VF81086(REV.02 06 10) FANG 24T 26T 28T Operator Manual
2016-04-11
: Sweepscrub Fang 24T - 26T - 28T Operator Manual FANG_24T_-_26T_-_28T_operator_manual 1246 file product_file
Open the PDF directly: View PDF 
.
Page Count: 28
| Download | |
| Open PDF In Browser | View PDF |
REV:07 2015.10.29 TABLE OF CONTENTS SAFETY PRECAUTIONS MACHINE COMPONENTS MACHINE SET UP MACHINE INSTALLATION MACHINE OPERATION TANK DRAINING BATTERY CHARGING PREVENTATIVE MAINTENANCE MACHINE STORAGE BASIC TROUBLESHOOTING PARTS BREAKDOWNS AND LISTS WIRING DIAGRAM 3 4 5 5-6 6 7 7-8 8-9 9 10 11-27 28 2 SAFETY PRECAUTIONS WHEN SERVICING MACHINE: (con’t) Disconnect batteries prior to working on machine. Wear gloves when handling batteries or battery cables. Avoid any contact with battery acid. Avoid moving parts. Do not wear loose fitting clothing while servicing machine. This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only with recommended accessories. All operators shall read, understand and exercise the following safety precautions: 1) DO NOT OPERATE MACHINE: Unless trained and authorized. Unless you have read and understand the operators manual. In flammable or explosive areas. If not in proper operating condition. In outdoor areas. : Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging. : Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks. 2) BEFORE OPERATING MACHINE: Make sure all safety devices are in place and operate properly. : Flammable materials or reactive metals can cause explosion or fire. Do not pick up. 3) WHEN USING MACHINE: Go slow on inclines and slippery surfaces. Follow all safety guidelines. Be very careful when using the machine in reverse. Report and fix any damage to machine prior to operating it. 4) BEFORE LEAVING OR SERVICING MACHINE: Stop machine on level ground. Turn machine off. 5) WHEN SERVICING MACHINE: Read operators manual thoroughly prior to operating or servicing this machine. Use manufacturer supplied or approved replacement parts. Secure machine with wheel blocks prior to jacking the machine up. Use approved jack or hoist to safely elevate the machine. 3 MACHINE COMPONENTS 1 2 3 4 5 31 7 6 20 21 8 19 30 9 18 29 17 10 16 22 11 15 28 23 14 24 27 25 12 13 26 1. Main power ON/OFF switch 2. Vacuum ON/OFF switch 3. Battery level meter 4. Brush ON/OFF switch 5. Brush pressure meter 6. Solution ON/OFF switch 7. Brush pressure UP/DOWN switch 8. Solution control knob 9. Speed control knob 10. Circuit breakers 11. Recovery tank drain hose 12. Squeegee adjustment nut & shaft 13. Squeegee assembly 14. Scrub head actuator 15. Solution tank level sight tube 16. Console adjustment levers 17. Rear solution fill 18. Reverse switch 19. Squeegee lift lever 20. Control housing 21. Operating triggers 22. Solution tank 23. Rear casters 24. Transport wheels 25. Scrub head 26. Scrub head skirt 27. Skirt housing latch 28. Protective rollers 29. Front solution fill 30. Recovery tank 31. Recovery tank lid 4 3. Check that squeegee is properly installed. 4. Check that brush / pad is properly installed. MACHINE SET UP & INSTALLATION UNCRATING MACHINE Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: Machine, batteries (x2), squeegee assembly, battery charger, and pad driver. INSTALLING PAD DRIVER OR BRUSH 1. Ensure that the machine is turned off 2. Raise the brush head assembly off the floor by pushing on the brush lift button on the control console. 3. Open the swing away skirts to gain access to the brush head assembly. 4. If using a pad driver, first attach the appropriate pad to the pad driver surface. 5. Mount the pad driver or brush to the drive motor hub by lining up the three studs with the three holes in the drive motor hub. Once in the holes, rotate the driver toward the spring clip to lock driver into place. BATTERY CONNECTIONS The batteries are and charger are shipped separately and will need to be installed and connected as shown in the diagram below. : Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging. 1. Be sure power switch is in the “off” position. 