Superior Br 42 Users Manual B42 (700,026M) NC 01/01

2014-12-11

: Superior Superior-Br-42-Users-Manual-121532 superior-br-42-users-manual-121532 superior pdf

Open the PDF directly: View PDF .
Page Count: 20

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1

42" Wood Burning Fireplaces

P/N 700,026M REV. C 11/2003

BR-42 BC-42

BRI-42 BCI-42

BR-42-2 BC-42-2

MODELS

WH Report No. J99025865B-231

STANDARD SERIES

This installation manual will enable you to obtain a safe, efficient and

dependable installation of your fireplace system. Please read and under-

stand these instructions before beginning your installation.

Do not alter or modify the fireplace or its components under any

circumstances. Any modification or alteration of the fireplace system,

including but not limited to the fireplace, chimney components and

accessories, may void the warranty, listings and approvals of this system

and could result in an unsafe and potentially dangerous installation.

IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS:

INSTALL THIS FIREPLACE IN A SQUARE AND PLUMB CONDITION,

USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION

INSTRUCTIONS

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

TABLE OF CONTENTS

Safety Rules .................................... page 2

Tools and Building Supplies ............ page 2

Precautions ..................................... page 3

Introduction ..................................... page 3

Clearances/Height Requirements..... page 3

Chimney System ............................. page 3

Assembly Outline............................. page 4

Location of Fireplace ....................... page 4

Assembly Steps ............................... page 5

Preinstallation Notes........................ page 5

Clearances ....................................... page 5

Installing the Fireplace ..................... page 5

Fireplace Specifications .................. page 6

Framing Specifications.................... page 7

Installing the Chimney System ........ page 8

30° Offset through Floor/Ceiling ...... page 9

Ten Foot Rule Summary .................. page 11

Multiple Terminations ...................... page 11

Chimney Component Calculations ... page 11

Special Offset Instructions............... page 12

Offset Calculations........................... page 12

Vertical Elevation Chart ................... page 12

Offset Elevation Chart ..................... page 13

Installing Offsets.............................. page 14

Optional Equipment Considerations. page 14

Forced Air Kits ................................. page 14

Combustion Air Kits ........................ page 15

Gas Line Connection........................ page 15

Vent Free Appliances ....................... page 15

Glass Doors ..................................... page 16

Cold Climate Insulation.................... page 16

Fireplace Finishes ............................ page 16

Mantels and Trim............................. page 16

Hearth Extensions/Wall Shields ....... page 16

Finish Requirements ........................ page 18

Installation Components .................. page 18

IMPORTANT: PLEASE READ AND

UNDERSTAND THESE RULES TO

FOLLOW FOR SAFETY.

1. Before starting your fireplace installation,

read these installation instructions carefully to

be sure you understand them completely and in

entirety. Failure to follow them could cause a

fireplace malfunction resulting in serious injury

and/or property damage.

The manufacturer is not responsible for any

smoking or related problems that may result

from the lack of adequate combustion air. It is

the responsibility of the builder/contractor to

ensure that adequate combustion air has been

provided for the fireplace.

13. DO NOT use a fireplace insert or any other

products not specified herein by the manufac-

turer for use with this fireplace. All gas log sets

must be operated with the damper clamped

open, including unlisted “vent free” log sets.

Listed “vent-free” log sets may be operated

with the damper closed.

14. "Smoke free” operation is not warranteed

nor are we responsible for inadequate system

draft caused by mechanical systems, general

construction conditions, inadequate chimney

heights, adverse wind conditions and/or un-

usual environmental factors or conditions be-

yond our control.

15. Never, under any circumstances, install a

fireplace, chimney component or any acces-

sories, that has visible or suspected physical

damage as a result of handling or transporta-

tion. These items should be inspected by your

distributor or qualified factory representative

to ensure safe condition. When in doubt, con-

sult your distributor.

16. For additional safety considerations and

complete operating instructions, refer to the

Care and Operation Manual provided with the

fireplace.

TOOLS AND BUILDING SUPPLIES

NORMALLY REQUIRED

Tools should Include:

Phillips screwdriver

Hammer

Saw and/or sabersaw

Level

Measuring tape

Plumb line

Electric drill and bits

Pliers

Square

Building supplies:

Framing materials

Wall finishing materials

Caulking materials (noncombustible)

Fireplace surround and hearth

extension materials (noncombustible)

2. Always check your local building codes. The

installation must comply with all local, regional,

state and national codes and regulations.

3. These fireplaces must be installed with

Security Chimneys FTF8 (8" inside diameter)

Chimney System only. These systems are in-

tended for use in any application where a

traditional masonry type fireplace would ap-

ply. The chimney system must always vent to

the outside of the building.

4. To ensure a safe fireplace system and to

prevent the build-up of soot and creosote,

inspect and clean the fireplace and chimney

prior to use and periodically during the heating

season.

5. Use solid fuel only. DO NOT use artificial

wax based logs, chemical chimney cleaners or

flame colorants in your fireplace.

6. DO NOT use charcoal or coal under any

circumstances.

7. NEVER use gasoline, gasoline-type lantern

fuel, kerosene, charcoal lighter fluid, or similar

liquids to start or “freshen up” a fire in this

fireplace. Keep any flammable liquids a safe

distance from the fireplace.

8. NEVER leave children unattended when

there is a fire burning in the fireplace.

9. Always keep flue damper open when heat is

present in the fireplace.

10. Before servicing, allow the fireplace to

cool. Always shut off any electricity or gas to

the fireplace while working on it. This will

prevent any possible electrical shock or burns.

11. This fireplace is not intended to heat an

entire home or be used as a primary heat

source. It is designed to ensure homeowner

comfort by providing supplemental heat to the

room.

12. Always ensure an that adequate supply of

replacement combustion air from the outside

of the house is accessible to the fire to support

normal combustion. Fireplaces consume large

volumes of air during the normal combustion

process. In the event the home is tightly sealed

with modern energy efficient features, the op-

tional combustion air kit may not provide all

the air required to support combustion.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3

Figure 1

TYPICAL INSTALLATION

*Construction Materials:

• framing materials • paneling

• particle board • flooring

• millboard • dry wall

• plywood • etc.

PRECAUTIONS

Note: These fireplace systems are not difficult

to install. However, in the interest of safety, it

is recommended that the installer be a quali-

fied or certified “tradesman” familiar with com-

monly accepted fireplace installation and safety

techniques as well as prevailing local codes.

The most important areas of concern dealing

with the installation of factory-built fireplaces

are clearances to combustible materials, proper

assembly of component parts, height of the

chimney system, the proper use of accesso-

ries supplied by the manufacturer and the

techniques employed in using finishing mate-

rials applied to the wall surrounding the fire-

place, hearth extensions and wall shields. Each

of these topics will be covered in thorough

detail throughout this manual. Please give

each your special attention as you progress

with your installation.

INTRODUCTION

General Information

These fireplaces are conventional radiant heat

fireplaces with standard bar grates, optional

outside combustion air kits and optional deco-

rative glass doors.

Note: Illustrations shown reflect “typical” in-

stallations with nominal dimensions and are

for design and framing reference only. Actual

installations may vary due to individual design

preferences. However, always maintain mini-

mum clearances to combustible materials and

do not violate any specific installation require-

ments.

These fireplaces have been tested and listed by

Warnock Hersey (Report No. J99025865B-231)

to U.L. standard 127. These units are intended

for installation in residential homes and other

buildings of conventional construction includ-

ing commercial, not in mobile homes.

These fireplaces have been tested for installa-

tion in Canada to ULC-S610. For installations

in Canada, the chimney clearance to com-

bustibles must be 2 inches and the Cold

Climat Kit must be installed.

These fireplace systems are designed for in-

stallation in accordance with the National Fire

Protection Standard for chimneys, fireplaces

and solid fuel burning appliances; NFPA 211

and in accordance with codes such as the

BOCA Basic/National Codes, the Standard Me-

chanical Code and the Uniform Building Codes.

When complete these fireplace systems con-

sists of five basic “sub-systems”:

1. The Fireplace

2. The Chimney and Termination

3. The Optional Glass Doors

4. The Optional Combustion Air Kits

5. Optional Cold Climate Kit (Mandatory in

Canada).

CLEARANCES AND HEIGHT

REQUIREMENTS

The fireplace may be placed on or near normal

construction materials*. The combustion air

kit, firestop spacer and roof flashing (not chase

flashings) may be placed directly on or against

normal construction materials.* The chimney

and fireplace outer wrapper require a mini-

mum 1"** air space to combustibles. A com-

bustible mantle may be installed 12" above the

opening of the fireplace as per NFPA 211,

Section 7-2.3.3 (1992). In Canada, the mini-

mum is 18" above the fireplace opening.

The minimum installed height of the completed

fireplace system is 15' 0". The maximum height

is 60' 0".

The fireplace and chimney system must be

enclosed when installed in or passing through

a living area where combustibles or people may

come in contact with it. This is important to

prevent possible personal injury or fire hazard.

For questions, please call your distributor or

the manufacturer. Special restrictions apply to

the front and facing of the fireplace and nearby

walls (See pages 16, 17 and 18 ).

