Summer Infant 28030T Best View digital color video monitor User Manual 28030 35 Monitor IB 10 20 10erN

Download:
Mirror Download [FCC.gov]
Document ID	1385684
Application ID	cPYysVU/6/wv05shgZ3nOw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	300.37kB (3754636 bits)
Date Submitted	2010-12-03 00:00:00
Date Available	2010-12-25 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Corel PDF Engine Version 3.0.0.667
Document Lastmod	0000-00-00 00:00:00
Document Title	28030_35 Monitor IB 10-20-10erN
Document Creator	CorelDRAW
Document Author:	cattac

II you experience a problem that is not noted in this manual.
please do not return the product to the store Our Customer
Servtce Department may have a simple solu onto your problem,
Please Contact us at 1-800-268-6257 or emall us ot
customerservice@summe Iant.colrl.
FCC InIormotion
This device complies with part 15 oi the FCC Rules Operation is subiect to
the lollowmg two conditions: (i ) This device may not cause harmlui
interlererlce,
and (2) this device must accept any interierence received, including
interlerence that may cause undesired operation
CAUTION: Changes or modiiications not expressly approved by Summer
infant may void the users authority to operate this equipment
NOTE: This equipment has been tested and lound to comply with the limits
lor a Class B digital device, pursuant to part is oi the FCC Rules. These
llmlts are designed to provide reasonable protection against harrnlui
interlerence in a residential installation This equipment generates, uses
and can radiate radio lreauency energy and, ii not installed and used in
accordance with the instructions, may cause harmlul lnterlerence to radio
communications. However, there is no guarantee that interierence will not
occur in a particular installation it this equipment does cause harmiul
interlerence to radio or television reception, which can be determined by
turning the equlpment oii and on, the user is encouraged to try to correct
the interierence by one or more at the lollowmg measures
- Reorlent or relocale the receiver
- increase the separation between the equipment and the receiver
~ Connect the equipment into an outlet on a circuit dillerent lrorn that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician lor help
CAUTION 1 To comply with FCC RF exposure compliance requirements, a
separatlon dlstunce ol at least 20 cm must be malntained between the
antenna ol this device and all persons. 1. This transmitter must not be
co—Iocated or operating in conjunction with any other antenna or
transmiller
summer lnlant, lnc. Monitor Warranty Policy
Summer lniant, lnc. will repair or replace (at our opllarl) your unit lree oi
charge tor 12 months lrorn the date or purchase lI the unit is delective in
workmanship or materials To claim your repair/replacement, the product
must be returned to Summer inlant along wlth a copy or the original
purchase receipt. in the absence or the purchase receipt, the warranty will
be lz months lrorn the date ol manufacture This warranty does not apply to
normal wear or damage lrom misuse, abuse, improper storage and
handling, installation, accident, unauthorized repair or alteration Please
contact our Customer Service Department by phone at lesuuezeaeom
or via email at customerservice@summerinlont com ior details,
We LOVE our" (ustomersl
/ Get to know us at:
www.summe fant.com
We at Summer intent stand behind all or our products. it
you are not completely Sallsfled or have any questions,
please contact our customer service department at
lesocezssesm or tustomerservice@summerinrent.tom
(For Europe call 744 (was 420 4429 or
tustomerserviceuk@$ummerinfarltxomj
Summer lnlant, Inc.
l275 Park East Drive
Woonsocitet, El 01395 USA
landzodozn
12
summer lnlant Europe, in).
cilice Suite 6, Second Floor
Bournehall House, Bourneholl Road
Bushey, Herllordshire wnzs SHP UK
+44 (u) 203 no 4429
© ZUlfl Summer lnlant, Irlc
Colors and styles may vary
Please retain lnlormalion
lorlulure relererlce
MADE IN CHINA, lfl/lU
408-000647-00
25030/28035
Please read the
following instructions
and warnings carefully.
Keep this instruction manual
for luture reference.
Tools required:
screwdriver (not included)
For technical support see back page.
