Stryker Instruments 0703001820 RFID Module User Manual
Stryker Instruments RFID Module
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2876321 |
| Application ID | pd/gqQ2y66h8EIomQLf3IA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 8.88kB (110954 bits) |
| Date Submitted | 2016-01-18 00:00:00 |
| Date Available | 2016-01-19 00:00:00 |
| Creation Date | 2016-01-15 16:04:11 |
| Producing Software | Adobe PDF Library 10.0 |
| Document Lastmod | 2016-01-15 16:04:14 |
| Document Title | User Manual |
| Document Creator | Acrobat PDFMaker 10.1 for Word |
| Document Author: | Rocque, Glen |
User’s Guide Manifold Receptacle (MR) Printed Circuit Board Assembly (PCBA) Stryker PN: 0703-001-820 Document Rev: 1.1 REVISION HISTORY REVISION COMMENTS DATE AUTHOR 0.1 INITIAL CREATION. 10/11/2015 G. R OCQUE 1.0 U PDATED FROM DESIGN REVIEW 10/14/2015 G. R OCQUE 1.1 U PDATED FROM N EMKO TCB COMMENTS 12/2/2015 G. R OCQUE Description: The Manifold Receptacle (MR) Printed Circuit Board Assembly (PCBA) is a custom designed circuit board intended to operate only within the Neptune 3 Rover and next generation of Neptune product line. The MR PCBA is made up of a custom mother board, Stryker PN 0590-085-340, an off the shelf RFID Reader daughter card, Stryker PN 0703-001-821, and an integrated antenna. Together, the mother board, the off the shelf RFID Reader daughter card, and integrated antenna constitute the Stryker MR PCBA, Stryker PN 0703-001-820. The mother board is manufactured by Stryker while the off the shelf RFID Reader daughter card is manufactured by Feig Electronics, PN 4320.000.00. Features: The MR PCBA is made up of an RFID interface circuit to communicate with the RFID Reader daughter card, an illumination circuit for the manifold receptacle, a manifold detection circuit, a DC to DC power supply, a sprinkler controller circuit, a canister illumination driver circuit, and a UART interface bus to communicate with the Rover Main Controller (RMC) PCBA. All of the MR PCBA features are custom to the Neptune 3 Rover system. The MR PCBA cannot operate on its own and is a slave sub-system within the Neptune 3 Rover system. A set of proprietary commands exist between the RMC PCBA and the MR PCBA to configure, perform execution of tasks, and transfer data upon command. The proprietary commands always originate from the master RMC PCBA and are responded to by the slave MR PCBA. Page 1 of 3 Finally, the MR PCBA contains an integrated RFID antenna designed to read passive HF RFID smart tags. The integrated RFID antenna is located on the mother board, Stryker PN 0590-085-340. Technical Data: Mechanical Data: Housing: None provide, bare PCBAs only; installed within the Neptune 3 Rover Dimensions: (W x H x D): 3.31inch x 0.62inch x 4.82inch (84.07mm x 15.75mm x 122.43mm) Pwr/Comm Connector: 12 Pin-Connector, Samtec, IPL1-106-01-L-D-RA-K, custom wire configuration Weight: 2.7 oz. (77g) Electrical Data: Supply Voltage: 17 V DC to 41.2 V DC Current Draw: 1.0A Max at 36 V DC Roving Mode or 0.5A Max at 18 V DC Docking Mode Power Consumption: 36W Roving Mode or 9W Docker Mode Interfaces: RS485 – Level, 115.2 kbps, Proprietary Communication Protocol Processor: Microchip dsPIC 33EP256MU810 and Fujitsu MB90F562B Main RFID Functional Properties: Reader: Ability to detect, read, and write to passive HF RFID smart tags Operating Frequency: 13.56 MHz Distance: Short communication range, 1.5” or less Ambient Conditions: Temperature Range: 0°C - 70°C Humidity: 5 – 95% non-condensing Page 2 of 3 Federal Communications Commission (FCC) Statement Concerning Radio Frequency Interference: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Page 3 of 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Rocque, Glen Create Date : 2016:01:15 16:04:11-05:00 Modify Date : 2016:01:15 16:04:14-05:00 Subject : Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2016:01:15 16:04:14-05:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:edb1c0af-4a2e-45eb-95b0-ab2ae59ad1ad Instance ID : uuid:06da3545-b769-44c6-bed6-2e59e5f68aea Format : application/pdf Title : Description : Creator : Rocque, Glen Producer : Adobe PDF Library 10.0 Keywords : Source Modified : D:20151204155804 Company : Stryker Corporation Comments : Page Layout : OneColumn Page Count : 3EXIF Metadata provided by EXIF.tools