CHIMNEY SYSTEM

These fireplaces are designed and code listed

for use with Security Chimneys FTF8 chimney

System only. Always use Security Chimneys

FTF8 chimney components with these fire-

places. Do not modify or alter these compo-

nents as this may cause a potential serious

hazard and void the Warranty.

**Note: 2" clearance to combustibles around

chimney components required in Canada.

WARNING: MODELS THAT HAVE THE

"-2" SUFFIX HAVE NOT BEEN TESTED

WITH AN UNVENTED GAS LOG SET. TO

REDUCE RISK OF FIRE OR INJURY, DO

NOT INSTALL AN UNVENTED GAS LOG

SET INTO THIS FIREPLACE.

Outside

Combustion

Air Kit

(Optional)

Chimney and

Termination

Radiant Model Shown

The "C" models are designed as heat circulating

fireplaces and may be fitted with accessory

fans.

The BRI and BCI models are fully insulated for

installation in colder climates.

WARNING: FAILURE TO USE MANUFAC-

TURE PROVIDED PARTS, VARIATIONS

IN TECHNIQUES AND CONSTRUCTION

MATERIALS OR PRACTICES OTHER THAN

THOSE DESCRIBED IN THIS MANUAL

MAY CREATE A FIRE HAZARD AND VOID

THE LIMITED WARRANTY.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

WARNING: IF INSULATION IS USED, THE

FIREPLACE MUST NOT BE PLACED DI-

RECTLY AGAINST IT. INSULATION OR

VAPOR BARRIERS, IF USED, MUST FIRST

BE COVERED WITH GYPSUM BOARD,

PLYWOOD, PARTICLE BOARD OR OTHER

MATERIAL TO ASSURE INSULATION AND

VAPOR BARRIERS REMAIN IN PLACE.

Figure 2

Chimney Height

The total height of your completed fireplace

system from the surface the fireplace rests on

to the chimney top must not exceed 60' and

must also meet minimum height requirements.

Refer to the minimum system height chart.

LOCATION OF FIREPLACE

Carefully select the proper location for heat

circulation, aesthetics, chimney obstructions

and clearance to side wall(s). With proper pre-

planning, a slight adjustment of a few inches

can save considerable time and expense later

during construction and assembly.

Figure 4

Carefully consider the position of the fireplace

opening with respect to the location of adja-

cent or nearby stairwells, bath or kitchen ex-

haust fans and/or return air registers for forced

air furnaces/air conditioners that could cause

a smoking fireplace condition if the house is

tightly insulated.

When locating the fireplace, consideration must

be given to combustibles and final finishing.

See

Figure 5

and confine the final location of

combustible finish materials to the "Safe Zone".

DO NOT permanently place furniture or other

items such as decorative pillows within 60" of

the fireplace front face.

Insulate Joists

Same As Ceiling

Draft Stops

Firestop

CTDT

Termination

Note: Non-

Combustible

Chase

Flashing

Must Be

Used To

Cover

Chase

Opening

Optional

Insulation

In Outside

Walls Of

Chase

Solid

Continuous

Surface

Outside

Base

Insulation

(Thermal Barrier)

Level

Chase Enclosure

A chase is a vertical box-like structure con-

structed to surround the fireplace and chimney.

Refer to

Figure 2

for a typical chase configura-

tion. As with all chimney installations, avoid

overhead obstructions such as trees, power

lines, etc. A chase should be constructed and

insulated just like any outside wall. In a cold

climate, we recommend the base of the chase

should also be insulated between the solid

continuous floor beneath the fireplace and the

chase bottom. Chase insulation in a cold cli-

mate installation is not required for safety.

ASSEMBLY OUTLINE

Before You Start

Check your inventory list to be sure you have all

the necessary parts supplied in good usable

condition. Check also for any concealed damage.

Check the operation of the damper. The damper

is controlled through the use of a control lever

located within the firebox opening at the top

center in front of the firebox lintel (

Figure 3

The control lever snaps into place at either

extreme of its range of motion. When locked

in position all the way to the right, the damper

is open. When locked in position all the way to

the left, the damper is closed.

Figure 3

Note: Do not insulate the chase cavity with

blown or fill type insulation materials.

Note: Local codes may not require firestopping

at the ceiling levels for outside chase installa-

tions. However, it is recommended for safety

and the reduction of heat loss.

WARNING: DO NOT PACK OR FILL RE-

QUIRED AIR SPACES WITH INSULATION

OR OTHER MATERIAL. NO MATERIAL IS

ALLOWED IN THESE AREAS.

Damper

Closed Damper

Open

Lintel

Combustion

Air Actuator

Figure 5

Hearth

Optional

Outside Chase

Wall

Covering

Black Portion Of Frame

Not To Be Covered With

Combustible Materials

Safe

Zone

45°

12”

Door

Opening

1”

Security's FTF8 Pipe

Vertical Installation 15' 0"

One Offsets 15' 0"

Two Offsets 25' 0"

Minimum System Height

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5

Note: Install the hearth extension only as illus-

trated.

The safety strips should extend from front of

the fireplace at least 1 ¹⁄₂" and should extend to

be at least flush with the sides. In the event a

wooden support is used to elevate the fireplace

above the floor, a “Z” type safety strip should be

fabricated and used to protect the front surface

of the wood support as well as the floor beneath

the hearth extension (

Figures 8 and 9

). The

safety strips should be tacked down to prevent

possible movement.

Note: The “Z” type safety strip is not supplied.

1. Estimate the total weight of the fireplace

system including chimney and surround ma-

terials such as brick, stone, etc., to be in-

stalled. Shipping weights for the fireplace

may be found on page 18.

2. Measure the square footage of the floor

space to be occupied by the system, surrounds

and hearth extensions.

3. Note the floor construction, i.e. 2 x 6’s, 2 x 8’s

or 2 x 10’s, single or double joists, type and

thickness of floor boards.

4. Use this information and consult your local

building code to determine if you need addi-

tional support.

CAUTION: DO NOT BLOCK THE HEAT-CIRCU-

LATING AIR INLET AND OUTLET PORTS ON

CIRCULATING MODELS. DOING SO MAY RE-

SULT IN A POTENTIAL FIRE HAZARD.

If you plan to raise the fireplace and hearth

extension, build the platform assembly then

position fireplace and hearth extension on top.

Secure the platform to the floor to prevent

possible shifting.

CLEARANCES

Minimum clearance to combustibles for the

appliance is as follows: sides and back - 1" (25

mm), floor - 0" (0 mm), adjacent wall - 12" (305

mm), ceiling - 37 ¹⁄₂" (953 mm).

INSTALLING THE FIREPLACE

Step 1. Slide the fireplace into prepared fram-

ing or position fireplace in its final position and

frame later.

The fireplace may not be recessed into a com-

bustible floor. Maintain the floor to hearth clear-

ance established by the fireplace lower front

face.

Step 2. Insert the provided metal safety strips,

beneath the fireplace as illustrated (

Figures 6, 7

and 8

). The safety strips should overlap ¹⁄₂" for

continual coverage of the floor.

Note: Safety strips are not required when fire-

place rests on a noncombustible surface.

ASSEMBLY STEPS

Note: The following steps represent the normal

sequence of installation. Each installation is

unique, however, and might require a different

sequence.

1. Position firebox prior to framing or into

prepared framing.

2. Install the chimney system.

3. Connect house wiring to the fireplace for

later attachment of optional blower.

4. Install optional outside combustion air kit.

5. Plumb gas line if a decorative gas appliance

will be used. (Gas connections should only be

performed by an experienced, licensed/certi-

fied tradesman.)

6. Complete the installation, finish wall mate-

rial, surround and hearth extension to your

individual taste.

7. Assemble and attach optional glass door

assembly.

Study the three dimensional illustration (

Fig-

ure 1

) to get a general idea of each element of

your fireplace system.

PRE-INSTALLATION NOTES

The fireplace may be installed directly on a

combustible floor or raised on a platform of an

appropriate height. Do not place fireplace on

carpeting, vinyl or other soft floor coverings. It

may, however, be placed on flat wood, ply-

wood, particle board or other hard surfaces.

Be sure fireplace rests on a solid continuous

floor or platform with appropriate framing for

support and so that no cold air can enter the

room from under the fireplace.

The fireplace may be positioned and then the

framing built around it, or the framing may be

constructed and the fireplace positioned into

the opening.

Usually, no special floor support is needed for

the fireplace, however, to be certain:

Figure 7

Figure 6

1" (25 mm) Space

Metal Safety Strip Floor

Hearth

Extension

Maintain

1" (25 mm)

Air Space

At Back

And Sides

Top Spacer

Note: Hearth extensions must not interfere with

circulating grillwork

Metal Safety Strip Floor

Hearth

Extension

Platform

1" (25 mm) Space

Maintain

1" (25 mm)

Air Space

At Back

And Sides

Note: Hearth extensions must not interfere with

circulating grillwork

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

FIREPLACE SPECIFICATIONS

Figure 10

Figure 8

Figure 9

Step 3. Refer to fireplace drawings and specifi-

cations on pages 6 and 7 for framing dimensions

and details. Frame appliance enclosure as illus-

trated in

Figures 11 through 14

on page 8.

