Sunmi Technology T2 POS system User Manual UM V1
Shanghai Sunmi Technology Co.,Ltd. POS system UM V1
UM-V1
T2 User Manual Book Before operating this unit please read these instructions completely and save them Three options for sub screen of T2 Introduction to POS “Take dual 15.6〃as sample” Primary display 15.6〃main screen only (L1521) 15.6〃main screen+10.1〃 consumer screen (L1522) 15.6〃main screen+15.6〃 touch screen (L1523) Simplified Setting Paper exit of printer Cover handle of printer Paper roller cover of printer USB interface Power button It only takes a few steps to turn on this intelligent commercial POS machine: Press the power button, and then the screen lights up. Follow the instructions shown on the initial start-up interface. Two Internet access modes are available for your option. WIFI setting Power button Cover handle of printer ·Press the [Setting] button, start WLAN to enter the WLAN search interface, and search for the available WLAN hotspots. ·Press the WLAN to be connected. If an encrypted network is selected, a password is required for connection. Press the power button to start the POS when the machine is powered off; Press the power button for 2-3 seconds to turn off or restart the POS when the machine is working. Press the power button for 11 seconds to power off the machine when it crashes. For opening the paper roller cover of the printer to change paper. LAN setting How to download/use App The POS is applicable to cashing environments of commercial customers from a wide variety of sectors such as catering services, high-end department stores, convenience stores, banking services, information stations, interactive multimedia facilities, advertisingexposure systems, etc. Open the App Market while you are connected to the Internet to view, download and install the App. Access the Help App in the POS machine for more use instructions USB interface Primary display A touchscreen for operators. Secondary display For connecting an external keyboard, mouse or U-disk. A screen that plays advertisement for customers. lt is optional, based on the POS. Paper exit of printer Cable cover For printing a receipt at the power-on state. Behind the cover are ports that connect various cables. POS Machine Installation Interface cover Secondary display TF card slot Micro USB debugging port Debugging function button Cable cover 5V TXD RXD GND Open the paper roller cover Pull the printer handle out, and the paper roller cover pops out automatically. TF card slot For connecting an external TF memory card. Micro USB debugging port, debugging function button Place 80mm thermo-sensitive paper, pull out a section from the paper exit, and then close the paper roller door. For debugging the POS. Cashbox Port This port can only supports 24V/1A cashbox.If you use a 12V cashbox, there maybe has a potential risk of circuit burns. Install printing paper Power port LAN port Cashbox port Serial port USB port Headset jack USB port Connect the power cable Connect the power interface of the adapter to the power port at the bottom of the POS. Connect the other end of the adapter to the power socket. Wrong Operation Paper Jammed Troubleshooting 1 Firstly, open outward the cover of the printer cutter Please do not tilt the printing paper. Please do not get printing paper caught in the aperture of the paper case cover by accident. 2 Secondly, adjust the cutter knob upwards until it is removed. Do not pull the printing paper roll in the paper case tray too long. Common Troubleshooting Symptom Please do not put loose paper into the paper case. Please pay attention to the correct orientation of the printing paper. Solution Device Crash · Press the power button for 11 seconds to reboot. Printer Out of Service · Make sure the paper rouer cover is closed proerly; · Please check if it is the paper jam; If got an empty printout · Please check if put the thermal paper in the wrong side; · Please check if you have used the appropriate 80mm width thermal paper; If got a garbled printout · Please check if the print head was not clean, if so, please use a cotton-wool bud with alcohol to clean it; · Please use the thermal paper with high quality to avoid the garbled printout; Specification Operating system Android 7.1 Processor Qualcomm Snapdragon Qcta-core Main-screen 15.6-inch FHD1920×1080 resolution Memory 16GB ROM + 2GB RAM Touchscreen Multi-touch capacitive screen WiFi Dual-band WiFi, 802.11a/b/g/n(2.4GHz/5GHz) supported Bluetooth Bluetooth 4.0 BLE and iBeacon supported Printer 80mm printer head, paper roll diameter of 80mm, with an auto-cutter Speaker 1.2W each, max 90dB External memory card MicroSD (TF) supported, maximum 64GB External ports 5 × USB type-A ports, 1× RJ11 serial port, 1× RJ12 24v cashbox port, 1 × RJ45 LAN port, 1× headset jack, 1× power port, 1× Micro-USB debugging port Overall dimensions (H×W×D) cm 40.7 × 38.2 × 23.2cm Power adapfor Model: EA10681P-240 Input: AC 100~240V/2.0A Output: DC 24V/2.5A Name and Content of Toxic or Harmful Substances in this Product Toxic or Harmful Substances or Elements Part Name Lead Mercury Cadmium (Pb) (Hg) (Cd) Hexavalent chromium (Cr(VII) Components of circuit board Print head component : Means that the content of the toxic or harmful substance in all homogeneous materials of this part is below the limit stipulated in SJ/T11363-2006. : Means that the content of the toxic or harmful substance in at least one of the homogeneous materials of this part is beyond the limit stipulated in SJ/T11363-2006; but as for the component marked with “×” on the table, the content is beyond the l imit since there is no alternative mature technology in the industry yet. The products reaching or exceeding the environmental service life shall be recycled per “Regulations on the Control and Management of Electronic Information Products” and shall not be littered. Specification of 15.6〃customer display Monitor 15.6-inch FHD1920×1080 resolution Touchscreen