| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3209392 |
| Application ID | TMPS7aB1Tzc8ehmrOs1ikg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 161.5kB (2018810 bits) |
| Date Submitted | 2016-11-28 00:00:00 |
| Date Available | 2016-11-28 00:00:00 |
| Creation Date | 2016-11-25 00:15:44 |
| Producing Software | Microsoft: Print To PDF |
| Document Lastmod | 2016-11-25 00:17:35 |
| Document Title | User Manual |
| Document Author: | MRT |
5d
1111 SD10 Wi-Fi Module with S9082
S-82-GESNC
IEEE 802.11b/g/n 1T1R SDIO Wi—Fi Module
Features :
.9 Supporting Standard - I: a T E" n— q-
. , . t” ‘
IEEEStd. 802.111: ‘ v v: .Ll- “
IEEE Std. 802.11g
IEEE Std. 802,11n
‘ Chip Solution
590825
no
Interface
SD10
2‘ Band
2.46
01' Size
12.5 mmx12.5 mm
Stamp
S-SZ-GESNC SMD 802.11b/g/n lSOMbps 2.4 GHz
hole
SmartChip Microelectronics Technology(Suzhou) Co., LTD
Addr:9A,Scieuee Park, 1355 Jinjihu Avenue, Suzhou Industrial Park, 215021
Fax : +86-0512—62620002
Web: http://wwwscieincLomxn
Tel: 1 8 67051276262003 9
6C, SVSZVGESNC
lln SDIO Wi-Fi Module with 59082
User Manual
1. Introduction
S-SZ-GESNC is a Wi-Fi wireless module based on the SCI S9082C chip. The module operates in the
2.4126Hz ~ 2.484GHZ frequency band and supports 802.11b / g / n protocol. This document describes the
features and usage of the module.
1.1 Module architecture
S-BZ-GESNC is a Wireless LAN (WLAN) module based on SCI SQOSZC wireless chip development.
S9082C is a highly integrated wireless LAN SOC chip that supports SDIOH /SDIOZ.0, supports 802.11b / g/
n protocol standard. The S9082C integrates a MAC, a lTlR baseband and RF link, which provides a complete,
high-speed wireless LAN single-chip solution. S9082C hardware block diagram shown in Figure l:
___1 ‘___
l 3.3V m
l l Inlerfate l
40M] 12
('1 ystal
[ntertaie MAC
('I’mfigllmrmn
CUHIIUI Interface
WLAN
2 «ij
Brisebsnd
( PH Y )
TI unseen er
Figure l. S9082C block diagram
1. 2 Supporting Standard
The SeRZeGESNC module supports the following protocols:
IEEE Std. 802.11b
IEEE Std. 802.11g
5C, $7827GESNC
lln SD10 Wi-Fi Module with S9082
IEEE Std. 802.11n
1.3 Basic characteristics
The basic indicators am as follows:
2.412~2.484GHZ
802.11b/yn(1x1)
11b: DBPSK, DQPSK and CCK and D555
Hg: BPSK, QPSK, 16QAM, 64QAM and OFDM
lln: MCSO~7 OFDM
llb:l, 2, 5.5 and lleps
11g:6, 9,12,18,24, 36, 48 and 54 Mbps
lln: MCSO~7, up to ISOMbps
44pin
SD10 2.0
4-layers design
Typical. 12.5mm*12.5mm
-20'C to +70'C
740‘Cto +85'C
3,3V +/-10% (Ripple: SSOmVp-p)
394mA @15dBm@54Mbps TX mode
5C, $7827GESNC
lln SDIO Wi-Fi Module with S9082
A U U U U U U U U U U U
0 0 U D 0 O U 0 D 0 0
Z Z Z Z Z Z Z Z Z Z Z
3" m a Q d as :0' I; Q m g
m .
N (0 v m m vs no a) o — N
‘— ._ ‘— _ .— ‘_ .— ._ N N N
V n n n n n n n n A n n
12.5
< .
Figure fo‘fl‘ifl’fi (Top View)
NOTEl : General tolerance i0.15mm unless otherwise stated
NOTEZ: Unit mm
1 GND GND
2 Wi-Fi ANT RF RX&TX Signal
3 GND GND
4 NC NC
5c:
$782iGF/SNC
lln SD10 Wi—Fi Module with 59082
5 NC NC
6 NC NC
7 NC NC
8 NC NC
9 VDD33 Power supply For system (3.3Vi03V)
10 NC NC
11 NC NC
12 CS Chip select. Actlvity hlgh: Intemal pull high to 3.3V at
l(l(lKfl
l3 WLiHOSTiwAKE For WLAN wake-up HOST, Internal pull high to 3.3V at
100K!)