IMPORTANT: UNDER NO CIRCUMSTANCES

CAN THE FIREPLACE TOP SPACERS (

FIGURE

) BE REMOVED OR MODIFIED, NOR MAY

YOU NOTCH THE HEADER TO FIT AROUND OR

BE INSTALLED LOWER THAN THE SPACERS.

THE HEADER MAY BE IN DIRECT CONTACT

WITH THE TOP SPACERS BUT MAY NOT BE

SUPPORTED BY THEM.

Note: The framed depth, 20

⁵⁄₈

" (524 mm) from

a framed wall, must always be measured from

a finished surface. If a wall covering such as

drywall is to be attached to the rear wall, then

the 20

⁵⁄₈

" (524 mm) must be measured from

the drywall surface. It is important that this

dimension be exact.

If the appliance is to be elevated above floor

level, a solid continuous platform must be

constructed.

The header may rest on the top metal spacers,

but must not be notched to fit around them.

Consult all local codes.

45"

(1143 mm)

31 ⁹⁄₁₆"

(802 mm)

21 ¹⁄₄"

(540 mm)

8 ³⁄₁₆"

(208 mm)

Top View

Right Side

Gas Line

Access Junction

Box

Combustion

Air Inlet

9 ⁷⁄₈"

(251 mm)

43"

(1092 mm)

21 ¹⁄₄"

(540 mm)

43"

(1092 mm)

21 ¹⁄₄"

(540 mm)

Left Side

45"

(1143 mm)

Front

43"

(1092 mm)

7 ³⁄₁₆"

(183 mm)

41"

(1041 mm)

(51 mm)

12 ¹⁄₂"

(318 mm)

22 ⁵⁄₁₆"

(566 mm)

13 ⁷⁄₁₆"

(341 mm)

8 ³⁄₈"

(213 mm)

Fireplace Top Spacer

Fireplace

Top Spacer

Gas Line

Access 19"

(483 mm)

10"

(254 mm)

12 ¹⁄₂"

(318 mm)

47"

(1194 mm)

(25 mm)

38"

(965 mm)

Blocking

Metal Safety Strips

1 ¹⁄₂"

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7

FRAMING SPECIFICATIONS

Figure 11

Figure 12

Figure 13

Figure 15

Figure 16

Figure 14

Framing Dimensions

A46 ¹⁄₄" 1175 mm

B43 ¹⁄₂" 1105 mm

C33" 838 mm

D17 ¹⁄₂" 445 mm

E76 ¹⁄₄" 1937 mm

F38 ¹⁄₈" 968 mm

G21 ⁵⁄₈" 549 mm

H20 ⁵⁄₈" 524 mm

J53 ⁷⁄₈" 1368 mm

Framing Dimensions for Roof

FTF8 at 1" FTF8 at 2"

Pitch C D* C D*

0/12 14 ¹⁄₂" 14 ¹⁄₂" 16 ¹⁄₂" 16 ¹⁄₂"

(368 mm) (368 mm) (419 mm) (419 mm)

6/12 14 ¹⁄₂" 17" 16 ¹⁄₂" 19"

(368 mm) (442 mm) (419 mm) (483 mm)

12/12 14 ¹⁄₂" 21 ¹⁄₂" 16 ¹⁄₂" 23 ¹⁄₂"

(368 mm) (546 mm) (419 mm) (579 mm)

Inside Chase

Back Wall of Chase/Enclosure

Including Finising Materials if any

Rough

Framing Face

(Unfinished Shown)

FOAK Combustion

Air Kit

Outside Chase

Back Wall of Chase/Enclosure

Including Finising Materials

if any

Rough

Framing Face

(Unfinished Shown)

FOAK

Combustion

Air Kit - Optional

Note: All framing dimensions calcu-

lated for 1/2" dry wall at the fireplace

face. If sheathing the chase or finish-

ing with other thickness materials,

calculations will need to be made.

* Perpendicular to roof ridge

Corner Installation

Back Wall of

Chase/Enclosure

Including Finising

Materials

if any

Rough

Framing Face

(Unfinished Shown)

FOAK Combustion

Air Kit - Optional

Ceiling Framing

Roof Framing

Header

Fireplace Framing

(See Note)

Note: When Framing With 6” Studs Header Must

Be 17” (432mm) Higher. Use Security Chimney’s

OR15 Offset/Return Elbow To Recess The Chimney

Back 2 1/2” (64mm). Flat Frame Down To A False

Header At (B). Maintain Required Clearance To

Chimney At All Times.

Framing Dimensions for Ceiling

Flue Type A B

FTF8 Vertical 14 ¹⁄₂" 14 ¹⁄₂"

(368 mm) (368 mm)

FTF8 Vertical 16 ¹⁄₂" 16 ¹⁄₂"

at 2" (419 mm) (419 mm)

FTF8 Offset 30°14 ¹⁄₂" 25"

(368 mm) (635 mm)

FTF8 Offset 30°16 ¹⁄₂" 27"

at 2" (419 mm) (686 mm)

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Step 4. Fireplace should be secured to side

framing members using the full length nailing

tabs at the top and bottom of the fireplace front

face. Use 8d nails (

Figure 17

Note: The nailing tabs and the area directly

behind the nailing tabs are exempt from the

clearances described on page 5. Maintain at

least 1/2" clearance from the firebox wrapper to

the framing at the closest point of contact,

directly adjacent to the flange.

For Canadian Installations

A cold Climate Kit FTF8-CCK3-LD must be

installed. CCK3 kits are available from

FireCraft through your local dealer. Installer

must supply suitable length of 6" Diameter,

class "0" metallic air duct.

Proceed with Steps 5 through 8

Step 5. Install the Cold Climate Kit to the

fireplace following the instructions provided

with the kit, (

Figure 18

8d Nail

Figure 20

Step 3. Position appropriate firestop spacer at

ceiling and nail temporarily with two (2) 8d

nails. Use flat firestop spacer, Model F8FS-2, if

chimney penetrates ceiling vertically. If chim-

ney penetrates ceiling at 30° angle (offset chim-

ney), use 30° firestop spacer, Model F8FS30.

Use one nail on opposite sides to hold firestop

spacer in position. Nail permanently, using at

least two (2) more 8d nails, after chimney

sections have been assembled through the

firestop spacer and after any necessary adjust-

ments have been made. Firestop spacer must

be secured by at least four (4) 8d nails when

completely installed.

CAUTION: ALLOW MINIMUM 1"* CHIMNEY

AIR SPACE TO COMBUSTIBLE FRAMING MEM-

BERS THROUGHOUT VERTICAL OR OFFSET

CHIMNEY INSTALLATION.

A minimum 1"* air space must be reserved for

all combustible materials extending for any

continuous length surrounding the chimney.

*Note: 2" clearance to combustibles required

in Canada.

Reference

Figures 15 and 16

and charts Fram-

ing Dimensions for Ceiling and Roof, which

specify minimum ceiling and roof dimensions.

In new construction, to determine chimney cen-

ter line, use plumb line from roof or ceiling above

fireplace to center of flue collar on fireplace.

For remodeling, plumb to center of flue collar

from ceiling above, drive nail through ceiling

from below to mark position, then mark and cut

to passage from above ceiling (around nail)

(

Figure 20

). Then plumb from ceiling or roof

level directly above hole which has just been

completed.

Figure 18

Step 6. Connect the 6" (102 mm) Class 0 air

duct provided by installer, to the duct collar on

the fireplace and secure with two (2) screws

from the kit’s hardware package.

Step 7. Route the Class 0 air duct out the back

or side wall, up through the ceiling or floor

joists to an outside wall. The air inlet hood

should be located above snow level or above

any anticipated snow level, (

Figure 19

Note: If the fireplace is installed against an inside

wall, the class 0 air duct may be extended into a

ventilated attic space at least 18" (475mm) above

the attic floor. Secure the air inlet hood to a

vertical post with the inlet positioned downward.

Ensure that nothing blocks the hood opening.

This hood must never terminate higher than

three (3) feet below the termination.

Step 8. Cut or frame a hole through the outside

wall for the installation of the air inlet hood. A 6-

1/2" diameter hole is required. Feed the loose

end of the flexible duct through the hole and

attach to the collar on the air inlet hood using two

(2) screws from the kit's hardware package.

Insert the hood into the opening. Secure the inlet

hood in place with nails driven through the holes

in the flange. Seal with noncombustible water-

proof silicon type caulking.

INSTALLING THE CHIMNEY SYSTEM

Step 1. Before continuing, check the operation

of the damper, as described on page 4, (

refer to

Figure 3

Step 2. Using standard construction framing

techniques, construct opening for chimney route

up through the ceiling(s) and roof or through an

outside chase.

Framing must maintain adequate minimum air

space clearance at all times.

Install As Shown With

Opening In Downward

Position Do Not Block

Entrance

5 Foot Min. Height

From Outside

Ground Level

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9

Note: If there is a room above ceiling level,

firestop spacer must be installed on the bottom

side of the ceiling. If an attic is above ceiling

level, firestop spacer must be installed on top

side of ceiling joist (Figures 21 and 22 ).

