Strix Systems ACCESS-ONE-21 802.11 a/g Wireless, Mesh Type Networking Device User Manual ows hardware installation manual
Strix Systems, Inc. 802.11 a/g Wireless, Mesh Type Networking Device ows hardware installation manual
Contents
Users Manual V
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 743852 |
| Application ID | /VJZw2OTEbnVh39dK/HRwg== |
| Document Description | Users Manual V |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 99.29kB (1241129 bits) |
| Date Submitted | 2007-01-04 00:00:00 |
| Date Available | 2007-01-04 00:00:00 |
| Creation Date | 2006-04-13 10:57:41 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2006-04-13 12:08:49 |
| Document Title | ows_hardware_installation_manual.book |
| Document Creator | FrameMaker 6.0 |
| Document Author: | Bill Wareing |
Access/One® Network OWS Field Installation Strix Outdoor Wireless System (OWS) Field Installation April 13th, 2006 210-0014-01 Rev. F Copyright © 2003 – 2006 Strix Systems, Inc. 26610 Agoura Road Calabasas, CA 91302 USA http://www.strixsystems.com OWS Field Installation Copyright Notice Copyright © 2003 – 2006 Strix Systems, Inc. All rights reserved. This document may not be reproduced or disclosed in whole or in part by any means without the written consent of Strix Systems, Inc. Access/One Network is a registered trademark of Strix Systems, Inc. All other trademarks and brand names are marks of their respective holders. FCC Notice The enclosed wireless network device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This wireless network device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless network device generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this wireless network device does cause harmful interference to radio or television reception, which can be determined by turning the wireless network device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ◗ Reorient or relocate the receiving antenna. ◗ Increase the separation between the wireless network device and the affected receiver. ◗ Connect the wireless network device into an outlet on a circuit different from that to which the receiver is connected. ◗ Consult the dealer or an experienced radio/TV technician for help. Other Notices Industry Canada Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. VCCI Notice This is a Class B wireless network device based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this wireless network device is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the wireless network device according to the instruction manual. European Community (EC) Directives and Conformity This wireless network device is in conformity with the Essential Requirements of R&TTE Directive 1999/5/EC of the European Union. ii OWS Field Installation OWS Field Installation Non-Modification Statement Unauthorized changes or modifications to Strix devices are not permitted. Modifications to Strix devices will void the warranty and may violate FCC regulations. RF Exposure Requirements To ensure compliance with FCC RF exposure requirements, the antenna used for this wireless network device must be installed to provide a separation distance of a minimum of 2 meters (6.56 feet) or more from all persons, and must not be co-located or operated in conjunction with any other antenna or radio transmitter. Installers and end-users must follow these installation instructions. Safety Warnings This unit must be installed by a trained professional installer only. Read the following safety warnings before commencing an installation. General Safety Warning Always be aware of electrical power lines! You can be killed if any antennas come near electrical power lines. Carefully read and follow all instructions in this manual. By performing these installation instructions, you may be exposed to hazardous environments and high voltage. Use caution when installing the Strix OWS product. Electrical Power Warning This unit must be installed by a trained professional installer only. Read the installation instructions before you connect the wireless network device to its power source. Lightning Activity Warning Do not connect or disconnect cables during periods of lightning activity. For each antenna, a surge protective device meeting IEC 61000-4-5, Level 4 or IEEE C 62.41 A3/B3 requirements must be used to prevent potential damage from very high surges (for example, surges caused by lightning). Explosive Device Proximity Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment. OWS Field Installation iii OWS Field Installation Antenna Placement Warning Do not locate any antenna near overhead power lines or other electric light or power circuits, or where the antenna can come into contact with such circuits. When installing antennas, take extreme care not to come into contact with such electrical circuits, as they can cause serious injury or death. For the correct installation and grounding of antennas, please refer to national and local codes (for example, US:NFPA 70, National Electrical Code, Article 810; in Canada: Canadian Electrical Code, Section 54). Ground Warning You must ALWAYS install an external grounding wire. The ground connection must be complete before connecting power to the OWS enclosure—a simple continuity check between the enclosure and the ground termination point can confirm this. Grounding of the OWS must comply with National Electrical Code (NEC) requirements, unless local codes in your area take precedence over the NEC code. Power Cord Assembly Caution An assembled power cord is not supplied with the OWS. The power cord must be assembled by a professional installer, and the final assembly must comply with National Electrical Code (NEC) requirements, unless local codes in your area take precedence over the NEC code. Battery Caution This product contains a non-rechargeable, non-user-serviceable lithium ion battery. Exercise caution to avoid shorting the terminals of this device. Consult local laws and regulations for the proper disposal of batteries in your area. Solar Shield A solar shield is required for any installation where the OWS product will receive direct exposure to sunlight. Failure to install a solar shield where required may cause damage to the product and will void its warranty. Contact your Strix authorized distributor or Strix Systems for Solar Shield model numbers and ordering information. iv OWS Field Installation OWS Field Installation Limited Warranty Strix Systems, Inc. (“Strix”) warrants the Access/One Indoor Wireless System (“IWS”) and Outdoor Wireless System (“OWS”): (i) the hardware (“Hardware”) will be free of defects in materials and workmanship from the date of shipment as set forth below and (ii) the embedded software (“Firmware”) to the Hardware and any separately