Suzhou SmartChip Semiconductor S83GESNB WLAN Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3209305
Application ID	NhvtJJov5tTybORIRzi6kw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	133.82kB (1672696 bits)
Date Submitted	2016-11-25 00:00:00
Date Available	2016-11-28 00:00:00
Creation Date	2016-11-25 00:14:35
Producing Software	Microsoft: Print To PDF
Document Lastmod	2016-11-25 00:14:35
Document Title	User Manual
Document Author:	MRT

lln USB Wi-Fi Module with S9083 '
S—83-GESNB
IEEE 802.11b/g/n 1T1 R Wi-Fi Module
Features :
0? Supporting Standard
IEEE Std. 802.11b
IEEE Std. 802.11g
IEEE Std. 802.11n
*3 Chip Solution
590830
~:~ Band
2.4G
4. Size
12.2mm x 13.0 mm
Stam p
S-83—GESNB SMD 802.11b/g/n 150Mbps 2.4 GHz
hole
SmartChip Microelectronics Technology(Suzhou) Co., LTD
Addr :9A,Science Park, 1355 Jinjihu Avenue, Suzhou Industrial Park, 215021
Fax : +86—0512-62620002
Web: http://www.soi-inc.com.cn
Tel: +86-0512—62620039
lln USB Wi-Fi Modulc with S9083
1. Introduction
S-83—GESNB is a WIFI wireless module based on SCI 890830 chip. The module operates in the
2.41ZGH2 -— 2.4846Hz frequency band and supports 802.11b lg / n protocol. This document describes
the features and usage of the module.
1.1 Module architecture
S-S3-GESNB is a wireless LAN (WLAN) module based on SCI 590820 wireless chip development.
890830 is a highly integrated wireless LAN SOC chip, supports USB2.0 interface, supports 802.11b / g
/ n protocol standard. 89083C integrates a MAC, a 1T1R baseband and RF link, which provides a
complete, high-speed wireless LAN single-chip solution. $90830 hardware block diagram shown in
Figure 1:
F 737 j F 7/5 j
L Input ‘ L Interface I
Inml‘ucu \t‘
umuun
L unnnl Interface
\VLAN
2 4 H7
Ti mum» e:
Mulching
Circuit Bdwluml
tl‘ll‘x')
Figure 1.39083C block diagram
1.2 Supporting Standard
The S-83-GESNB module supports the following protocols:
IEEE Std. 802.11b
IEEE Std. 802.11g
IEEE Std. 802.11n
5C, 57837GESNB
lln USB Wi-Fi Module with $9033
1.3 Basic characteristics
The basic indicators are as follows:
2.412~2.484GHZ
802.11b/gln(1x1)
11b: DBPSK, DQPSK and CCK and D888
11g: BPSK, QPSK, 16QAM, 64QAM and OFDM
11n: MCSO~7 OFDM
11b:1, 2, 5.5 and 11Mbps
119:6, 9, 12, 18, 24, 36, 48 and 54 Mbps
11n: MCSO~7, up to 150Mbps
Gpin
USB 2.0
4-Iayers design
Typical. 12.2mm‘13.0mm
-20°Cto +70“C
-40°Cto +85°C
3.3V +l—10% (Ripple: S30mVp-p)
370mA @15dBm@54Mbps TX mode
5c!
5783 iGESNB
lln USB Wi-Fi Module with $9083
2. Mechanical
13.0
1.VDD
2.UDM
3.UDP
4.GND
39083C
8.62
2.0
NOTE1: General tolerance $0.15mm unless otherwise stated
NOTEZ: Unit mm
12.2
Figure 2 Specifications (Top \fiew)
1 3.3V Power
2 USB DP
3 USB DM
4 GND
5 GND
6 ANT
sci
SESSEGFSNB
11n USB Wi-Fi Module with S9083
3. RF specifications
All parameters are based on the test results of the module DUT, and the test ambient temperature is
+25°C.