2. Open recovery tank to gain access to battery compartment. 3. Carefully place the two batteries into the compartment as shown in figure below. Place the battery brace at the rear of the two batteries. DO NOT DROP BATTERIES INTO COMPARTMENT! 4. Connect battery cables to posts in numbered order as shown in drawing below. (RED to POSITIVE and BLACK to NEGATIVE) MOUNTING THE SQUEEGEE 1. Pull back on the squeegee lift lever to raise the squeegee bracket up. 2. Loosen the two knobs on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the back) 3. Tighten the knobs securely. 4. Secure the vacuum hose on the pick-up tube of the squeegee. RED BLACK FILLING THE SOLUTION TANK 1. The Fang 24T / 26T / 28T can be filled in two different locations: a. Front fill area for use with a hose or a bucket. b. Rear fill area for use with a hose only. 2. Determine which fill area you would like to use to fill the machine with water. 3. Fill solution tank with up to 17 gallons of water. (water temperature should not exceed 140° F) The clear tube in the back left of the machine has gallon markers to help determine the water level in the solution tank BATTERY BRACE C H AR G ER PLU G 5. Apply a coat or protective spray on the cable connections to prevent battery corrosion. MACHINE SET UP PRE-OPERATION CHECKS 1. Sweep or dust mop the surface to be cleaned. 2. Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING) 5 10. This machine has reverse. In order to activate reverse, there is a toggle switch located on the left side of the control housing. (see machine components, item #18) The toggle switch must be pulled backwards and the red operating triggers must be pressed to activate reverse motion. : If you are filling the solution tank with a bucket, make sure the bucket is clean. This will prevent debris from clogging the lines or solenoid. : Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals. : Do not keep the machine in the same position with the pad / brush spinning, or you could cause damage to the floor. 11. Adjust amount of solution flow by turning the solution control knob. Turn to the right for more solution, or turn left for less solution. (see machine components, item #8) MACHINE OPERATION : Do not operate machine unless you have read and understand this manual. WHILE OPERATING MACHINE 1. Set control housing to a comfortable operating height by squeezing together the two thumb levers directly underneath the housing. (see machine components, item #16) 2. Lower squeegee assembly to the floor by releasing the lift lever from its locked position. (see machine components, item #19) 3. Lower the brush head assembly to the floor by pushing on the brush lift button on the control console. (see machine components, item #7) 4. Turn main power to “on” position. (see machine components, item #1) 5. Turn vacuum motor switch to “on” position. (see machine components, item #2) 6. Turn the brush motor switch to “on” position. (see machine components, item #4) a. Brushes will not spin until the operating triggers are pulled. 7. Turn the solution switch to “on” position. (see machine components, item #6) a. Solution will not begin to flow until the operating triggers are pulled. 8. To begin scrubbing, pull on one or both of the red operating triggers. (see machine components, item #21) When these triggers are pulled, the brush will begin to spin, the solution will begin to flow, and the machine will propel itself. 9. This machine is self-propelled. The speed can be controlled by a dial located on the right side of the control housing. (see machine components, item #9) 1. Occasionally look through the clear recovery tank lid to see if there is any foam build-up. If excessive foam is found, add defoamer to the recovery tank. : Foam must not enter the float shut-off screen, or damage can occur to the vacuum motor. Foam will not activate the machines float shut-off device. 