Summer Infant 02160T Dual Video Monitor with Scan User Manual 02160 IB Monitor 1 8 ai

Summer Infant, Inc. Dual Video Monitor with Scan 02160 IB Monitor 1 8 ai

users manual

Download: Summer Infant 02160T Dual Video Monitor with Scan User Manual 02160 IB Monitor 1 8 ai
Mirror Download [FCC.gov]Summer Infant 02160T Dual Video Monitor with Scan User Manual 02160 IB Monitor 1 8 ai
Document ID612991
Application IDlJJbkgrmCs/z87OB4shUVA==
Document Descriptionusers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize130.08kB (1626029 bits)
Date Submitted2005-12-19 00:00:00
Date Available2005-12-17 00:00:00
Creation Date2005-10-14 12:28:07
Producing SoftwareAcrobat Distiller 6.0.1 for Macintosh
Document Lastmod2005-10-14 15:04:01
Document Title02160-IB-Monitor-1-8.ai
Document CreatorAdobe Illustrator(R) 11
Document Author: WAlter Petrosky

FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the Parent’s Unit
- Increase the separation between the equipment and the receiver
- Consult the dealer or an experienced radio/TV technician for help
/\"f
visit us at
www.s||mmerinlunttcom
Feel free to contact us at the below phone number or email lf you should need to
order replacement or additional products.
We at Summer Infant stand behind all of our products If you are not completely
satlsiled or have any questlons, please Contact our Customer Servlce Department
at 1—800—26876237 or email us at customerservice®summerinfant com
Summer Infant Europe, m).
20 Sparrows Heme
Bushey, Hertfordshrre
won in UK
44 (mm mm 4419
a 2005 Summer Infant, Inc
Colors and styles may vary
MADE IN CHINA,
Please retain lnIormatlon tor
future reference
Summer Inturrt. Inc.
551 Great Road
PO Box 829
Slatersvllle, RI 028767089? USA
t-eon-Zéa-6257
was
02 1 6 0
Please read the following instructions
and warnings carefully
Keep this instruction manual
for future reference
Tools requlred:
Phllllps head screwdriver (not included),
For Technical Support Call 1-800-268-6237 or
E-Mail at customerservice@summerinfant.com
For use with children from birth and up.
AWARNING:
Adult assembly required.
Keep small pans away from
chlldren when assembling.
INSTRUCTION MANUAL
DAY AND NIGHT
DUAI. SCANNING VIDEO MONITOR
Thank you for buying the 2.4 GHz Day and Night Dual Scanning
Video Monitor from Summer Infant. This unit includes two cameras;
great for two children, twins, or two rooms in the housel With the
all-new scan feature you now have the option to scan one room
individually or scan two rooms for 8 second intervals. As your family
grows, on additional camera may be purchased separately and
added to this unit for a three room monitoring system.
ACAUTION:
KEEP SMALL PARTS OUT OF CHILD‘S REACH.
See page 8 (back page) for contact information if you should need to order
replacement or addltonal products.
QUICK SET UP:
SPECIAL FEATURES (continued):
Read the instruction manual for more detailed
instructions and explanations.
- Place Camera in nursery and position lacing crib
(do not place in crib or within child's reach).
Tilt the Multi—Position Camera/Microphone so it is
facing baby as much as possible (Figure A).
Use Security Clips included to secure Camera’s
O'
- t
cord away from baby‘s reach (Figure B). Camera
may also be attached to a wall using wall anchor
and screw (included). (Figure C)
- Plug small AC Adapter into Camera's AC
Adapter Jack and other end of cord into
a standard electrical outlet.
- Turn Camera on and select channel by setting
the Channel Selector (Off/NB/C) to channel A.
- Multi-Positian Camera/Microphone: The Camera/ Microphone
should be positioned so it is facing baby as much as possible. Be sure
not to place camera in crib or within arm’s reach of baby. This
multi-position feature is unique to Summer Infant nursery monitors.
It allows the microphone to focus on baby’s voice while filtering out
other household noises.
- Channel Scan: Three channels and scanning feature allows parents to
view two different locations, with the option of selecting channels that
mimimize interference, and scanning between the two camera. The
Scan function allows the parents to view each location a camera is set
up (up to three locations) for 8 second intervals.
' Position TV in the room from which you will monitor
12
baby. Plug large AC Adapter into TV's AC Adapter .
Jack and plug the other end into a standard
electrical outlet. , \
- Turn TV on using Power OnNolume Dial.
Set Channel Selector (A/B/C/Scan) to channel A.
You should now be able to see a view of the
nursery and hear any sounds in the nursery.
If you don’t get a picture, press the
Quick ViewNideo On/Off Button.
- If the picture is not clear, try switching both the Camera and the TV to
channel B or channel C. Sometimes a slight adjustment to the Camera
or TV can make a significant difference in reception.
