Suntech ST300 Vehicle Tracker User Manual ST300 3

Suntech International Ltd. Vehicle Tracker ST300 3

Users Manual

ST300 User Manual Suntech International Ltd.
ST300 User Manual 2 1. Introduction This document describes features, protocols and detail operation of ST300. If there is another operation description document for special buyer to customize or model and the contents of the document is different with this, customizing document should be applied for special buyer. 2. Overview Device consists of GPRS, GPS and event parts. The main purpose of device reports getting GPS position and other informs of vehicle to server periodically. Device can control or check connected lines and support additional functions. 2-1. Operation Mode The device has 3 operation modes, driving, parking and emergency. ** Driving : Driving status when ignition is on. ** Parking : Parking status that starts if ignition is off during more than T1. ** Emergency : Once panic button is On or any other status as per designed. The device sends emergency reports until A1 times or receiving server acknowledge. 2-2. Report AVL reports GPS and some information at predefined interval, depending on the current modes. Also, AVL sends some alerts, for example, movement at the parking condition, changing of connected input line and so on. Device distinguishes all reports with 6 types, Status report, emergency, event, alert, alive and command response. Device can store reports when reporting route (For example, GPRS condition) is not successful. Storage capacity is up to 2,000 status reports, 50 emergency reports, 50 alert reports (include event reports) and 1500 bytes as command response. In case of status reports, oldest report is erased and new report is buffered when the buffer is full and new status report enters (FIFO). When reporting condition is recovered, device starts sending all buffered reports. Also, this capacity can increase if it is needed. Each type of reports has priority, and priority is as below. Emergency  Command Response  Alert  Status Report  Alive (Lowest)
ST300 User Manual 3 Emergency is the first to be sent after recovering GPRS condition. 2-3. Setting Parameter Parameters of device can be changed by GPRS or SMS, and some control can be realized also in the same way. Detail protocols are described in Chapter 4. 2-4. Features Key features are described here; - Power Down Device can process two steps of power-down, Sleep and Deep Sleep, for reducing power consumption when the vehicle is parked. - LED Indicator LED indicates GPRS and GPS states. It’s helpful to check error cause. - Events Device has 2 output lines, 3 input lines and ignition line. - Update Firmware by Over The Air (FOTA) When Firmware of device has some error or has to be changed for a new service to be implemented, device can update internal ROM file by over the air (FOTA), remotely via GPRS. Customers do not need to visit every vehicle to download the new firmware. Method of FOTA describes at “SunTech_OTA_UA_Protocol” document in detail. - Parking Lock Device can check whether the vehicle moves off the preset parking boundary or starts driving without ignition on. In the case that it notes the unauthorized moving or driving, it sends emergency report immediately. - Over speed Device can check speed of vehicle and send alert of over-speed to server. - GPS Antenna Checking Device can alert when GPS antenna is disconnected.
ST300 User Manual 4 It’s applicable only for models that have external antenna. - Main Power Checking The device can recognize the main power and inform to server when main power line is disconnected or main power drops below preset value. It’s applicable only for battery model. - Battery Error Alert Device can alert about battery error related on charging. It’s applicable only for battery model. 3. Protocol Construction All command and reports are string and follows below format. Every filed is distinguished by semi colon. All report string from device is ended by ‘＼r’ (0x0D). Command message format (from server to device) HDR DEV_ID VER Field 1 Field 2 …Field n Field Definitions Remark HDR String “SA200” + Command type DEV_ID 6 char. Device ID of AVL VER “02” Protocol Version. This is fixed with “02”. Field 1 ~ n String Contents Device ID is unique number of each device that consists of 6digits. If the command has invalid value or DEV_ID of the command that is sent by GPRS or SMS is not matched with DEV_ID of the unit. Report message format (from device to server) HDR DEV_ID SW_VER Field 1 Field 2 …Field n Field Definitions Remark HDR String “SA200” + Report type
ST300 User Manual 5 DEV_ID 6 char. Device ID of AVL VER “001” Software version that the device has. Field 1 ~ n String Contents 4. Commands When the device is received a command, it responds with response string and changes some parameters or acts related operation. 4-1. Network Parameters Setting HDR DEV_ID VER AUTH APN USER_ID USER_PWD SEVER_IP SEVER_PORT B_SEVER_IP B_SEVER_IP SMS_NO PIN_NO ● Definition : Set network parameters and PIN number. Field Definitions Unit Remark HDR “SA200NTW” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version AUTH ‘0’ /‘1’/’A’ GPRS authentication 0 : PAP(‘NO’ in Synctrack) 1 : CHAP(‘YES’ in Synctrack) A : Automatic GPRS set. In this case, parameters in APN, USER_ID and USER_PWD field should be empty. APN String Access Point Name USER_ID String ID for GPRS Access USER_PWD String Password for GPRS Access SEVER_IP String Server IP Address SEVER_PORT String Server Port B_SEVER_IP String Backup Server IP Address B_SEVER_PORT String Backup Server Port SMS_NO String Phone number what the device sends SMS report to. This can be used for backup in the area that if GPRS condition is not good. Or, it can be used main report method when IP and Port are empty.
