Sunmi Technology W6900 Smart POS system User Manual UM V1
Shanghai Sunmi Technology Co.,Ltd. Smart POS system UM V1
UM-V1
![](/img.php?id=3901042&img=bg1.png)
Power button
Volume buttons
Menu buttonHome buttonReturn button
Instructions for charging and battery
This device supports charging by USB cable or dock.
· Connect the 5V adapter to the power supply socket.
· Connect the USB cable to USB interface of the device.
· The screen will display charging icon during charging.
· Please check the USB connect if there is no charging icon.
Instructions/Notes for battery
· This device adopts 3.6V/5200mAh Lithium battery, please don’t
remove the battery.
· In order to protect the battery life, please charge your device
whenever possible and don’t let battery to fully drain before
charging.
Open handle
NFC reader
①
③
②
SIM card slot
Battery
Battery cover
Indicator light
Printer
Speaker
IC card reader
Magnetic card reader
Ultra-simple setting
Trouble shooting
Printer not working
· Make sure the cover of paper container is closed correctly.
· Make sure the right printing pater is used and fed.
· Check whether 58mm × 40mm thermal paper roll is fed into the
paper container.
· If the printed paper is blank, please check whether the paper roll
has been installed in the correct direction.
The device can’t be power on(eg, exhausted battery).
· Connect the device properly with a USB cable to charge for
three minutes.
· Check whether the charging icon is displayed or not.
What we can do if the system freezes
Press the power button for 11 seconds to reboot.
Printing paper
SIM
SAM card slot
Strap ring
USB interface
Indicator light
Remind the payment steps for band card.
USB interface
Use for charging or developer debugging.
Camera
5M Auto Focus, 1D&2D scanner.
Flash light
For lighting in camera mode.
SAM card slot
For inserting encrypted SAM cards.
SIM card slot
Note: To prevent system errors, please make sure the device is off when
you insert or remove the SIM card.
· Move the battery cover horizontally to open.
· Insert/remove SIM card in the direction as shown.
· Fasten the battery cover horizontally.
(Support GSM/CDMA/WCDMA/TDS CDMA/EVDO/LTE SIM card.)
Battery
Avoid contacting with water, metal material and other electrically
equipment while in use.
Strap ring
For fixing handheld strap to prevent slippage.
Extend pins
To connect to dock.(Need to buy dock separately)
Printing instructions
This device support 58mm thermal paper with the specification of
57±0.5mm×Ø40mm
· Please open pater container with open handle, as shown in
Fig.1. Please don’t open directly to damage print gear.
· Put the paper correctly into the pater container as shown and
pull some paper outside the cutter, as shown in Fig.2.
· Close the cover of pater container to finish print paper feeding,
as shown in Fig.3.
Note: If the printed paper is blank, please check whether the paper roll has
been installed wrong.
Only a few steps to start the smart business device
① 2G/3G/4G settings, in the power-off status, insert related 2G(GSM/CD-
MA)/3G(WCDMA/TDS CDMA/EVDO)/4G(LTE) SIM card and then power it on.
(For card support details, please read the technical specification table)
② Long-press the power button for 2 to 3 seconds, and then the screen is
lightened. Enter the first power-on interface and just operate according to
instructions. The device provides two Internet accessing modes for selection.
③ WIFI setting
·Click the [setting] button, then enable WLAN, enter the WLAN search
interface, and wait for its search for accessible WLAN hotspots and the
result;
·Click on the WLAN you want to connect to. If you select an encrypted
network, you need to enter the access code to connect.
How to download/un-install applications
In the networked mode, open the application market, browse and download
applications to complete the installation of related applications.
Camera
Flash light
Extend pins
Software uninstall method: select "Settings-> Applications-> Manage
Applications-> Uninstall" to uninstall the application; or long press the
icon to drag it to the trash to uninstall.
USB interface
supply socket
Adapter
Power button
Short Press:
Wake up the screen, lock the screen.
Long Press:
Long press for 2-3 seconds in power off mode switches on the
device.
Long press for 2-3 seconds in normal operation mode selects
power off or reboot.
Long press for 11 seconds when system is frozen automati cally
reboots.
Volume buttons
Volume adjusts. These buttons can be set as quick scan button by
app setting.
Printer
For printing sales slips in power on mode.
Return button
Tap to return to the previous screen.
Home button
Tap to quickly go back home screen.
Menu button
Tap to quickly view the background apps.
Select the app and slide laterally to close.
Magnetic card reader
Read the magnetic stripe information of bank cards.
IC card reader
Read the chip-based band cards.
NFC reader
Read the contactless card information.
Please read “Help App” in the device
for more information on user’s guidance
Name and Content of Toxic or Harmful
Substances in this Product
Means that the content of the toxic or harmful substance
in all homogeneous materials of this part is below the limit
stipulated in SJ/T11363-2006.
Means that the content of the toxic or harmful substance in
at least one of the homogeneous materials of this part is
beyond the limit stipulated in SJ/T11363-2006; but as for
the component marked with “×” on the table, the content is
beyond the l imit since there is no alternative mature
technology
in the industry yet.
Part Name
Components of circuit board
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr(VII)
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Toxic or Harmful
Substances
or Elements
The products reaching or exceeding the environmental service
life shall be recycled per “Regulations on the Control and
Management of Electronic Information Products” and shall not
be littered.