provided software product (“Software”) are provided “AS-IS” and such items will substantially conform to their respective published product documentation (collectively the “Product”) for the periods indicated below, commencing (as applicable) on the date of shipment. Covered Product IWS products Warranty Period 12 months (Including but not limited to the BMEx, WM11x, NWSV-x, Antennas, AMECs, MTKIT, PSWW, SLCDT and SLCKIT) OWS2400/OWS3600 12 months OWS11xx (Radio Board)/OWS-NSxx (Network Servers) 12 months Repaired or Replacement Items 90 days, or the balance of the original item warranty, whichever is the greater This limited warranty extends only to the original user of the Product and such user's sole and exclusive remedy and the entire liability of Strix, at its option, will be to repair or replace the Hardware or component thereof and in the case of Firmware or Software Strix will make available the then available updated version of the Firmware or Software. Notwithstanding the foregoing, in no event does Strix warrant that the Product will operate with any software or hardware other than that provided by Strix or specified in the applicable Product documentation, that the Product is error free or will operate without problems or interruptions, or that the, Product will be free of vulnerability to intrusion or attack, or that the Product will satisfy any party's own specific requirements. The repair or replacement of the Product does not include any labor or other costs related to the subsequent installation thereof. The obligations of Strix hereunder are conditioned upon the return of the Hardware in accordance with the Strix then-current Return Material Authorization (RMA) procedures (please contact your authorized Strix Systems reseller for return instructions). Repair or replacement of the defective Product or parts thereof shall neither extend nor decrease the warranty period. Exceptions The foregoing limited warranties of the Product do not apply if the Product (i) has been altered or modified, except by Strix or its duly trained and authorized service provider, (ii) has not been installed, operated, repaired, or maintained in accordance with written instructions of Strix, (iii) has been subjected to abnormal physical or electrical stress, misuse, negligence or accident, (iv) has been operated outside of the environmental specifications for the Product or (v) is related to configuration of customer's network beyond that necessary to the use or installation of the Strix Products. The Strix limited Firmware or Software warranty does not apply to Firmware or Software corrections or upgrades. Repair of Products or the supply of updated Firmware or Software requested after the expiration of the warranty period shall be at then current Strix repair or update charges. OWS Field Installation OWS Field Installation DISCLAIMER; LIMITATION OF LIABILITY EXCEPT FOR THE WARRANTIES SPECIFICALLY DESCRIBED HEREIN, STRIX DISCLAIMS ANY AND ALL WARRANTIES AND GUARANTEES, EXPRESS, IMPLIED OR OTHERWISE, ARISING, WITH RESPECT TO THE PRODUCTS OR SERVICES DELIVERED HEREUNDER, INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY, THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTY OF NON-INFRINGEMENT OF THE INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. LIABILITY OF STRIX FOR LOSS UNDER THIS CONTRACT IS LIMITED TO THE TOTAL AMOUNT PAID TO STRIX BY CUSTOMER DURING THE PREVIOUS CALENDAR YEAR. STRIX WILL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE OR IMPUTED NEGLIGENCE, STRICT LIABILITY OR PRODUCT LIABILITY) OR OTHERWISE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF USE, LOSS OF DATA, BUSINESS INTERRUPTION, LOSS OF REVENUE, LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH ANY OF THE PRODUCTS OR OTHER GOODS OR SERVICES FURNISHED BY STRIX UNDER THIS AGREEMENT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. STRIXSYSTEMS® (including the design) and ACCESS/ONE® are registered trademarks of Strix Systems, Inc. vi OWS Field Installation OWS Field Installation Table of Contents Copyright Notice .................................................................................................................................... ii FCC Notice ............................................................................................................................................ ii Other Notices ........................................................................................................................................ ii Safety Warnings ....................................................................................................................................iii General Safety Warning ..................................................................................................................iii Electrical Power Warning ...............................................................................................................iii Lightning Activity Warning .............................................................................................................iii Explosive Device Proximity Warning ..............................................................................................iii Antenna Placement Warning .......................................................................................................... iv Ground Warning ............................................................................................................................ iv Power Cord Assembly Caution ....................................................................................................... iv Battery Caution ............................................................................................................................... iv Solar Shield .................................................................................................................................... iv Limited Warranty ................................................................................................................................... v OWS Field Installation ................................................................................................................. 1 Theory of Operation ............................................................................................................................... 1 Important Safety Information .................................................................................................................. 1 Planning Your Installation ...................................................................................................................... 2 Local Guidelines ............................................................................................................................. 