ST300 User Manual 6 For no use, it should be empty. PIN_NO String PIN Number to release PIN lock if it is enabled <example> [command] SA200NTW;850000;02;0;internet;;;111.111.111.111;8600;;;; [response] SA200NTW;Res;850000;010;0;internet;;; 111.111.111.111;8600;;;; SA200NTW;Res;850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;; <notes> ** If network does not require User ID and Password, these fields should be empty. Automatic GPRS Set It the device is set to ‘Automatic GPRS Set’, the device set GPRS parameters automatically depending on inserted SIM. For example, if Airtel SIM is inserted, the device set AUTH to 0, APN to “aitelgprs.com”, USER_ID and USER_PASS to empty. And the device reports response string after adding real GPRS parameters when automatic GPRS set is selected. 4-2. Report Parameter Setting HDR DEV_ID VER T1 T2 T3 A1 SND_DIST T4 SMS_T1 SMS_T2 SMS_PACK_NO ANGLE_RPT RPT_TYPE ● Definition : Set parameters related on report interval. Field Definitions Unit Remark HDR “SA200RPT” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version T1 String Sec Interval for sending status report in parking mode Range : 0 ~ 86400 If 0, report in parking will be sent only one time when vehicle starts parking. T2 String Sec Interval for sending status report in driving mode Range : 0 ~ 60000
ST300 User Manual 7 If 0, report in driving will be sent only one time when vehicle starts driving. T3 String Sec Interval for sending status report in emergency mode Range : 0 ~ 9999 If 0, emergency report will be sent only one time when emergency state occurs. A1 String Number of attempts for emergency report until the device gets acknowledge from server If 0, no emergency report will be sent. SND_DIST String Meter Distance interval for sending status report. Range : 0 ~ 60000 (60km) If 0, status report related on moving distance is disabled. If not 0, stats report is send when traveled distance reaches predefined SND_DIST. T4 String Sec Interval for sending keep alive string SMS_T1 String Min Interval for sending status report in parking mode SMS_T2 String Min Interval for sending status report in driving mode SMS_PACK_NO String Report No in one SMS message ANGLE_RPT String Degree Report STT message if it’s greater than ANGLE_RPT. 0 : Disable Range : 1 ~ 179 RPT_TYPE String Set the type of reporting. 0: FIFO : First in First Out. 1: LIFO : Last In First Out. <example> [command] SA200RPT;850000;02;180;120;60;3;0;0;0;0;0;0;0 [response] SA200RPT;Res;850000;010;180;120;60;3;0;0;0;0;0;0;0 <notes> ** If report interval is set big number, network may disconnect GPRS connection because GPRS communication is not progressed for a long time. So, unit may not receive command by GPRS. T4 is for protecting against this disconnection by sending short data with short term. ** Alive report can be sent only when the device has no data to send during T4 interval. 4-3. Event Parameter Setting
ST300 User Manual 8 HDR DEV_ID VER IGNITION T1 T2 IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT IN2_CHAT IN3_CHAT OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVEPULSE1_NO PULSE1_ON PULSE1_OFF PULSE2_NO PULSE2_ON PULSE2_OFF IN4_TYPE IN5_TYPE IN4_CHAT IN5_CHAT BAUD ● Definition : Set parameter related event. Field Definitions Unit Remark HDR “SA200EVT” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version T1 String Sec Delay for entering idle mode after ignition goes to off T2 String Sec Delay for entering active mode after ignition goes to on IN1_TYPE ‘0’ ~ ‘7’ 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button 13 = Disable Immobilizer if it’s activated by jammer detector. Default = ‘3’. Only the device that included voice option (audio circuit) can be set to ‘Call1 Button’ or ‘Call2 Button’. IN1_CHAT String 100ms Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked.