3.1 802.11 b Mode
Specification IEEE802.11b
Mode DSSS / CCK
Channel CH1-CH11
Data rate 1, 2, 5.5, 11Mbps
TX Characteristics Min. Typ. Max Unit
1. Power Levels(CaIibrated)
1) Target 9.2 19.0 19.5 dBm
2. Spectrum Mask @ target power
1) fc +/-11MH2 to +/-22MHZ Pass
2) fc > +/722MHz Pass
3. Frequency Error 4.8 KHz
RX Characteristics Min. Typ. Max. Unit
4 Minimum Input Level Sensitivity
1) 1Mbps (FER 23%) -96 -90 dBm
2) 2Mbps (FER :sn/o) -94 -88 dBm
3) 5.5Mbps (FER em) -90 -86 dBm
4) 11Mbps (FER 28%) -88 -84 dBm
5 Maximum Input Level (FER 28%) -8 -5 dBm
3.2 802.11g Mode
Spelelcatlon |EEE802.11g
Mode OFDM
sci
SESSPGFSNB
11n USB Wi-Fi Module with S9083
Channel CH1-CH11
Data rate 6,9, 12, 18, 24, 36, 48, 54Mbps
TX Characteristics Min. Typ. Max. Unit
1. Power Levels
1)Target 3.5 16.5 17.0 dBm
2. Spectrum Mask @ target power
1)atfc +/-11MHz Pass
2) at to +/-20MHZ pass
3) at to > +/—30MHz pass
3 Constellation Error(EVM)@ target power
1)6Mbps -31.2 dB
2) 9Mbps -3o.a dB
3)12Mbps -31.0 dB
4) 18Mbps -30.7 dB
5) 24Mbps -3o.9 dB
6) 36Mbps -3o.e dB
7) 48Mbps -30.5 dB
8) 54Mbps -30.4 dB
4 Frequency Error 4.8 KHZ
RX Characteristics Min. Typ. Max. Unit
5 Minimum Input Level Sensitivity
1)6Mbps (PER 210%) -91 -87 dBm
2)9Mbps (PER 210%) 459 -85 dBm
3) 12Mbps (PER 210%) -86 -82 dBm
4) 18Mbps (PER 210%) 784 280 dBm
5)24Mbps (PER 210%) -81 -77 dBm
6) 36Mbp5 (PER 210%) -79 -75 dBm
7)48Mbp5 (PER 210%) -76 -72 dBm
a) 54Mbps (PER 210%) —74 —70 dBm
sci
SESSPGFSNB
11n USB Wi-Fi Module with S9083
6 Maximum Input Level (PER 2‘ 10%) -8 -5 dBm
3.3 802.11n HT20 Mode
Specmcation IEEE802.11n HT20 @ 2.4GHz
Mode OFDM
Channel CH‘l-CH‘H
Data rate (MCS index) MCSO/1/2/3/4/5/6/7
TX Characteristics Min. Typ. Max. Unit
1. Power Levels
1)Target 3.5 13.0 13.5 dBm
2. Spectrum Mask @ target power
1)at fc +l—11MHZ Pass
2) at to +/-2OMHz Pass
3) at tc > +/—30MHz Pass
3. Constellation Error(EVM)@ target power
1) MCSO -33.2 dB
2) MCS1 -33.1 dB
3) MCSZ -32.9 dB
4) M083 -33.5 dB
5) M084 -33.1 dB
6) MCSS -33.8 dB
7) MCSG -33.6 dB
8) MCS7 -33.1 dB
4. Frequency Error 4.8 KHZ
RX Characteristics Min. Typ. Max. Unit
5. Minimum Input Level Sensitivity
1) MCSO (PER 210%) -90 -87 dBm
2) MCSl (PER :10%) -86 -83 dBm
5d
SESSEGFSNB
11n USB Wi-Fi Module with S9083
3) MCSZ (PER :10%) -84 -81 dBm
4) MCSB (PER S10%) -79 -76 dBm
5) Mcs4 (PER E1004) —77 —74 dBm
6) M085 (PER E1004) —74 -7‘l dBm
7) MCSG (PER 210%) .73 .70 dBm
8) MCS7 (PER :10%) -72 -69 dBm
6. Maximum Input Level (PER S10%) -8 -5 dBm
3.4 802.11n HT40 Mode
Specification |EEE802.11n HT40 @ 2.4GHz
Mode OFDM
Channel CH3—CH9
Data rate (MCS index) MCSO/1/2/3/4/5/6/7