2 Site Surveys ..................................................................................................................................... 2 Power Source .................................................................................................................................. 2 Installing the OWS Enclosure ................................................................................................................. 3 Mounting the OWS on a Vertical Pole ............................................................................................. 3 Mounting the OWS on a Wall ......................................................................................................... 7 Installing Antennas ................................................................................................................................. 8 Notes About Antenna Installations ................................................................................................... 8 Maximum Power Settings for Antennas ............................................................................................ 9 Channels for IEEE 802.11b/g ..................................................................................................... 9 Channels for IEEE 802.11a ...................................................................................................... 10 Attaching an Omni Antenna Directly to the OWS Enclosure ......................................................... 12 Mounting a Directional Antenna on a Pole .................................................................................... 14 Mounting a Sectored Antenna on a Pole ........................................................................................ 16 Mounting an Omni Antenna on a Pole .......................................................................................... 19 Antenna Connector Wiring Configurations ........................................................................................... 22 OWS Field Installation vii OWS Field Installation Physical Layout (Enclosure) ...........................................................................................................22 Physical Layout (Wireless Modules) ............................................................................................... 23 Routing the Antenna Cables ................................................................................................................. 23 Grounding the OWS Enclosure ............................................................................................................ 24 Configuring the Power Cord ................................................................................................................. 25 AC Wiring Configurations .............................................................................................................. 27 Connecting the Ethernet Cable ............................................................................................................. 28 Powering Up the OWS ......................................................................................................................... 30 Powering Up from an AC Power Source ........................................................................................ 30 Powering Up from a DC Power Source .......................................................................................... 30 OWS Product Specifications ................................................................................................................ 31 Appendix I: Setting the Output Power .................................................................................................. 32 Appendix II: Installing the Band Pass Filter ........................................................................................... 33 Index .......................................................................................................................................... 35 viii OWS Field Installation OWS Field Installation OWS Field Installation This field installation manual provides instructions for installing the Strix OWS 2400 and OWS 3600 products safely and is intended for trained technical professionals. You must read the Safety Warnings on page iii before commencing with the installation. Theory of Operation The Strix Systems, Access/One® Network OWS provides up to 3 independent channels of 802.11g support, and 3 independent channels of 802.11a support through its external connections. This configuration allows the installer to separate the client 802.11g traffic from the backhaul traffic which is carried through the 802.11a channels. As shipped from the factory, the OWS is self-configuring and self-healing. In addition, multiple configuration options are possible and the installer should refer to the Access/One® Network User's Guide (part number 210-0007-01) for detailed information about these configurations. Important Safety Information The Federal Communications Commission (FCC) with its action in ET Docket 96-8 has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC certified equipment. All Strix products, including the OWS, meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. The proper operation of this wireless device, according to the instructions found in this manual and the associated Access/One® Network software User’s Guide, result in user exposure that is substantially below the FCC recommended limits. The following are guidelines to ensure safe operation of the Strix OWS product: ◗ Do not touch or move the antenna(s) while the unit is transmitting or receiving. ◗ Do not hold any component containing a radio such that the antenna is very close to or touching any exposed parts of the body—especially the face or eyes—while transmitting. ◗ Do not operate the OWS or attempt to transmit data unless the antenna (or a 50 ohm terminator) is connected, otherwise the wireless module(s) may be damaged. ◗ Usage in specific environments: – Do not operate any wireless equipment near unshielded blasting caps or in an explosive environment. – The use of wireless devices in hazardous locations is limited to the constraints posed by the safety directors or such environments. – The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). – The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. ◗ The Strix OWS must only be used with Strix-approved components and antennas, or equivalent. OWS Field Installation OWS Field Installation Planning Your Installation To ensure safe and durable wiring, the installation of the Strix OWS must follow the appropriate electrical and building codes. Observe the National Electrical Code (NEC) requirements, unless