ST300 User Manual 9 OUT1_TYPE ‘0’ ~ ‘5’ 0 = GPIO 1 = immobilizer 2 = Immobilizer & Auto active Auto active means immobilizer is activated automatically when the vehicle starts parking. 3 = Pulse 4 = LED Out for indicating call status. Refer 7-2-3. 5 = Buzzer OUT1_ACTIVE ‘0’ or ‘1’ 0 = Open when out1 is active 1 = GND when out1 is active PULSE1_NO String Pulse number when out1 type set to pulse. Range : 0 ~ 9999 If pulse no is 9999, pulsing runs permanently. PULSE1_ON String 100ms Active time of pulse1 Range : 0 ~ 9999 It should be set with even number. PULSE1_OFF String 100ms Inactive time of pulse1 Range : 0 ~ 9999 It should be set with even number. BAUD ‘0’ ~ ‘4’ It’s available when extra events support RS232. Baud-rate 0 = No use 1 = 4800bps 2 = 9600bps 3 = 19200bps 4 = 38400bps 5 = 115200bps If the device does not support RS232, it should be 0.
ST300 User Manual 10 <example> [command] SA200EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 [response] SA200EVT;Res;850000;010;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 <notes> ** If IGNITION is set to ‘0’, device doesn’t check driving or parking state of the vehicle. It reports status string with idle mode always, and cannot support parking lock and the service that enters sleep or deep sleep automatically when the vehicle is parked. ** If IGNITION is set to ‘2’, the device checks driving or parking state of the vehicle with voltage range of vehicle’s battery. We named it as ‘Virtual Ignition’. Virtual ignition can operate when the device installed into real vehicle and it may be need adjustment of voltage range for special vehicle. For setting method, please refer 6.3. ** In case of pulse, pulse time may have tolerance about dozens of ms. ** Immobilizer, LED Blink line and Buzzer type cannot set both OUT1 and OUT2 simultaneously. ** In case that a event is set to “door sensor”, active state means door is opened. ** If device has the Handsfree kit, each time the volume up button is pressed once, the speaker volume is turned up as below. 0 -> 1 -> 2 -> 3 -> 4 ->5 ->0 -> 1 -> 2 ->3 -> 4 -> 5 - > 0 -> 1 -> …. (0 : Volume mute, 5 :Max Volume) Type of no supported event line is fixed to “No Use”. Below table is for example of 4 line event model. Field Definitions Unit Remark HDR “SA200EVT” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version IGNITION ‘0’ ~ ‘2’ Ignition using state 0 : Not use ignition 1 : Use ignition Line 2 : Virtual ignition(power) 3 : Virtual ignition (motion) T1 String Sec Delay for entering idle mode after ignition goes to off T2 String Sec Delay for entering active mode after ignition goes to on
ST300 User Manual 11 IN1_TYPE ‘0’ ~ ‘5’ 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button 13 = Disable Immobilizer if it’s activated by jammer detector. Default = ‘3’. Only the device that included voice option (audio circuit) can be set to ‘Call1 Button’ or ‘Call2 Button’. IN1_CHAT String 100ms Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked. OUT1_TYPE ‘7’ 7 = No Use OUT1_ACTIVE ‘0’ or ‘1’ PULSE1_NO ‘0’ PULSE1_ON ‘0’ PULSE1_OFF ‘0’ BAUD ‘0’ 0 = No use <example> [command] SA200EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 [response] SA200EVT;Res;850000;010;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;8;8;0;0;0 <notes> ** In case of event 4 line model, IN2_TYPE, IN3_TYPE, IN4_TYPE, IN5_TYPE, OUT1_TYPE and OUT2_TYPE should be ‘No Use’. Type and chat time of non used event lines are set to ‘No Use’ and ‘0’ automatically although these filed of command is set to other value. 4-4. GSM Parameter Setting HDR DEV_ID VER SMS_LOCK SMS_MT1 SMS_MT2 SMS_MT3
