Suprema XPSM RFID Reader User Manual

Suprema Inc. RFID Reader Users Manual

Users Manual

-1-The list below is to keep user’s safety and prevent any loss. Please read safety precautions carefully before use.Do not install the device in a place subject to direct sun light, humidity, dust or soot.Do not place a magnet near the product. Do not place the device next to heating equipments.Be careful not to let liquid like water, drinks or chemicals leak inside the device.Clean the device often to remove dust on it.In cleaning, do not splash water on the device but wipe it out with smooth cloth or towel. Safety precautionsIt may cause a damage or a failure to the product.It may cause a failure.
-2-Do not drop the device. Do not damage the device.Do not disassemble, repair or alter the device.Do not let children touch the devicewithout supervision. Do not use the device for any other purpose than specified.Contact your nearest dealer in case of a trouble or problem. The warranty does net apply to any product damage cause by an arbitrary installation or repair.Safety precautionsThe list above is to keep user’s safety and prevent any loss. Please read safety precautions carefully before use.
-3-ProductcomponentsXPS bracketWall mounting screws(2 ea) Knife Blocks(2 ea) Shrinkable Tubes Software CDBasic componentsThe components shown above may differ depending on the installation environment.
-4-Cables and Connectors No Pin Name Full Name Color1485 GND 485 GND White (black string)2WGD GND Wiegand-GND Black3485 - 485 - Yellow (black string)4WGD D1 Wiegand-1 White5485 + 485 + Blue (white string)6WGD D0 Wiegand-0 Green7 IN 1 Input-1 Brown8RLY NO Relay Open Gray (white string)9 IN GND Input-GND Gray10 RLY COM Relay Com Green (white string)11 IN 0 Input-0 Purple12 RLY NC Relay Close Orange (black string)13 TX+ TX+ (LAN) Pink14 PWR IN+ Power IN+ Red15 TX- TX-(LAN) Orange16 PWR IN- Power IN- Black (white string)17 RX+ RX+ (LAN) Blue18PWR OUT+ Power OUT+ Light Blue19 RX- RX-(LAN) Yellow20 PWR OUT- Power OUT- Black (white string)21 VB1 VB1 Green (black string)22 VB2 VB2 Brown (white string)23 VB1 VB1 Green (black string)24 VB2 VB2 Brown (white string)
-5-Cable Pin Name Color1RelayRLY NC Orange (black string)2 RLY COM Green (white string)3 RLY NO Gray (white string)4WiegandWGD D0 Green5WGD D1 White6WGD GND Black7SwitchIN 0 Purple8IN 1 Brown9IN GND Gray10485485+ Blue (white string)11 485- Yellow (black string)12 485 GND White (black string)Cables and ConnectorsAdaptor Connector Pin Name ColorPowerPOWER OUT - Black (white string)POWER OUT + Light Blue3POWER IN - Black (white string)1POWER IN + RedCable Specification
-6-Power Connection112V ±10%, at least 1500mA.Comply with standard IEC/EN 60950-1.To share the power with other devices, use a power supply with higher current ratings.Recommended power supplyPin Pin Name Color14 PWR IN+ Red16 PWR IN- Black (white string)
-7-RS485 Connection for Host CommunicationPin Pin Name Color1485 GND White (black string)3 485 - Yellow (black string)5 485 + Blue (white string)
-8-Relay Connection –Fail safe lockPin Pin Name Color10 RLY COM Green (white string)12 RLY NC Orange (black string)
-9-Relay Connection –Fail secure lockPin Pin Name Color8RLY NO Gray (white string)10 RLY COM Green (white string)
-10-Relay Connection -Automatic doorPin Pin Name Color8RLY NO Gray (white string)10 RLY COM Green (white string)
-11-Digital Input Connection (Alarm, Emergency S/W)Pin Pin Name Color7IN 1 Brown9IN GND Gray11 IN 0 Purple
-12-Digital Input Connection (RTE, Door sensor)Pin Pin Name Color7IN 1 Brown9IN GND Gray11 IN 0 Purple
-13-Wiegand InputWiegand Input/OutputWiegand OutputPin Pin Name Color2WGD GND Black4WGD D1 White6WGD D0 GreenPin Pin Name Color2WGD GND Black4WGD D1 White6WGD D0 Green
-14-OutputPin Pin Name Color10 RLY COM Green (white string)12 RLY NC Orange (black string)18 PWR OUT + Light Blue20 PWR OUT - Black (white string)Caution : Max. 700mA is supplied using adapter for the external output. Be careful to satisfy the power capacity in use.
-15-Installation Reference 1 -Stand alone
-16-SpecificationCPU 32 bit Micro-processorMemory 8MB FLASH + 16MB SDRAM RF Card 13.56 MHz Mifare(XPSM)User Capacity 40000 userLog Capacity 50000 logNetwork interfaces TCP/IP, RS485 IP Rate IP 65 classSound Multi-tone buzzerLED Multi-color LED I/ORelay x 1Tamper x 1Switch input x 2 Wiegand x 1Power 12VdcOperating Temperature -20 ~ 50°C Size 80 x 120 x 11mm (W x H x D ) Certificates CE, FCC, KCC, IP65It may be occurred the risk of explosionfor improper replacement of battery. Please use the specified battery according to proper instruction.Caution for RTC Battery
-17-Min. Typ. Max. NotesPowerVoltage (V) 10.8 12 13.2 Use regulated DC power adaptor onlyCurrent (mA) - 200 1500Switch InputVIH (V) - TBD -VIL (V) - TBDPull-up resistance (Ω) - 4.7k - The input ports are pulled up with 4.7k resistorsTTL/WiegandOutputVOH (V) - 5 -VOL (V) - 0.8 -Pull-up resistance (Ω) - 4.7k - The outputs ports are open drain type, pulled up with 4.7k resistors internallyRelaySwitching capacity (A) - - 10.3 30V DC125V ACSwitching power (resistive) - - 30W37.5VADCACSwitching voltage (V) - - 110125 DCACElectrical Specification
-18-Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interface, and (2) this device must accept any interface received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limit of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, user and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more the following measures:1. Reorient / Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected.4. Consult the dealer or an experienced radio/TV technician for helpCautionWarningInformation to UserFCC Rules

Navigation menu