TX Characteristics Min. Typ. Max. Unit
1. Power Levels (Calibrated)
1) 13dBm Target 5.5 16.0 16.5 dBm
2. Spectrum Mask @ target power
1)atfc +l—22MHZ Pass
2) at it: +/-40MHz Pass
3) at to > +/-60MHZ Pass
3. Constellation Error(EVM)@target power
1) MCSO -34.1 dB
2) MC81 -33.7 dB
3) MCSZ -33.4 dB
4) MCS3 -33.5 dB
5) MCS4 -33.2 dB
6) MC85 -34.2 dB
7) MCSG -33.8 dB
5C, 57837GESNB
lln USB Wi-Fi Module with $9033
8) MCS7 - 33.6 dB
4. Frequency Error 4.8 KHz
RX Characteristics Min. Typ. Max. Unit
5. Minimum Input Level Sensitivity
1) MCSO (PER 210%) -88 -84 dBm
2) MCS1 (PER 210%) -84 -80 dBm
3) Mcsz (PER §1o%) -81 -77 dBm
4) M083 (PER é10%) -77 -73 dBm
5) MCS4 (PER 210%) .74 .70 dBm
6) MCSS (PER é10%) -70 -66 dBm
7) MOSS (PER é10%) -69 -65 dBm
8) Mcs7 (PER §1o%) 433 -64 dBm
6. Maximum Input LeveI(PER E 10%) -8 -5 dBm
4. Power
|EEE802.11b
DSSS/CCK
2412~2484MHZ
1. 2. 5.5, 11Mbps
|EEE802.11g
OFDM
57837GESNB
1113 USB Wi-Fi Module with $9083
2412~2484MHZ
6, 9, 12, 18, 24, 36, 48, 54Mbps
315
250
mA
140
70
|EEE802.11n
OFDM
2412~2484MHZ
6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps
310
240
mA
145
72
Power down 36 uA
DTM1, LDO 21
DTM3, LDO 7.4
mA
DTM1, DCDC 18.5
DTM3, DCDC 6.2
Connected state, no data is
133
transmitted LDO,DCDC mA
Connected state, no data is 66
10
5783 iGESNB
lln USB Wi-Fi Module with $9083
transmitted,DCDC
Connection status, transmit small
138
amounts of data,LDO
mA
Connection status, transmit small
74
amounts of data,DCDC
5. Antenna matching
PING RF antenna connection, please refer to the specific needs of the project design.
AN:
,7 .1-7Tfio
Figure 3.Antenna matching
Module and the antenna are away from noise sources claim, and the antenna module to require as a
whole.
P|N6 to WIFI module RF interface between the antenna and cabling requirements coplanar impedance of
500, recommend the use of arcs and lines, as short as possible.
C1, 02, 03 composed of n-type matching network and close to the antenna interface design, the specific
adjustments based on the measured effects and recommended antenna layout design.
C1 = 10pF
Caution:
All platforms must follow this antenna design when using this module. If not follow completely, the FCC
authorization is no longer considered valid.
11
beau.
25,2
2i
uszmsuw
2.622 Z<4>>
mzmm0.mm.m
5C, 57837GESNB
lln USB Wi-Fi Module with $9033
6. Welding conditions
'C
300
fit‘lfillx'all
235»250‘C
250
240
217
200
150
100
B¥ ilfirt':
.3;5;C_'ses; ‘
50
NW
0 >
so too 150 200 250 300 S
Figure 7. Welding temperature curve
1.Temperature range: temperature: <150 'C, time: 60 ~ 90 seconds, slope control in the 1 ~ 3 “C / S
between.
