Steren Electronics BL-775-104 QUADCOPTER 2.4GHz User Manual RC106

Steren Electronics International, LLC QUADCOPTER 2.4GHz RC106

Users Manual

BL-775-104
BL-775-104
After you place the mobilephone on the holder ,open the software and you can enjoy the real time video showed on your mobilephone .2.Press the controller to clicks into mobilephone fixing component .1.Put the back of the mobilepnone fixing component to match the antenna and handle of the controller .
Return Take Photo RecordVideo Media Speed :30%/60%/100%Altitude hold Gravity Sensor Mode MenuVirtual Rocker
HOW TO START YOUR QUADCOPTERHOW TO LAND YOUR QUADCOPTERWay 1: After playing, control the drone to the ground and keep the throttle at the lowest position for 3-4 seconds or until the motor stop working. Finally switch off the transmitter and drone. Way 2: For fast turn off or any emergency, pull the left control stick to the left bottom and right control stick to the right bottom, then the motor will stop working at once. Please do not do this operation while the product in the sky, or it can fall down suddenly due to non-working motor.Step 2:Press the ON/OFF power switch up.Step1:Connect the battery to the battery port.Step 3: Push the throttle lever to the highest position, And then pull it back to the lowest position. There will be one clear sound from the transmitter, this shows that the quadcopter has entered into the pre-fly state.Step 4: Pull the left control stick to the left bottom and right control stick to the right bottom, then the motor will be ready to work. This is an extra operation for the product with altitude hold function.TIPS:For the drone with altitude hold function, which means the drone can keep in the same flying altitude,the left control stick(accelerator) will self-return to the center to keep balance. Player can push it up or pull it down to control the drone at the altitude that he wants it to be when release the left control stick(accelerator).
M
Tested to comply with FCC standards .FOR HOME OR OFFICE USE .This device complies with part 15 of the FCC Rules .Operation is subject to the following two conditions ：（1）This device may not cause harmful interference and （2）This device must accept any interference received , including interference that may cause undesired operation .
WARNING: Changes or modifications to this unit are not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC ID : 2ABDSBL-775-104
WARNING: Changes or modifications to this unit are not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC ID : 2ABDSBL-775-104
WARNING: Changes or modifications to this unit are not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC ID : 2ABDSBL-775-104
WARNING: Changes or modifications to this unit are not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC ID : 2ABDSBL-775-104
WARNING: Changes or modifications to this unit are not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC ID : 2ABDSBL-775-104

Navigation menu