Figure 21

Figure 22

CHIMNEY 30° OFFSET THROUGH FLOOR

OR CEILING

It may be necessary to assemble the chimney at

30° when passing through the floor or ceiling

area. Use the F8FS30 firestop spacer as shown

Figures 23 and 24

. Support the chimney at

floor or ceiling penetration with a FTF8 stabi-

lizer if distance of chimney below ceiling is 10'

or more. Maintain 1"* minimum air space to

combustibles from chimney sections.

*Note: 2" clearance to combustibles required

in Canada.

Firestop Spacer

Room Above

Firestop Spacer

Attic Above

F8FS30

Firestop Spacer

FTF8-S4 Stabilizer

1"* Min.

Air Space

30° Firestop

And Attic Above

10'

Max.

Attic Space

1"* Min.

Air Space

Figure 23

F8FS30

Firestop Spacer

FTF8-S4 Stabilizer

30° Firestop

And Room Above

10'

Max.

Room Above

1"* Min.

Air Space

1"* Min.

Air Space

Figure 24

For Canada Only

When installing the chimney system through

an open attic space, the attic shield assembly-

firestop spacer must be used (

Figure 25

). This

installation is required only for use in Canada.

Note: For Canadian installations, all chimney

installed outside the building must be constructed

with galvalume (outer sections only) effective

January 1, 1992. The appropriate model desig-

nations are located in the back of this manual.

Step 4.

Note:

Chimney sections are con-

structed with a unique locking tab design,

which ensures an immediate, tight assembly

between sections. Plan your chimney require-

ments carefully before assembly as chimney

is difficult to disassemble after installation. If

disassembled, the tabs might become dam-

aged. Be certain tabs are properly formed to

ensure locking tabs engage properly.

The Security Chimneys FTF8 chimney system

is a two piece chimney, which snap together

from the fireplace up. Start with the inner flue

section with the lanced end up, snap lock it in to

the matching collar on top of the fireplace. At all

subsequent joints, the upper flue section fits

into the preceding flue section. Each piece

snaps together by means of locking tabs (9

locking tabs per joint). Check each piece by

pulling up slightly from the top to ensure proper

engagement before installing the next section.

Figure 25

Open Attic Space

If the flue has been installed correctly, it will not

separate when you test it. Also, the inner flue

joint where each section is joined should be

tight and flat without gaps (

Figure 26

Outer pipe section installs in just the opposite

way; the lanced end goes down and each new

section goes OVER the outside of the previous

section installed (

Figure 27

Note: Assemble one component of chimney at a

time (inner section first, then outer section last)

before proceeding with the next complete section.

Continue to assemble the chimney up through

framed opening. Assemble just enough to pen-

etrate the roof flashing openings (

Figure 28

Always maintain 1"* minimum air space to

combustible materials and always check each

chimney joint (inner and outer) to ensure proper

engagement. Check vertical alignment of chim-

ney so that it projects from the roof in true

vertical position.

Figure 28

Locking

Tabs

(Lances)

1"* Min. Air Space

To Combustibles

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Next, slide roof flashing over extended chimney

section that previously has been installed above

the roof opening in Step 4. FTF8 flashings

require flashing spacers. Slide flashing all the

way down until the flashing base rests flat on

the roof (

Figure 30

). Again, check the vertical

position of the chimney and the 1"* minimum

air space to combustibles.

Figure 30

Note: Do not caulk or seal the ventilating

openings.

Step 7. Secure flashing by nailing along the

perimeter into roof using 8d nails. If shingled

roof, slide upper end and sides of roof flashing

under shingles (trim if necessary), seal the top

and both sides of the flashing to the roof with

roof caulking. Cover nail heads with roof caulk-

ing (

Figure 31

Step 8. The standard Security Chimneys FTF8

roof flashing assemblies include a storm col-

lar. Slide the storm collar over outer chimney,

rest on flashing spacers and align with top

surface of flashing. Insert tab in slot, pull tight

and bend tab back over slot. Seal storm collar

to outer chimney with roof caulking or mastic

around entire circumference of pipe. Also add

extra roof caulking to the tab/slot area to seal

completely against water penetration (

Figure

). Check all joints very carefully to ensure

no water intrusion can take place.

Locking Band

Mastic

Figure 32

Step 9. Security Chimneys locking bands,

Model FLB, may be required if the chimney

extends too high above the roof flashing. As a

general rule, if the chimney extends more than

6' above the roof flashing, the use of locking

bands is advisable to strengthen the chimney

assembly. Align the locking band at the chim-

ney joint. Locking bands wrap around pipe

joints equally covering the joints of both pipe

sections. Use the nut provided and TIGHTEN

snugly. Do not overtighten as this might dam-

age the chimney section (

refer to Figure 32

Note: If chimney extends more than 8' above

roof surface, guy wires are also recommended.

Use three (3) guy wires, attach to locking band

assembly, extend and secure to roof in a trian-

gular pattern (Figure 33 ). Guy wires are not

supplied by the manufacturer.

Roof Ridge

120°

Figure 33

Step 10. Using a FTF8-CTD Round Termination:

1. Hold the FTF8-CTD over top of last chimney

section (

see Figure 34

2. Center inner slip section in inner flue pipe-

slip down.

3. Center outer locking section over outer flue

pipe. Push down until locking tabs are firmly

engaged.

Security's chimney sections do not need to be

screwed together. Additional reinforcement is

not necessary except in certain offset condi-

tions (refer to page 14,

Figure 39

Step 5. The height of vertical chimney pipe

supported only by the fireplace must not ex-

ceed 30'. Chimney heights above 30' must be

supported by a Model FTF8-S4 stabilizer in-

stalled at 30' intervals.

Note: The Model FTF8-S4 adds 3" net effective

height to the total chimney system.

Install the Model FTF8-S4 stabilizer by fitting

inner section down into respective section of

proceeding flue pipe and locking outer stabi-

lizer section into place over the outer chimney

pipe. Position for proper clearance through

framed opening and nail straps securely (under

tension in “shear”) into place on framing. Use

8d nails. Attach successive lengths of chimney

pipe directly to stabilizer using same tech-

niques as described in Step 4 (

Figure 29

Note: Do not apply excessive pressure to any

subsequent chimney sections following the

stabilizer when installing. Ensure each subse-

quent chimney section is securely attached by

testing as noted in Step 4.

Step 6. Select the proper Security Chimneys

roof flashing based on pitch of roof. Use chart

below for selection:

Roof Pitch Model

Flat to 6/12 F8F6

6/12 to 12/12 F8F12

FTF8-S4 Stabilizer

*Note: 2" clearance to combustibles required

in Canada.

FTF8 Chimney

FTF8 Flashing

Flashing Spacers

Do Not Seal

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11

Figure 34

4. Pull up slightly on CTD to ensure locking joint

has firmly engaged.

Using a FTF8-CTDT Chase Termination:

Refer to specific installation instructions in-

cluded with the FTF8-CTDT chase termination

for clearance and installation details.

Using a FTF8-CT1 Chase Termination:

Refer to specific installation instructions in-

cluded with FTF8-CT1 chase terminations for

clearance and installation details.

Using a FTF8-CT2 Chase Termination:

Refer to specific installation instructions in-

cluded with FTF8-CT2 chase terminations for

clearance and installation details.

Note: It is recommended that all exterior ex-

posed metal fireplace components; such as ter-

minations, flashings, storm collars and/or flue

be painted with a premium quality, high tem-

perature, rust preventative paint designed for

metal. This is especially important when instal-

lations are made in abnormally adverse or corro-

sive environments; such as near lakes, oceans or

in areas with consistently high humidity condi-

tions. Consult the paint manufacturers instruc-

tions for proper preparation and application.

*Note: 2" clearance to combustibles required

in Canada.

TEN FOOT RULE SUMMARY

The minimum chimney height above the roof

and/or to adjacent walls and buildings is speci-

fied by all major building codes.

If the horizontal distance from the peak of the

roof is less then 10', the top of the chimney

must be at least 2' above the peak of the roof.

If the horizontal distance from the chimney

edge to the peak of the roof is more than 10' a

chimney height reference point is established

on the roof surface 10' horizontally from the

chimney edge.

CTD

Termination Chimney

Figure 35

The top of the chimney must be at least 2' above

this reference point. In all cases, the chimney

cannot be less then 3' above the roof at the edge

of the chimney.

The 2' in 10' rule is necessary in the interest of

safety but does not ensure smoke-free opera-

tion. Trees, buildings, adjoining roof lines, ad-

verse wind conditions, etc., may require a taller

chimney should the fireplace not draft properly

(

see Figure 35

MULTIPLE TERMINATIONS

If more than one termination is located in the

same chase or within the same general proxim-

ity, we suggest they should be separated in

distance at least 24" horizontally from flue cen-

ter to flue center and stacked or staggered

vertically at least 18" apart, from the termina-

tion of one smoke exit to the termination of

another smoke exit (

Figure 36

FTF8 CHIMNEY COMPONENT

CALCULATIONS

The minimum installed height of the com-

pleted fireplace system is 15' 0". The maxi-

mum height is 60' 0".

To determine the number of chimney sections

and chimney components required, follow

these steps:

1. Determine total vertical height of the fire-

place installation. This dimension is the dis-

tance from the surface the fireplace sets on

to the point where smoke exits from the

termination.

