronyms and Abbreviations

1PPS One Pulse Per Second

AAA Authentication, Authorization, and Accounting function

Abis Protocol interface between sBSC and BTS

ASN.1 The language used to define the MIB of the NE

EM Element Manager

GPS Global Positioning System

HLR Home Location Register

sBSC iCell Base Station Controller

BTS iCell Base Station Transceiver Subsystem

BSS Base Station Subsystem (BSC+BTS)

iMB iCell Main Board

IOS Inter-Operability Standard; A-Interface between sBSC and MSC

IP Internet Protocol

iPA iCell Power Amplifier

MIB Management Information Base

MS Mobile Station (phone)

MSC Mobile Switching Center

NE Network Element or agent

NOC Network Operations Center

OID Object Identifier

OMC Operations & Maintenance Center

PA Power Amplifier

MovingMedia 2000 iCell Macro with iPA Installation Guide

Page 6 of 14

PDSN

PSTN

SMSC

SNMP

SNTP

TBD

TCP

TOD

Packet Data Serving Node

Public Switch Telephone Network

Radio Frequency

Short Message Service Center

Simple Network Management Protocol

Simple Network Timing Protocol To Be

Defined

Transmission Control Protocol

Time Of Day

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 7 of 14

2 iCell MACRO SYSTEM DESCRIPTION

This chapter provides an iCell system description.

2.1 Introduction

The iCell is an IP-based solution for CDMA2000 1X radio access networks.

The iCell system provides the overall functionality of a CDMA2000 1X Base station

transceiver subsystem (BTS) and soft base station controller (sBSC), providing an IP

over Ethernet interface to the core network. For Macro coverage small footprint iPA Bi-

directional amplifier is added to the basic BTS configuration. Figure 2-1 shows the

system architecture.

Figure 2-1: iCell Macro BSS using iPA

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 8 of 14

2.2 iPA 1900 MHz System Components

The iPA is only used when the iCell is installed in a 19" rack-mounted configuration. The

iPA is a single sector bi-directional amplifier that incorporates:

A high power amplifier (HPA)

Two low noise amplifiers (LNA) for receive diversity, frequency

conversion and selectivity capabilities (for each sector).

On the receive side, the iPA down-converts the PCS band (1900MHz) incoming signals of

each sector to a fixed IF for signal enhancement, then up-converts them to Cellular band

(800 MHz) which are then output to the Pico cell receive paths. On the transmit side, the

iPA takes the Cellular band transmit signal of each sector from the Pico BTS transmit path,

down-converts to a fixed IF for signal enhancement, then up-converts to PCS band for

transmission.

Figure 2-2: iCell 800 MHz Pico BTS interfaced to Translating iPA 1900 MHz (3 sector

Case shown using 3 iPAs)

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 9 of 14

3 BTS PHYSICAL INSTALLATION

3.1 General

This chapter provides physical installation and wiring instructions for the iPA.

3.2 Unpacking

Upon receipt of, and before opening the iCell packages, inspect for any damage that

might have occurred during shipping. If the package shows any signs of external

damage or rough handling, notify your carrier's representative.

CAUTION

All modules are susceptible to electrostatic discharge (ESD) even while

installed. Take the necessary precautions to minimize electrostatic damage

while handling modules.

Carefully remove all parts and hardware out of the

packages. Carry out a full inventory before installation

procedure starts.

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 10 of 14

3.3.1 BTS 19" Rack Mount

See Figure 3-1 and Figure 3-2.

1. Insert the BTS 1X 19" unit into a 19" rack. Secure with four NF10 screws.

2. Connect BTS 19" Rack Mount according to paragraph 3.4.2.

Figure 3-1: BTS 19' Rack Mont Rear View

Figure 3.3: iPA Front View

Figure 3.4: iPA Rear View (AC input Power) (-48v DC version also available)

Figure 3.2: BTS 19” Rack Mount Front View

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 11 of 14

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 12 of 14

3.4 Interface Connections

3.4.1 BTS and iPA Interface Connections

Verify that the power switch is off on both the iPA and the BTS unit

3.4.2 BTS to iPA Interface Connection

Figure 3-1 illustrates the wiring diagram of the BTS and iPA for Macro coverage.

Table 3-1 provides the wiring parameters.

Figure 3.1: BTS and iPA wiring diagram

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 13 of 14

Table 3-1: iBTS 19" Wiring

iBTS Destination

Name Type

Cable

MCN Name Type

S3 RX1 SMA 45-89330-M3 iPA RX3 Diversity SMA

S3 TX/RX0 SMA 45-89330-M3 iPA TX/RX3

Diversity SMA

S2RX2 SMA 45-89330-M3 iPA RX2Diversity SMA

S2 TX/RX0 SMA 45-89330-M3 iPA TX/RX2

Diversity SMA

S1 RX2 SMA 45-89330-M3 iPA

RX1 Diversity SMA

S1 TX/RX0 SMA 45-89330-M3 iPA

TX/RX1 Diversity SMA

iPA 1 RJ45S 45-89331-M2 iPA Com 1 DB-9

iPA 2 RJ45S 45-89331-M2 iPA Com 2 DB-9

iPA 3 RJ45S 45-89331-M2 iPA Com 3 DB-9

19.2 MHz SMA 45-89330-M3 iPA SMA 19.2

MHz

Pri Eth RJ45S Standard CAT5 Ethernet Switch RJ45

Console RJ45S 45-89331-M2 PC DB9

GPS TOD RJ45S 45-89332-M3 GPS DB9 Serial DB9

1 PPS IN 1 SMA GPS 1 PPS BNC

AC Power

Power

Supply

Switching

363-06097-0015

363-02155-0002

External Source

Power

NOTE

All SMA connectors that are not connected should be terminated.

3-9

iWAN Installation Guide

MovingMedia 2000 iCell Macro with iPA Installation Guide Page 14 of 14

3.4.2.1 Connecting to iPA for three sector case:

To Connect the iBTS to the iPA:

Connect the iBTS iPA 1 RJ-45 connector to the iPA COM 1 DB-9

connector with cable MCN 45-89330-M3.

Connect the iBTS iPA 2 RJ-45 connector to the iPA COM 2 DB-9

connector with cable MCN 45-89330-M3.

Connect the iBTS iPA 3 RJ-45 connector to the iPA COM 3 DB-9

connector with cable MCN 45-89330-M3.

Connect the iBTS S1 RX1 SMA Connector to the iPA RX1 Diversity SMA