ST300 User Manual 12 SMS_MT4 IN_CALL_LOCK CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5 CALL_MO1 CALL_MO2 ● Definition : Set parameters related SMS or Call. Field Definitions Unit Remark HDR “SA200GSM” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version SMS_LOCK ‘0’ or ‘1’ Lock of Receiving Commands by SMS Disable (0) / Enable (1) If enabled, only commands that receives from SMS_MT1 ~ MT3 number can be accepted. SMS_MT1 String Up to 20 char. Phone number for SMS commands SMS_MT2 String Up to 20 char. Phone number for SMS commands SMS_MT3 String Up to 20 char. Phone number for SMS commands SMS_MT4 String Up to 20 char. Phone number for SMS commands IN_CALL_LOCK ‘0’ or ‘1’ Lock of Incoming Call Disable (0) / Enable (1) If enabled, only call from CALL_MT1 ~ MT5 number can be accepted. CALL_MT1 String Up to 20 char. Phone number for call CALL_MT2 String Up to 20 char. Phone number for call CALL_MT3 String Up to 20 char. Phone number for call CALL_MT4 String Up to 20 char. Phone number for call CALL_MT5 String Up to 20 char. Phone number for call CALL_MO1 String Up to 20 char. Phone number for outgoing call from device CALL_MO2 String Up to 20 char. Phone number for outgoing call from device <example> [command] SA200GSM;850000;02;0;;;;;0;;;;;;; [response] SA200GSM;Res;850000;010;0;;;;;0;;;;;;; <notes> ** When SMS or Call numbers are not set, that field should be empty. 4-5. Service Parameter Setting
ST300 User Manual 13 HDR DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPEZIP GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL GEO_FENCE DATA_LOG ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET JAM_CHK_DIST JAM_CHK_TM ● Definition : Set parameters related report. Field Definitions Unit Remark HDR “SA200SVC” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version PARKING_LOCK ‘0’ or ‘1’ Parking lock enable (1) / disable (0) If 1, the device checks vehicle position in parking periodically. When the vehicle goes off some boundary or starts moving over some velocity, the device reports parking lock emergency. SPEED_LIMIT String Km/h Over speed limit If 0, the device does not check over speed. If 1 and the vehicle runes over predefined value, device reports speed alerts once. PWR_DN ‘0’ ~ ‘2’ Power saving type 0 : Disabled sleep and deep sleep service 1 : Enabled deep sleep 2 : Enabled sleep CON_TYPE ‘0’ ~ ‘2’ Connection Type with Server 0 = KEEP_CON 1 = KEEP_DISCON 2 = KEEP_NOP Detail explanation is below. ZIP ‘0’ or ‘1’ Use Zip Disable (0) / Enable (1) GROUP_SEND ‘0’ or ‘1’ Group Send for stored data 0 : Disable 1 : Enable. One packet can include up to 5 reports. Group send is explained below.
ST300 User Manual 14 MP_CHK ‘0’ or ‘1’ Main Power Disconnection Check Disable (0) / Enable (1) ANT_CHK ‘0’ or ‘1’ GPS Antenna Connection Error Check Disable (0) / Enable (1) BAT_CHK ‘0’ or ‘1’ Backup Battery Error Check Disable (0) / Enable (1) M_SENSOR ‘0’ ~’4’ Motion Sensor Motion Collision Shock 0 Disable Disable Disable 1 Enable Disable Disable 2 Disable Disable Enable 3 Enable Disable Enable 4 Disable Enable Disable 5 Enable Enable Disable 6 Disable Enable Enable 7 Enable Enable Enable CALL ‘0’ or ‘1’ Support Call with headset Disable (0) / Enable (1) GEO_FENCE ‘0’ or ‘1’ Support Geo-fence Disable (0) / Enable (1) DAT_LOG ‘0’ or ‘1’ Log out with RS232 0 = No Use 1 = Enable getting saved log data by RS232 <example> [command] SA200SVC;850000;02;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0 [response] SA200SVC;Res;850000;010;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0 <notes> ** Function of M_SEMSOR can be used with the model that has motion sensor. If shock or collision detection is enabled, device will report to server when gets any shock or collision. ** If this parameter has been customized, This table should be disregarded and you should follow customized operation document. CON_TYPE 1. KEEP_CON : The device keeps TCP connection always and can receives a command by GPRS. 2. KEEP_DISCON : The device connects TCP connection when the data is sent. After sending, the device disconnects GPRS and TCP connection if it estimates there is no data for sending within