local codes in your area take precedence over the NEC code. Local Guidelines The Strix OWS is a radio device and therefore susceptible to interference that can reduce throughput and range. Follow these simple guidelines to optimize product performance: ◗ Install the OWS in an area where trees, buildings, and large steel structures do not obstruct radio signals to and from the antenna(s). Direct line-of-sight operation is always best. ◗ Install the OWS away from microwave ovens or other devices operating in the 2.4 GHz range. ◗ Install the OWS away from other possible source of 2.4 GHz WLAN interference, such as cordless phones, home surveillance equipment, frequency-hopping (FHSS) and DSSS Local Area Network transceivers, electronic news gathering video links, radars, amateur radios, land mobile radio services, local government sties (for example, law enforcement), fixed microwave services, local TV transmission, and private fixed point transmitters. Site Surveys Due to variations in product configuration, placement, and the physical environment, each installation is unique. Before installing the Strix OWS, we recommend that you perform a site survey to determine the optimum placement of the product to achieve the best possible range, coverage and network performance. Consider the following points: ◗ Data Rates—Sensitivity and range are inversely proportional to data bit rates. The maximum wireless range is achieved at the lowest data rate. A decrease in receiver threshold sensitivity occurs as wireless data increases. ◗ Antenna Type and Placement—Using the correct antenna configuration is a critical factor when trying to maximize wireless range. As a general rule, the range increases in proportion to the antenna height and gain. ◗ Physical Environment—Clear or open areas offer better wireless coverage than closed or filled areas. The less cluttered the operating environment, the greater the range. ◗ Obstructions—A physical obstruction, such as a building or tree, can block or hinder wireless services. Avoid placing antennas in locations where there is an obstruction between the sending and receiving antennas. ◗ Building Materials—Wireless penetration is influenced by the building materials used in construction. For example, drywall construction permits greater range than concrete blocks. Steel and alloy materials can be a barrier to wireless signals. ◗ Diversity—The Strix OWS supports RX diversity, which requires two antennas. Power Source The Strix OWS supports both AC and DC input power. OWS Field Installation OWS Field Installation Installing the OWS Enclosure This section provides instructions for mounting the OWS enclosure. Mounting the OWS on a Vertical Pole Parts Required ◗ OWS enclosure. ◗ Pole. ◗ 2 vertical mounting brackets. ◗ 4 screws, for attaching the mounting brackets to the OWS enclosure. ◗ 2 U-bolt assemblies, for mounting the OWS enclosure to a standard 1 7/8 inch diameter steel pole. ◗ 2 straps, for mounting the OWS enclosure to a pole with a diameter greater than 1 7/8 inches. Tools Required ◗ Flat blade screwdriver ◗ 7/16 inch nut wrench ◗ 5/16 inch nut driver Mounting Brackets (x2) 1. Attach the vertical mounting brackets (2) to the OWS enclosure. Screws (x4) 2. Secure the vertical mounting brackets to the OWS enclosure with the four screws (2 for each bracket). Tighten all four screws to 10–12 lbf.ft (1.38–1.66 kgf.m). OWS Field Installation OWS Field Installation 3. For a standard 1 7/8 inch diameter steel pole installation, use the 2 U-bolt assemblies to attach the enclosure to the pole via the vertical mounting brackets—finger tighten only. If installing the OWS on a wider pole (for example, a utility pole), go directly to Step 7—skip Steps 3 through 6. Tip: You may find it easier to loosely attach the U-bolts to the brackets, then slide the completed enclosure assembly over the pole (instead of holding the enclosure against the pole and attaching each U-bolt separately). U-Bolt Assembly (x2) Includes: ◗ U-bolt ◗ Washers (2) ◗ Nuts (2) 4. Adjust the OWS enclosure to the desired position on the pole (up and down or rotational). OWS Field Installation OWS Field Installation 5. Use a 7/16 inch nut wrench to tighten the U-bolts (4 nuts) and secure the OWS enclosure in place. Tighten all four nuts to 10–12 lbf.ft (1.38–1.66 kgf.m). When tightening the U-bolts, ensure that the bolts are not twisted—the ends of each U-bolt should be protruding through the bracket evenly (the same distance). Tighten (4 places) 6. Check that the U-bolts are tight and that the OWS enclosure is securely anchored to the pole. OWS Field Installation OWS Field Installation Straps (x2) 7. For poles wider than 1 7/8 inch diameter, use two straps (hose clamps)—not provided. Feed one strap through each of the vertical mounting brackets. Recommended straps: Type 301 SS with Type 305 SS screw, 3.125 x 6 inches, available from McMaster-Carr (part number 54155K36). 8. Loosely attach the OWS enclosure to the pole with the 2 straps. Adjust the enclosure to the desired position on the pole (up and down or rotational). Use a flat blade screwdriver or 5/16 inch nut driver to tighten both straps to 10–12 lbf.ft (1.38–1.66 kgf.m). OWS Field Installation OWS Field Installation Mounting the OWS on a Wall Parts Required ◗ OWS enclosure. ◗ 4 nylon hangers, for mounting the OWS enclosure to a wall. ◗ 4 screws (10-32 x 0.375), for attaching the nylon hangers to the enclosure. Tools Required ◗ Flat blade screwdriver ◗ Power drill and drill bit (if necessary) 1. Attach the 4 nylon hangers to the OWS enclosure using the 4 screws provided. Nylon Hanger (x4) 2. Mount the OWS enclosure to any wall surface, ensuring that the unit is level and secure (4 places). If mounting the enclosure to a masonry wall, you will need a power drill, masonry drill bit, and wall plugs. OWS Field Installation OWS Field Installation Installing Antennas This section provides instructions for installing and connecting antennas. The antennas shown in this section are a representative sample only and are provided as a guideline for installation—your specific antenna(s) may be different, in which case refer to the instructions provided with the antenna(s). Antenna Warning Antennas must be installed by a trained professional installer only. Do not locate any antenna near overhead power lines or other electric light or power circuits, or where the antenna can come into contact with such circuits. When installing antennas, take extreme care not to come into contact with such electrical circuits, as they can cause serious injury or death. For the correct installation and grounding of antennas, please refer to national and local codes (for example, US:NFPA 70, National Electrical Code, Article 810; in Canada: Canadian Electrical