Surplus Pro BTR103 Bluetooth Receiver User Manual
Surplus Pro Co. Ltd. Bluetooth Receiver
Users Manual
User Instruction Manual
For
BTR103BMW/ BTR103BVWA/ BTR103MB
Disclaimer
Preface
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any of the material contained herein, may be
reproduced without the express written consent of the manufacturer, Nov
2012.
Trademarks
Other product names mentioned herein are used for identification purpose
only and may be trademarks and/or registered trademarks of their
respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this
manual, the manufacturer and distributor assume no liability resulting from
errors or omissions in this manual, or from the use of the information
contained herein.
Safety Notice!!! Must Read Before Use!
Road Safety
We strongly advise that full attention is to be paid to the traffic conditions
whenever the vehicle is moving. Distraction of attention can lead to
dangerous traffic situation. Even when using a handsfree car kit driver is
always advised to avoid phone call during a difficult and complex traffic
situation
Use Only Approved Replacement Parts
Please always use official parts for your unit as unknown spare or replacement
parts may lead to malfunction.
User Manual
Designed for in-Car integration with 30 pin iPod connector
1. Core Component
1) Connection LED Indicator
2) 30 Pin Jack
2. Installation
Locate the 30 pin cable that comes with your original in-Car iPod integration.
Plug the 30 pin cable into the jack at the bottom of the unit until it is locked
in.
3. Pairing for the first time
Switch the Bluetooth on from the General setting menu on your iPhone/iPod
Touch/iPad and search for the device nearby. Select “CarPro” to connect and
enter “0000” when prompted a message indicating you need to enter pass
code. Once connected the Blue flashing LED will become solid.
4. Pairing with another iPhone, iPod or iPad
To pair with another iPhone, iPod or iPad device you will need to switch off
the Bluetooth function on the current device that is in connection with
CarPro. As soon as the connection is stopped the Blue LED on the unit should
start flashing to indicate Pairing mode is ready. Follow the steps in “Section
3. Pairing” to pair another device to CarPro.
5. Connect with previously paired phone
If you wish to change to another device which has already been paired with
CarPro before, you will need to switch off the Bluetooth function on the
current device that is in connection with CarPro. Then, go to the paired
Bluetooth device list on your phone, iPad or iPod touch and select CarPro to
reconnect.
6. Controlling your music
Access the iPod music menu on your head unit. For instance, press the
Media key on Audi Symphony III or Concert III head unit to access the iPod
menu and use the Knob or arrow keypad to browse the iPod library. Use the
buttons indicated on the car screen to play, stop, next or previous song.
Different vehicles may have different ways of accessing and controlling the
iPod music.
Please refer to your car manual or contact the car manufacturer for further
information on how to operate iPod in your car.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.