2.Preheat temperature zone: temperature: 150 '0 ~ 200 “C, time: 607120 seconds, the slope between
0.3-0.8.
3.Reflow soldering area: peak temperature 235 'C ~ 250 ”C (recommended peak temperature <245 'C),
time 30-70 seconds.
4.Cooling zone: temperature: 217 “C ~ 170 'C, the slope of 3 ~ 5 ”C (S between.
5.The solder is Sn [M & Cu Lead-free solder (SAC305) for tin-silver-copper alloy lead-free solder.
NOTE: The reflow profile should seek to balance the quality of the solderjoints without compromising the
board and components.
12
SCI
57837GESNB
lln USB Wi-Fi Module with $9033
7 Version
2016-06-06 1.0 Document Draft
2016-06-08 1.1 Initial documents
2016-06-09 1.2 Increasing the RF characteristics of the test data
2016-07-09 1.3 Update RF characteristics of the test data
2016-07-15 1.4 Increase the power consumption test data
2016-09-01 1.5 Update power test data
13
5C, SeSSeGF/SNB
11n USB Wi-Fi Module with S9083
Compliance Information
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This device must accept any interference received, including interference that may cause undesired
operation. Product that is a radio transmitter is labeled with FCC ID.
FCC Caution:
(1) Exposure to Radio Frequency Radiation. This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter. End-users and installers must be
provided with antenna installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.
(2) Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.
(3) This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
(4) Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment
The equipment must not be co-Iocated or operating in conjunction with any other antenna or
transmitter.
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop
configurations or co-Iocation with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
The antenna gain which being use as below:
Antenna Type Manufacturer MIN Max Peak Gain
Dipole Antenna Cortec Technology Inc. AN2400-1761BRS 3dBi
14
5C, SeSSeGF/SNB
11n USB Wi-Fi Module with S9083
General OEM integration instructions:
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and
the transmitter module may not be co-located with any other transmit or antenna. The module shall
be only used with the dipole antenna(s) that has been originally tested and certified with this module.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirement with this module installed(for example . digital device emission . PC
peripheral requirements. etc.)
Additional OEM integration instructions Requirement:
a) Trace layout and dimensions including specific designs for each type:
1) Layout of trace design, parts, antenna, connectors, and isolation requirements;
2) Boundary limits of size, thickness, length, width, shape(s), dielectric constant, and impedance
must be clearly described for each type of antenna;
3) Different antenna length and shapes affect radiated emissions, and each design shall be
considered a different type; e.g., antenna length in multiple(s) of frequency wavelength and antenna
shape (traces in phase) can affect antenna gain and must be considered;
4) The above data is to be provided by a Gerberfile (or equivalent) for PC layout.
b) Appropriate parts by manufacturer and specifications.
c) Test procedures for design verification.
If you have some technology problem, please contact with us.
Address: 1355 jinji lake in suzhou industrial park avenue 9 b international science and technology
park of science and technology square
Telephone: +86-0512—62620006
Fax: +86-0512-62620002
Mail: Company@sci-inc.com.cn
15
SeSSeGESNB
lln USB Wi-Fi Module with S9083
End product labeling:
This transmitter module is authorization only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: 2AKCE-8836ESNB or Contains FCC ID:
2AKCE-SS3GESNB”
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user's manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as show in
this manual.
Caution:
The module is only restricted on this product (Detail information show as below)
Manufacturer: lfiéfillfil’fiilfifll’ifilfiflm
Product name: NEXBOX
Product Model Number: A95X-B7N
16
$783 rGESNB
lln USB Wi-Fi Module with $9083
17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Warning                         : Info object (148 0 obj) not found at 1669336

EXIF Metadata provided by EXIF.tools