ST300 User Manual 15 3minutes. In this case, it cannot receive a command by GPRS. 3. KEEP_NOP : The device doesn’t send any report after be installed. When the device enters emergency mode or receive ‘Start Report’ command by SMS or RS232, it starts report depending on report parameters. It may be used for saving GPRS fee. Current version cannot support this option. Group Send The device stores data if the vehicle is in no GPRS area. And, the vehicle moves to GPRS available area, device starts sending stored data. If group send option is enabled, the device makes 5 reports to one bundle and send these 5 reports at one time. Group send is useful to speed up sending. M_Sensor 1. Collision: The device sending a event when ignition is ON and have a motion. 2. Shock: The device sending a event when ignition is OFF and have a motion. Jamming detection procedure JAM_CHK_DIST & JAM_CHK_TM are assist for jamming detection to avoid false detection. At least, we recommend use JAM_CHK_DIST for safety. If you use two assist functions, it can detect two case of jamming as follows. *Case of jamming GPRS only. Jamming detected -> JAM_CHK_DIST -> JAM_CHK_TM -> Triggered by JAM_DET mode. *Case of jamming GPRS & GPS. Jamming detected -> JAM_CHK_TM -> Triggered by JAM_DET mode. JAM_CHK_DIST : if 0, skip this function. JAM_CHK_TM : if 0, skip this function. If disable all of assist functions, just triggered by HAM_DET mode after detected jamming. In this case, it’s possible to false detection in weak GSM or strong radio area. 4-6. Additional Parameters HDR DEV_ID VER SVR_TYPE B_SVR_TYPE UDP_ACK DEV_PORT ● Definition : Setting additional parameter requested.
ST300 User Manual 16 Field Definitions Unit Remark HDR “SA200ADP” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version SVR_TYPE ‘T’ / ‘U’ Server Protocol Type T : TCP U : UDP B_SVR_TYPE ‘T’ / ‘U’ Backup Server Protocol Type T : TCP U : UDP UDP_ACK ‘0’ ~ ‘3’ ACK from Server when UPD is used. 0 : No use 1 : ACK when the server receives reports except alive. 2 : ACK when the server receives reports except STT and alive report. 3 : ACK when the server receives emergency report. Command response doesn’t need ACK. DEV_PORT String Device’s port for receiving command from UDP server. It can be used only when UDP server is used. If ‘0’ or empty, the device would use port 9000. If not zero, the device can receive commands with port DEV_PORT. Reserved ‘0’ Reserved ‘0’ Reserved ‘0’ Reserved ‘0’ Reserved ‘0’ Reserved ‘0’ <example> [command] SA200ADP;850000;02;U;T;2;9000;0;0;0;0;0;0 [response] SA200ADP;Res;850000;022;U;T;2;9000;0;0;0;0;0;0 <notes> This command can be applied from software version 22. ACK in case of UDP
ST300 User Manual 17 UDP is protocol that doesn’t check whether the data is transmitted successfully. So, the device checks completion of sending with ACK depending on UDP_ACK type. ACK is sent by server when the data is received. If the ACK is not sent during more than 2 minutes after sending, the device recognizes the data was not reached to server and sends the data again. Examples of ACK report are as below. String Format : “SA200ACK;850000” Zip Format : 0x15 0x85 0x00 0x00 It is recommended ACK_TYPE is set to ‘1’ to confirm all data can be transmitted safely. Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3 Alive X X X X STT X O X X Event, Alert, Etc. X O O X Emergency X O O O 4-7. Set Parameters of Main Voltage HDR DEV_ID VER CHR_STOP_THRES_12 CHR_STOP_THRES_24 DECIDE_BAT_24 OPERATION_STOP_THRES_12 OPERATION_STOP_THRES_24 IGNDET_H IGNDET_L ● Definition : Set some value of main voltage. Field Definitions Remark HDR “SA200MBV” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version
