Sunrex Technology RX713A Wireless Dongle User Manual KM713A

Sunrex Technology Corp Wireless Dongle KM713A

User Manual

KM713A User Manual
Important Information
For Windows® XP and Windows® Vista operating system, you can use the
keyboard and moue immediately after plugging the dongle (receiver) into the USB
port. But the hotkey : ”Fn+F1”, ”Fn+F8”, ”Fn+F9”, ”Fn+F10”, ”Fn+F8”, ”Fn+F11” need
install driver.
Hardware Installation
1. Plug in the dongle into your available USB port.
2. Make sure the batteries of the keyboard and moue are installed correctly. Please
follow the polarity signs in the battery compartment.
3. Please make sure the power switch on the back of the mouse is switched to “ON”
before using the mouse. When not in use, please turn the power switch to “OFF”
for power saving.
ID Pairing Procedure
Keyboard mouse and dongle has paired when ship out. If it can’t work, please follow
the steps to process the ID pairing procedure.
1. ID pairing/connect button location:
Keyboard ID pairing/connect button on the bottom of the keyboard.
Mouse ID pairing/connect button on the bottom of the mouse.
2. After you plug the dongle into the USB port, please hold the keyboard and mouse
close to the dongle within 0.5M and press the “CONNECT” button over 5 second.
3. If ID pairing is successful, the LED on the dongle will bright 3 seconds.
4. If ID pairing is fail, please follow the steps above to pair ID.
Note:
-Make sure your PC is ON and running when doing the pairing procedure.
-You don’t have to pair ID again after changing batteries. If it can’t work, please follow
the steps above to pair ID.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
Driver Installation
1. Driver name: “HPBattery.exe”.
2. Dual click the “HPBattery.exe”. The driver icon will show at the right-bottom of the
Windows system tray when the driver is loaded.
3. Function:
u Battery volume detect: Battery volume full à green
Battery volume 50% full à yellow
Battery volume low à red
u Fn+F1àWindows help
u Fn+F2à Replay
u Fn+F3à Rewind
u Fn+F4à Stop
u Fn+F5à Play/Pause
u Fn+F6à Fast forward
u Fn+F7à Skip
u Fn+F8àEject
u Fn+F9àDisplay ON/OFF
u Fn+F10à Decreasing Brightness
u Fn+F11à Increasing Brightness
Import Usage Information
u Battery:
1. We recommend using alkaline batteries for a longer battery life.
2. Don’t mix different types of batteries or new and old batteries together. Always
replaced old batteries with new and same type batteries.
3. Remove batteries after long periods of non-use. Battery leakage or corrosion may
damage the device quality and cause danger.
u Mouse:
1. This optical mouse senses light to defect mouse’s movement; therefore, it cannot
work on a glass, translucent, reflective, or dark color surface.
2. The mouse can work only a clean, flat, non-slippery, opaque, and light color
surface in order to ensure smooth and accurate cursor action.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Notice
Operation is subject to the following two conditions: (1) this device may
not cause interference and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
PDF created with FinePrint pdfFactory Pro trial version http://www.pdffactory.com

Navigation menu