Multi-touch capacitive screen Specification of 10.1〃customer display Monitor 10.1-inch 1024×600 resolution Polybrominated Polybrominated biphenyls diphenyl ethers (PBB) (PBDE) Package content T2 Instruction Manual Precautions FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: Warning Important Safety Instructions · Please insert the AC plug into the AC outlet according to the identifying input on the power adapter; · Avoid installing or using during thunder and lightning,other wise lightning stroke may occur; · It is prohibited to use the device in any places with potential explosive gases; · Cut off the power immediately if there is abnormal smell, overheating or smog; Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. · Nonprofessionals shall not open the power adapter anyhow so as to avoid dangers; · Do not touch the sharp paper cutting tool! the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference · The device is a Grade A product. In living environment, the product may cause radio interference. Therefore, users may be required to take practical measures against the interference. · About the battery replacement: 1. It may cause explosion with wrong type battery 2. Old battery which is replaced should be handled by repair man, do not put it in fire! · Adapter shall be installed near the equipment and shall be easily accessible. · The operating temperature of the device between 0℃ to 45℃. · The device complies with RF specifications when the device used at 20cm form your body. · This product can be used across EU member states. Recommendation · Do not use the device near water or in humid environment.Keep liquid from falling onto the terminal; · Do not use the device in extremely cold and hot environment, e.g. around fire or lighted cigarettes; · Do not smash, throw or bend the device; · Use the device in clean and dustfree environment as much as possible and keep small items from falling into the terminal; · Do not use it near medical devices unless permitted. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, Statement The company is not responsible for the following behaviors: · Damages caused by using and maintaining the device without following the User Guide; · Damages or problems caused by selection of objects or Consumables (products which are not the initial ones provided or recognized by the company). In this case, the company will not undertake any responsibility. No one is entitled to modify or change the product unless permitted by the company. which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device complies with RF specifications when the device used at 20cm form your body. Disclaimer Discrepancies between the product and the file concerning details may raise due to product updates. Please be subject to the material object. The company reserves the right to interpret the file and the right to revise this manual without prior notices. Please make sure the temperature for adapter will be from -10 ℃ to 40 ℃. Please make sure the temperature for device will be from -10 ℃ to 40 ℃. Technical features and characteristic the product includes the following features and characteristics: Operation Frequency Transmitted BT 2402MHz-2480MHz 6dBm BLE 2402MHz-2480MHz 1dBm wifi 2412MHz-2462MHz 18dBm wifi 5150MHz-5250MHz 5725MHz-5850MHz 14dBm
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42 Format : application/pdf Title : T2 中性英文版用户指南(美版)_20180809 Metadata Date : 2018:08:27 17:45:01+08:00 Modify Date : 2018:08:27 17:45:01+08:00 Create Date : 2018:08:27 17:45:01+08:00 Creator Tool : Adobe Illustrator CC 2017 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 72 Thumbnail Format : JPEG Thumbnail Image : (Binary data 4917 bytes, use -b option to extract) Instance ID : uuid:423349e9-b5d8-1b46-a7b2-83ccc6cd5c9a Document ID : xmp.did:6e57f8c4-055e-4b99-8b6e-5572a3659679 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:bba6e1d4-63ea-4a0a-a8af-608f8b435043 Derived From Document ID : xmp.did:bba6e1d4-63ea-4a0a-a8af-608f8b435043 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:07fe9ed1-210d-4a39-92b6-1b59da13b510, xmp.iid:6e57f8c4-055e-4b99-8b6e-5572a3659679 History When : 2016:08:22 15:59:19+08:00, 2018:08:27 17:44:59+08:00 History Software Agent : Adobe Illustrator CC 2015 (Macintosh), Adobe Illustrator CC 2017 (Macintosh) History Changed : /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : True N Pages : 1 Max Page Size W : 320.000105 Max Page Size H : 159.999890 Max Page Size Unit : Millimeters Font Name : PingFang-SC-Heavy, PingFang-SC-Regular Font Family : 苹方, 苹方 Font Face : 特粗, 常规 Font Type : TrueType, TrueType Font Version : 10.11d9e1, 10.11d9e1 Font Composite : False, False Font File Name : PingFang Heavy.ttf, PingFang Regular.ttf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE 165 C Swatch Group Name : 默认色板组 Swatch Group Type : 0 Swatch Colorant Swatch Name : PANTONE 425 C, AutoCAD Color, AutoCAD Color 2, AutoCAD Color 6, C=0 M=72 Y=92 K=0, C=64 M=56 Y=52 K=2, C=0 M=0 Y=0 K=70, PANTONE 425 C _副本, PANTONE 165 C Swatch Colorant Type : SPOT, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, SPOT, SPOT Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, RGB, Lab Swatch Colorant Cyan : 0.000000, 92.971700, 37.241200, 72.725999, 0.000000, 63.784200, 0.000000 Swatch Colorant Magenta : 0.000000, 87.972802, 76.470602, 66.765797, 72.000000, 55.803800, 0.000000 Swatch Colorant Yellow : 0.000000, 89.019603, 0.000000, 65.303999, 92.000000, 51.888300, 0.000000 Swatch Colorant Black : 76.999998, 79.998499, 0.000000, 79.150099, 0.000000, 1.654100, 70.000000 Swatch Colorant Red : 240 Swatch Colorant Green : 95 Swatch Colorant Blue : 0 Swatch Colorant L : 64.705902 Swatch Colorant A : 59 Swatch Colorant B : 68 Producer : Adobe PDF library 15.00 Page Count : 6 Creator : Adobe Illustrator(R) 17.0 For : �տ˱�, Bounding Box : -589 -290 4309 1039 Container Version : 11 Creator Version : 21EXIF Metadata provided by EXIF.tools