Sweepscrub Powr Flite Pfx1350 Carpet Extractor Parts List User Manual

PFX1350 &file=PFX1350

User Manual: Sweepscrub Powr-Flite-Pfx1350-Carpet-Extractor-Parts-List powr-flite-pfx1350-carpet-extractor-parts-list 2498 file product_file sweepscrub

Open the PDF directly: View PDF .
Page Count: 7

7

MODEL PFX1350 SERIES CARPET EXTRACTOR PARTS

ref# order# description

1X9113 housing, recovery tank

2PX25 fitting, plastic, hose barb

3PX14A dump valve gasket rubber

4PX11A fitting, plastic elbow

572486A spacer, 1.625 long, .50 od, .313 id

6X8025 wheel, black, 4” x 1-1/4”

772645A bolt, 5/16-18 x 2-1/4, hex

8PX103G gasket, lid, 8”od x 6-5/8 id x 1/8” thick

9PX103 lid, screw-in, 6” clear w/ black ring

10 72656A hose, 1-1/2”, wire-reinforced, black

11 X8295 screw, black zinc

12 PX33 vacuum tube

13 PX31 float cage w/ heavy ball

14 72615A coupling, pvc, 1-1/2 slip x slip

ref# order# description

15 X9154 pipe, pvc, schedule 40, 1-1/2”, 9.5” long

16 PX63 coupler, plastic, 1- _” slip

17 PX87 rocker switch

18 X8102 neon light w/ lens, orang

19 72387A screw, #8 x 5/8 phil ph black

20 PX86 indicator light, green, 250v

21 X9152 switch panel w/o heater

X9130 switch panel w/ heater

22 PAS36 expansion plug drain

23 PAS37 drain hose

24 7DL005 clamp worm gear 1-1/2 ss

25 X8235 washer, _” flat, uss zinc

26 7GR016 elbow, 1-1/4h - 1-1/4m, nylon

PFX1350 recovery tank assembly

8

MODEL PFX1350 SERIES CARPET EXTRACTOR PARTS

PFX1350 base assembly

9

MODEL PFX1350 SERIES CARPET EXTRACTOR PARTS

ref# order# description

1X9112 housing, solution tank

2X9014 hinge

37BS003 screw, phil pan ms, 18-8 ss

4PX3H hose, solution, 3/8" id x 1/8" wall

5PX42 clamp, 5/8 worm gear

6PX85 fitting, hose male/male barb

7PX17 street elbow, 45° brass, 1/4" npt

8PX48 fitting, brass, bulkhead, 3/4

972274A washer, 3/4"