2. Determine the number of chimney compo-

nents required, except chimney sections. This

would include firestop spacers, stabilizers, roof

flashing, etc.

3. The effective heights of the components are:

The Fireplace = 42 ¹⁄₄"

FTF8-12 = 10 ¹⁄₄"

FTF8-18 = 16 ¹⁄₄"

FTF8-36 = 34 ¹⁄₄"

FTF8-48 = 46 ¹⁄₄"

FTF8-CTD Termination = 4"

FTF8-CT1 Termination = 12" to 18"

FTF8-CT2 Termination = 15" to 23"

FTF8-CTDT Termination = 12" to 18"

FTF8-S4 Stabilizer * = 3"*

* Required for every 30' of vertical chimney

and/or 10' of offset chimney.

CTD

18"

24" 24"

CTDT

Less Than 10'

Min

2' Min.

10' 3'

Min

Figure 36

This suggestion is provided in the interest of

better operation. If the terminations are located

too close to each other, smoke may migrate

from one flue into the other.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

FTF8 VERTICAL ELEVATION CHART

Height Of Number Of FTF8

Chimney Only Chimney Lengths

Inches Feet/Inches 12" 18" 36" 48"

Height Of Number Of FTF8

Chimney Only Chimney Lengths

Inches Feet/Inches 12" 18" 36" 48"

386 ¹⁄₂ 32 2 ¹⁄₂ 0108

390 ³⁄₄ 32 6 ³⁄₄ 2008

396 ³⁄₄ 33 0 ³⁄₄ 1108

404 ¹⁄₂ 33 8 ¹⁄₂ 0018

414 ³⁄₄ 34 6 ³⁄₄ 1018

416 ¹⁄₂ 34 8 ¹⁄₂ 0009

420 ³⁄₄ 35 0 ³⁄₄ 0118

426 ³⁄₄ 35 6 ³⁄₄ 1009

432 ³⁄₄ 36 0 ³⁄₄ 0109

437 36 5 2 0 0 9

443 36 11 1 1 0 9

450 ³⁄₄ 37 6 ³⁄₄ 0019

461 38 5 1 0 1 9

462 ³⁄₄ 38 6 ³⁄₄ 00010

466 ³⁄₄ 38 10 ³⁄₄ 0119

472 ³⁄₄ 39 4³⁄₄ 10010

478 ³⁄₄ 39 10 ³⁄₄ 01010

483 40 3 2 0 0 10

489 40 9 1 1 0 10

496 ³⁄₄ 41 4 ³⁄₄ 00110

507 42 3 1 0 1 10

508 ³⁄₄ 42 4 ³⁄₄ 00011

513 42 9 0 1 1 10

519 43 3 1 0 0 11

525 43 9 0 1 0 11

529 ¹⁄₄ 44 1 ¹⁄₄ 20011

535 ¹⁄₄ 44 7 ¹⁄₄ 11011

543 45 3 0 0 1 11

553 ¹⁄₄ 46 1 ¹⁄₄ 10111

555 46 3 0 0 0 12

559 ¹⁄₄ 46 7 ¹⁄₄ 01111

565 ¹⁄₄ 47 1 ¹⁄₄ 10012

571 ¹⁄₄ 47 5 ¹⁄₄ 01012

575 ¹⁄₂ 47 11 ¹⁄₂ 20012

581 ¹⁄₂ 48 5 ¹⁄₂ 11012

589 ¹⁄₄ 49 1 ¹⁄₄ 00112

599 ¹⁄₂ 49 11 ¹⁄₂ 10112

601 ¹⁄₄ 50 1 ¹⁄₄ 00013

605 ¹⁄₂ 50 5 ¹⁄₂ 01112

611 ¹⁄₂ 51 11 ¹⁄₂ 10013

617 ¹⁄₂ 51 5 ¹⁄₂ 01013

621 ¹⁄₂ 51 9 ¹⁄₂ 20013

627 ¹⁄₂ 52 3 ¹⁄₂ 11013

635 ¹⁄₂ 52 11 ¹⁄₂ 00113

645 ¹⁄₂ 53 9 ¹⁄₂ 10113

647 ¹⁄₂ 53 11 ¹⁄₂ 00014

651 ¹⁄₂ 54 3 ¹⁄₂ 01113

657 ¹⁄₂ 54 9 ¹⁄₂ 10014

663 ¹⁄₂ 55 3 ¹⁄₂ 01014

667 ³⁄₄ 55 7 ³⁄₄ 20014

673 ³⁄₄ 56 1 ³⁄₄ 11014

681 ¹⁄₂ 56 9 ¹⁄₂ 00114

691 ³⁄₄ 57 7 ³⁄₄ 10114

693 ¹⁄₂ 57 9 ¹⁄₂ 00015

697 ³⁄₄ 58 1 ³⁄₄ 01114

703 ³⁄₄ 58 7 ³⁄₄ 10015

709 ³⁄₄ 59 1 ³⁄₄ 01015

714 59 6 2 0 0 15

720 60 0 1 1 0 15

727 ³⁄₄ 60 7 ³⁄₄ 00115

738 61 6 1 0 1 15

739 ³⁄₄ 61 7 ³⁄₄ 00016

744 62 0 0 1 1 15

11 0 11 1 0 0 0

17 1 5 0 1 0 0

21 ¹⁄₄ 19¹⁄₄ 2000

27 ¹⁄₄ 23¹⁄₄ 1100

35 2 11 0 0 1 0

47 3 11 0 0 0 1

51 ¹⁄₄ 43¹⁄₄ 0110

57 ¹⁄₄ 49¹⁄₄ 1001

63 ¹⁄₄ 53¹⁄₄ 0101

67 ¹⁄₄ 57¹⁄₄ 2001

73 ¹⁄₄ 61¹⁄₄ 1101

81 ¹⁄₄ 69¹⁄₄ 0011

93 ¹⁄₄ 79¹⁄₄ 0002

97 ¹⁄₄ 81¹⁄₄ 0111

102 ¹⁄₂ 86¹⁄₂ 1002

109 ¹⁄₄ 91¹⁄₄ 0102

113 ¹⁄₂ 95¹⁄₂ 2002

119 ¹⁄₂ 911¹⁄₂ 1102

127 ¹⁄₄ 10 7 ¹⁄₄ 0012

137 ¹⁄₂ 11 5 ¹⁄₂ 1012

139 ¹⁄₄ 11 7 ¹⁄₄ 0003

143 ¹⁄₂ 11 11 ¹⁄₂ 0112

149 ¹⁄₂ 12 5 ¹⁄₂ 1003

155 ¹⁄₂ 12 11 ¹⁄₂ 0103

159 ³⁄₄ 13 3 ³⁄₄ 2003

165 ³⁄₄ 13 9 ³⁄₄ 1103

173 ¹⁄₂ 14 5 ¹⁄₂ 0013

183 ³⁄₄ 15 3 ³⁄₄ 1013

185 ¹⁄₂ 15 5 ¹⁄₂ 0004

189 ³⁄₄ 15 9 ³⁄₄ 0113

195 ³⁄₄ 16 3 ³⁄₄ 1004

201 ³⁄₄ 16 9 ³⁄₄ 0104

206 17 2 2 0 0 4

212 17 8 1 1 0 4

219 ³⁄₄ 18 3 ³⁄₄ 0014

230 19 2 1 0 1 4

231 ³⁄₄ 19 3 ³⁄₄ 0005

236 19 8 0 1 1 4

242 20 2 1 0 0 5

248 20 8 0 1 0 5

252 21 0 2 0 0 5

258 21 6 1 1 0 5

266 22 2 0 0 1 5

276 23 0 1 0 1 5

278 23 2 0 0 0 6

282 23 6 0 1 1 5

288 24 0 1 0 0 6

294 ³⁄₄ 24 6 ³⁄₄ 0106

298 ¹⁄₄ 24 10 ¹⁄₄ 2006

304 ¹⁄₄ 25 4 ¹⁄₄ 1106

312 26 0 0 0 1 6

322 ¹⁄₄ 26 10 ¹⁄₄ 1016

324 27 0 0 0 0 7

328 ¹⁄₄ 27 4 ¹⁄₄ 0116

334 ¹⁄₄ 27 10 ¹⁄₄ 1007

340 ¹⁄₄ 28 4 ¹⁄₄ 0107

344 ¹⁄₂ 28 8 ¹⁄₂ 2007

350 ¹⁄₂ 29 2 ¹⁄₂ 1107

358 ¹⁄₄ 29 10 ¹⁄₄ 0017

368 ¹⁄₂ 30 8 ¹⁄₂ 1017

370 ¹⁄₄ 30 10 ¹⁄₄ 0008

374 ¹⁄₂ 31 2 ¹⁄₂ 0117

380 ¹⁄₂ 31 8 ¹⁄₂ 1008

Step 2. Use “Height of Chimney Only” column

in The Vertical Elevation Chart to determine

combinations of chimney used above return

elbow to achieve desired heights. Reference

Components Effective Height Chart in vertical

elevation chart section.

4. Determine amount of chimney height re-

quired by subtracting total combined height of

all pre-selected components (fireplace and

chimney components from total desired height.)