14 SD_D2 SD10 Data Line 2
15 SD7D3 SD10 Data Linc 3
16 SDiCMD SDIO Command Input
17 SDiCLK SD10 Clock Input
18 SDiDO SD10 Data Line 0
19 SDiDl SD10 Data Linc 1
20 GND GND
21 NC NC
22 VDDIO VDD for SD10 Pin, the power supply is same as the signal
level of
SD10 bus (3.3V ~ 1.8V)
23 NC NC
24 NC NC
25 NC NC
26 NC NC
27 NC NC
28 NC NC
29 NC NC
5c:
$782iGF/SNC
lln SD10 Wi—Fi Module with 59082
30 NC NC
31 GND GND
32 NC NC
33 GND GND
34 NC NC
35 NC NC
36 GND GND
37 NC NC
38 NC NC
39 NC NC
40 NC NC
41 GND GND
42 NC NC
43 NC NC
44 NC NC
5c!
S-SZ-GESNC
11n SDIO Wi-Fi Modulc with 59082
3. RF specifications
All parameters are based on the test results of the module DUT, and the test ambient temperature is + 25 ° C.
3.1 802.11b Mode
Specification IEEEROZJ lb
Mode DSSS / CCK
Channel CH1 -CHll
Data rate 1,2, 5.5, lleps
TX Charactcristics Min. Typ. Max Unit
1. Power Levels((1a]ibrated)
1)Target 9.5 16.5 17.00 dBm
2. Spectrum Mask @ target power
1) to +/-11MHzto +/-22MHz Pass
2) fc > +/—22Mllz Pass
3. Frequency Error 4.8 KHz
RX Characteristics Min. Typ. Max. Unit
4 Minimum Input Level Sensitivity
1) leps (FER §8%) -‘)6 -94 (131:)
2) ZMbps (FER E 8%) -94 -92 (13:11
3) 5.5Mbps (FER E 8%) 790 786 dBm
4) lleps (FER 28%) -88 -84 (Him
5 Maximum Input Level (FER §8%) -8 -5 dBm
3.2 802.11g Mode
Specification IEEESOZJ lg
Made OFDM
ChannCI CH1 -CH11
5c!
$782iGF/SNC
11n SD10 Wi-Fi Module with 59082
Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps
TX Characteristics Min. Typ. Max. Unit
1, Power Levels
1) Target 4,0 11,5 12.0 dBm
2. Spectrum Mask @ target power
1) at fc +/—11MHZ Pass
2) at fc +/—20MHZ Pass
3) at fc > +/730M117 Pass
3 Constellation Error(EVM)@ targct powcr
1) fiMbps -31,3 dB
2) 9Mbps -30.8 dB
3) 12Mbps -30.9 dB
4) 18Mbps 730.5 dB
5) 24Mbps -3 l .2 dB
6) 36Mbps -30.6 dB
7) 48Mbps -31.1 dB
8) 54Mbps -30.2 dB
4 Frcqucncy Error 4.8 KHz
RX Characteristics Min. Typ. Max. Unit
5 Minimum Input Level Sensitivity
1) 6Mbps (PER § 10%) -91 -87 dBm
2) 9Mbps (PER § 10%) -89 -85 dBm
3) 12Mbps (PER f10%) 786 782 dBm
4) 18Mbps (PER §10%) 784 780 dBm
5) 24Mbps (PER ‘5’ 10%) -81 -77 dBm
6) 36Mbps (PER 2 10%) -79 -75 dBm
7) 48Mbps (I’ER § 10%) -76 -72 dBm
8) 54Mbps (I’ER § 10%) -74 -70 dBm
6 Maximum Inpuchvcl (PER 210%) 78 75 dBm
5c!
S-SZ-GESNC
11n SDlO Wi-Fi Module with 59082
3.3 802.11n HT20 Mode
Specification lehXOZJln HTZO @ 2.4GHz
Mode OFDM
Channel CH1-CH11
Data rate (MCS index) MCSO/1/2/3/4/5/6/7
TX Characteristics Min. Typ. Max. Unit
1. Power Levels
1) Target 4.3 13.0 14.0 dBm
2. Spectrum Mask @ target power
1) at fc +/—11MH7 Pass
2) at fc +/720Mllz Pass
3) at fc > +/—30MH7 Pass
3. Constellation Error(EVM)@ target power
1) MCSO -32.3 dB
2) MCS] -32.4 dB
3) MCSZ 731.9 dB
4) MCS3 -32.5 dB
5) MCS4 -32.7 dB
6) MCSS -32.2 dB
7) MCSl) 731.9 dB
8) MCS7 731.7 dB
4. Frequency Error 4.8 KHZ
RX Characteristics Min. 'l'yp. Max. Unit
5. Minimum Input Level Sensitivity
1) MCSO (PER 2 10%) -90 -87 dBm
2) MCS] (PER 2' 10%) 786 783 dBm
3) MCSZ (PER 2' 10%) 784 78] dBm
4) MCS3 (PER 210%) -79 -76 dBm
5c!