For use with children from birth and up
AWARNING:
Adult assembly required.
Keep small parts away from
children when assembling
INSTRUCTION MANUAL
BEST VIEW'" DIGITAL COLOR
VIDEO MONITOR
ACAUTION:
KEEP SMALL PARTS OUT OF CHILD‘S REACH.
AWARNING:
THIS PRODUCT CANNOT REPLACE RESPONSIBLE
ADULT SUPERVISION.
- Prevent cord entanglement — do not place Camera in crib
or within arm’s reach of the baby. Use enclosed Security
Clips to help secure cords away from baby's reach.
Never use extension cords with AC adapters. Only use
the AC Adapters provided.
- When an AC Adapter is plugged into an electrical outlet,
do not touch the exposed end.
0 Test monitor before first use, periodically, and when
changing location of the Camera.
0 Do not use monitor near water (such as bathtub, sink, etc.).
0 Keep monitor away from heat sources (such as stoves,
radiators, etc.).
0 Make sure there is proper ventilation around all monitor
components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.
- Nursery monitors use public airwaves to transmit signals.
This monitor may pick up signals from other monitors or
similar devices and signals broadcast by this monitor may
be picked up by other receivers.
t This product is not a toy. Do not allow children to play with it.
- This product contains small parts. Adult assembly required.
Exercise care when unpacking and assembling the product.
A BATTERY WARNING:
0 Use only the original rechargeable batteries
provided. Please contact Summer Infant, Inc. for
replacement batteries. Contact information can be
found on page 12 of these instructions or on the
battery itself.
0 Do not mix old and new batteries.
- Do not mix alkaline, standard,
or rechargeable batteries.
0 Batteries are to be inserted with correct polarity.
- Clean battery and product contacts prior to
battery installation.
IMPORTANT SAFETY INSTRUCTIONS
11) Power Lines- An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits as contact with them
might be fatal.
12) Overloading- Do not overload wall outlets, extension cords. or integral
convenience receptacles as this can result in a risk of fire or electric
shock.
13) Object and Liquid Entry- Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
14) Servicing- Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
15) Damage Requiring Service- Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled. or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjusting only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to it’s normal operation,
e) If the product has been dropped or damaged in any way. and
0 When the product exhibits a distinct change in performance-
this indicates a need for service.
16) Replacement Parts- When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufac-
turer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
17) Safety Check- Upon completion of any service or repairs to the product,
ask the service technician to perform safety checks to determine that the
product is in proper operating condition.
18) Wall or Ceiling Mounting- The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
19) Heat- The product should be situated away from heat sources such as
radiators, heat registers, stoves. or other products (including amplifiers)
that produce heat.
11
CAUTION
RlSK or ELECTRlC SH
A A
Do NOT ExPosE To RAIN on MOISTURE
IMPORTANT SAFETY INSTRUCTIONS
1) Read Instructions- All the safety and operating instructions should be
read before the product is operated.
2) Retain Instructions- The safety and operating instructions should be
retained for future reference.
3) Heed Warnings- All warnings on the product and in the operating
instructions should be adhered to.
4) Follow Instructions- All operating and use instructions should be
followed.
5) Cleaning- Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6)At‘tachments- Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7) Water and Moisture- Do not use this product near water- for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
5) Accessories- Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury to a child or
adult, and serious damage to the product. Use only with a cart. stand,
tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow the manufacturer‘s
instructions, and should use a mounting accessory recommended by the
manufacturer.
9) Power Sources- This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power. or other
sources, refer to the operating instructions.
to) Power-Cord Protection- Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them. paying particular attention to cords at plugs. convenience
receptacles, and the point where they exit from the product.
10
A BATTERY WARNING:
(continued)
- Do not short-circuit supply terminals.
- Only the recommended batteries or equivalent are
to be used, volts and size.
- Remove batteries when product is stored for long
periods of time or when batteries are exhausted.
0 Dispose of exhausted batteries properly.
- Do not recharge non-rechargeable batteries.
- Rechargeable batteries are only to be charged
under adult supervision.