Reference Vertical Elevation Chart and deter-

mine the number of chimney sections (quantity

and length) required.

SPECIAL OFFSET INSTRUCTIONS

To clear any overhead obstructions, you may

offset your chimney system using Security's

30° offset and return elbows. Use two elbows -

an offset elbow to initiate the offset and a return

elbow to terminate it. A 30° offset elbow, an-

gling in any direction, may be the first compo-

nent used off the top of the fireplace flue collar.

The offset and return elbows may be attached

together, or a section or sections of chimney

may be used between, but do not exceed 20' in

total length between elbows. If sections of pipe

exceed 10' between elbows, a chimney stabi-

lizer must be used at the midpoint (

Figure 37

The stabilizer support straps must be attached

under tension (in shear) to structural framing

members above. When two sets of elbows are

used, the maximum combined length of chim-

ney used between elbows cannot exceed 20'

(

Figure 38

). Example: If C1 = 10' then C2 cannot

exceed 10'.

If an offset exceeds 6' in length, each chimney

joint beyond the first 6' of offset to the return

elbow, must be secured by a No. 8 x ¹⁄₂" sheet

metal screw located at the underside of the joint

(

Figure 39

A ¹⁄₈" diameter hole must be drilled in the

chimney joint using a ¹⁄₈" diameter drill. Hole

should be drilled in center of joint overlap

(

Figure 40

). Be sure to drill only through the

outer chimney casting. Do not puncture the

inner flue.

Maximum offset of chimney system is 30°. Two

offsets must not be assembled to form a 60° offset.

However, two sets of offset and return elbows may

be used on a single flue system, provided the total

height of the system exceeds 25'.

Return elbow support straps must be securely

attached under tension (in shear) to structural

framing members above. Do not substitute a

FTF8-30 offset elbow in place of a FTF8-E30

return elbow.

OFFSET CALCULATIONS

Step 1. Use Offset Chart to determine amount

of horizontal offset (A) and height (B) for vari-

ous chimney section assemblies.

Step 3. Use Elevation Chart as job estimator

only. Add necessary firestop spacers and sta-

bilizers as required. Firestop spacers must be

used as shown in

Figures 23 and 24

and

stabilizers as shown in

Figure 29

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13

A B FTF8-ES30 Number of FTF8 Chimney Sections

Offset Height Offset/Return FTF8-S4

(Inches) (Inches) Elbow Stabilizer 12" 18" 38" 48"

415³⁄₄ 100000

924¹⁄₂ 101000

12 29 ³⁄₄ 100100

14 ¹⁄₄ 33 ¹⁄₂ 102000

17 ¹⁄₄ 38 ¹⁄₂ 101100

20 ¹⁄₄ 43 ³⁄₄ 100200

21 45 ¹⁄₄ 1 0 0010

22 ¹⁄₄ 47 ¹⁄₂ 1 0 2 1 0 0

25 ¹⁄₄ 52 ¹⁄₂ 1 0 1 2 0 0

26 ¹⁄₄ 54 ¹⁄₄ 101010

27 55 ³⁄₄ 100001

28 ¹⁄₄ 57 ³⁄₄ 1 0 0 3 0 0

29 ¹⁄₄ 59 ¹⁄₄ 100110

31 ¹⁄₄ 63 1 0 2010

32 ¹⁄₄ 64 ¹⁄₂ 101001

34 ¹⁄₄ 68 ¹⁄₄ 1 0 1110

35 ¹⁄₄ 69 ³⁄₄ 100101

37 ¹⁄₄ 73 ¹⁄₄ 100210

38 ¹⁄₄ 75 1 0 0 0 2 0

39 ¹⁄₄ 77 1 0 2110

41 ¹⁄₂ 80 ¹⁄₂ 101400

43 ¹⁄₄ 83 ³⁄₄ 1 0 1 0 2 0

44 ¹⁄₄ 85 ¹⁄₄ 100011

45 ¹⁄₄ 87 ¹⁄₂ 1 0 0 3 1 0

46 ¹⁄₄ 89 1 0 0 1 2 0

48 ¹⁄₄ 91 ¹⁄₂ 1 0 2 0 2 0

49 ¹⁄₄ 94 ¹⁄₄ 101011

50 ¹⁄₄ 95 ³⁄₄ 100002

51 ¹⁄₄ 97 ³⁄₄ 1 0 1 1 2 0

54 ¹⁄₄ 103 1 0 0 2 2 0

55 ¹⁄₄ 104 ¹⁄₂ 101002

56 ¹⁄₂ 106 ¹⁄₂ 1 0 2 1 2 0

58 ¹⁄₄ 109 ³⁄₄ 100102

61 ³⁄₄ 116 1 1 1 0 3 0

64 ³⁄₄ 121 ¹⁄₄ 110130

67 124 ³⁄₄ 112030

68 ³⁄₄ 128 1 1 0 0 1 2

70 130 1 1 1 1 3 0

73 135 ¹⁄₄ 1 1 0230

74 ³⁄₄ 138 ¹⁄₄ 110003

79 145 ¹⁄₂ 1 1 1 0 4 0

80 147 ¹⁄₄ 1 1 1 0 0 3

82 150 ³⁄₄ 1 1 0 1 4 0

82 ¹⁄₄ 152 1 1 0 1 0 3

Figure 38

Figure 37

OFFSET ELEVATION CHART

Stabilizer

20'

Max.

10' Max.

Offset

Elbow

Return

Elbow

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 43

HOUSE

WIRING

COVER PLATE

Replace Cover Plate

After Electrical

Hook-Up

POWER TO THE FIREPLACE

The Optional Blower Kit

Operates on 115 volt 60 Hz

150 watts AC

GROUND

WIRE

House Wiring Must Be Secured

With The Appropriate Electrical

Connector To The Fireplace

Convenience Outlet Wiring

Measure height to the ceiling from the top of

fireplace-dimension “B.” Use the appropriate

Offset Elevation Chart to find dimension “A.”

Mark point where you will drive your nail to

show the center point for your offset ceiling cut.

Step 2. Proceed by using the Straight Up Instal-

lation Instructions for cutting and framing ceil-

ing and roof openings.

Note: See Framing and Dimension Chart for the

sizes of the ceiling and roof openings. The size

of the roof opening varies with the degree of

pitch of the roof.

Offset Elbow Assembly

Offset elbows install the same as chimney

sections. First, snap the inner section INTO the

preceding inner section of flue. Check connec-

tion by pulling up slightly to ensure a tight fit.

Next, the outer sections snap lock OVER the

preceding outer section of chimney. Again,

check outer section by pulling up slightly to

ensure proper connection is made.

Return Elbow Assembly

Return elbows install the same way as round

terminations and stabilizers:

Step 1. Hold return elbow over top of last

chimney section.

Step 2. Center inner slip section into inner flue

pipe-slip down.

Step 3. Center outer-locking section over outer

chimney pipe. Push down until locking joint has

firmly engaged.

Step 4. Pull up slightly on return elbow to

ensure locking joint has firmly engaged.

Step 5. Secure support straps to framing

members by nailing under tension in sheer

(

Figure 42

Figure 39

Figure 40

Figure 41

Chimney

Section

Joints

No. 8 x 1/2" SMS

Screws Required At

Every Joint Past 6'

No Screws Required In

Joints For First 6' of Offset

Underside Of Chimney

Chimney Section (S)

FTF8-E30 Return Elbow*

FTF8-30 Offset Elbow* B

*Part of Offset/Return Package Model FTF8-ES30

Return

Elbow

Note: The return elbow assembly performs the

same function as a stabilizer. Consider this

when determining the need for a stabilizer.

Note: Do not apply excessive pressure to any

subsequent chimney section following return

elbow assembly when installing. Ensure that

each subsequent chimney section is securely

attached by testing as noted above.

OPTIONAL EQUIPMENT

CONSIDERATIONS

Blower Kits (Circulating Models Only)

Blower Kits model FBK-100/200 are available

for use with circulating models. The Blower

Kit can be installed prior to or after installation

of the fireplace.

When installing the FBK-100 Blower Kit, a

Blower Switch Kit (Model FUBSK) is required.

This switch kit allows for a unit mounted

blower switch to be used. The FUBSK is not

included and must be purchased separately.

The FBK-200 Blower Kit comes standard with

a wall mounted variable speed control switch.

Note: The fireplace must have provisions for

a wall mounted On/Off switch in order to install

the FBK-200.

THE FIREPLACE MUST BE WIRED TO THE

HOUSE ELECTRICAL SYSTEM AT THE TIME

OF INSTALLATION IN ORDER FOR THE OP-

TIONAL FANS TO OPERATE, (SEE

FIGURES

43 AND 44

Note: The utilization of fans will increase the

air flow around the firebox. However, only a

minimal increase in heat output should be

anticipated.

INSTALLING OFFSETS

First, review the Offset Elevation Chart and

Figure 41

for reference.

Step 1. Determine the offset distance where

chimney is to pass through the first ceiling-

dimension “A.” To find this point on your

ceiling, first determine the center point for a

vertical chimney following the instructions for

vertical installation.

Figure 42

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15

Figure 44

THIS FIREPLACE IS NOT INTENDED TO BE

USED AS A SUBSTITUTE FOR A FURNACE TO

HEAT AN ENTIRE HOME. USE FOR SUPPLE-

MENTARY HEATING ONLY.