10 PX48G gasket, fiber

11 71495A pump protection filter

12 7CT002 bolt, 5/16-18 x 1" hex tap

13 PX88 grommet

14 7CM002 washer, flat #8 ss, toggle valve

15 X9140 tie down plate

16 7CP002 bolt, 5/16-18 x 1/2" hex tap

17 7BH004 screw, 10-32 x 3/8" phil pan ms

18 72173A spring clip, black vinyl coated

19 X8218 washer, 5/16 sae flat zinc

20 X9149 gasket, foam strip

PFX1350 solution tank assembly

ref# order# description

172620AB housing, base, black

272633A axle

3X9066 wheel, 12" x 1.75" non-marking,

PX106B wheel, 12" w/ 3/4" bore, all black

47GL002 push nut

57CM007 washer, 1/2 uss flat, 18-8 ss

672634A bushing, 1/2" id x 3/4" od x 2-1/4" long

72635A spacer, 1/2" id x 3/4" od x 1/4" long

772640A gasket, vac manifold, long

872623A cover, vacuum manifold, long

97CW002 screw, #6 x 3/4 phil pan ts, type a 18-8 ss

10 72000A rod, 3/16 x 5-1/2, all thread stud, 18-8 ss

11 72657A screw, 10-24 x 4" long, hex head

72658A screw, 10-24 x 5" long, hex head

12 72651A spacer, vac motor, 2.375" long

13 70020B gasket, vacuum motor seal

14 1942-IE vacuum motor, 115 vac, 104 cfm, 2 stage

72365A vacuum motor, 3 stage, 120v

15 7BF003 nut, kep, #10-24 zinc

16 7CM003 washer, #10 uss flat, 18-8 ss

17 72624A cover, vacuum manifold, short

18 72641A gasket, vac manifold, short

19 PX117A gauge, 0-300 psi, 2-1/2", abs

PC38 connector, double thread

20 72638A pressure regulator plate

X9157 cover, pressure regulator plate

21 72173A spring clip, black vinyl coated

22 72636A cover plate, bottom

23 72388A screw, #10 x 5/8, tap phil, ss pan head

24 PX65 caster, 4" black

ref# order# description

25 72490A screw, 5/16-18 x 5/8, cap screw w/ hex socket

26 72387A screw, #8 x 5/8, black, tap phil, pan head

27 72639A gasket, mounting pressure regulator

28 X8256 nut, 8-32 keps, zinc

29 70063B coupler, valved 1/4, quick disconnect

30 7CX002 nipple, hex 1/4 mpt

31 72115A washer, 5/8 x 1-3/16, bonded seal, galvanized

32 PC38 connector, double thread, female

33 72642A gasket, vac manifold, circle

34 72625A cover, vacuum manifold, circle

35 72627A gasket, pump mounting

36 72626A pump mounting plate

37 X9069 end loop, ss, w/ 2 holes, 16g

38 PF1750 heater unit, 1750 watts

PF1200 heater, 1200w for low flow

PF2000 heater, 2 1000 watt element (split)

39 PT400 pump, 200 psi w/regulator, 115v

SF814 pump, 100 psi w/by-pass, epdm valves

PT400-KIT3 pump assembly, 400 psi w/ hoses

40 X9022 heater mounting bracket

41 X8236 screw, 10-24 x 1-1/4", phil pan ms, zinc

42 72020A screw, #12 x 1", self-tap, phms zinc

43 7BS003 screw, 1/4-20 x 1/2, phil, pan , ms 18-8 ss

44 X9014 hinge

45 PD8 strain relief, 1/2" npt

46 PX112 pigtail, black, 12/3 sjt x 39" long

47 PR112R pigtail, red, 12/3 sjt x 39" long

48 X9131 cord panel

49 X8008N nut, lock, 1/2" steel conduit

50 7BS002 screw, 8-32 x 1/2 phil, pan ms, 18-8 ss

PFX1350 base assembly

XXXXX 06/2005

3101 Wichita Court ■Fort Worth, TX 76140 ■800.880-2913 ■www.Powr-Flite.com

S

eries

Perfect Heat

Perfect HeatTM Plus System

WARNING! The Perfect HeatTM Plus System can produce very hot water that could damage some delicate

fabrics and fibers. Please ensure the surface being cleaned will not be damaged by hot water up to 200 degreEs

Fahrenheit.

This machine is equiped with the Perfect HeatTM Plus System for heating the cleaning solution. This system uses a com-

bination of the patent pending Perfect HeatTM coils and an inline electrical heater.

Operation:

1. Follow operating instructions steps for filling the machine with water and cleaning solution.

2. Turn on electrical heater, switch is located on panel.

3. Pre-heat machine for 5-10 minutes before use.

NOTE: There is a valve in the upper compartment that either sends the water through the heating components, or

bypasses them. The machine is preset in the “HOT” position. To clean with cold water, turn the valve to “COLD” or UP

position. This should be done prior to filling the tank with water.For general cleaning, it is recommended leaving the

valve in the “HOT” or down position and cleaning with hot water.

switch panel valve

Ref # Part # Description Qty

01 72620AB Housing, Base, Black 1

02 72633A Axle, 23.375” Long 1

03 X9066+ Wheel, 12" x 1.75" Non-Marking, Gray Tire on Black Wheel 2

04 7GL002 Push Nut 2

05 7CM007 Washer, 1/2 USS Flat, 18-8 SS 6

06 72635A Spacer, 1/2" ID x 3/4" OD x 1/4" Long 2

07 72640A Gasket, Vac Manifold, Long 2

08 72623A Cover, Vacuum Manifold, Long 2

09 7CW002 Screw, #6 x 3/4 Phil Pan TS, Type A 18-8 SS 26

10 72000A Rod, 3/16 x 5-1/2, All Thread Stud, 18-8 SS 1

11 72658A Screw, 10-24 x 5" Long, Rnd Slot, Zinc, Fully Threaded 3

12 72605A Spacer, 1/8” Schedule 80 PVC, 3.5" Long 4

13 70020B Gasket, Vacuum Motor Seal 2

14 72611A Vacuum Motor, 3-Stage, 230V, 5.7IN 2

15 7BF003 Nut, Kep, #10-24 Zinc 18

16 7CM003 Washer, #10 USS Flat, 18-8 SS 6

17 72624A Cover, Vacuum Manifold, Short 1

18 72641A Gasket, Vac Manifold, Short 1

19 X9069+ End Loop, SS, w/ 2 holes, 16G 1

20 72638A Pressure Regulator Plate 1

21 72173A Spring Clip, Black Vinyl Coated 1

22 72636A Cover Plate, Bottom 1

23 72388A Screw, #10 x 5/8, Tap Phil, SS Pan Head 6

24 PX65+ Caster, 4" Black 2

25 7DT001 Bolt, 5/16-18 x 5/8, Hex Tap Zinc 8

26 72387A Screw, #8 x 5/8, Black, Tap Phil, Pan Head 8

27 72661A Wand Holder 1

28 72662A Screw, #10 , Phil Flat SM, Black, Undercut Head 3

29 PX6+ 1/4 x 1/4 Female Quick Disconnect, Brass 1

30 7CX002 Nipple, Hex 1/4 MPT 2

31 X8239+ Washer, USS Flat Zinc 1

32 PC38+ Connector, Double Thread, Female, 1/4" to 1/4" Coupling 1

33 72642A Gasket, Vac Manifold, Circle 1

34 72625A Cover, Vacuum Manifold, Circle 1

35 72643A Pump Assembly, 500 PSI 1

36 72639A Gasket, Mounting Pressure Regulator 2

37 71644A Screw,#10 x 1”, Phil Pan, TS, Type A 18-8 SS 1

38 PF1750-2+ Heater Unit, 220V 1

39 72020A Screw, #12 x 1”, Self-Tap, PHMS, Zinc 4

407BS003 Screw,1/4-20 x 1/2, Phil, Pan , MS 18-8 SS 4

41 X9014+ Hinge 2

42 PD8+ Strain Relief, 1/2" NPT 2

43 PX112+ Pigtail, Black, 12/3 SJT x39" Long 1

44 PX112R+ Pigtail, Red, 12/3 SJT x 39" Long 1

45 X9131+ Cord Panel 1

46 X8008N+ Nut, Lock, 1/2" Steel Conduit 2

47 X9177+ Screw, Phil Pan, Ext Tooth Washer, Fully Threaded 2

48 72665A Insert, Tee Nut, ?-20 Thread, ? High, .305 Barrel Diameter 2

49 X8256+ Nut, 8-32 Keps, Zinc 4

50 7BS002 Screw, 8-32 x 1/2 Phil, Pan MS, 18-8 SS 4

51 7GF033 Pad, Motor Mount 2

53 X8848+ Jacknut, 1/4-20, Steel, #8 LJN 4

54 7EW001 Screw, 1/4-20 x 3/4", Phil, Pan, MS SS 4

55 X8235+ Washer, 1/4 Flat, USS, Zinc 4

56 71521A Tee, Barb, 1/2" x 1/2" x 1/2" 1

57 7DL008 Clamp, 1/2" Worm Gear, SS, Hex Slot 5

58 70079C Hose, 1/2" Wire Reinforced 42”

59 X9098+ Screw, #10 x 1”, A point, PH pan head 2

60 X9178+ Foam, Cord Panel 1

61 X8542+ Hose, Solution, 1/4" ID, 400 PSI 70”

62 PC66+ Fitting, Brass, 1/8 NPTM x 1/4 Hose Barb 5

63 71130A Coupler, QD, 1/8 M 2

64 70101A Nipple, QD, 1/8 F, Brass 2

65 72713B Heater coil, 3-Stage Vacuum 1

66 7AT003 Barb, Hose, 1/4 H – ? M 2

67 SW158+ Cable Clamp 2

68 X8244+ Screw, 10-24 x 2”, Phil, Pan MS, Zinc 2

69 7AV001 Tee Union, 1/4 NPT 1

70 72726A Valve, 3-Way 1

71 PX212+ Fitting, Brass, 90° Elbow, 1/4 NPTM x 1/4 Hose Barb 1

72 7DL003 Clamp, Hose, 1/4" 7

10

Troubleshooting Information

ELECTRICAL SYSTEM

PROBLEM POSSIBLE CAUSE SOLUTION

No electrical power. 1. Defective power cord. 1. Replace

2. Circuit breaker off or 2. Turn circuit breaker

fuse blown. on or replace fuse.

Unplug any equipment

using the same circuit.

Switch is turned on. 1. Faulty electrical cable. 1. Repair or replace.

Intermittent power to 2. Defective switches. 2. Replace.

motor(s). 3. Loose terminal or dis- 3. Replace.

colored terminal connections.

Electrical Shock 1. Equipment not 1. Locate grounded

grounded. outlet.

VACUUM SYSTEM

PROBLEM POSSIBLE CAUSE SOLUTION

Vacuum motor on 1. Drain hose open. 1. Close drain hose.