2. Occasionally view the clear tube at the back left of the machine to check the amount of cleaning solution that is left in the machine. 3. Occasionally check the battery level meter. (see machine components, item #3) When meter is in the red, recharge the batteries. : When battery meter is in the red, do not continue to operate the machine. Battery damage may result. 4. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth. : Do not use your fingers to wipe or remove debris from the blades, as injury may occur. 5. When the solution tank runs empty, turn off the brush switch, solution switch and raise the brush head. Keep the squeegee down and continue to vacuum until all the dirty water is picked up. (see TANK DRAINING section to learn how to drain recovery and solution tanks) 6 DRAINING THE SOLUTION (CLEAN) TANK : The brush motors are circuit breaker protected to protect them from damage. If a breaker trips, it can’t be reset immediately. You must first determine what caused the breaker to trip, and allow the motor to cool down before you can reset the breaker. The breakers are located on the back panel of the control housing. : Anytime scrubbing operation is completed, the solution tank should be drained and cleaned. 1. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain. 2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines. 3. With clean water in solution tank, turn machine power on, solution switch “on” and pull the operating triggers. This will allow the clean water to flush through and clean the solution plumbing. 4. Once tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on the hose barb. TANK DRAINING 1. Turn the power off on the machine 2. With the squeegee and brush head in their “up” position, transport machine to approved area for draining tank(s). DRAINING THE RECOVERY (DIRTY) TANK : Anytime scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned. BATTERY CHARGING : Use only approved chargers with the following specifications: Automatic shut off circuit Deep cycle charging Output current of 10 – 20 amps Output voltage of 24 volts : If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shut-off mechanism and cause damage to the vacuum motor. 1. Remove the drain hose from the holder, and place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process. In order to completely empty the recovery tank, hinge open the recovery tank and let it rest on the support stand. 2. Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery tank. Be careful not to spray water into the float shut-off mechanism. : For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. : Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times. When charging the machine, make sure the battery compartment is left open. 1. Place charger and machine in a well ventilated area. 2. Turn machine off. 3. Open recovery tank up, exposing battery compartment 4. Check fluid level in each battery cell. Do not charge batteries unless fluid is slightly covering the battery plates. Do not overfill the batteries. Overfilling may cause the batteries : If you are storing the machine for any period of time, always leave the clear recovery tank lid off the tank so the tank can dry completely and smell fresh. 3. Replace the drain hose plug tightly as soon as you are done draining the tank. 7 to overflow during charging due to expansion. Replace the caps prior to charging. 5. Plug approved charger into grounded wall outlet before plugging the charger into the machine. 6. Plug charger into red charger receptacle located in the front left of the battery 7. compartment. DAILY MAINTENANCE 1. Remove pad driver / brush and clean with approved cleaner. 2. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary. 3. Raise squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position. 4. Remove the float shut-off assembly and rinse it out with clean water. 8. Flip up the recovery tank “kick stand” and gently lay the recovery tank down until it rests on the stand. 9. The charger will automatically begin to charger the batteries, and it will automatically shut down once the batteries are fully charged. 10. Upon completion of charging, first unplug the charger from the wall outlet, and then disconnect the charger from the machine. 11. Check the battery level after charging is complete. If fluid level is low, add distilled water to bring the fluid level up to the bottom of the sight tubes. Replace the caps and wipe the batteries down with a towel. 5. Clean machine with an approved cleaner and a damp towel. 6. Recharge batteries. WEEKLY MAINTENANCE 1. Check fluid level in batteries. 2. Check batteries for loose or corroded cables. 3. Keep battery tops clean from corrosion. MONTHLY MAINTENANCE 1. Check machine for leaks and loose fasteners. 2. Lubricate all grease points and pivot points with silicon spray and approved grease. 3. Place machine over a floor drain. Flush solution system by pouring 3 gallons of hot water and approved alkaline detergent into the solution tank and running machine (with solution control on) for 45 seconds. Turn machine off and let it sit overnight. Then next day, drain the remaining solution and rinse the solution tank out with clean water. PREVENTATIVE MAINTENANCE : Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected! : Repairs are to be completed by Authorized Service Centers only. Any repairs completed by unauthorized persons will void the warranty. VACUUM MOTOR MAINTENANCE 8 1. Contact your local Viper Distributor for any motor maintenance. 2. Vacuum motor should have the brushes checked every 250 hours. Brushes should be replaced when they are worn to a length of 10mm or less. caused by freezing temperatures will not be covered by the warranty. 7. Drain the recovery tank and remove the clear on the top of the recovery tank so that it can “breathe” during storage. 8. Drain the solution tank of all fluid. BATTERY MAINTENANCE : For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. : Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times. : Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times! 1. Always follow the battery charging directions as outlined in the BATTERY CHARGING section of this manual. 2. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS. 3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections. 4. Check battery connections for wear and loose terminals. Replace if necessary. MACHINE STORAGE 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always store the machine in its upright position. 4. Always store the machine with the pad driver / brush raised off the floor. 5. Always store the machine with the squeegee assembly raised off the floor. 6. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage 9 BASIC TROUBLESHOOTING PROBLEM No power CAUSE Bad batteries Batteries need to be charged Loose battery cable Batteries not connected properly SOLUTION Replace batteries Charge batteries (see Battery Charging) Tighten loose cable(s) Follow battery installation instructions Bad brush switch Contact Viper Distributor Brush circuit breaker has tripped Rectifier has burned out Bad wiring Bad brush motor Carbon brushes worn out Bad solenoid Check brush motor for obstructions and reset breaker Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Vacuum motor does not run Bad vacuum switch Contact Viper Distributor Short run time Bad wiring Bad vacuum motor Carbon brushes worn out Batteries need to be charged Batteries need maintenance Bad cell in battery(s) Bad