The FBK-100/200 Blower Kits are design certi-

fied by Warnock Hersey for use with these

appliances.

Always check local building codes. Installation

of the FBK Blower Kits must comply with local

regulations as well as the National Electric

Code.

Combustion Air Kits

These appliances are equipped with an outside

(make-up) air door and integral actuator arm. If

the appliance is to be installed with an outside

air vent system, use only FireCraft Models

FAOK or FAOK-LD Combustion Air Kits. These

kits come complete with detailed installation

instructions and all components necessary in

completing a combustion air vent system.

After completing the installation of the optional

combustion air vent system the actuator arm

must be put in service and tested to ensure

proper operation before completing any enclo-

sure around the firebox. Failure to do so may

result in extensive and costly rework.

WARNING: DO NOT REMOVE THE AC-

TUATOR ARM LOCKING SCREW UNLESS

THE COMPLETE OUTSIDE AIR VENT SYS-

TEM HAS BEEN INSTALLED IN ACCOR-

DANCE WITH THE DETAILED INSTRUC-

TIONS PROVIDED WITH THE KIT.

Figure 45

Locate the actuator arm along the right side of

the appliance firebox opening and refer to

Figure 45

. After completing the installation of

the Outside Combustion Air Kit remove and

discard the actuator arm locking screw.

To operate, push the end of the actuator to the

left as shown in

Figure 45

, until it "pops" free of

its "locked" position. Pull the actuator forward

to open the combustion air door, and push it

back to close. To "lock" the combustion air

door closed, ensure the actuator is pushed all

the way back then push the end of the actua-

tors to the right until the step in the actuator

moves behind the appliance front face within

the slotted opening.

Operate the actuator through several cycles

including the "lock position. Ensuring proper

operation and freedom of movement. Return

the actuator arm to the locked position.

Gas Line Connection

Install a ¹⁄₂" gas supply line through fireplace

wall for connection to a decorative gas appli-

ance inside the firebox. Outside, the gas supply

line connects to a gas shut-off valve recessed

flush into the wall or floor. The valve should be

controlled by a removable valve key for safety.

Always plumb gas line installation per local

codes. Check all connections with soap suds;

leaks will bubble. Never test any gas line con-

nection with a match or open flame.

This provision is intended for connection to a

decorative gas appliance incorporating an au-

tomatic shut-off device and complying with the

Standard for Decorative Gas Appliances for

installation in vented fireplaces, ANSI Z21.60

(1991) or American Gas Association draft re-

quirements for Gas-Fired Log Lighters for Wood

Burning Fireplaces, Draft No. 4 dated August,

1993. Install in accordance with the National

Fuel Gas Code, ANSI Z223.1. This complies

with the revised U.L. 127 standard.

Remove Locking Screw

and “Pop” Actuator to the

Left Before Initial Use

Combustion Air

Actuator

Pull Forward to Open,

Push Back to Close

Vent Free Appliances

This unit has been tested and approved to

ANSI/IAS/AGA Z21.11.2 for use with unvented

gas appliances and complies with the stan-

dard for Factory-Built fireplaces, UL 127, when

installed with unvented gas log sets. Special

instructions with regards to mantle installa-

tions must be taken into consideration when

installing such appliances.

The unit has been tested for use with any

unvented log sets having a maximum rating of

32,000 BTU. The minimum mantle configura-

tion for these log sets are outlined in

Figures

46 and 47

Log sets with 40,000 BTU may be installed

provided that no combustible mantle projec-

tions are placed lower than 18 inches from the

fireplace opening.

These fireplaces have been marked with a

maximum rating of 32,000 BTU to assure that

homeowners do not exceed the allowable lim-

its for all allowed installations of mantles. That

limit may be increased to 40,000 BTU, pro-

vided that the mantle installed complies with

the 18-inch limitation and a copy of these

instructions are available.

NEVER INSTALL AN UNVENTED GAS LOG

SET WITH A BTU GREATER THAN 32,000 IF

COMBUSTIBLE MANTLE PROJECTIONS ARE

LOWER THAN 18 INCHES ABOVE THE FIRE-

PLACE OPENING.

BLOWER THREE

PRONGED PLUG TO

GROUNDED OUTLET

WARNING: MODELS THAT HAVE THE

"-2" SUFFIX HAVE NOT BEEN TESTED

WITH AN UNVENTED GAS LOG SET. TO

REDUCE RISK OF FIRE OR INJURY, DO

NOT INSTALL AN UNVENTED GAS LOG

SET INTO THIS FIREPLACE.

CAUTION: WHEN USING THE DECORATIVE

GAS APPLIANCE, THE FIREPLACE DAMPER

MUST BE SET IN THE FULLY OPEN POSITION.

CAUTION: PLUMBING CONNECTIONS SHOULD

ONLY BE PERFORMED BY A QUALIFIED, LI-

CENSED PLUMBER. MAIN GAS SUPPLY MUST

BE OFF WHEN PLUMBING GAS LINE TO FIRE-

PLACE OR PERFORMING SERVICE.

If you’re installing a gas line, connect it before

the fireplace is framed and enclosed in the

finished wall. The gas knockout is determined

by the indentation located at the bottom and

slightly off center in the side refractories.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

It is especially important to insulate between

the studs of an outside chase cavity and under

the floor if the floor is above ground level. Do

not place insulation directly against the fire-

place or chimney system.

FIREPLACE FINISHES

Mantels and Trim

It is sometimes best to frame your fireplace

after it is positioned and the chimney is in-

stalled. Frame enclosure for chimney and fire-

place with 2 x 4’s (or heavier) lumber.

Note: The header may rest on the two (2) metal

top spacers on top of the unit but the header

must not be notched to fit around the spacers.

These fireplaces may sit directly on a combus-

tible surface. A 2" air space is required be-

tween combustible framing and the chimney.

A 1" air space is required between combustible

framing and fireplace outer wrapper. In Canada,

the minimum height for a combustible mantel

is 18" (457 mm) above the fireplace opening.

Figure 46

shows typical Canadian installa-

tions. For installations other than Canada,

combustible mantels and trim may be in-

stalled 12" above the fireplace opening as per

NFPA 211, Section 7-2.3.3. and

Figure 47

. If

a mantel is of a noncombustible material, it is

exempt from these requirements as long as it

does not interfere with the installation or op-

eration of glass doors.

*Note: 2" clearance to combustibles required

in Canada.

Hearth Extensions and Wall Shields

A hearth extension must be installed with

all fireplaces. It is to protect the combustible

floor in front of the fireplace from both radiant

heat and sparks. The hearth extension must

extend 8" beyond both sides of the fireplace

opening and 16" beyond the front (

Figure 48

Use a hearth extension constructed of a du-

rable noncombustible material having an equal

or greater insulating value of k = .43BTU IN/FT2

HR °F or a thermal resistance that equals or

exceeds r = 2.33 HR °F FT2/BTU IN. With these

values, determine the minimum thickness/

material required using the formula and the

Table on page 17.

Note: Any noncombustible material whose k

value is less than .43 or whose r value is more

than 2.33 is acceptable.

If the fireplace is installed on a combustible

floor, use the metal safety strips (provided) on

the floor extending half under the fireplace and

half under the hearth extension (refer to

Fig-

ures 6 and 7

A wall shield is required where a continuous

perpendicular side wall is within 12" of the

fireplace opening, (

Figure 49

). Use a 36" x 36"

wall shield constructed of millboard or a du-

rable, noncombustible material having an equal

or greater insulating value than K = .54BTU IN/

FT2 HR °F. At no time may a perpendicular side

wall be positioned closer than 9 inches.

Figure 47

THE KNOCKOUT IS ALWAYS REMOVED FROM

INSIDE THE FIREPLACE. DO NOT REMOVE

THE KNOCKOUT UNLESS YOU ARE INSTALL-

ING A GAS LINE. If removal is attempted from

the outer wrapper, side refractory damage may

occur. With a medium-sized hammer, lightly

tap the surface of the indentation. The refrac-

tory material is very thin in this area and is easily

removed. Once a small hole has been made,

continue tapping until you have reached suffi-

cient diameter for the gas line to fit through. The

entire knockout does not have to be removed.

Remove insulation in the gas line channel.

IMPORTANT: REPACK INSULATION MATERIAL

IN SQUARE HOLE AROUND GAS LINE, INTE-

RIOR AND EXTERIOR OF FIREPLACE, TO SEAL.

Glass Doors

If glass doors are to be installed on these

fireplaces, refer to specific installation instruc-

tions packed with the glass doors. Use only the

doors that are listed for use with these fire-

places. Use of other non-listed glass door on

these fireplaces may constitute a potential fire

hazard and is not recommended.

CAUTION: CERTAIN GLASS DOORS OVERLAP

THE BLACK METAL FACING OF THE FIRE-

PLACE. IF THE FIREPLACE HAS BEEN FACED

WITH NONCOMBUSTIBLE MATERIALS, THERE

MIGHT NOT BE SUFFICIENT CLEARANCE TO

INSTALL THE GLASS DOORS OF YOUR

CHOICE. ENSURE ADEQUATE CLEARANCE IS

MAINTAINED AT ALL TIMES SO AS NOT TO

INTERFERE WITH THE INSTALLATION AND

OPERATION OF GLASS DOORS.