' Adjust the volume on the TV as needed.
- To use the second camera, set it up in another location, and ensure that
the Channel Selector is set to channel B or C.
- To use the scanning function of this Monitor, set channel selector on
SCAN. The TV will scan each active channel for 8 seconds.
PROBLEM SOLVING:
No picture or sound on TV
- Make sure the TV is turned on
- Make sure the AC Adapters are plugged in
- Make sure the outlets are working
' Make sure the two Cameras are set on different channels. Toggle the TV
between one or the other channel (try using the third channel to minimize
interference if necessary)
Sound but no picture on TV
- Press the Quick ViewN|deo On/Off Button once to turn on v|deo mode
- Try adjusting the Brightness, Contrast and Vertical Hold dials on the TV
' Test reception by moving the TV and/or Camera to different locations
- Make sure the two Cameras are set on different channels. Toggle the TV
between one or the other channel (try using the third channel to minimize
interference if necessary)
P|clure but no sound
- Turn up the volume on the TV using the Volume Dial
' Make sure the two Cameras are set on different channels. Toggle the TV
between one or the other channel (try using the third channel to minimize
interference if necessary)
Picture not clear
- Make sure the two Cameras are set on d|fferent channels. Toggle the TV
between one or the other channel (try using the third channel to minimize
interference if necessary)
- Position the TV closer to the camera if necessary
- Move TV away from other monitors, cordless phones, walk-talkies, etc.
- Try ad)usting the Brightness, Contrast and Vertical Hold Dials on the TV
- Test recept|on by movlng the TV and/or Camera to dlfierent locat|ons
Squealing sound
- Move the Camera and the TV further away from each other
it you experience o problem that Is not noted in this monuut. please do not return the product
to the store. Our Customer Service Department may have a simple solution to your prootem,
Please contact us 1-100-255-5137 or e-moit us at customerservlce@summerinhnl.cnm.
SET UP 8: USE (continued):
Testing Your Initial Setup (continued):
To test reception you will need two adults. One adult should view the
picture on the TV while the other is in the nursery to adjust the Camera.
Often the quality 01 the reception can be improved by slightly
repositioning the Camera, TV, or both. It may help to place a stutfed
animal or doll in the crib to simulate the position and size 01 your baby.
Adjust the picture quality on the TV as needed by using the Contrast,
Brightness and Vertical Hold Dials.
To test sound quality, have one adult speak in both a normal tone and a
whisper near the crib. Adjust volume on the TV's Volume Dial as needed.
TIPS FOR
IMPROVING RECEPTION:
- Change the channel on both the TV and the Camera. Always make sure
they are set to the same channel (both on A, both on B or both on C).
Always make sure that each camera is on a different channel (Le. one
on Channel A, one on Channel B).
- Position the TV closer to the Camera if necessary,
- Move TV away from other monitors, cordless phones, walk-talkies, etc.;
even slightly moving the parent’s unit could greatly improve reception.
- If you hear feedback or squealing noise, move the Camera and the TV
further away from each other.
SPECIAL FEATURES:
' Sound lights: The 5 Sound Lights will illuminate on the TV depending on
the level at your baby's sounds. For example, if your child is just caoing,
only one or two lights will illuminate, If your baby is crying, several will
illuminate, depending on how loud she is crying. This feature is
particularly helpful if you are in a noisy room.
' Ouick ViewNideo OnlOII Button: This button turns the video mode on.
It you only want to hear your baby, press the Quick ViewNideo On/Ofl
Button again to shut olf the video. The Quick ViewNideo On/Olf Button is
ideal for easily turning on the video option in the middle 01 the night.
- Night Vision: In a darkened room the monitor will automatically use its
inIrared LED’s to transmit a clear image 01 baby, so you can see your
child at night!
AWARNING:
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION.
- Prevent cord entanglement — do not place Camera in crib or within
arm's reach of baby. Use enclosed Security Clips to help secure cords
away from baby's reach. Never use extension cords with AC adapters.
Only use the AC Adapters provided.
0 When an AC Adapter is plugged into an electrical outlet, do not touch
the exposed end.
- Do not use monitor near water (such as bathtub, sink, etc).
- Keep monitor away from heat sources (such as stoves, radiators, etc)
and make sure there is proper ventilation (not on sofas, cushions,
beds, etc which may block ventilation).
- Nursery monitors use public ainlvaves to transmit signals. This monitor