![](/img.php?id=3901042&img=bg2.png)
Precautions
Product technical specifications
Camera 500W AF
FLASH 8GB Nand Flash
CPU MTK 6737
CPU basic
frequency Quad-core 1.3GHz
Keys Power key, volume key,
Display 5.5 inch IPS, resolution 1280*720
Operating
system Android 6.0
Bluetooth Support of bluetooth 3.0/4.0BLE and iBeacon
RAM 1GB LPDDR3
Interfaces USB Type C,SIM、PSAM、USB OTG
Printer type Thermal Printer
Printer paper
spec Width 58mm, maximum diameter 40mm
Touch screen Capacitive multi-touch screen, supportive of the glove mode
Wireless data
2G:B2/B3/B5/B8
3G:wcdma(B1/B2/B4/B5);EVDO(BC0/BC1)
4G:B2/B4/B7/B17/B28
Item Technical Specifications
Package content
One host
One user guide (including package content, product warranty
card and product qualification certificate)
One power adapter
One USB cable
Battery 3.6V/5200mAh
IC card reader ISO7816\EMV2000\PBOC3.0
Contactless
card reader ISO 1443A/B
SAM Slot ISO7816
Magnetic card
reader Track 1/2/3, Bi-directional, ISO7810/7811/7813
Outline
dimensions L211 mm × W83 mm × H54 mm
Adapter OUTPUT:DC5V/2A
INPUT:AC100~240V/0.3A 50/60Hz
Safety Warning
· Insert the AC plug into the AC socket-outlet corresponding
to the identification input on the accessory power adapter;
· It must not be used where there is any potential explosive
gas;
· This is a Class A product. In a living environment, this prod
uct may cause radio interference.
In this case, the user may need to take practical measures
against the interference.
· bout battery replacement:
① There is a risk of explosion if you replace the battery with
a wrong type!
② The replaced battery shall be handed over to repair per
sonnel disposal. Do not throw it into the fire!
Important Safety Instructions
· Try not to install or use the device during lightning, or else
there would be lightning stroke danger;
· When you find unusual smell, overheat or smoke, please cut
off the power immediately;
· Be cautious of the sharp paper knife, and please do not
touch! !
Suggestions
· Do not use it in extremely cold or hot conditions (e.g., near
fire or a lighted cigarette);
· Do not drop, throw or bend it;
· Try to use it in a clean and dustless environment and avoid
tiny articles falling into the terminal;
· Do not use it near medical equipment without permission.
Declaration
The company shall not be responsible for the following actions
· Any damage caused by not using and maintaining it under the
conditions described in the guide;
· Any damage or problem caused by optional parts or con
sumptive materials (not the original products provided by the
company or approved products), the company will assume no
responsibility for this. It is not allowed to modify or change
the product without the consent of the company.
· The operating system of this product supports official system
update. If users install ROM system from the third party or
modify the system files by means of cracking, it may lead to
system instability, as well as security risk and security threat.
Disclaimer
Owing to the update of the product, some details of this docu-
ment may not be in conformity with those of the product.
Please refer to the material object. The company reserves the
right to interpret this document. The company reserves the
right to modify this instruction book without prior notice.
Smart POS System
User’s Guide
Wi-Fi Build-in WIFI 802.11 a/b/g/n(2.4G/5G)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: 2AH25W6900
NOTE: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
With RF exposure requirements, a minimum separation distance of
1.0cm must be maintained between the user’s body and the handset,
including the antenna.
Third-party belt-clips, holsters, and similar including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this
device should not contain any metallic components. Body-worn
accessories that do not meet these requirements may not comply with
RF exposure requirements and should be
avoided.
Specific Absorption Rate (SAR) information:
This wireless phone meets the government's requirements for exposure
to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
FCC RF Exposure Information and Statement. The SAR limit of USA
(FCC) is 1.6W/kg averaged over one gram of tissue.
Device types: W6900 has also been tested against this SAR limit. The
highest SAR value reported under this standard during product certifica-
tion when properly worn on the body is 1.856W/kg(10gSAR, test
distance:0mm,limit 4W/kg)and 1.477W/kg (1gSAR, test distance
:5mm,limit 1.6W/kg). This device was tested for body-worn
operations with the back of the handset kept 0mm and 5mm from the
body. To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 0mm and 5mm separation distance between
the user's body and the back of the handset. The use of belt clips,
holsters and similar accessories should not contain metallic components
in its assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements, and
should be avoided.
Manufacture
Room 505 No.388 Song Hu Road Shanghai, China
Technical features and characteristic
the product includes the following features and characteristics:
GSM850
GSM1900
WCDMA bandII
WCDMA bandIV
WCDMA bandV
LTE Band 2
LTE Band 4
LTE Band 7
LTE Band 17
CDMA BC0
CDMA BC1
BT
BLE
Operation Frequency
824MHz-849MHz
1850MHz-1910MHz
1850MHz-1910MHz
1710MHz-1755MHz
824MHz-849MHz
1850MHz-1910MHz
1710MHz-1755MHz
2500MHz-2570MHz
704MHz-716MHz
824MHz-849MHz
1850MHz-1910MHz
2402MHz-2480MHz
2402MHz-2480MHz
Transmitted
33dBm
29dBm
21.5dBm
22.5dBm
22.5dBm
23.5dBm
23.5dBm
21.5dBm
23.5dBm
22dBm
21.5dBm
-1dBm
6dBm
wifi
2412MHz-2462MHz
5150MHz-5250MHz
5250MHz-5350MHz
5725MHz-5850MHz
18dBm
18.5dBm