Code, Section 54). Applying Power Before an Antenna is Connected Do not apply power to the transmitter until the antenna is connected, otherwise permanent damage may result. Strong RF Fields are Present When the unit is operation, avoid standing directly in front of the antenna. Strong RF fields are present when the transmitter is ON. Notes About Antenna Installations Read the following notes before installing any antenna. ◗ The system installer should always ensure that antenna radiation patterns do not overlap. ◗ A sector antenna should point towards the center of the sector covered by the antenna. ◗ Fixed point-to-point backhaul antennas should point towards the desired Strix Systems Access/One® Network device intended for the backhaul connection. ◗ Unused antenna ports must be terminated with a 50 ohm terminator. ◗ Only antennas approved by Strix Systems (or equivalent) may be used with the Access/One® Network Outdoor Wireless System (OWS). ◗ Only one antenna may be used on each antenna port. ◗ When installing antennas that require mounting brackets and U-bolts, it is easier to loosely attach the U-bolts to the brackets, then slide the completed antenna assembly over the pole (instead of holding the assembly against the pole and attaching each U-bolt separately—mounting brackets are shipped with the U-bolts pre-assembled. For this reason, do not install an omni antenna at the top of the pole before installing any directional/sectored antennas that will reside below it. OWS Field Installation OWS Field Installation ◗ Depending on the selected antenna(s) for your application, it may be necessary to configure the output power of your OWS 2400 or OWS 3600 product. It is the installer’s responsibility to ensure the output power is set correctly for the chosen antenna(s). To set the output power, go to Appendix I: Setting the Output Power on page 32. Operation of the OWS 2400 or OWS 3600 in a manner other than as represented here is a violation of FCC rules. Maximum Power Settings for Antennas The following are the maximum power settings for each antenna1 type, based on wireless technology, antenna type and channels: Channels for IEEE 802.11b/g 12 dBi Omni Antenna (2.4 GHz) Power Level (dBm) * Channel Identifier Frequency (MHz) Filter 2412 CCK ODFM Yes Half (+24dBm) Half (+23dBm) 2417 Yes Half (+24dBm) Half (+23dBm) 2422 Yes Half (+24dBm) Half (+23dBm) 2427 Yes Half (+24dBm) Half (+23dBm) 2432 Yes Half (+24dBm) Half (+23dBm) 2437 Yes Half (+24dBm) Half (+23dBm) 2442 Yes Half (+24dBm) Half (+23dBm) 2447 Yes Half (+24dBm) Half (+23dBm) 2452 Yes Half (+24dBm) Half (+23dBm) 10 2457 Yes Half (+24dBm) Half (+23dBm) 11 2462 Yes Half (+24dBm) Half (+23dBm) * Listed power level settings are average power. 1. To comply with FCC standards for broadband emissions, a band pass filter is required for 802.11g transmissions on channels 1 and 11 in the United States (RF Linx Corporation part number 2400BPF-8-FB or equivalent), and for 802.11a transmissions in the 5.725 - 5.850 GHz band when using the 23 dBi Patch Panel antenna in the United States (K&L Microwave part number 6C50-5787.5/U120-n/n or equivalent). For additional information, go to Appendix II: Installing the Band Pass Filter on page 33. OWS Field Installation OWS Field Installation 16.4 dBi Sector Antenna (2.4 GHz) Power Level (dBm) * Channel Identifier Frequency (MHz) Filter 2412 CCK ODFM Yes Quarter (+21dBm) Quarter (+20dBm) 2417 Yes Quarter (+21dBm) Quarter (+20dBm) 2422 Yes Quarter (+21dBm) Quarter (+20dBm) 2427 Yes Quarter (+21dBm) Quarter (+20dBm) 2432 Yes Quarter (+21dBm) Quarter (+20dBm) 2437 Yes Quarter (+21dBm) Quarter (+20dBm) 2442 Yes Quarter (+21dBm) Quarter (+20dBm) 2447 Yes Quarter (+21dBm) Quarter (+20dBm) 2452 Yes Quarter (+21dBm) Quarter (+20dBm) 10 2457 Yes Quarter (+21dBm) Quarter (+20dBm) 11 2462 Yes Quarter (+21dBm) Quarter (+20dBm) * Listed power level settings are average power. Channels for IEEE 802.11a 12 dBi Omni Antenna (5.25 – 5.35 GHz) Power Level (dBm) * Channel Identifier Frequency (MHz) Filter 52 5260 No Quarter (+17dBm) 56 5280 No Quarter (+17dBm) 60 5300 No Quarter (+17dBm) 64 5320 No Quarter (+17dBm) ODFM * Listed power level settings are average power. 10 OWS Field Installation OWS Field Installation 12 dBi Omni Antenna (5.725 – 5.85 GHz) Power Level (dBm) * Channel Identifier Frequency (MHz) Filter 149 5745 No Half (+23dBm) 153 5765 No Full (+26dBm) 157 5765 No Full (+26dBm) 161 5805 No Full (+26dBm) 165 5825 No Half (+23dBm) ODFM * Listed power level settings are average power. 23 dBi Patch Panel Antenna (5.25 – 5.35 GHz) Power Level (dBm) * Channel Identifier Frequency (MHz) Filter 52 5260 No Minimum (+5dBm) 56 5280 No Minimum (+5dBm) 60 5300 No Minimum (+5dBm) 64 5320 No Minimum (+5dBm) ODFM * Listed power level settings are average power. 23 dBi Patch Panel Antenna (5.725 – 5.85 GHz) Power Level (dBm) * Channel Identifier Frequency (MHz) Filter 149 5745 Yes Half (+23dBm) 153 5765 Yes Full (+26dBm) 157 5765 Yes Full (+26dBm) 161 5805 Yes Full (+26dBm) 165 5825 Yes Half (+23dBm) ODFM * Listed power level settings are average power. OWS Field Installation 11 OWS Field Installation Attaching an Omni Antenna Directly to the OWS Enclosure Parts Required ◗ Omni Antenna, with optional adapter (no special tools required). 1. If necessary, connect the optional antenna adapter to the desired antenna port at the bottom of the OWS enclosure. Hand tighten, making sure the adapter is firmly in place—you can use an adjustable wrench, but do not overtighten or damage the adapter. Adapter 12 OWS Field Installation OWS Field Installation 2. Thread the omni antenna onto the antenna adapter—the electrical connection between the antenna and the enclosure is established via the adapter. There are no external cables required when attaching an omni antenna directly to the OWS enclosure. See also, Antenna Connector Wiring Configurations on page 22. Adapter Omni Antenna OWS Field Installation 13 OWS Field Installation Mounting a Directional Antenna on a Pole Parts Required ◗ Pole. ◗ Directional antenna (includes adjustable mounting bracket). ◗ 2 straps, for mounting the antenna to a standard 1 7/8 inch diameter steel pole. ◗ Antenna cable. Tools Required ◗ Flat blade screwdriver 1. Attach the 2 straps (hose clamps) to the mounting bracket. Antenna Straps (x2) 2. Mount the antenna to the pole with the 2 straps. Adjust the antenna to the desired position, then use a flat blade screwdriver or 5/16 inch nut driver to tighten both straps to 10–12 lbf.ft (1.38–1.66 kgf.m). 