Superior Electronics 919TB4H Hand Held Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	396578
Application ID	jieDAgq7fSbsItw2P/VZsA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.77kB (147107 bits)
Date Submitted	2004-02-13 00:00:00
Date Available	2004-02-12 00:00:00
Creation Date	2004-02-06 14:12:31
Producing Software	Acrobat 5.0 Scan Plug-in for Windows
Document Lastmod	2004-02-06 14:14:14
Document Title	User Manual
Document Creator	Acrobat 5.0 Scan Plug-in for Windows

Typical Applications:
Positive Output: IZVDC receiver puller driving a mnc appliance:
— Positive Power Source =OM
NC
— Positive Power Output 12VDC O/P
} Power tor SK-B IORZ 12VD C Power for SK-910R2
lZilllC receiver power input. 24m: output driving a motor
24VAC(1) Input
24VAG(1) Out-ut
——G"°
_ +lZVDC
— Negative Power Output
} Power tor SK-910R2
General Specifications
Operating Frequency: 31's MHz
Memory Capacity:
Operating Voltage:
Operating Current:
15 transmitter button codes per channel
TIVDC ~ 24VDC or ”VAC ~ 24VAC
3 mA @ 12VDC (standby)
30mA/channel @ lZVDC (activated)
Relay Contact Rating: Form 'C' type, 10A @ 24VDC or lZOVAC per channel
Connectors: Screw Terminals, +, —,
with N/O, N/C, and COM per channel
Dimensions: 3.25" x 2.7” x 1.1" (83 x 68 x 27.5 mm)
MODEL: 5K-9I 9TBAH-N
FCC ID : K4E919TBAH
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS: (I ) THIS DEWCE MAY NOV CAUSE
HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY (MUSE UNDESIRED OPERATION
IMPORTANT NOTES:
a) The changes or rltoditicaiions not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
b) To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could
result in the device exceeding the RF exposure requirements and void user's authority
to operate the device,
The secounm policy is one cl conlinual development and improvement
For this reason. SECO~LARM reserves the right to change specifications without runner nottcet
SECO-lARM‘ U.S.A, INC. Telephone Fax
16342 Millikan Avenue (800) 662-0800 (949) 261-7326
lrvine, CA 92606 (949) 261-2999
ms rE—w. c mmmwAth/Ksmnwe Pas ocrzoor
onnsn mm per
ENFORCER®
SK-9‘l 0R2 RECEIVER
with
SK-9'I 9TB4H-N TRANSMITTER
SLI®
SECO-I..ARM‘E
System
The SK—SIORZ RF receiver are compatible with both code hoppirg and tired-code transmitters. They can be used
tor a variety of applications, such as allowing the saute transmitter to ann/disann a vehicle alarm and open/close a
garage door opener. The SK-OIORZ receiver has twoahannel outputs. Each channel can learn the codes at up to
15 ditterent transmitter buttons on a hrst»rn, tirst-out basis.
Installation Notes
1. Mount out of siflrt in a location where it is not sumrunded by metal, and where it is not exposed to the
weather or moisture. Metal will block the Rt signal, resulting in a reduced range.
2, For best ram. pull the antenna wire as long and straight as possible. it the receiver receives intertererrce
from local Rf activity (cg, airport or military base), the antenna wire can be folded. DO NOT CUT THE
ANTENNA WIRE.
Learning a New SK-9l 9TB4H-N Button Code
1. To learn a transmitter code for channel 1, press mode switch #I tor three seconds. The green ID will start
to flash quickly.
2. While the green lED is flashing quickly, press any desired button on the compatible SK—919TBAH-tl
transmitter The green LED will flash once and then trim Mt to show that that btnton was learned.
3. Repeat steps 1 and 2 to learn more buttons into channel 1.
NOTE — The green LED will flash 1 maximum at 15 seconds. lt no transmhter button is pressed during this time,
the recewer will out the codeleaming mode and the green LED will turn oil
4 To learn a new SK— 919TBlH ll transmitter button tor channel 2, the pmcedure rs the same as tor channel 1,
arcept mode switch #2 initiates the codeleaming process, and the red LED shows status.
Note Regarding Code Learning
1, The receiver will only learn the code at a particular button once. Once a button’s code is teamed, rlyou try to
code~learn that button again, whether it is tor the same channel or not, the receiver will exit code teaming mode.
2. Each channel can learn the codes of a maximum of 15 transmitter buttons. it you attemptto learn a sixteenth ,
button. the earliest code learned will be delemd.
3. To clear all codes— Press the appropriate mode switch (#1 or #2) forthree seconds. When the LED starts
hashing, press that switch again tor three seconds. The LED hashes hnicelo indicatethatall codes associated
witlr that channel are now deleted.
Programming Relay Output Modes
The relay outputts) can be progranuned torone ot tour different modes depending on the application:
4 second momerrtary~ Press the transmitter button once. The relay toms on tor 4 seconds, and then turns oil.
(This is the DEFAULT mote)
0 1- second momeritary— Press the transmitter button once. The relay turns on tor I second, and ttrerr turns all.
0 Toggle — Press the transmitter button ohce, and the relay turns on. Press a compatible transmitter button again,
and the relay tums oft
- Latch — Press the trantmhter button once. and the relay tums on and stays on. The relay will rerrrain on until ore
appropriate mode switch (#I or #Z) is pressed to reset regardless of whether a compatible transmitter button
is pressed again or not.
To program outputs, open case and find the Ziumpers marked LPl and LPZ, Cut these jumpers, it needed, as tollows:
Output type LPl LP2
4-second momentary Uncut Uncut
1-second momentary Uncut Cut
Toggle Cut Uncut
Latch Cut Cut
NOTE 7 The output mode of both relays is the same. In other words, you cannot have 4-sacond momentary
output tor channel 1 and latch output tor channel 2.
MODE SWITCH #1
I M0
Antenna Program Loop
(see Extended Range Antennas below)
Three-Pin Antenna Port
(see Extended Range Anmnnas below)
Output Program Loops
Outouttype rrr rra
e-seormd momentary Uncut Uncut
l~secorrd momentary Uncut Cut
Toggle Cut Uncut
Latch Cut Clll
CH 2 DRY RELAY COM
CH 2 DRY RELAY ttC
CH 2 DRY RELAY ”0
CH 1 DRY RELAY COM
CH 1 DRY RELAY NC
CH 1 DR! RELAY NO
GND
+ 11-24VDC
CH 2 STATUS LED
CH 1 STATUS LED
Mode Switch Operation (one per channel)
- Learn mode —' Press and hold the switch tor three seconds.
~ Clear manory — Press three seconds, then when the LED stem tlashing press again tor three seconds to
' delete all previously learned codes.
- Reset latched output — lt this channel was programmed for latch output once the relay is trrmed on with a
transmitter button, press the mode switch to him the relay oil.
~ Memory Display ~ Press and release the mode switch to show number ot codes stored, LED will trash a number
at times to correspond to the number of codes stored.
LED lndication (one per channel)
- Steady on 7 Senses signal from a transmitter button whose code was already teamed.
- Fast tlash — tn the code-teaming rnode.
- One flash ~ A transmhter button code was teamed.
- Two tlasheszll previously learned
transmitter button codes were deleted.
stl-Olllllllltll Four-Button, thannel transmitter
- Over 68 billion (6. 8 x IO”) possible codes
- LED transmission indicator.
0 lncludes visor clip and 3VDC lithium battery (2 pcs).
- slrm- line design
' Size: 3‘/r" x Z’lrs' X V1", (88 x 55 x 12 mm).

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2004:02:06 14:14:14+08:00
Create Date                     : 2004:02:06 14:12:31+08:00
Creator                         : Acrobat 5.0 Scan Plug-in for Windows
Page Count                      : 2
Mod Date                        : 2004:02:06 14:14:14+08:00
Creation Date                   : 2004:02:06 14:12:31+08:00
Producer                        : Acrobat 5.0 Scan Plug-in for Windows
Metadata Date                   : 2004:02:06 14:14:14+08:00

EXIF Metadata provided by EXIF.tools