Little or no vacuum Recovery tank lid must

on wand head. be closed.

2. Defective vacuum hose 2. Repair or replace.

hose. Kinks in vacuum

hose.

3. Vacuum disconnected 3. Open machine, connect

vacuum hose to

recovery tank.

Not enough vacuum 1. Damaged recovery 1. Replace

power at the machine. tank lid.

2. Lint clogging ball - 2. Remove screen.

type shutoff screen. Clean out fibers and

accumulated dirt.

3. Vacuum hose connection 3. Check for leaks

between stand pipe and around clamps and cuffs

vacuum motor. (tighten). Replace damaged

hose(s).

4. Vacuum motor 4. Check air flow by

exhaust blocked. removing hose from

machine and feel the

exhaust under the

machine. Remove

obstruction.

5. Cords not plugged into 5. Relocate one cord to a

seperate circuits different room.

V

ACUUM SYSTEM

PROBLEM POSSIBLE CAUSE SOLUTION

Motor running and no 1. Faulty vacuum motor. 1. Replace.

vacuum at all.

No exhaust from the 2. Water shutoff closed. 2. Clean water shutoff

blowport. screen.

Premature closing of 1. Dirty or clogged shut- 1. Remove and clean

ball type shutoff. off filter screen. screen.

Ball type shutoff 2. Ball coated with 2. Remove and rinse

failing to release after detergent or other ball with clean water.

recovery tank is drained. foreign material.

2. Screen slightly out of 3. Bend screen by

round. squeezing slightly by

hand until there is an

obvious space between

ball and inside of screen.

Foam/dirty solution 1. Foam from carpet by- 1. Use additional

coming out of vacuum passing water shutoff. defoamer.

exhaust port. 2. Elbow in vacuum tank 2. The elbow should be

is not positioned pointed directly at the

correctly. side wall of the tank

away from the ball type

shutoff.

SOLUTION SYSTEM

PROBLEM POSSIBLE CAUSE SOLUTION

Pump motor on – 1. Clogged or faulty 1. Check intake on

no spray through jets. solution control valve. valve and remove lint

or other foreign

material.

2. Clogged or faulty 2. Depress plunger on

quick disconnect on solution hose against

housing. inside wall of solution

tank. If solution is flow-

ing at this point, the

system is O.K. If no

solution flows, check the

quick disconnect for lint

and other foreign matter.

3. Punctured pump 3. Replace with

diaphragm. diaphragm repair kit.

4. Clogged jets 4. clean jets on wand or tool.

PROBLEM POSSIBLE CAUSE SOLUTION

Uneven spray from 1. Clogged strainer in 1. Unscrew strainer

jet. Spray weak or solution tank. and remove lint and

uneven. any other foreign

material from screen.

2. Clogged jet. 2. Remove and clean.

Leaking or stuck 1. Foreign material in 1. Remove brass hex

solution valve. valve. plug, clean valve and

replace.

2. Loose brass hex nut. 2. Reseal hex and plug.

3. Valve worn or seals 3. Replace worn parts

worn. with solution valve

repair kit.

Pump motor 1. Loose wiring 1. Tighten wiring

not working. 2. Defective pump 2. Replace with new

pressure switch pressure switch assembly

3. Motor burnout 3. Replace pump motor

Pump pressure low 1. Clogged screens on 1. Unscrew strainer

strainer in solution tank

. remove lint and any

other foreign material

from screen.

2. Punctured pump 2. Replace with

diaphragm. diaphragm repair kit.

3. Defective rectifier or 3. Replace.

motor.

4. Pump not primed 4. Plug priming hose into

solution connection and place

end in solution tank. Run

pump for 4 minutes

Pump pressure varies. 1. Worn carbon brushes. 1. Replace brushes.

2. Defective pump 2. Replace.

pressure control switch.

A Tacony Company

3101 Wichita Court • Ft. Worth, TX 76140-1710

WARRANTY

The manufacturer warrants to the original purchaser that products manufactured are free from defects of

workmanship and material, provided such goods are installed, operated and maintained in accordance with

written manuals or other instructions for a period of 5 years from date of purchase on housings and frame, 3

years on heater, 1 year on pump, vac motor, and parts and workmanship. In case you as our customer, meet

any trouble with your machine, contact your Powr-Flite representative who will be happy to be of service to

you and will take care of the warranty settlement.

NOTE: Alterations and changes made to the machine without written approval of the

manufacturer and use of unapproved spare parts will not be covered by warranty.