charger Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Charge batteries (see Battery Charging) See Battery Maintenance in this manual Replace batteries Replace charger Little or no solution flow Bad solution switch Contact Viper Distributor Brush motor does not run Clogged solution solenoid Clogged solution filter Solution line obstructed Contact Viper Distributor Remove filter and clean Remove solution line and clean Increase flow by twisting solution adjustment knob to the Solution flow adjustment knob in need right. Decrease flow by twisting solution adjustment knob of adjustment to the left. Poor water pick up Squeegee clogged Clean debris off squeegee with damp towel Squeegee blades worn Install new squeegee blades Confirm that the squeegee assembly is securely fastened Squeegee not mounted correctly to the machine and not loose fitting. Check hose connections and make sure they are firm. Vacuum hoses have a hole or are loose Replace hose if damaged. Vacuum hose may be clogged Check hose for debris and remove any clog. Drain hose stopper is loose Tighten drain plug. Batteries need to be charged Charge batteries (see Battery Charging) Tighten vac motor mounting screws. Do not overtighten or Vacuum motor is loose damage will occur. Recovery tank lid is loose Confirm the clear recovery tank lid is securely in place. Drain recovery tank and tilt tank on side. Check the inlet Recovery tank inlet hole is clogged hole for debris and remove debris. Recovery tank is full Drain recovery tank. Remove float shut off from inside recovery tank and Float shut off is clogged remove any debris. 10 11 FANG 24T,FANG 26T & FANG 28T - SOLUTION TANK ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF81405BD GRIP,HANDLE 1 2 VA13477 SCREW, SELF-TAPPING, ST, M4 X 16 3 3 VV13664 WASHER,PLAIN, M4 X M12 X 1 1 4 VF82154 PLUG,EXPANSION 1 5 VV13604 SCREW, M8 X 20 6 6 VF13519 WASHER,LOCK, 8X20X2 6 7 VF13535 WASHER,PLAIN, M8 X M20 X 2 8 8 VF81406 BUSHING 1 9 VF81404 SUPPORT,RECOVERY TANK 1 10 VF82029A BRACKET,VAC TUBE 1 11 VF82032 SPRING 1 12 VF82030 ADAPTER,TUBE 1 13 VF82031A GASKET,TUBE ADAPTER 1 14 VF82070 LABEL,LEFT 1 15 VF81306 CONNECTOR, 175A 1 16 VF81310 17 VF82123 DECAL 1 18 VF13633 SCREW, M6 X 35 2 19 VV13607 WASHER,LOCK, M6 8 20 GT13032 WASHER,PLAIN, M6 X M16 X 1.5 6 21 VA13516 WASHER,PLAIN, M10 X M30 X 1.5 1 22 VF13495 SCREW, M6 X 16 4 23 VF81715 STANDOFF 2 24 VF82067 BRACKET 1 25 VF14232 SCREW, M6 X 10 2 26 VF82078 SCREEN,FILL 1 27 VF13543 SCREW, SELF-TAPPING, ST, M4 X 16 2 28 VF13544 SCREW, SELF-TAPPING, ST, M4 X 10 6 29 VA13483 WASHER,PLAIN, M4 X M9 X 0.8 7 30 VF82081 PLUG,FILL SCREEN 1 31 VF82079 COVER,FILL SCREEN 1 32 VF83101 SOLUTION TANK 1 33 VF82071 LABEL,RIGHT 1 34 VF99001 WHEEL, 4" 2 35 VF83129 BUSHING 2 36 VF13514A WASHER,PLAIN, M8 X M16.5 X 1 2 37 VF13635 SCREW, M8 X 50 2 38 BAT195I BATTERY,12V,195AMP HOUR 2 39 VF83111 CASTER, 4" 2 40 VF83140 TRAY,BATTERY 1 41 VF82072A SPACER,BATTERY 1 42 VF13634 SCREW, M10 X 30 8 KIT, CONNECT WIRE 12 1 FANG 24T,FANG 26T & FANG 28T - SOLUTION TANK ASSEMBLY DIA NO PART NUMBER 43 VF82050A BUSHING 1 44 VF14248 SCREW, M8 X 100 1 45 CHRGR18 CHARGER,24V,18AMP 1 46 VF13537 WASHER,PLAIN, M10 X M26 X 2 8 47 VF13518 WASHER,LOCK, M10 8 48 VF14234 SCREW, M8 X 16 2 49 VF13513 NUT, M8 2 50 VF81408 PLATE,LOCK 2 51 VF81416 HOSE BARB 2 52 VF82161 CLAMP (16-25) 1 53 VF81123B TUBING 1 54 VF14230 SCREW, M5 X 15 3 55 VV13601 WASHER,LOCK, M5 3 56 VF13532 WASHER,PLAIN, M5 X M11 X 2 3 57 VF81202 PLATE,SQGE,LOCK 1 58 VF14235 SCREW, M8 X 35 1 59 VF48216 WASHER,LOCK, M12.7 1 60 VF83124 HANDLE,SQGE,LIFT 1 DESCRIPTION 13 NO REQ'D FANG 24T, FANG 26T & FANG 28T - RECOVERY TANK ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF82010 CLEAR COVER,RECOVERY TANK 1 2 VF82083 DECAL WARNING BATTERY 1 3 VF82009 ELBOW ADAPTOR,FLOAT 1 4 VV13607 WASHER,LOCK, M6 13 5 VF13533 WASHER,PLAIN, M6 X M16 X 2 7 6 VF14233 SCREW, M6 X 