Superior Electronics 919TDWS Remote Control Transmitter User Manual MiSK9x9TDWS BQfcc 1508

Download:
Mirror Download [FCC.gov]
Document ID	2809863
Application ID	Mqnx17R4dhzCrhn9pcPb/w==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.69kB (271155 bits)
Date Submitted	2015-11-11 00:00:00
Date Available	2015-11-11 00:00:00
Creation Date	2015-08-05 17:00:52
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2015-11-10 21:52:05
Document Title	Microsoft Word - MiSK9x9TDWS-BQfcc_1508
Document Creator	PScript5.dll Version 5.2.2
Document Author:	vlee

INSTALLATION:
Installation Manual
SK-919TDWS-BQ
Wired Single-Channel RF Transmitter
FEATURES:
• Powered by internal battery or external 12VDC
output regulated adapter
• Frequency 315 MHz
• Over 68 billion (6.8x1010 ) possible codes
• LED transmission indicator
• Includes one 12VDC alkaline battery
• Compatible with all SECO-LARM receivers
• Compact size 2” x 1.5” x 0.59” (50x38x15 mm)
• Wiring: Two, 6-inch blue wires for N.O. switch
input
Two, 6-inch wires (red & black) for
12VDC power input
SK-919TDWS-BUQ
same as SK-919TDWS-BQ,
•
but no logo
Compatible Receivers:
SK-910RQ
1-Channel
SK-910R2Q
2-Channel
SK-910R4Q
4-Channel
1.) Power Connection – The wired transmitter can be powered by the factory preinstalled one
12VDC alkaline battery or by an external 12VDC output regulated adapter (not included).
If an external power adapter is preferred, connect the red & black wires of the wired transmitter
to the adapter’s output wires. Must observe correct wire polarity. Red wire is for positive
and black wire is for negative.
NOTE: a) The power input range of the wired transmitter unit is between 9~13.8VDC, connecting
more than 13.8VDC power or reversing the polarity will burn out the unit and void the
warranty.
b) Use only 12VDC output “regulated” adapters to power the wired transmitter.
c) Factory had preinstalled one 12VDC alkaline battery inside wired transmitter unit. If it
is necessary to connect an external adapter, removed first the internal alkaline battery,
otherwise the internal battery will become defective.
2.) External Switch Connection – Aside from its own built-in single button, the wired transmitter
can also be controlled by an external N.O. pushbutton / sensor switch (not included), or use
both the built-in & external switches (see Example Connection Diagram below). If an
additional external N.O. switch is necessary, connect the two blue wires to the switch terminal.
NOTE: If the red & black or the two blue wire pairs are not being use, the tip of the wires (where
the copper wires are exposed) must be cut or wrapped to avoid a short circuit.
Example Connection Diagrams:
TYPICAL APPLICATIONS:

 Make any push-to-exit plate wireless

 Convert Dual-Beam sensors with dry
contacts into entry alert system

 Wireless equipment / perimeter
security

 Wireless doorbell / Service call button
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in
normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or
the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
Fax: 949-261-7326
File: VL/DTP/Manual/MiSK9x9TDWA-BQfcc_1508.doc
Order Part #762-103-2%fcc
PITSW1
Website: www.seco-larm.com
E-mail: sales@seco-larm.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : vlee
Title                           : Microsoft Word - MiSK9x9TDWS-BQfcc_1508
Create Date                     : 2015:08:05 17:00:52
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2015:11:10 21:52:05+08:00
Metadata Date                   : 2015:11:10 21:52:05+08:00
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:c3055fd3-c581-477c-9962-e49d732cb806
Instance ID                     : uuid:6c4d6d74-99c2-42e0-b88f-b47cfe042fcf
Page Count                      : 1
Author                          : vlee

EXIF Metadata provided by EXIF.tools