ST300 User Manual 18 CHR_STOP_THRES_12 String Voltage value to stop backup battery charging in 12V vehicle. DECIDE_BAT_24 String Voltage value to check whether the vehicle’s battery is 12V. OPERATION_STOP_THRES_12 String Voltage value to protect vehicle battery. The device operation stops if car battery voltage is lower than this value in vehicle that has 12V power. IGNDET_H String In case of virtual ignition, the vehicle can recognize driving state when vehicle power is more than IGNDET_H. Default = ‘0’ IGNDET_L String In case of virtual ignition, the vehicle can recognize parking state when vehicle power is less than IGNDET_L.Default = ‘0’ <example> [command] SA200MBV;850000;02;10.5;22;19;8.00;18.00;0;0 [response] SA200MBV;Res;850000;122;10.5;22;19;8.00;18.00;0;0 <note> IGNDET_H and IGNDET_L are ‘0’, device check parking and driving automatically. 4-8. Set Parameters of Motion Sensor HDR DEV_ID VER CHR_STOP_THRES_12 CHR_STOP_THRES_24 DECIDE_BAT_24 OPERATION_STOP_THRES_12 OPERATION_STOP_THRES_24 IGNDET_H IGNDET_L VI_ON_THRES VI_ON_DELAY VI_ON_PERCENT VI_OFF_THRES VI_OFF_DELAY VI_OFF_PERCENT ● Definition : Set motion sensor parameters Field Definitions Unit Remark HDR “SA200MSR” Command type DEV_ID 6 char. Device ID VER “02” Protocol Version SHOCK_DELAY String Sec. Delay for entering shock detection mode after ignition off 0 – Disable
ST300 User Manual 19 Range : 1 ~ 21600 (5hour) Recommend : 600 ( 10 min.) MOTION_THRES String Step Detection level of shock violation. Range : 0.04 ~ 2.0 Recommend : 0.04 SHOCK_THRES String Step Detection level of shock violation. Range : 0.04 ~ 2.0 Recommend : 0.04 COLL_THRES String Step Gravity for collision report. Range : 0.1 ~ 2.0 Recommend : 0.7 VI_ON_THRES String 1/255G Threshold value for Motion Virtual Ignition On Range : 3~50 Default : 5 VI_ON_DELAY String Sec. Delay time for Motion Virtual Ignition On Range : 3~999 Default : 10 VI_ON_PERCENT String % Percent for Motion Virtual Ignition On. Range : 30~100 Default: 70 VI_OFF_THRES String 1/255G Threshold value for Motion Virtual Ignition Off Range : 3~50 Default : 5 VI_OFF_DELAY String Sec. Delay time for Motion Virtual Ignition Off Range : 3~999 Default : 10 VI_OFF_PERCENT String % Percent for Motion virtual Ignition Off. Range : 30 ~ 100 Default : 70 <example> [command] SA200MSR;;02;600;0.04;0.04;0.7;5;10;70;5;10;70 [response] SA200MSR;Res;852588;128;600;0.04;0.04;0.70;5;10;70;5;10;70 <notes> * For the shock level, we recommend it to set to 0.04. if it's over than 0.04, the sensor will be more insensitive as it for shock detection.
ST300 User Manual 20 4-11. Control Command HDR DEV_ID VER CMD_ID ● Definition : Controls some functions. Field Definitions Unit Remark HDR “SA200CMD” Command type DEV_ID 6 char. Device ID VER ‘01’ Protocol Version CMD_ID String Control command content Caution : If it’s not correct the Unit ID, ignored. 4-11-1. Status Request ● Definition : Location poll, request of the status report. Field Definitions Unit Remark CMD_ID “StatusReq” Status request If received, the device sends status string instantly. <example> <example> [command] SA200CMD;850000;02;StatusReq [response] SA200STT;850000;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.00; 7;1;0;15.33;100000;2;0002 4-11-2. Reset ● Definition : Reset all of parameters. Field Definitions Unit Remark CMD_ID “Reset” Reset