20 4 7 VF81504 FLOAT 1 8 VF83102 RECOVERY TANK (24") 1 9 VF13528 WASHER,TOOTH,LOCK, M6 10 VF13495 SCREW, M6 X 16 2 11 VF82028 CABLE 1 12 VF82010B GASKET 1 13 VF82010X KIT,LID 1 14 VF82010A RUBBER HINGE 1 15 VF81510 DRAIN HOSE 1 16 VV10113 CLAMP, 2" 1 17 VF83154 DECAL,BATTERY INSTALLATION 1 18 ZD54000 MOTOR,VAC 3 STAGE,24VDC 1 19 VF13502 NUT,LOCK, M6 3 20 VF81508 STUD(24") 3 21 VF13521 NUT,M6 3 22 VF81503 SEAT 1 23 VF14200 SCREW, M6 X 16 9 24 GT13032 WASHER,PLAIN, M6 X M16 X 1.5 9 25 VF82011 9) HINGE,RECOVERY TANK 1 26 VF82082 LOGO 1 27 VA13477 SCREW, SELF-TAPPING, ST, M4 X 16 4 28 VV13664 WASHER,PLAIN, M4 X M12 X 1 4 15 2 16 FANG 24T, FANG 26T & FANG 28T - BRUSH LIFT/DRIVE ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF82080 HUB CAP 2 2 VF81106 WHEEL, 8" 2 VF81600 TRANSAXLE, 24" 1 ZD72000A TRANSAXLE MOTOR, 24VDC 1 4 VF81102 BRACKET,TRANSAXLE MOUNT 2 5 VF13537 WASHER,PLAIN, M10 X M26 X 2 6 6 VF13518 WASHER,LOCK, M10 6 7 VF13636 SCREW, M10 X 45 4 8 VF13634 SCREW, M10 X 30 2 9 VF13502 NUT,LOCK, M6 8 10 VF13533 WASHER,PLAIN, M6 X M16 X 2 8 11 VF81103 SPACER 4 12 VF82016A BUSHING 2 13 VF13538 WASHER,PLAIN, M12 X M22 X 2 4 14 VF83136 BRACKET,LIFT DUAL MOTOR 1 15 VF83139 PIN, M10 X 30 2 16 VF14084 PIN,COTTER, M3.2 X 24 2 17 VF81303 18 VF13519 WASHER,LOCK, M8 4 19 VV13604 SCREW, M8 X 20 4 20 VF13535 WASHER,PLAIN, M8 X M20 X 2 4 21 VF83126 BRACKET,CABLE GUIDE 1 22 VF83135 BRACKET,ACTUATOR 1 23 VF83115 PLATE 1 24 VF14247 SCREW, M12 X 25 2 25 VF81137 PLATE,BASE TRANSAXLE 1 26 VF13501 NUT,LOCK, M12 2 3 ACTUATOR 17 1 18 FANG 24T,FANG 26T & FANG 28T - BRUSH/PAD DRIVE ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF83112A BLOCK,GUIDE 1 2 VV20274B WASHER,PLAIN, M13 X M39 X 2 1 3 VA13400 WASHER,PLAIN, M5 X M11 X 1 4 4 GT13022 NUT,LOCK, M5 4 5 VF14234 SCREW, M8 X 16 1 6 VF13519 WASHER,LOCK,M8 9 7 VF13542 WASHER,PLAIN, M8 X M26 X 2 1 8 VF83116A SUPPORT PLATE,SKIRT 1 9 VF13535 WASHER,PLAIN, M8 X M20 X 2 8 10 VF81114 BRACKET,SPRING 1 11 VF83117 SPRING 1 12 VA14303 PIN, M4 X 40 1 13 VF83113A BRACKET,SPRING MOUNT 1 VF81112 BRACKET,MOTOR MOUNT (FANG24T & FANG26T) 1 14 VF83205 BRACKET,MOTOR MOUNT ( FANG28T) 1 15 VF81122 TUBING, 150mm 1 16 VF82040 HOSE BARB,TEE 1 17 VF81121 TUBING, 120mm 1 18 VF82148 CLAMP, 16mm 2 19 VF14225A SCREW, M6 X 40 6 20 VF83133 STUD 6 VF81105 PAD DRIVER, 11" (FANG24T) 2 VF83128 PAD DRIVER, 12" (FANG26T) 2 VF83207 PAD DRIVER,13" (FANG28T) 2 22 VF13502 NUT,LOCK, M6 6 23 VF83118 SPACER 2 24 VF99003A BIG MOUTH 2 25 VA13484 SCREW,SELF-TAPPING,ST, M4 X 12 6 26 MF-VF002-4A SCREW,SELF-TAPPING, 1/4" - 1" 6 21 27 VF14241 SCREW, 5/16" - 1" 2 28 VV20298 WASHER,LOCK, 5/16" 2 29 VF82058 WASHER 2 30 VF83130A PLATE, DRIVE, ASSY 1 31 VF83130 PLATE,DRIVE 2 32 VF83134 STOP,DRIVE RELEASE 2 33 VF83132 SPRING 2 34 VF83131 CLAMP,BRUSH PLATE 2 35 VV13601 WASHER,LOCK, M5 8 36 VF13545 SCREW,SELF-TAPPING,ST,M5 X 10 8 37 VV13604 SCREW, M8X20 8 38 VF14242 SCREW, 3/8" - 1" 8 39 VV13620 WASHER,LOCK, 3/8" 8 40 VF13537 WASHER,PLAIN,M10 X M26 X 2 8 41 VF83114 PIN, M16 X 42 1 42 ZD45407 KEY, 6.35 X 25 2 43 ZD45000 BRUSH MOTOR,24VDC, .75HP 2 44 VF14230 SCREW, M5 X 15 4 19 20 FANG 24T, FANG 26T & FANG 28T - SOLUTION CONTROL ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 VF14245 SCREW, M5 X 6 2 2 VF82036 SHAFT 1 3 VV13650 SCREW, M4 X 10 1 4 VF13532 WASHER,PLAIN, M5 4 5 VV13601 WASHER,LOCK, M5 4 6 VF14230 SCREW, M5 X 15 2 7 VF13536 WASHER,PLAIN, M9.8 X M16 X 1 2 8 VF82075 NUT, 3/8" 2 9 VF83121 CABLE,SOLENOID 1 10 VF82148 CLAMP, 16mm 14 11 VF82040 HOSE BARB,TEE 1 12 VF81134 TUBING, 50mm 2 13 VF82042 ELBOW 2 14 VF81124 TUBING, 115mm 1 15 VF81403A ELBOW,SOLUTION TANK 2 16 VF81780 TIE 2 17 VF82168-1 HOSE BARB, FILTER 2 18 VF82168-3 SEAT,FILTER 1 19 VF82168-4 SCREEN,80SS,FILTER 1 20 VF82168-5 GASKET,FILTER 1 21 VF82168-2 COVER,FILTER 1 22 VF82168 FILTER, ASSY 1 23 VF81125 TUBING, 200mm 1 24 VF81126 TUBING, 80mm 1 25 VF13495 