may pick up signals from other monitors or similar devices and signals
broadcast by this monitor may be picked up by other receivers.
- This product is not a toy. Do not allow children to play with it.
- This product contains small parts. Adult assembly required.
Exercise care when unpacking and assembling the product.
FEATURES St COMPONENTS
(for monitor):
Quick View/Video rv
On/Ott Button (BACK VIEW):
W, (Vldeo/On/Oii)
—Carrving
/\ Handle
‘ltl 1 “In Contrast
H' . t 0nl ,, ., _ .
,. u , Mum . , [1— Brightness
g/ i Dlul _. .—— Vertical
Channel
Selector ’\ f V "dd
(A/B/C/ ' Speaker Ac Adapter Jack
SCAN) ' ' TV Ac Adapter
(large) |
”W" Sound Lights .-| g
On LED
Video on light
— w
FEATURES & COMPONENTS
(for camera):
Security Clips
(SIX)
Camera
AC Adapter
(small)
Wall Anchor (one)
Screw (one) ‘
Cameras (two):
Nighttime
LED's
(lardarkened
room)
_- Camera/Microphone
c L Channel Switch (Off/NB/C)
Ac Adapter Jack (bottom ol unit)
SET UP & USE:
CAMERA
Step 1:
Table Top or Wall Mounting:
Tilt Camera/Microphone up, and pull up (Figure A).
Determine a location for the Camera that will provide
the best view of your baby in his crib. Place the Camera
on a flat surface, such as a dresser, bureau, or shelf. Or
mount the Camera on a wall. Be sure not to place camera in crib or within
arm’s reach of baby. Be sure to test reception and Camera positioning
before mounting to a wall (see "Testing Your Initial Set Up" section).
To Wall Mount:
a) Pre-drill a hole in the wall (3/16", 4.8mm, drill bit).
(Figure B).
b) Insert the wall anchor (included) into the hole
and with a hammer, tap gently on the end until
the wall anchor is flush with the wall.
c) Insert the screw (included) into the wall anchor
and tighten screw until only 1/4“ (6.2mm) of
the screw is exposed.
d) Insert smaller AC Adapter into the Camera’s
AC Adapter Jack.
e) Slide the back of the Camera down onto the screw
until the Camera is secure to the wall.
1) Plug the AC Adapter into a standard electrical outlet.
9) Secure the cord to the wall using the 6 Security Clips
included to keep cord away from baby's reach
4 (Figure C).
SET UP 8: USE (continued):
To Adjust Camera:
Place camera on a hard, well ventilated surface approximately 4 — 6 feet
lrom the child or viewing object. Pivot camera lens upward until it is
standing upright in the base. For additional height gently pull the camera
lens up until you hear a click. For full extension, gently pull it up again until
you hear another click. Adjust camera byturning left to right 180 degrees
and tilting forward or backward for optimal viewing positions.
Step 2: Set Channel Selector (OFF/A/B/C) to channel A. The Power On LED
will illuminate solid green.
Step 3: Repeat for second Camera in another location, set to channel
B or C.
TV
Step 1: Position TV in the room from which you will monitor your baby in
the other location.
Step 2: Plug the larger AC Adapter into the TV’s AC Adapter Jack. Plug the
other end into a standard electrical outlet.
Step 3: Turn the TV on using the OnNolume Dial. The Power On LED will
illuminate green. Set the Channel Selector (A/B/C/Scan) to desired channel
or to the Scan channel to see each location for 8 second intervals. Press
the Quick ViewNideo On/Otf Button (labeled "Video On/Off") once for a
view at the nursery. When video mode is on, the Video On Light will
illuminate green.
Step 4: Adjust the volume as needed using the Volume Dial. Adjust picture
using the Contrast, Brightness, and Vertical Hold Dials on the back of the TV.
Step 5: For audio and no video, press the Quick ViewNideo On/Oft Button
again to shut off the video mode.
Step 6: To turn the TV off completely, use the OnNolume Dial.
Testing Your Initial Setup:
Be sure to test your monitor’s reception before initial use. We also
recommend testing your monitor’s reception periodically. Please keep in
mind that the Day and Night Dual Scanning Video Monitor set will not
provide the same level of picture quality as your television with cable,
satellite dish, ordigital service. 5

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:496f3bce-3ce5-11da-96a8-003065c901f8
Producer                        : Acrobat Distiller 6.0.1 for Macintosh
Modify Date                     : 2005:10:14 15:04:01-04:00
Creator Tool                    : Adobe Illustrator(R) 11
Create Date                     : 2005:10:14 12:28:07-04:00
Metadata Date                   : 2005:10:14 15:04:01-04:00
Document ID                     : uuid:866acc33-3ccf-11da-b355-003065c901f8
Format                          : application/pdf
Creator                         : WAlter Petrosky
Title                           : 02160-IB-Monitor-1-8.ai
Author                          : WAlter Petrosky
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PZK02160T

Navigation menu