COLD CLIMATE INSULATION

If you live in a cold climate, it is especially

important to seal all cracks around the fireplace

opening with noncombustible material and

wherever cold air could enter the room. Sur-

rounding materials must be caulked where it

meets the black metal facing of the fireplace to

avoid cold air intrusion. Use noncombustible

caulking material only on fireplace facing to

seal. Also, the outside air inlet duct should be

wrapped with noncombustible insulation to

minimize the formation of condensation. Do

not place insulation materials on top of fire-

place or against chimney sections.

Note: A 1"* air space must be preserved for all

combustible materials extending for any con-

tinuous length adjacent to the chimney. Figure 46

12"*

Min.

8 3/8"*

Fireplace

Opening

Spacer

Combustible

Mantel

and Trim

12"

Max.

1 1/2"

Finished

Wall

Typical Installation

*Both Of These Dimensions Must Be At Least 18”

When An Unvented Gas Log Set Rated At 32,000

BTU Or Higher Is Used. (Maximum 40,000 BTU)

Header

Fireplace

Opening

Spacer

Finished

Wall

Canadian Installation

Header

8" Max.

(203mm)

18" Min.

(457mm)

Combustible

Mantel

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17

Figure 48

Figure 49

Methods of Determining Hearth Extension

and Wall Shield Equivalents

To determine the thickness required for any

material when either the k or r values are

known:

TM= Thickness of material in inches

kM= K value of desired material

rM= R value of desired material

TL= Minimum listed thickness

Example: Micore CV230 is to be used for the

hearth extension fireplace. How thick must this

material be?

Using the k formula:

Desired k value of desired Min. thickness

Required = material (per inch) x of Listed

Thickness k value of listed Material

material (per inch)

TM (inches) = kMx TL

.43

TM (inches) = 0.43* x 1"

0.43

Answer using k = 1 x 1" = 1

1" thickness Micore will be required.

Using the r formula:

Desired r value of listed Min. thickness

Required = material (per inch)x of Listed

Thickness r value of desired Material

material (per inch)

TM (inches) = 2.33 x TL

TM (inches) = 2.33 x 1"

2.33*

Answer using r = 1 x 1" = 1 =

1" thickness Micore will be required.

At times it is important to know what combina-

tion of materials are acceptable for use as

hearth extensions. The “R values” are used to

determine acceptable combinations of materi-

als because “R values” are additive where r and

k values are not.

Hearth Extension Dimensions

A16"

B35"

C8"

D51"

“R value” = 1 = r x thickness of material used

Alternative Hearth Extension

and Wall Shield Materials

Listed Values Min. Thick

Material k r TL

Millboard .43 2.33 1"

Alternative Values Min. Thick

Materials k r TM

Wonderboard 1.92 0.56 4 ¹⁄₄"

Common brick 5.00 0.20 11 ⁵⁄₈"

Cement mortar 5.00 0.20 11 ⁵⁄₈"

Ceramic tile 12.5 0.08 29 ¹⁄₈"

Marble 11.0 0.09 25 ⁷⁄₈"

Micore CV230 0.43 2.33 1"

(U.S. Gypsum)

Ceraform 126 0.27 3.70 ⁵⁄₈"

(Johns-Manville)

Example: Given that the required “R value” for

a suitable hearth extension used must be equal

to or greater than:

“R” = r x TL = 2.33 x 1" = 2.33.

If it is desired to elevate a marble hearth exten-

sion to a level of 5" or more above the floor

surface. What combination of noncombustible

materials can be used to accomplish this?

If common brick is used so that the 3 ¹⁄₂"

dimension is the height, “R” for the common

brick becomes:

“R”M = r x TM = 0.20 x 3 ¹⁄₂" = .70

Using ¹⁄₂" of mortar to set the brick, “R” for the

mortar is calculated as follows:

“R”M = r x TM = 0.20 x ¹⁄₂" = .10

*value taken from chart

If fireplace is installed diagonally across a 90°

corner; no wall shields are required.

Wall Shield Required

Where Less Than 12"

36"

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Secure the hearth extension to the floor to

prevent possible shifting.

FINISH TO YOUR TASTE

There are a wide variety of “finished looks” for

these fireplaces, from formal wall decor with

elaborate mantels to rustic wood paneling or

warm brick facings.

Only noncombustible materials like stone, tile,

brick, etc., may overlap the black front facing.

Do not extend these materials beyond the black

facing and into the firebox area. Be sure not to

interfere with the installation and operation of

glass doors or block the upper or lower grilles.

Seal all joints between the black facing and wall

surrounds to prevent air intrusion. Use non-

combustible caulking material only to seal the

black metal facing to the surround material on

the finished wall.

Combustible materials may project beyond the

sides of the fireplace opening as long as they

are kept within the shaded areas illustrated in

Figure 52

Figure 51

Figure 52

12"

12" Min. Distance To

Unprotected Side Wall

45°

Combustible

Materials

Allowed In

Shaded Area

“Safe Zone”

9" 1"

Min. Distance To

Protected Side Wall

Fireplace

A ³⁄₄" marble slab set in ¹⁄₂" mortar covers the

brick, “R” for the marble and mortar becomes:

“R”M = r x TM = 0.09 x ³⁄₄" = .068

“R”M = r x TM = 0.20 x ¹⁄₂" = .10

The sum of all “R values” is:

.70 + .10 +. 068 + .10 = .968

This would not be an acceptable combination

of material for the hearth extension since the

total calculated “R value” of the materials used

is under the required “R value” of 2.33. An

additional layer of insulating materials must

be used.

WARNING: THE CRACK BETWEEN THE

FIREPLACE AND THE HEARTH EXTEN-

SION MUST BE SEALED WITH A NON-

COMBUSTIBLE MATERIAL.

WARNING: WHEN INSTALLING HEARTH

EXTENSION IN FRONT OF A NON-CIRCU-

LATING FIREPLACE MODEL, THE FIRE-

PLACE MUST BE RAISED IF HEIGHT OF

HEARTH EXTENSION EXCEEDS 7" ABOVE

THE BOTTOM OF FIREPLACE (

FIGURE 50

Max. Thickness Of Hearth Extension When

Non-Circulating Models Are On The Floor

WARNING: WHEN INSTALLING THE

HEARTH EXTENSION BE CAREFUL NOT

TO BLOCK THE HEAT-CIRCULATING AIR

INLET GRILL ON CIRCULATING MODELS.

WARNING: WHEN INSTALLING HEARTH

EXTENSION IN FRONT OF A CIRCULAT-

ING FIREPLACE MODEL, THE FIREPLACE

MUST BE RAISED IF HEIGHT OF HEARTH

EXTENSION EXCEEDS 2" ABOVE BOTTOM

OF FIREPLACE (

FIGURE 51

Figure 50

5 1/2"

Max. Thickness Of Hearth Extension When

Circulating Models Are On The Floor

Shipping Weight 188 lbs.

INSTALLATION COMPONENTS

The following items are available for use in the

installation of this appliance.

Unit Mounted

Blower Switch Kit 91L48 FUBSK

Chimney Section 63L10 FTF8-12

63L13 FTF8-18

63L14 FTF8-36

63L15 FTF8-48

Canadian 62L92 FTF8-18C

Chimney Section 62L93 FTF8-36C

Take Off Boot 91L04 FATO

Storm Collar 63L59 FSC

Locking Band 63L60 FLB

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19

INSTALLATION COMPONENTS

Outside Combustion Air Kits

(with duct) 81L87 FOAK

(without duct) 81L88 FOAK-LD

Combination

Offset/Return Elbow 63L28 FTF8-OR15

Firestop Spacer (Flat) 63L29 F8FS

Firestop Spacer (Flat) 63L31 F8FS-2

63L38 F8F6

Flashing 63L39 F8F12

Round Termination 63L42 FTF8-CTD

Chase Termination

(Square) 63L48 FTF8-CT1

Chase Termination

(Round) 63L45 FTF8-CTDT

Chase Termination

(Square) 63L51 FTF8-CT2

Forced Air Blower Kits

-Single Speed 80L84 FBK-100

-Variable Speed 80L85 FBK-200

(FBK-200 Models Only)

Chase Termination 96L20 FTF8-CTT

Chase Termination 96L22 FTF8-ATT

Stabilizer 63L25 FTF8-S4

Firestop Spacer (30°) 63L30 F8FS30

Firestop Spacer (30°) 63L32 F8FS30-2

Offset/ Return

Package (30°) 63L22 FTF8-ES30

Attic Shield Assembly 63L67 FTF8-FSASCold Climate Kit 63L65 FTF8-CCK3-LD

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

P/N 700,026M REV. C 11/2003

The manufacturer reserves the right to make changes at any time, without notice, in design,

materials, specifications, prices and also to discontinue colors, styles and products.

Consult your local distributor for fireplace code information.

1110 West Taft Avenue

Orange, CA 92865

Superior Br 42 Users Manual B42 (700,026M) NC 01/01

Navigation menu

Versions of this User Manual:

Views

Navigation