SCREW, M6 X 16 4 26 VF13533 WASHER,PLAIN, M6 X M16 X 2 4 27 VF81127 TUBING, 65mm 1 28 VF82033-24 SOLUTION VALVE SOLENOID,24VDC 1 29 VV13607 WASHER,LOCK, M6 2 30 VF83120 BRACKET,SOLENOID 1 31 VF13502 NUT,LOCK, M6 2 32 VF81128 TUBING, 320mm 1 33 VV20509 SCREW,M5X10 2 34 VF81118 CLAMP 2 35 VF13540 WASHER,WAVE, M12 1 36 VF82037 BRACKET,DRAIN HOSE & VALVE 1 37 VF82069 LABEL,VALVE 1 38 VF82074 BUSHING 1 39 VF82038 KNOB,VALVE ADJUST 1 21 22 FANG 24T,FANG 26T & FANG 28T - BRUSH SKIRT ASSEMBLY DIA NO PART NUMBER DESCRIPTION NO REQ'D VF81109 BUMPER (FANG 24T) 1 VF83105 BUMPER (FANG 26T) 1 VF83203 BUMPER (FANG 28T) 1 2 VF13495 SCREW, M6 X 16 8 3 VV13607 WASHER,LOCK, M6 8 4 VF13533 WASHER,PLAIN, M6 8 5 VF83107 BRACKET,SKIRT MOUNT 2 6 VF83108 PIN,SKIRT 2 7 VF82013 WHEEL, 3" 2 1 8 VF82055 BUSHING 2 9 VF13514A WASHER,PLAIN, M8 X M16.5 X 1 2 10 VF14236 SCREW, M8 X 40 2 11 VA13474 SCREW, M5 X 16 18 12 VF13550 WASHER,PLAIN, M5 X M25 X 1.5 4 VF81130 CLAMP,BUMPER (FANG 24T) 2 VF83151 CLAMP,BUMPER (FANG 26T) 4 VF83204 CLAMP,BUMPER (FANG 28T) 2 VA13400 WASHER,PLAIN, M5 X M11 X 1 14 VF81117 GRIP,BUMPER (FANG 24T) 2 VF83147 GRIP,BUMPER (FANG 26T) 4 VF83212 GRIP,BUMPER (FANG 28T) 2 VF81131 CLAMP,BUMPER (FANG 24T) 2 VF83213 CLAMP,BUMPER (FANG 28T) 2 VF81109A BUMPER (FANG 24T) 1 VF83105A BUMPER (FANG 26T) 1 VF83203A BUMPER (FANG 28T) 1 VF81108R RIGHT SKIRT,ASSEMBLY (FANG 24T) 1 VF83104R RIGHT SKIRT,ASSEMBLY (FANG 26T) 1 VF83202R RIGHT SKIRT,ASSEMBLY (FANG 28T) 1 VV20519 SCREW, M4 X 8 4 13 14 15 16 17 18 19 VF81108 SKIRT,RIGHT (FANG 24T) 1 20 VF83104 SKIRT,RIGHT (FANG 26T) 1 VF83202 SKIRT,RIGHT (FANG 28T) 1 21 VF83109 LATCH,HOOD 1 22 VV20291 WASHER,LOCK, M4 4 VF81107 SKIRT,LEFT (FANG 24T) 1 VF83103 SKIRT,LEFT (FANG 26T) 1 VF83201 SKIRT,LEFT (FANG 28T) 1 VF83142 BLOCK,SKIRT 2 VF81107L LEFT SKIRT,ASSEMBLY (FANG 24T) 1 VF83103L LEFT SKIRT,ASSEMBLY (FANG 26T) 1 VF83201L LEFT SKIRT,ASSEMBLY (FANG 28T) 1 23 24 25 23 24 FANG 24T, FANG 26T & FANG 28T - CONTROL HOUSING DIA NO PART NUMBER DESCRIPTION NO REQ'D 1 2 3 4 5 VF13491 VF14122 VF14121 VF13502 GT13032 VF81781 VF81781-X VF81726A VF81734 VF83149 VF82301 VF81713 VF82305 VF14078 VA50477 VF81718 VF82313 VF13495 VF81719 VF83137A VF81708A VF83138A VF83209A VF81721 VF81727 VF81725 VF14200 VF81730 VF81709 VF81716 VF81710 VF81732 VF82316 VF81739-24T VF81115 VF83145 VF83210 VF83148 VF82303A VF81703 VF82312 VF99012 VF82107BD VF81711 VF81712 VF13514A VF82106BD VF14212 VF13511 VF44203 VF81707 VV13652 VF81714 VF82153 VF82160 VF81744B VF81722 SCREW, M4 X 12 WASHER,PLAIN, M10 X M20 X 2 SCREW, M10 X 65 NUT,LOCK, M6 WASHER,PLAIN, M6 DIODE, 400V DIODE WITH ENDS SOLENOID, 24V BREAKER,CIRCUIT, 35 AMP LABEL,CIRCUIT BREAKER HOUSING,CONTROL BUSHING LABEL,SPEED CONTROL SCREW,M3 X 10 WASHER,PLAIN, M3 X M10 X 1 LIGHTS,BATTERY CAPACITY GASKET SCREW, M6 X 16 SPACER PANEL,SWITCH (24") LABEL,SWITCH (FANG 24T) LABEL,SWITCH (FANG 26T) LABEL,SWITCH (FANG 28T) SWITCH,LIGHTED ROCKER GAUGE,BRUSH PRESSURE SWITCH,BRUSH LIFT SCREW, M6 X 16 KNOB,SPEED CONTROL PIN,HANDLE LOCK SPRING PIN,HANDLE ADJUSTMENT POTIENTIOMETER, 4.7K PLATE SPEED CONTROL,BOARD SERIAL TAG (FANG 24T) SERIAL TAG (FANG 26T) SERIAL TAG (FANG 28T) LABEL,CIRCUIT BREAKER PANEL,CONTROL HOUSING BATTERY CAPACITY CONTROL,BOARD GASKET BREAKER,CIRCUIT, 12 AMP HANDLE,RIGHT BOLT,SHOULDER, M8 X 15 X M6 SPRING WASHER,PLAIN, M8 X M16.5 X 1 HANDLE,LEFT SCREW, M3X25 WASHER,TOOTH, M3 SWITCH ASSY BRACKET,SWITCH (24") NUT,LOCK, M3 TUBE,HANDLE,ADJUSTMENT SWITCH,KEY LABEL,KEY SWITCH STRAIN RELIEF,CORD SWITCH,TOGGLE 7 2 2 10 6 3 3 3 3 1 1 2 1 6 6 1 1 4 6 1 1 1 1 4 1 1 12 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 2 1 1 2 1 1 1 1 1 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 25 PARTS LIST FANG 24T, FANG 26T & FANG 28T - SQUEEGEE ASSEMBLY 26 FANG 24T,FANG 26T & DIA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 PART VF13501 VF13538 VF82172 VF13637 VF84231 VF14547 