Suzhou Sate Auto Electronic TSB41 Tire Pressure Monitoring System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2677245
Application ID	tJDdMIDWod1gIybqUNi1TA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.45kB (368146 bits)
Date Submitted	2015-07-13 00:00:00
Date Available	2015-07-13 00:00:00
Creation Date	2015-07-12 05:33:11
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2015-07-12 13:33:19
Document Title	Users Manual
Document Creator	Microsoft® Office Word 2007
Document Author:	jzs

TSB41/42/43/44 Sensor User Manual V1.0
TSB41/42/43 Sensor User Manual
1 General Description
1.1 Purpose
This manual is to make sure the reliability of communication between receiver
and sensor, and tightness between sensor and wheel hub.
2 Basic Requirements
2.1 Tire valve
2.1.1 Suitable pore size for tire valve
The valve is suitable for wheel hub with tire valve pore size of Φ 11.5±
0.2mm.
2.1.2 Valve nut dimension
Valve nut O.D. is Φ 14mm, length is 19mm。
2.2 Housing
Housing of the sensor must be sealed to meet water proof and dust proof
requirement, with protection degree IP54. The housing material should make the parts
meet vibration, shock and drop requirement, and tests for vibration, shock and drop
should comply with test requirements of IS016750-3 2007 《 Road Vehicles ─
Environmental conditions and testing for electrical and electronic equipment》.
Housing material: PA6+GF30
2.3 Dimension requirement
TSB4X dimension is as below:
1 of 4
TSB41/42/43/44 Sensor User Manual V1.0
Item
Size
Length
76mm
Width
63mm
Height
26mm
Remark
Including tire valve
2.4 Installation requirement
4N.m(±0.5 N）torque force should be employed to screw tire valve nut when install
TSB4x sensor to make sure the installation reliability. After installation, there
should be 0-3mm space between sensor camber side and wheel hub camber side, as below:
Installation environment requirement:
Sensor dropped from height above 1m can’t be applied on vehicle any more;
There shouldn’t be static electricity above 6KV in sensor installation site;
Installation steps:
① Screw the sensor valve nut off, and get the valve through wheel hub valve pore.
2 of 4
TSB41/42/43/44 Sensor User Manual V1.0
② Screw the sensor nut by hand, and employ 12mm sleeve to tighten it（torque force
4N.M）.
③ Mount the rubber tubes;
④ Inflate the tires to standard pressure, and check whether there is leakage
between the valve and lock nut with soap water;
⑤ Screw the valve cap on to finish sensor installation;
⑥ Check the tire’s dynamic balance after sensor installation, and then install
the other three sensors one by one, and mount the tire.
Note: After sensor installation, the tires need to be re-balanced.
3 of 4
TSB41/42/43/44 Sensor User Manual V1.0
Note: During installation, the sensor need to be clean, not polluted by lubricant
oil, etc;
During tire mounting and dismounting, the sensor shouldn't be touched;
During tire inflation and deflation, no force should be employed to the sensor;
2.5 Temperature requirement
Operation temperature and storage temperature range of TSB4x sensor are as
below:
Parameter
Temperature range
Unit
Minimum
Maximum
Operation temperature
-40
125
℃
Storage temperature
-40
85
℃
2.6 Sealing requirement
Sealing test of TSB4x sensor after installation complies with standards of
GBT12836.2（Tubeless valves--Part 2: Clamp-in valves）-7.2.2.
Prepared by:
Reviewed by:
4 of 4
Approved by:
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any other
antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : jzs
Title                           : TRP12接收器安装要求
Create Date                     : 2015:07:12 05:33:11Z
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2015:07:12 13:33:19+08:00
Metadata Date                   : 2015:07:12 13:33:19+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:a922ca3a-452e-4ef4-b6c0-a968670ffcf6
Instance ID                     : uuid:04cfe8d8-5fae-49f5-bccb-af1f63785078
Page Count                      : 5
Author                          : jzs

EXIF Metadata provided by EXIF.tools