ST300 User Manual 21 Initialize all parameters with factory value and reboot the device. <example> [command] SA200CMD;850000;02;Reset [response] SA200CMD;Res;850000;010;Reset 4-11-3. Preset ● Definition : Reset all of parameters. Field Definitions Unit Remark CMD_ID “Preset” Report parameter setting values and current device status. Response includes network, report, event, GSM and service parameters. It includes status of device, also. <example> [command] SA200CMD;850000;02;Preset [response] SA200CMD;Res;850000;010;Preset; NTW;0;internet;;;111.111.111.111;8600;;;;1234; RPT;60;180;120;60;3;0;0;;;; EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0; GSM;0;;;;;0;;;;;;;; SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0 [response] event 4 line model NTW;0;internet;;;111.111.111.111;8600;;;;1234; RPT;60;180;120;60;3;0;0;;;; EVT;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;0;0;0;0;0; GSM;0;;;;;0;;;;;;;; SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0 <notes> ** After power on, device sends response string of preset once. ** DEV filed informs current status of device as below. OUT1 0 = Disable OUT2 0 = Disable PWR_DN 0 = Normal BAT_CON 0 = Backup battery is
ST300 User Manual 22 1 = Enable 1 = Enable 1 = Sleep 2 = Deep sleep disconnected. 1 = Backup battery is connected. Field Definitions Unit Remark CMD_ID “PresetA” Report all parameters including additional parameter. <example> [command] SA200CMD;850000;02;PresetA [response] SA200CMD;Res;850000;010;PresetA; NTW;0;internet;;;111.111.111.111;8600;;;;1234; RPT;60;180;120;60;3;0;0;;;; EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0; GSM;0;;;;;0;;;;;;;; SVC;1;120;0;0;0;0;1;1;1;0;0;0;0; ADP;U;T;2;9000;0;0;0;0;0;0; DEV;0;0;0;0;0;0;0;0 <notes> ** This command can be applied from software version 22. ** DEV filed informs current status of device as below. OUT1 0 = Disable 1 = Enable OUT2 0 = Disable 1 = Enable PWR_DN 0 = Normal 1 = Sleep 2 = Deep sleep BAT_CON 0 = Backup battery is disconnected. 1 = Backup battery is connected. TRACKING 0 = Stop Tracking 1 = Start Tracking Anti-Theft 0 = Disable 1 = Enable Reserved Reserved 4-11-4. ACK of Emergency
ST300 User Manual 23 ● Definition : Stop emergency report. Field Definitions Unit Remark CMD_ID “AckEmerg” Acknowledgement of emergency report. The device will stop emergency reports if it is in emergency state. <example> [command] SA200CMD;850000;02;AckEmerg [response] SA200CMD;Res;850000;010;AckEmerg 4-11-5. Enable1 ● Definition : Active Output1. Field Definitions Unit Remark CMD_ID “Enable1” Enable Output1 <example> [command] SA200CMD;850000;02;Enable1 [response] SA200CMD;Res;850000;010;Enable1 [response] SA200CMD;Res;850000;010;Enable1NoUse (in case that IN type is set to ‘No Use’). <notes> ** Output1 line goes to active status. ** If OUT1 set with immobilizer, output1 line goes to active status gradually with pulse in driving mode. ** If OUT1 set with pulse type, output1 line generates pulse and returns inactive state after pulsing out automatically. 4-11-6. Disable1 ● Definition : Inactive Output1. Field Definitions Unit Remark CMD_ID “Disable1” Disable Output1 <example> [command] SA200CMD;850000;02;Disable1
ST300 User Manual 24 [response] SA200CMD;Res;850000;010;Disable1 [response] SA200CMD;Res;850000;010;Disable1NoUse (in case that IN type is set to ‘No Use’). <notes> ** Output1 line goes to inactive status. 4-11-9. Request IMSI ● Definition : Request the unique SIM ID. Field Definitions Unit Remark CMD_ID “ReqIMSI” Request IMSI (unique SIM ID) If received, device sends IMSI of using SIM. <example> [command] SA200CMD;850000;02;ReqIMSI [response] SA200CMD;Res;850000;010;ReqIMSI;724031111553779 4-11-10. Request ICCID ● Definition : Request the ICCID. Field Definitions Unit Remark CMD_ID “ReqICCID” Request ICCID (sequence number that is displayed on SIM) If received, device sends ICCID of using SIM. <example> [command] SA200CMD;850000;02;ReqICCID [response] SA200CMD;Res;850000;010;ReqICCID;89550230000084256668 4-11-11. ReqVer ● Definition : Request software version. Field Definitions Unit Remark CMD_ID “ReqVer” Request device version Device reports Model, Buyer, Protocol and S/W release version.