- Keep all batteries away from children.
FEATURES 8: COMPONENTS
(for monitor):
Mounom
Monitor
(Book View):
am View] 7
we» Onlolf . a
left Clip/
rower/Menu fig“? Adivstoble
Iiefllery llle/ . Kickttund
on
ren on ro
Indlcglnrs ' PM"
ampunmenr
Comm/Manu- om"... AN Out—— At: Aduplcr
Control Panel Jack Jack
Em"
Door Screw
Camera lam View):
Camera . , ,,
Speaker
CAMERA:
—Nighttime tED':
(for darkened room)
- Microphone
—Power on [ED
Pow-r 0n/—. a
on Switch
A: Adopter luck—
AC Adapter (2) AV Cable
11
Woll Anenor
— (one)
, SecurityClips
\ (six)
Screw (one) 3
SET UP 8: USE:
PROBLEM SOLVING:
CAMERA
Table Top or Wall Mounting:
Determine a location lor the Camera that will provide
the best view of your baby in his crib. Place the Camera on
a (lot surface, such as a dresser, bureau, or shelf. Or mount
the Camera on a wall. CAUTION: BE SURE NOT TO PLACE
CAMERA IN CRIB OR WITHIN ARM'S REACH OF BABY. Do
not place the Camera neor open windows, direct sunlight or
heat sources. Be sure to test reception and Camera
oning belore mounting to a wall (see "Testing Your
In aI Set Up" section).
To Wall Mount:
1) Pre-drill a hole in the wall
(3/16“, 4.8mm, drill bit) (Figure A).
2) Insert the wall anchor (included)
into the hole and with a hammer,
tap gently on the end until the wall
anchor is flush with the wall.
3) Insert the screw (included) into the
wall anchor and tighten screw until
only 1/4“ (6.2mm) ofthe screw
is exposed,
4) Insert AC Adapter into the Camera’s
AC Adapter Jack.
5) Slide the back of the Camera down onto the screw until
the Camera is secure to the wall.
6) Plug the AC Adapter into a standard electrical outlet.
7) Secure the cord to the wall using the 6 Security Clips
included to keep cord away from baby‘s reach (Figure B).
6) Slide switch on side of Camera to ON and the
POWER ON LED will illuminate solid green.
MONITOR
To Use in Video and Audio Mode:
Step 1: Place the Monitor in the room from which you want to monitor
your baby (re. bedroom or livrng room). Plug an AC Adapter into the
AC Adapter Jack and the other end into a standard electrical outlet,
top at the unit.
No picture or sound on Monitor
- Make sure the Monitor is turned on
- Make sure the AC Adapters are plugged in
' Make sure the outlets are working
~ Make sure Monitor and Camera are SYNCHED up.
(refer to “Synching MONITOR and CAMERA” section on
page 7)
Sound but no picture on Monitor
v Press the Quick ViewNideo On/Off Button once to turn on
video mode
- Try adjusting the Brightness Control on the Monitor
- Test reception by moving the Monitor and/or CAMERA to
different locations
Picture but no sound
~ Turn up the volume on the Monitor using the Volume Control
Picture not clear
- Position the Monitor closer to the CAMERA if necessary
. Move Monitor away from other monitors, cordless phones,
walkie-talkies, etc.
- Try adjusting the Brightness Control on the Monitor
- Test reception by moving the Monitor and/or CAMERA to
different locations
Sauealing sound
' Move the CAMERA and the Monitor lurther away from
each other
TIPS FOR IMPROVING RECEPTION:
- Position the Monitor closer to the CAMERA if necessary.
- Move Monitor away from other monitors, cordless phones,
walkie—talkies, etc.; moving even slightly could greatly
improve reception.
- If you hear a feedback or squealing noise, move the
CAMERA and the Monitor further away from each other.
~ NOTE: DO NOT MOVE THE CAMERA BY HAND AS IT MAY
DAMAGE INTERNAL MOTOR PARTS.
SPECIAL FEATURES:
~ Video Sleep Mode: While operating on battery power, the
video screen will go to sleep, to conserve battery power. Audio
and sound lights will function normally. Press the Video On/Oll
to resume viewing. This option is NOT available when using AC
adapter.
' Sound Lights: The 5 Sound Lights will illuminate on the Monitor
depending on the level at your baby's sounds. For example, it
your child is just cooing, only one or two lights will illuminate. It
your baby is crying, several will illuminate, depending on how
loud she is crying. This leature is particularly helpful if you are
in a noisy room.
~ Quick ViewNideo OnIOll Button: This button turns the video
mode on. ll you only want to hear your baby, press the Quick
ViewNideo On/Oll Button again to shut all the video. The
Quick View/Video Orr/Oil Button is ideal lor easily turning on
the video option in the middle of the night.
- Night Vision: In a darkened room, the Monitor will
automatically use its inlrared LED's to transmit a clear image of
baby, so you can see your child at night!
- Multi-Position Camera/Microphone: The
Camera/Microphone should be positioned so it is lacing baby
as much as possible. This multirposition leature is unique to
Summer Infant nursery monitors. It allows the microphone to
focus on baby’s voice while filtering out other household
noises.
' A/V Cable: To view video through your TV, plug the AN cable
jack connection into monitor and connect the other ends into
the corresponding color coded parts on your TV. Scroll through
AN inputs on your television’s menu until monitor picture is
visible.
Note: The Monitor's power button must be turned ON and CAM
pro—selected before connecting the AN cable. Once the AN cable is
connected the Monitor's controls cannot be activated.
For best results use on a 27" TV or smaller.
SET UP & USE (continued):
Step 2: Press and hold down "POWERO" button to turn on until
Video or Summer logo appears on screen
Step 3: For audio and no video, press the VIDEO ON/OFF button on
top of the unit.
Step 4: To turn the monitor oli completely press and hold the
”POWERO" button for 3 seconds.
MONITOR MENU mode:
Step 1: Press ”MENU" button to enterthe MENU mode. Press
again to leave the MENU mode.
MAIN MENU item:
BRTIGHTNESS — move up and down buttons on Camera/Menu
Control Panel to adjust brightness
Reler to Adding Additional Camera section tor other menu
functions.
MONITOR REMOTE CONTROL FUNCTIONS
The Monitor can control the movement ol the CAMERA.
The camera head has the ability to rotate up, down, right,
Ielt and zoom.
Step 1: Press the left or right buttons on Camera/Menu
control panel to move the camera Ielt or to the right.
Step 2: Press the up or down buttons on Camera/Menu
control panel to move the camera up or down.
Step 3: Press the OK/Zoom button on Camera/Menu control
panel once lor a 2X zoom of image on Monitor and press
again to change back to normal View.
ADDING ADDITIONAL CAMERA:
Note: This product can accept up to tour cameras. To order on
additional camera (#28074), please contact our Customer
SerVice Department by phone at 1—800726876237 or via email at
customerservice@summerintant.com for details. (For Europe Call
+44 (0)208 420 4429 or customerserviceuk@summerinlant.com)
Please Note: The SCAN, DEL CAM, ADD CAM and VIEW CAM menu
options are only used with additional cameras.
SET UP 8: USE (continued):
SET UP & USE (continued):
Testing Your Initial Setup:
Be sure to test your Monitor's reception betore initial use.
We also recommend testing your Monitor's reception periodically
Please keep in mind that the Best Viewm Digital Color Video Monitor
will not provide the same level 01 picture quality as your television
with cable, satellite dish, or digital service.
To test reception you Will need two adults. One adult should view the
picture on the Monitor while the other is in the nursery to adiust the
Camera. Often the quality of the reception can be improved by
slightly repositioning the Camera, Monitor, or both. It may help to
place a stufted animal or doll in the crib to simulate the position and
size oi your baby. Adiust the picture quality on the Monitor as
needed by using the Brightness Adjustment within monitor menu
To test sound quality, have one adult speak in both a normal tone
and a whisper near the crib Adjust volume on the Monitor’s
Volume Adjustment as needed.
To Use the Video Monitor in Portable Mode:
For use in portable mode, the Monitor requires i 3.7V LITHIUM-iON
rechargeable battery (included).
Tips:
' Before using Monitor in portable mode (battery), be sure to
charge battery 12-i6 hours.
- To charge battery, plug the Monitor AC Adapter into the
Monitor’s AC Adapter Jack. Plug the other end into a standard
electrical outlet,
- Alter initial 12-i6 hour charge, to achieve optimal battery iite,
charge battery overnight and unplug all day during use.
' Note: Oniycharge battery when low indicator light comes on.
Constant recharging of your battery before low battery indicator
light comes on will decrease the life of your batteries.
- When battery is low, the Power On LED will illuminate amber,
indicating that the battery needs to be recharged.
' To conserve battery power, use AC Adapter whenever possible.
Remove battery during long periods at nonruse.
- If battery is exhausted, remove immediately lrom the Monitor.
- Properly dispose ot exhausted battery.
Battery Installation:
Note: This step is only needed it replacing battery.
1. Locate the battery compartment door on back oi monitor.
2. Remove battery door screw with flat head
screwdriver.
5. Remove battery door and battery.
4, insert new battery and replace battery door
(Figure C).
Belt Clip:
For convenience and portability, you can clip
the Monitor to your belt or waistband after a
battery has been installed (Figure D)
Footrest:
The Monitor has a built—in tootrest for tabletop
convenience. Simply flip out tootrest and place
the Monitor on a stable, Ievei surlace (Figure E).
Synching Monitor and CAMERA:
The Monitor and Camera are synched at the tactory
tor privacy reasons. It the Monitor and Camera are
not synching with each other for any reason, please
sync them as described below
Step 1: Move the Monitor to the same area as the
Camera. With both the Camera and Monitor on, press the "POWER”
button once and using Camera/Menu control panel scroll to the Right
and Up to “ADD CAM” Then press the OK/Zoom button.
Step 2: The Power LED flashes green and within 8 seconds, press the
“CODE" button once at the side of the camera.
Step 3: The Power LED on the camera Will flash and you should then
see a picture from the Camera on the Monitor.
Step 4: If this is unsuccesslul, you should repeat steps above making
surethe Camera and Monitor are close enough to each other for
synching.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
Creation Date--Text             : 
Mod Date--Text                  : 
Producer                        : Corel PDF Engine Version 3.0.0.667
Creator Tool                    : CorelDRAW
Modify Date                     : 2010:11:18 17:15:17+08:00
Create Date                     : 2010:11:03 14:11:54+08:00
Metadata Date                   : 2010:11:18 17:15:17+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 26396 bytes, use -b option to extract)
Format                          : application/pdf
Creator                         : cattac
Title                           : 28030_35 Monitor IB 10-20-10erN
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 234.950000
Max Page Size H                 : 234.950172
Max Page Size Unit              : Millimeters
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Group Name               : 預設色票群組
Swatch Group Type               : 0
Rendition Class                 : proof:pdf
Document ID                     : uuid:0218f20d-cf07-4177-b780-ad0308db921a
Instance ID                     : uuid:6a17438d-8bc1-4a61-8858-d2398717d923
Manifest Link Form              : EmbedByReference
Manifest Reference File Path    : C:\Documents and Settings\songjunhong\桌面\PB0302791111.jpg
Manifest Reference Instance ID  : uuid:18c5c8b8-e72e-11df-9e97-ab276e7a9060
Manifest Reference Document ID  : adobe:docid:photoshop:18c5c8b7-e72e-11df-9e97-ab276e7a9060
Page Count                      : 6
Container Version               : 11
Creator Version                 : 14
For                             : songjunhong,
Bounding Box                    : 0 0 657 657
Author                          : cattac
Image Height                    : 657
Image Width                     : 657
Image Size                      : 657x657
Megapixels                      : 0.432

EXIF Metadata provided by EXIF.tools