VF81243 VF82112 VF81203A VF83150 VF85104 VF85336 VF85103 VF81210 VF14236 VF13514A VF82055 VF82013 VF81201 VF81231 VF81206 VF81216 VF81237 VF81235 VF81218A VF81209 VF14310 VF81208 GT13022 VF81222 VF81219 VF13535 VV20203 VF81214 VF81233 VF81214A VF81233A VF81205 VF81215 VF81236 VF81234 VF81213 VF81232 VF82121 VF13502 VF14503 VF13521 VF85106 VF81008A VF81008B VF14516 VF13542 VF84225 VF14527 VF84228 VF84227 VF83500 FANG 28T - SQUEEGEE ASSEMBLY DESCRIPTION NUT,LOCK, M12 WASHER,PLAIN, M12 X M26 X 2 LOCK SPRING SCREW, M12 X 130 FRONT SQUEEGEE SUPPORT NUT LOCK M10 CABLE,SQGE,LIFT (24") BUSHING HOSE HOLDER,"U" HOSE HANDWHEEL M8x55 WASHER NYION SQUEEGEE SUPPORT PIN KNOB, M8 SCREW,M8 X 40 WASHER,PLAIN, M8 X M16.5 X 1 BUSHING WHEEL, 3" HOUSING,SQUEEGEE (FANG 24T & 26T) HOUSING,SQUEEGEE (FANG 28T) BLADE,SQUEEGEE,REAR,PU (FANG 24T & 26T) BLADE,SQUEEGEE,REAR,NEOPRENE (FANG 24T & 26T) BLADE,SQUEEGEE,REAR,PU (FANG 28T) BLADE,SQUEEGEE,REAR,NEOPRENE (FANG 28T) LATCH,HOOD HOOK,REAR SQUEEGEE BACKUP ADJUSTMENT SCREW, M5 X 70 RIVET, M4 X 5 NUT,LOCK, M5 BOLT,SHOULDER, 5/16" X 1.25" WHEEL, 2" WASHER,PLAIN, M8 X M20 X 2 NUT,LOCK, 5/16" BACKUP STRIP,SQUEEGEE,REAR (FANG 24T & 26T) BACKUP STRIP,SQUEEGEE,REAR (FANG 28T) KIT,BACKUP STRIP (FANG 24T & 26T) KIT, BACKUP STRIP (FANG 28T) BLADE,SQUEEGEE,FRONT,PU (FANG 24T & 26T) BLADE,SQUEEGEE,FRONT,NEOPRENE (FANG 24T & 26T) BLADE,SQUEEGEE,FRONT,PU (FANG 28T) BLADE,SQUEEGEE,FRONT,NEOPRENE (FANG 28T) BACKUP STRIP,SQUEEGEE,FRONT (FANG 24T & 26T) BACKUP STRIP,SQUEEGEE,FRONT (FANG 28T) KNOB, M6 NUT,LOCK, M6 NUT LOCK M8 NUT, M6 SPACER 8x10x7 SQUEEGEE ASSY (FANG 24T & 26T) SQUEEGEE ASSY (FANG 28T) NUT LOCK M8 WASHER PLAIN ￠8.4X￠26X2 BACK SQUEEGEE SUPPORT SEREW SHOULDER M10 SEREW SHOULDER M8 SQUEEGEE SUPPORT KIT, SQUEEGEE BRACKET ASSEMBY 27 NO 3 1 1 1 2 2 1 1 1 1 1 1 1 3 4 2 2 2 1 1 1 1 1 1 1 1 1 2 1 3 3 3 3 1 1 1 1 1 1 1 1 1 1 6 1 1 1 4 1 1 2 2 1 1 2 1 1 WIRING DIAGRAM FOR FANG 24T, FANG 26T & FANG 28T 3 (16AWG WHT) BATTERY CAPACITY LIGHTS 9 (12AWG RED) (12AWG RED) 0 (16AWG BLU) AMMETER MAIN SWITCH 3 (16AWG WHT) 4 2 4 VACUUM SWITCH 6 BRUSH SWITCH 7 SOLUTION SWITCH (16AWG WHT) 3 (14AWG RED) 01 (14AWG BLK) 15 (14AWG RED) 16 (14AWG BLK) F R SPEED CONTROL BOARD (12AWG RED) 10 (12AWG RED) 8 (12AWG RED) 17 (16AWG BLU) 18 (16AWG BLU) (16AWG GRN) SOLUTION SOLENOID 17 18 (16AWG BLU) 35AMP 0 (16AWG BLU) MAIN CIRCUIT BREAKER (16AWG WHT) 12AMP 10 02 (16AWG GRN) 4.7K 2W B+B- M2 M1 2 (12AWG RED) 7 DIRECTION SWTICH KEY SWITCH 8 DOWN 5 (16AWG GRN) 13 UP ACTUATOR (16AWG WHT) 1 0 (16AWG WHT) (16AWG WHT) TRIGGER SWITCH 7 3 (16AWG BLU) ACTUATOR MOTOR 10 RIGHT BRUSH CIRCUIT BREAKER 03 (12AWG RED) 0 (16AWG BLU) 0 (16AWG BLU) 6 10 9 (12AWG RED) 03 (12AWG RED) 9 (12AWG RED) BRUSH SOLENOID (12AWG BLK) LEFT BRUSH MOTOR 35AMP LEFT BRUSH CIRCUIT BREAKER 3 (12AWG BLK) RIGHT BRUSH MOTOR 14 B B 04 (14AWG RED) PCB (14AWG BLK) VACUUM MOTOR 15 16 (14AWG RED) (16AWG WHT) 1 (12AWG RED) 8 DRIVE MOTOR (14AWG BLK) CHARGER PLUG (6AWG BLK) (6AWG RED) (12AWG RED) 8 (12AWG RED) 11 4 (16AWG WHT) (14AWG RED)12 0 (16AWG BLU) (16AWG BLU) 0 14 (14AWG RED) (14AWG BLK) 01 (16AWG GRN) 02 (14AWG BLK) 04 12 (14AWG RED) (16AWG BLU) 0 (12AWG BLK) 03 CHARGER PLUG 11 (12AWG RED) 35AMP (14AWG RED) VACUUM CIRCUIT BREAKER 3 (16AWG WHT) (6AWG RED) (6AWG RED) VACUUM SOLENOID (12AWG BLK) 03 0 (16AWG BLU) 12V BATTERY 13 (14AWG RED) (6AWG BLK) 12V BATTERY 28 MAIN SOLENOID
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : adm Create Date : 2011:12:21 15:26:14Z Modify Date : 2016:04:11 09:06:46-05:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : adm Title : VF81086(REV.02 06-10).pdf Creator Tool : Adobe Acrobat 8.0 Metadata Date : 2016:04:11 09:06:46-05:00 Producer : GPL Ghostscript 8.15 Document ID : uuid:13463f31-1483-407e-93c4-438a98fe7215 Instance ID : uuid:8b465932-5b18-444f-a85f-2fe4f3328156 Page Count : 28EXIF Metadata provided by EXIF.tools