14 OWS Field Installation OWS Field Installation Vertical Adjustment 3. Using a flat blade screwdriver, fine tune the position of the antenna by adjusting the mounting bracket along the vertical axis and the horizontal axis. Tighten the mounting bracket adjustment screws to 10–12 lbf.ft (1.38–1.66 kgf.m). Horizontal Adjustment 4. Connect one end of the antenna cable to the directional antenna, then connect the other end of the cable to an available antenna port on the OWS enclosure. See also, Antenna Connector Wiring Configurations on page 22 and Antenna Connector Wiring Configurations on page 22. Antenna Cable Connect between the directional antenna and a free antenna port on the OWS enclosure OWS Field Installation 15 OWS Field Installation Mounting a Sectored Antenna on a Pole Parts Required ◗ Pole. ◗ Sectored antenna. ◗ 2 U-bolt assemblies, for mounting the antenna to a standard 1 7/8 inch diameter steel pole. ◗ Adjustable mounting bracket (including antenna mounting plate and U-bolt assemblies). ◗ Antenna cable. Tools Required ◗ 7/16 inch nut wrench 1. If not already assembled, assemble the adjustable mounting bracket. Secure the antenna mounting plate to the antenna body with 4 x 7/16 inch screws and spring washers. Use a 7/16 inch nut wrench to tighten the screws to 10–12 lbf.ft (1.38–1.66 kgf.m). Attach the mounting bracket to the antenna mounting plate with 6 x 7/16 inch screws and spring washes—finger tighten only. The U-bolts are pre-assembled with the mounting bracket. Antenna Mounting Plate Secure to antenna body with 4 x 7/16 inch screws and spring washers 16 Mounting Bracket Attach to mounting plate with 6 x 7/16 inch screws and spring washers—finger tighten only OWS Field Installation OWS Field Installation 2. Attach the sectored antenna to the pole—finger tighten only. 3. Adjust the antenna to the desired position on the pole (up and down or rotational). 4. Use a 7/16 inch nut wrench to tighten the U-bolts (4 nuts) and secure the sectored antenna in place. Tighten all four nuts to 10–12 lbf.ft (1.38–1.66 kgf.m). When tightening the U-bolts, ensure that the bolts are not twisted—the ends of each U-bolt should be protruding through the mounting bracket evenly (the same distance). OWS Field Installation 17 OWS Field Installation Vertical Adjustment (up to 30 degrees) 5. If necessary, use a 7/16 inch nut wrench to loosen the 6 bolts on the adjustable mounting bracket. Make your vertical adjustment to the sectored antenna (up to 30 degrees), then tighten all 6 bolts to 10–12 lbf.ft (1.38–1.66 kgf.m). 6. Connect one end of the antenna cable to the sectored antenna, then connect the other end of the cable to an available antenna port on the OWS enclosure. See also, Antenna Connector Wiring Configurations on page 22 and Antenna Connector Wiring Configurations on page 22. Antenna Cable Connect between the sectored antenna and a free antenna port on the OWS enclosure 18 OWS Field Installation OWS Field Installation Mounting an Omni Antenna on a Pole Parts Required ◗ Pole. ◗ Omni antenna. ◗ 2 U-bolt assemblies, for mounting the antenna to a standard 1 7/8 inch diameter steel pole. ◗ Mounting bracket. ◗ Antenna cable. Tools Required ◗ 1/2 inch nut wrench ◗ 7/8 inch nut wrench Omni Antenna 1. Attach the omni antenna to the mounting bracket, using the washer and locknut provided. Mounting Bracket The U-bolts are pre-assembled with the mounting bracket. Washer 2. Use a 7/8 inch nut wrench to tighten the locknut to 10–12 lbf.ft (1.38–1.66 kgf.m). U-Bolt Assembly (x2) Includes: ◗ ◗ ◗ ◗ U-bolt Plain washers (2) Spring washers (2) Nuts (2) Locknut OWS Field Installation 19 OWS Field Installation 3. Attach the omni antenna to the pole—finger tighten only. 4. Adjust the omni antenna to the desired position on the pole (up and down or rotational). 5. Use a 1/2 inch nut wrench to tighten the U-bolts (4 nuts) and secure the omni antenna in place. Tighten all four nuts to 10–12 lbf.ft (1.38–1.66 kgf.m). When tightening the U-bolts, ensure that the bolts are not twisted—the ends of each U-bolt should be protruding through the mounting bracket evenly (the same distance). Tighten (4 places) 20 OWS Field Installation OWS Field Installation 6. Check that the U-bolts are tight and that the omni antenna is securely anchored to the pole. 7. Connect one end of the antenna cable to the omni antenna, then connect the other end of the cable to an available antenna port on the OWS enclosure. See also, Antenna Connector Wiring Configurations on page 22 and Antenna Connector Wiring Configurations on page 22. Antenna Cable Connect between the omni antenna and a free antenna port on the OWS enclosure OWS Field Installation 21 OWS Field Installation Antenna Connector Wiring Configurations The following table shows the antenna connector wiring configurations for the OWS family of products: Antenna Connector Wiring Product Enclosure Connector Module Connector 2400 series and 3600 series ant. 1 G ANT1 – J24 2400 series and 3600 series ant. 2 A ANT1 – J21 2400 series and 3600 series ant. 3 G ANT1 – J24 2400 series and 3600 series ant. 4 A ANT1 – J21 2400 series and 3600 series ant. 5 G ANT1 – J24 2400 series and 3600 series ant. 6 A ANT1 – J21 3600 series only ant. 7 A ANT1 – J21 3600 series only ant. 8 G ANT1 – J24 Physical Layout (Enclosure) The following diagram shows the physical layout of antenna connectors on the OWS 3600 enclosure (the OWS 2400 does not have the ant. 7 or ant. 8 antenna options). ant. 1 ant. 2 ant. 3 ant. 4 ant. 5 ant. 6 ant. 7 ant. 8 22 OWS Field Installation OWS Field Installation Physical Layout (Wireless Modules) The following diagram shows the physical layout of antenna connectors on the OWS wireless modules (top view, looking down on module when the enclosure door is open). G ANT1 G ANT2 A ANT2 A ANT1 Routing the Antenna Cables It is important that when you install the antenna cables they are not hanging randomly and that the cables are secured. This section provides a sample routing scenario. 1. If mounting the OWS on a pole, route the antenna cables through the OWS enclosure mounting bracket and secure with cable ties. Ensure that the cables are not twisted. 2. If mounting the OWS on a wall, the cables should be fixed to the wall with a suitable cable clamp. OWS Field Installation 23 OWS Field Installation Grounding the OWS Enclosure This section provides instructions for grounding the OWS enclosure. Grounding Caution You must ALWAYS install an external grounding wire. The ground connection must be complete before connecting power to the OWS enclosure—a simple continuity check between the enclosure and the ground termination point can confirm this. Grounding of the OWS must comply with National Electrical Code (NEC) requirements, unless local codes in your area take precedence over the NEC code. Parts Required ◗ Ground wire assembly (with ring terminator)—must be 18 gauge AWG wire, or greater. Tools Required ◗ 3/16 inch nut wrench ◗ Wire stripper (if necessary) 1. Connect the ground wire to the ground terminal on the bottom of the OWS enclosure. Make sure the lock washer is in place and that the nut is securely fastened. 2. Connect the other end of the ground wire to a grounding strap attached to a grounded surface, such as a cold water pipe (or other suitable ground termination point, compliant with NEC and local standards). On pole-mounted OWS enclosures, if the pole (or pole stand) is already grounded, you may use one of these items as the ground termination point. 24 Ground Wire Connect to a suitable ground termination OWS Field Installation OWS Field Installation Configuring the Power Cord This section provides instructions for configuring the power cord (not supplied) for either AC or DC operation, and connecting the power cord to the OWS enclosure. Electrical Power Warning This unit must be installed by a trained professional installer only. Read the installation instructions before you connect the wireless network device to its power source. Power Cord Assembly Caution The power cord must be assembled by a professional installer, and the final assembly must comply with National Electrical Code (NEC) requirements, unless local codes in your area take precedence over the NEC code. Parts Required ◗ AC or DC power cord (not supplied), cut to the desired length. ◗ AC/DC plug assembly. Tools Required ◗ Wire stripper ◗ Flat blade screwdriver Pin 5 Pin 1 Pin 4 Pin 2 1. Review the pin connections. ◗ ◗ ◗ ◗ ◗ Pin 1 – AC Neutral Pin 2 – DC Positive (+) Pin 3 – Ground Pin 4 – DC Negative (–) Pin 5 – AC Line The example opposite shows an AC plug assembly. Pin 3 2. Assemble the plug and connect the plug to the power cord of your choice for the electrical configuration you need, either AC or DC. Plug Assembly Power Cord The power cord must be assembled by a professional installer. Collar Shield Locking Ring OWS Field Installation 25 OWS Field Installation 3. Attach the plug to the enclosure’s power receptacle. Power Receptacle Plug 4. Turn the locking ring of the plug and hand tighten to make the connection. 5. Install an appropriate AC or DC connector at the other end of the power cord. Locking Ring The AC1 connector you use at the other end of the power cord depends on the AC power source you are connecting to. Refer to AC Wiring Configurations on page 27. 1. If using an AC power source, to comply with FCC standards for radiated spurious EMF emissions a 30 MHz to 1 GHz ferrite core must be attached to the AC power cord in a double-turn configuration (as close to the OWS enclosure as possible. A suitable ferrite core for this purpose can be obtained from Fair-Rite Products Corporation, part number 0444164181 (round cable snap-it model). 26 OWS Field Installation OWS Field Installation AC Wiring Configurations The following diagrams show alternative wiring configurations for AC input power options. 120 VAC Single Phase (two wire service) 240 VAC Single Phase (two wire service) 208 VAC Three Phase (two wire service – grounded/Wye) 240 VAC Three Phase (two wire service – Delta) OWS Field Installation 27 OWS Field Installation Connecting the Ethernet Cable This section provides instructions for configuring the CAT5 Ethernet cable. Parts Required ◗ Plenum-rated CAT5 Ethernet cable, cut to the desired length (not supplied). ◗ RJ45 plug assembly. Tools Required ◗ Wire stripper 1. Review the pin connections. ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ 28 Pin 1 – TXD+ (TX Data) Pin 2 – TXD- (TX Data) Pin 3 – RXD+ (RX Data) Pin 4 – Not used Pin 5 – Not used Pin 6 – RXD- (RX Data) Pin 7 – Not used Pin 8 – Not used ◗ Continuity checker Pin 4 Pin 5 Pin 3 Pin 6 Pin 2 Pin 7 Pin 1 Pin 8 OWS Field Installation OWS Field Installation 2. Assemble the RJ45 plug/cable. ◗ ◗ ◗ ◗ ◗ Item 1 – Shielded RJ45 plug Item 2 – Gasket seal Item 3 – Plug holder Item 4 – Coupling ring Item 5 – Seal assembly When assembling the plug, take care not to lose the gasket seal (item 2)—it must be in place when the assembly is complete. 3. Install an RJ45 plug at the other end of the cable. 4. Perform a continuity check on each pin to verify that the Ethernet cable1 has been assembled correctly. 5. Unscrew the protective cap, then connect the Ethernet cable to the OWS enclosure. Turn the coupling ring clockwise (1/4 turn) to make the connection. Cap The connection is locked when you feel and hear a click. 1. To comply with FCC standards for radiated spurious EMF emissions a 30 MHz to 1 GHz ferrite core must be attached to the Ethernet cable in a double-turn configuration. A suitable ferrite core for this purpose can be obtained from Fair-Rite Products Corporation, part number 0444167281 (round cable snap-it model). OWS Field Installation 29 OWS Field Installation Powering Up the OWS This section provides instructions for powering up the OWS from both an AC and DC power source. Powering Up from an AC Power Source Important Note (AC Power) AC input: 100 – 240 VAC (50/60 Hz) at 1.0 Amp maximum, supplied by a separate branch circuit with 2 Amp over-current protection (2 Amp circuit breaker). The OWS must always be grounded before applying power to the unit—see Grounding the OWS Enclosure on page 24. 1. Verify that the AC service voltage is 120 VAC to 240 VAC. 2. Check that the power is turned OFF at the designated circuits. 3. If necessary, install 1/2 inch liquid-tight conduit from the power source to within 3 feet of the OWS, then connect the conduit to a junction box. The conduit and junction box must be IEEE/ANSI compliant and suitable for outdoor use. 4. Connect the OWS power cord to the AC supply. 5. Close the enclosure’s door (the OWS door interlock will actuate). 6. Turn ON the AC supply. Powering Up from a DC Power Source Important Note (DC Power) DC input: 12 – 24 VDC at 9.0 Amp maximum, supplied by an external separate 250 VA power-limited (or less) and isolated DC source with 15 Amp over-current protection (15 Amp circuit breaker). The OWS must always be grounded before applying power to the unit—see Grounding the OWS Enclosure on page 24. 1. Verify that the DC service voltage is 12 VDC to 24 VDC. 2. Check that the power is turned OFF at the designated circuits. 3. If necessary, install 1/2 inch liquid-tight conduit from the power source to within 3 feet of the OWS, then connect the conduit to a junction box. The conduit and junction box must be IEEE/ANSI compliant and suitable for outdoor use. 4. Connect the OWS power cord to the DC supply. 5. Close the enclosure’s door (the OWS door interlock will actuate). 6. Turn ON the DC supply. 30 OWS Field Installation OWS Field Installation OWS Product Specifications WIRELESS ENVIRONMENTAL ◗ Wireless Standards: IEEE 802.11a/g ◗ Frequency Bands: 802.11a - 5.25 - 5.35 GHz - 5.725 - 5.850 GHz 802.11g - 2.4 - 2.4835 GHz (Americas, FCC) ◗ Data Rates (Mbps): - 6, 9, 12, 18, 24, 36, 48, 54 (802.11a/g) - 12, 18, 24, 36, 48, 72, 96, 108 (802.11a Turbo) ◗ Wireless Medium: 802.11a – OFDM, 802.11g – DSSS ◗ Modulation: - 802.11a: BPSK, QPSK, 16 QAM, 64 QAM - 802.11g: DBPSK, DQPSK, CCK ◗ Operating Channels: 802.11a - 12 (Americas, FCC), includes 3 turbo channels 802.11g - 11 (Americas, FCC) ◗ Transmit Power: Configuration dependent—contact Strix ◗ Receiver Sensitivity: Configuration dependent—contact Strix ◗ LO (crystal) Frequency Stability: +/-10PPM within normal op. range of 0° to 55°C ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ ELECTRICAL ◗ Power Input: Auto-sensing 120/240 VAC, 50/60 Hz, single phase, with ANSI/IEEE C62.41 category C3 integrated branch circuit protection ◗ AC Power Consumption: 25W typical, 90W maximum ◗ DC Input: 12/24V, 9A maximum PROTECTION CIRCUITS ◗ Antenna Lightning Protection (optional): < 9µJ for 6kV/3kA @ 8/20µs waveform ◗ Electrical Protection: ANSI/IEEE C62.41, UL 1449 2nd edition; 10kA @ 8/20 µs waveform, 36kA per phase; L-L, L-N, L-PE ◗ Data Protection: EN61000-4-2 Level 4 ESD Immunity EN61000-4-5 Level 4 AC Surge Immunity EN61000-4-4 Level 4 Elect. Fast Transient Burst Immun. EN61000-4-3 EMV Field Immunity OWS Field Installation Operating Temperature: -40°C to +55°C Storage Temperature: -55°C to +85°C Humidity: 10% to 90% non-condensing Weather Rating: IP67 weather tight Wind Survivability: <165 mph Wind Loading (165 mph): <1024 newtons Salt/Fog/Rust Resistance: Mil-STD-810F 509.4 Shock & Vibration: ESTI 300-192-4 spec T41.E Class 4M3 and Mil-STD-810 ◗ Transportation: ISTA 2A and Mil-STD-810 PHYSICAL ◗ Dimensions: 3600 Series: 14” high x 12” wide x 8” deep (without accessories) 2400 Series: 12” high x 10” wide x 6” deep (without accessories) ◗ Weight: 3600 Series: 16.5lbs (7.48 Kg) 2400 Series: 14.5lbs (6.58 Kg) ◗ NEMA 4 rated for outdoor enclosures SECURITY ◗ Authentication: 802.1x support, including RADIUS client, EAP-MD5, EAP-TLS, and PEAP-TTLS, WPA ◗ Encryption: IEEE 802.11i (WPA) with AES, and WEP REMOTE MANAGEMENT ◗ Web, CLI and SNMP interfaces ◗ Supports BOOTP, DHCP, Telnet, SSH, HTTP, HTTPs, and FTP ◗ SNMP: MIB II, 802.11 MIB, and Strix private MIBs APPROVALS ◗ ◗ ◗ ◗ ◗ ◗ ◗ FCC CFR47 Part 15, Class B Industry Canada RSS210 EN60950 cTUVus Listed I.T.E UL 579/IEC 60529 IP67, rated for outdoor use UL 1449 2nd edition / IEC 60664-1 CAN/CSA-C22.2 60950-00 VCCI Class B WARRANTY ◗ One year parts and labor 31 OWS Field Installation Appendix I: Setting the Output Power Use the following procedure to set the output (transmit) power for the chosen antenna: 1. Establish a Telnet connection with the selected wireless module (radio). 2. Log in to the radio. 3. Type the command get power. The system displays the current power settings for the selected radio. If the radio is set to the desired power setting, no further action is required and you can log out, otherwise go to Step 4. The following list shows the available power settings: ◗ Full – sets the maximum (normal) transmit power. This is the default setting. ◗ Half – sets the transmit power to a fractional half of the full power. ◗ Quarter – sets the transmit power to a fractional quarter of the full power. ◗ Eighth – sets the transmit power to a fractional eighth of the full power. ◗ Minimum – sets the transmit power to its minimum. 4. To set the power output for the selected radio, type the command set power and append the desired setting to the command. For example, to set the output power to minimum, type set power min. Or, to set the output power to one quarter, type set power quarter. When the command is entered, the system displays the new power setting automatically. However, if you need to verify the output power setting for any radio, use the command get power. The following graphic shows the output power for a radio being changed from full to one quarter. 32 OWS Field Installation OWS Field Installation Appendix II: Installing the Band Pass Filter The band pass filter must be installed as close to the OWS enclosure as possible. The following graphic shows the filter installed on the OWS at its preferred location (connected directly to the antenna connector on the enclosure). Antenna Pole OWS Enclosure Antenna Cable Band Pass Filter OWS Field Installation 33 OWS Field Installation 34 OWS Field Installation OWS Field Installation Index FCC notice ii Federal Aviation Administration 1 filter 33 AC power 30 adapter 12, 13 airplanes use in 1 antenna directional 14 antenna adapter 13 antennas cable routing 23 directional 14 installing 8 omni 12, 19 placement 2 routing cables 23 sectored 16 type 2 gasket seal 29 ground termination 24 grounding 24 band pass filter installing 33 building codes 2 building materials 2 CAT5 28 CAT5 cable 28 contact information i continuity check 29 copyright notice i, ii coupling 29 data rates 2 DC power 30 directional antenna 8, 14 adjusting 15 enclosure 3 enclsure grounding 24 environmental limits 1 Ethernet cable 28 European Community (EC) conformity ii explosive device proximity iii FAA 1 OWS Field Installation hazardous locations 1 hospitals use in 1 Industry Canada notice ii limited warranty v local guidelines 2 maximum power settings 9 mounting 3 brackets 3 on a vertical pole 3 on a wall 7 NEC code 2, 24, 28 non-modification statement iii notices ii European Community (EC) ii FCC ii Industry Canada ii VCCI ii obstructions 2 omni antenna 8, 12, 19 output power setting 32 over-current protection 30 OWS 2400 1 OWS 3600 1 OWS enclosure 3 grounding 24 physical environment 2 planning the installation 2 planning your installation 2 pole 3 35 OWS Field Installation power settings 9 power source 2 powering up 30 product specifications 31 RF exposure iii RJ45 plug assembly 29 safety information 1 safety warnings iii sectored antenna 16 setting the transmit power 32 site survey 2 site surveys 2 solar shield iv specifications 31 straps 3, 6 Strix contact information i survey 2 table of contents vii theory of operation 1 transmit power 32 u-bolts 3, 4 VCCI notice ii vertical mounting brackets 3 vertical pole 3 warnings iii antenna placement iv electrical power iii general safety iii grounding the unit iv lightning activity iii warranty v 36 OWS Field Installation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 44 Page Mode : UseOutlines Page Layout : SinglePage XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:32698a85-577d-4f6b-9ef3-7f7c33421f74 Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2006:04:13 10:57:41Z Creator Tool : FrameMaker 6.0 Modify Date : 2006:04:13 12:08:49-07:00 Metadata Date : 2006:04:13 12:08:49-07:00 Document ID : uuid:f30b85ab-cd27-467e-8203-a82bc82630ad Format : application/pdf Title : ows_hardware_installation_manual.book Creator : Bill Wareing Author : Bill WareingEXIF Metadata provided by EXIF.tools