ST300 User Manual 25 <example> [command] SA200CMD;850000;02;ReqVer [response] SA200CMD;Res;850000;010;ReqVer;SA200E_SAMPLE_STBASE_001 4-11-12. Erase All ● Definition : Erase all of data in buffer. Field Definitions Unit Remark CMD_ID “EraseAll” Erase saved all reports and disable outputs. This is needed to initialize just before device is delivered to a customer. <example> [command] SA200CMD;850000;02;EraseAll [response] SA200CMD;Res;850000;010;EraseAll 4-11-13. Initialize Traveled Distance ● Definition : Initialize the travel distance. Field Definitions Unit Remark CMD_ID “InitDist” Set traveled distance to 0. <example> [command] SA200CMD;850000;02;InitDist [response] SA200CMD;Res;850000;010;InitDist 4-11-14. Initialize Message Number ● Definition : Initialize the message sequence number. Field Definitions Unit Remark CMD_ID “InitMsgNo” Set message number to 0.
ST300 User Manual 26 <example> [command] SA200CMD;850000;02;InitMsgNo [response] SA200CMD;Res;850000;010;InitMsgNo 4-11-23. Reboot ● Definition : reboot unit. Field Definitions Unit Remark CMD_ID “Reboot” Reboot device. <example> [command] SA200CMD;850000;02;Reboot [response] SA200CMD;Res;850000;010;Reboot 4-11-24. Request SIM IP Address ● Definition : Request of the local IP address in SIM card. Field Definitions Unit Remark CMD_ID “ReqSIMIP” SIM card IP request <example> [command] SA200CMD;850000;02;ReqSIMIP [response] SA200CMD;Res;850000;010;ReqSIMIP;172.16.18.6
ST300 User Manual 27 3. Installation 3.1 Insert SIM card. 3.2 Assemble as below Event Cable Color pin Description
ST300 User Manual 28 Red: VCC (12V) Black: Ground White: Input1. Panic Button When Input1 goes to GND, then ST300 change Emergency mode. It reports emergency string by mode 1 in Emergency mode such that SA200EMG;850000;20081017;07:41:56;00100;+37.478519;+126.886819;000.012;000.00;9;1;0;15.30; 110000;1 Orange: Output1. Immobilizer activation behaves progressive blocking when vehicle is driving. The progressive blocking diagram is as below. The active time of the immobilizer increases 90ms each 4s. After 3minutes, immobilizer is activated continuously. When one of output is dedicated to PULSE, it operates as below. Time for activation and deactivation is configurable by PULSE_ON and PULSE_OFF in Service Parameter. Pulse time may have tolerance about dozens of milliseconds. Active and inactive state is decided by output line number. Active state of Output 1 is open(Hi-Z) and active state of output 2 is ground. 3.6 Check GPS/GPRS operation and battery charger operation with LEDs. It takes 3~10 minutes for GPS connected. Caution: Direction of ST300 is very important when installed in the vehicle. Make sure that top side of ST300
ST300 User Manual 29 4. Trouble Shooting (LED Indicator) 4.1 Blue LED: Indicates GPRS status. GPRS Blink Count Remarks Normal 1 Server Com. Error 2 <Possible Cause> 1. Server or network parameter is wrong. 2. Server is closed. 3. Temporary network barrier GPRS Com. Error 3 <Possible Cause> 1. Network parameter is wrong. 2. SIM is blocked about GPRS using. 3. Temporary network barrier 4. Weak GPRS signal 5. GPRS antenna connection is not firm. No Network 4 <Possible Cause> 1. GPRS antenna is disconnected. 2. GPRS antenna or socket of GPRS antenna is broken. 3. Device is broken. SIM PIN Locked 5 <Possible Cause> 1. SIM PIN is enabled. Cannot Attach NW 6 <Possible Cause> 1. Weak GPRS signal. 2. GPRS antenna connection is not firm. No SIM 7 <Possible Cause> 1. There is no SIM or SIM is not inserted properly. 2. SIM or SIM socket is broken.
ST300 User Manual 30 4.2 RED LED: Indicates GPS status. GPS Blink Count Remarks Normal 1 No Fix 2 <Possible Cause> 1. If power on, GPS chipset is trying to find position during some minutes. 2. GPS antenna lays on weak or no GPS signal position 3. GPS antenna connection is not firm. GPS Chipset Error GPS Antenna Error 4 <Possible Cause> 1. GPS antenna is disconnected. 2. GPS antenna or socket of GPS antenna is broken. 3. Unit is broken. The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. Cautions Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ST300 User Manual 31 NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu