Sunitec Enterprise BH005 Bluetooth Headset User Manual UM BH695 sunitec EN 131209

Download:
Mirror Download [FCC.gov]
Document ID	2155791
Application ID	zDZwHwPXD+C5Q7VWqHkXUA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.6kB (232551 bits)
Date Submitted	2014-01-02 00:00:00
Date Available	2014-01-02 00:00:00
Creation Date	2013-12-26 15:38:32
Producing Software	Corel PDF Engine Version 15.0.0.486
Document Lastmod	2013-12-26 15:38:32
Document Title	UM-BH695-sunitec-EN-131209
Document Creator	CorelDRAW X5
Document Author:	Administrator

4. Charging the Battery
A. The first time, please charge the device for no less than 2 hours to make
sure the headset is fully charged and the battery reaches its full capacity.
B. Afterwards, each charge cycle may take around 2 hours.
C. The LED will light up in red while charging and turn off once the
charging is complete.
D. If you have not used the item for a few months, the LED might not
turn red when first charging. It may take a few minutes before the LED
turns red.
E. When the voltage of the battery goes down to 3.3V, the red LED will flash
every 10 seconds. When the voltage goes down to 3.0V, the headset will
power off automatically.
Note: It is suggested that you use only the charger provided. Do not use
chargers from any other devices as it might damage this earphone device.
BH695
Bluetooth Mono Headset
5. Turn ON / OFF
Turn ON: From OFF, press and hold the MFB for 3 seconds until the blue
LED fast flashes.
Turn OFF: From ON, press and hold the MFB for 3 seconds until the red
LED lights for 2 seconds.
6. Pairing Bluetooth Headset to Mobile Phone
Pairing is the process of connecting your headset with your mobile
phone. Before using the headset with your mobile phone, you must pair
both devices. If you wish to use your headset with a different mobile
phone, you must reinstate the pairing process with your intended
Bluetooth mobile phone.
A. Ensure the headset is off.
B. Switch to pairing mode by holding in the MFB button for 6 seconds
until the LED blinks blue and red alternately.
C. Turn on the mobile phone and place it within 1 meter of the headset.
D. Activate the Bluetooth function on your mobile phone and search for
the accessible Bluetooth device by referring to your mobile phone user
guide for details.
E. Select BT Headset from the list.
F. Enter the pre-programmed code 0000 and press OK to pair the
headset and the phone. When the pairing is completed, the blue and
red LED will stop flashing. The headset is under the standby mode when
the blue LED flashes every 10 seconds.
User Manual
1. About Bluetooth Technology
Bluetooth wireless technology is set to revolutionize the personal
connectivity. By providing freedom from wired connections-enabling
links and connectivity between mobile computers, mobile phones,
portable handheld devices and other Bluetooth enables devices within
10 meters. Utilizing global sound & digital data 2.4G ISM transmission, it
makes global communication in the way you've never dreamed of !
G. Press Return to go back to your mobile phone's main menu. Please
place the mobile phone and the headset within 10 meters sensing
distance. You should now be able to make and receive calls using
your headset.
Note: If the pairing cannot be completed within 2 minutes after the
pairing mode is activated, the headset will power off automatically.
Please repeat the steps above to pair the headset and mobile phone again.
Once paired and connected, the headset will be automatically connected
to your phone whenever you turn the headset on again.
2. Getting to know your Bluetooth Headset
To use your Bluetooth Headset, please follow these simple steps:
A. Charge your Headset prior to using the Headset, it is recommended to
charge the battery fully for the first time. Normal full charge time is 2
hrs. (approx.)
B. Place your Headset and a Bluetooth-enabled mobile phone within 1
meter for pairing.
NOTE: Ensure your Headset and mobile phone is placed within 10 meters
Bluetooth sensing distance. (Obstruction could cause shorter sensing
distance.)
7. Connection/Link between Headset and Mobile Phone
After the pairing is completed, the headset is always under standby mode.
Before you place or answer a call, if the headset icon is not shown on the
phone screen, please follow the steps below to activate the Bluetooth
connection/link through your mobile phone or headset until the pairing
headset icon is on the screen.
A. On the phone: Select the BT Headset from the paired list on your
phone screen.
B. On the headset: Turn on the headset again, and the headset will
connect the last paired device automatically.
3. Appearance and Function
8. Disconnection between Headset and Mobile Phone
When you need to connect your headset with another Bluetooth-enabled
mobile phone, please follow the steps below to disconnect the headset
with the pre-paired mobile phone.
A. Power off the Headset.
B. Select DISCONNECTING on the Bluetooth device list of your mobile
phone to remove the connection.
Note: When losing the connection/link, the headset will automatically
power off in 10 minutes.
1. Multi-Function Button (MFB)
2. Volume Up (V+)
3. Volume Down (V-)
4. LED Indicator
9. Using the Headset
5. Microphone
6. Charging Socket
7. Speaker
A. Answering Calls
When receiving a phone call, press the MFB button once to answer a call.
B. Ending Calls
Press the MFB button once to end a call.
C. Reject Calls
When receiving a phone call, press and hold the MFB button for 2
seconds to reject the call.
D. Voice-Dial
If your mobile handset is voice dialing enabled, under standby mode,
press the MFB button once and when you hear a beep, say the voice tag.
Note: Please make sure to record voice tag into the mobile handset
before using voice dialing function. This function is only applicable to
mobile handset with Bluetooth Hands-Free Profile. Functionality varies
depending on the mobile handset models you have. Please refer to your
mobile handset user guide for additional information.
E. Last Number Re-Dialing
Under standby mode, short press the MFB button twice for last
number redial.
F. Adjusting the Volume
During a call, press the V+ or V- button repeatedly until you reach
the desired volume level.
G. Mute & Unmute (During a Conversation)
1. Mute the microphone: Press and hold the V+ & V- button for 2 seconds.
2. Unmute the microphone: Press and hold the V+ & V- button for 2
seconds again.
H. Transferring Calls
1. Headset to Mobile Phone: During a call, short press the V+ & V- button
once. Then the call will be routed to your mobile phone.
2. Mobile Phone to Headset: Short press the V+ & V- button once to
route the call to the headset.
I. Reject the Second Call
During a call, short press MFB button for 2 seconds to reject the second
incoming call.
J. Hold the Call
During a call, short press the MFB button twice to hold the phone call.
Short press the MFB button twice again to resume conversation.
K. Answer the Second Call
1. During a conversation in progress, short press the MFB button once
to pick up the second call and end the first call.
2. During a conversation in progress, short press the MFB button twice
to pick up the second call and put the first call on hold.
L. Switch between 2 Phone Calls
During the two calls in progress, short press the MFB button twice to
swap calls.
15. LED Indication
Power off mode
Power on
Power off
Standby mode
Standby mode (disconnect
Bluetooth device)
Standby in low voltage
Talking in low voltage
Talking in progress
Pairing in progress
Mute
Charging in progress
Charging completed
Restore the default settings
LED off
Blue LED lights 5 times
Red LED lights 5 times
Blue LED flashes 1 time every 6 seconds
Blue LED flashes 3 times every 6 seconds
Red LED flashes 1 time every 6 seconds
Red LED flashes once every 10 seconds
Blue LED flashes once every 10 seconds
Red & Blue LED flash alternately
Blue LED flashes once every 10 seconds
Red LED stays on
Blue LED stays on
Red & Blue LED flash alternately
16. Product Specifications
Bluetooth Compatible Specifications: V3.0
Operating Frequency Band: 2.4GHz~2.48GHz unlicensed ISM Band
Output Power: Class 2 Power Output, up to 10 meters
Support Profiles: HSP, HFP1.5, A2DP Profiles
Support Multiple paired Device: Up to 8 Bluetooth Phone can be paired
Integrated with echo cancellation
Battery status display on phone(only support IOS device)
Battery: 61 mAh (rechargeable lithium polymer), 3.7V DC
Talk time: about 5 Hours
Music play time: about 4.5 Hours
Standby time: about 180 Hours
Charger time: about 2 Hours
Power Input Voltage: 5V
Operating temperature range: -20℃~ +45℃
Weight: 15.2g
10. Restore the Factory Default Settings
To restore your headset to its factory default setting, press and hold the V+
or V- button for 10 seconds until both blue and red LED flash alternately.
Then press the MFB button for 3 seconds to power off the headset to
complete the setting.
11. Care and Maintenance
A. Consider turning your headset off before placing it in your pocket or
bag. If the MFB is accidentally depressed, your mobile handset may
place an unintended call.
B. Do not expose the headset to liquid, moisture or humidity, as it is not
waterproof.
C. Do not use abrasive cleaning solvents to clean the headset.
D. Do not place the headset in high temperature, as it will result in an
explosion.
E. Keep headset away from sharp objects to prevent scratching
or damaging the device.
F. Do not stick anything inside the headset as this may damage internal
components.
G. Do not attempt to disassemble the headset, as it does not contain
serviceable components.
14. Safety Information
A. Check local laws regarding the use of a mobile handset and headset
while driving. If you use the headset while driving, be sure to focus on
safe driving practices.
B. Never allow children to play with the headset. Small parts may be a
choking hazard.
C. Observe all signs that require an electrical device or RF radio product
to be switched off in the designated areas. These could include
hospitals, blasting areas and potentially explosive atmospheres.
D. Turn off your headset prior to boarding an aircraft. Do not use your
headset in an aircraft.
E. Never mount or store your headset over any air bag deployment area.
Serious injury may result when an air bag deploys.
F. Do not open or damage the built-in battery.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 1
Create Date                     : 2013:12:26 15:38:32+08:00
Modify Date                     : 2013:12:26 15:38:32+08:00
Producer                        : Corel PDF Engine Version 15.0.0.486
Author                          : Administrator
Creator                         : CorelDRAW X5
Title                           : UM-BH695-sunitec-EN-131209

EXIF Metadata provided by EXIF.tools