Steren Electronics 750-905O-JHE Little Wing User Manual
Steren Electronics International, LLC Little Wing
User Manual
Little Wing
User Guide
Little Wing User Manual 2
Setting up your Little Wing
1. POWER ON/OFF
To turn ON your Little Wing speakers, simply press the power button on the bottom of the
speaker. The LED will light up and flash between blue and red and an audio cue will indicate
the system is on. To turn the Little Wing speakers off, once again simply press the power
button on the bottom of the speaker. The LED will fade out indicating power is OFF.
2. CHARGING AND BATTERY
To obtain optimum power capacity, the Little Wing speakers should be charged using the
provided dual USB Micro to USB Y cable. To charge the Little Wing speakers, plug the two
ends of the micro USB cable into the back of each Little Wing speaker. Plug the single USB
into any USB charging device or into a computer. While charging, the LED will glow solid
RED. When the Little Wing is fully charged, the LED light will turn off.
3. VOLUME
The volume of the Little Wing speakers is controlled by the Bluetooth® device that is currently
connected
Little Wing User Manual 3
4. BLUETOOTH®
Single Pairing: Only turn on ONE Little Wing speaker by moving switch to far right
position (Sync). Wait for the unit to “BEEP” and then move switch to middle “On” position.
Once powered on, the LED on the back of the Little Wing will rapidly blink BLUE, indicating
the device is in pairing mode. On your mobile device select “LittleWing”. Your speaker is now
connected and can be used for playback. Disconnect by turning the power switch to the OFF
position or un-pairing from your mobile device.
Connected: Once Little Wing is successfully paired and connected, the LED will glow solid
BLUE.
Dual Pairing (RECOMMENDED): Turn on both Little Wing speakers by
moving the power switch to ON on both speakers. The LEDs on the back of both speakers will
blink BLUE for a few seconds while the devices search for each other. Once the Little Wing
speakers are successfully paired to each other, the LED will glow solid BLUE for a few
seconds, followed by a chime and notification that they are connected to each other and
identify the Left and Right speakers. On your mobile device select “LittleWing”. Your speaker
is now connected and can be used for playback. Disconnect by turning the power switch to
the OFF position or un-pairing from your mobile device.
Connected: Once successfully paired and connected, the LED will glow solid BLUE.
OFF
ON
Little Wing User Manual 4
Connection Troubleshooting: If unable to connect to speakers with chosen pairing
mode (Single/Dual) you need to clear the stored pairing information. Move the switch on both
speakers to the far right (Sync) to clear all data. Wait 5 seconds and then move the switch to the
OFF position on both units. Follow instructions above to re-pair in the desired mode.
Technical Specifications
Weight: 250g Power: 3W x 2
Input Voltage: 5V Driver size: 1.5 inch x 2
USB Rechargeable Bluetooth: 2.1+ EDR
Charging Time: 3 to 5 Hours RF Range: 10M (33feet)
Batter Life: 4.0 hours, 6 00mAh 3.7V, Lithium Portable Bluetooth Speaker Pair
Important Safety Information
1. READ these instructions.
2. DO NOT use this apparatus near water.
3. CLEAN ONLY with dry cloth.
4. DO NOT use near any heat sources such as radiators, heat registers, stoves, or any other device that may produce excessive heat.
5. PROTECT the USB cord from being walked on or pinched, particularly at the plugs and the point where it exits from the speaker.
6. ONLY USE attachments/accessories specified by the manufacturer.
7. UNPLUG this device during lightning storms or when unused for long periods.
WARNING: To reduce the risk of electrical shock, do not expose device to water.
WARNING: No open flame sources – such as candles – should be placed on the product..
Warning Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.