S-SZ-GESNC
11n SDIO Wi—Fi Modulc with 59082
5) MCS4 (PER 210%) .77 —74 dBm
6)MCSS (PER 210%) .74 —71 dBm
7)MCS6(PER S10%) .73 —70 dBm
8)MCS7(PER S10%) .72 —69 dBm
6, Maximum Input Level (PER £10%) 78 .5 dBm
3.4 802.11n HT4O Mode
Specificatiun IEEE802.lln HT40 (a; 2.4GHz
MOdC OFDM
Channel CH3-CH9
Data rate (MCS index)
MCSO/123 456/7,8’9/1011’12131415
TX Characteristlcs Min. Typ. Max. Unit
1. Power Levels (Calibrated)
1) Target 4,] 10.0 10.] dBm
2. Spectmm Mask @ target power
1) at fc +/—22MHZ Pass
2) at fc +/—40MHZ Pass
3) at fc > +/—60MHZ Pass
3. Constellation ErroI(EVM)@target power
1) MCSO 732.5 dB
2) MCS] -32.7 dB
3) MCSZ -32.3 dB
4) MCS3 -32.5 dB
5) MCS4 -32.0 dB
6) MCSS -31.9 dB
7) MC36 732.2 dB
8) MCS7 -31.8 dB
4. Frequency Elmr 4.8 KHZ
10
5C, sisziaESNc
lln SD10 Wi-Fi Module with S9082
RX Characterisu'cs Min. Typ. Max. Unit
5. Minimum Input Level Sensitivity
1) MCSO (PER :10%) 788 784 dBm
2) MCSI (PER :10%) 784 780 dBm
3) MCSZ (PER 210%) -SI -77 mm
4) MCS3 (PER 210%) —77 —73 dBm
5) MCS4 (PER § 10%) -74 -70 dBm
5) MCSS (PER s 10%) ,70 766 dBm
7) MCSG (PER E 10%) -69 -65 dBm
8)MCS7 (PER E 10%) -68 -64 dBm
64 Maximum Input LevelO’ER E 10%) -8 -5 dBm
4. Power
IEEE802.11b
DSSS/CCK
2412~2484MHZ
1. 2. 5.5. lleps
IEEE802.11g
OFDM
2412~2484MHZ
6. 9. 12, 18, 24. 36. 48, 54Mbps
11
S7827GESNC
lln SD10 Wi-Fi Module with $9082
3 00
250
mA
1 06
60
IEEE802.1 In
OFDM
2412~2484MHZ
6‘5, 13, 195, 26, 39. 52, 58.5. 65Mbps
290
243
mA
I 10
62
Power down 3 6 uA
DTM1,LDO 1 1 .2
DTM3,LDO 4.4
mA
DTM 1 ,DCDC 6. 3
DTM3,DCDC 2.6
Connecwd state, no data is transmitted
102
LDO,DCDC
mA
Connected state, no data is
5 5
transmitted,DCDC
Connection status, transmit small
109
amounts of data,LDO
mA
Connection status, transmit small
62
amounts of data,DCDC
12
lln SDIO Wi-Fi Module with 59082
5. Antenna matching
PING RF antenna connection, please refer to the specific needs of the project design.
PINE
. ~> . 0
C3 _c2
Figure 3.Antenna matching
Module and the antenna are away from noise sources claim, and the antenna module to require as a
whole.
PING to WIFI module RF interface between the antenna and cabling requirements coplanar impedance of
500, recommend the use of arcs and lines, as short as possible.
C1, CZ, C3 composed of n—type matching network and close to the antenna interface design, the specific
adjustments based on the measured effects and recommended antenna layout deSign.
C1=10pF
Caution:
All platforms must follow this antenna deSign when using this module. If not follow completely, the FCC
authorization is no longer considered valid.
13
.\
i _
be .25. :5
22,; 2%: s;
0::
uszmsum
2352 Z<4>>
02mm0.~m.m
56’ SiflziGESNC
lln SD10 Wi-Fi Module with $9082
6. Welding conditions
300
'7 lrl W: 3
235—2500
250
240
217
200
150
100
50
so 100 150 200 250 300 S
Figure 6. Welding temperature curve
1,Temperature range: temperature: <150 'C, time: 60 ~ 90 seconds, slope control in the 1 ~ 3 'C / S between
2.Preheat temperature zone: temperature: 150 'C ~ 200 'C, time: 60-120 seconds, the slope between 03-03
3,Reflow soldering area: peak temperature 235 'C ~ 250 'C (recommended peak temperature
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.7
Linearized : No
Author : MRT
Create Date : 2016:11:25 00:15:44+08:00
Modify Date : 2016:11:25 00:17:35+08:00
Producer : Microsoft: Print To PDF
Title : D:\æł¼ç‚žæ¡‹ä»¶\桋件åŸæ¡£\熵è−¯å¾®çflµå’\1609RSU009-S-82-GESNC\1609RSU009-Reports\FCC\Comment\S-82-GESNC_User Manual 2016-11-23.pdf
Page Count : 20
EXIF Metadata provided by EXIF.tools