DR2500DC Manual Viper Dragon Dr2000dc Floor Buffer Burnisher Parts And Operator

: Sweepscrub Viper-Dragon-Dr2000Dc-Floor-Buffer-Burnisher-Parts-And-Operator-Manual viper-dragon-dr2000dc-floor-buffer-burnisher-parts-and-operator-manual 1297 file product_file

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

www.usviper.com

DRAGON 2000RPM DUST
CONTROL BURNISHER
OWNERS MANUAL

IMPORTANT: READ OWNERS MANUAL CAREFULLY
Please fill out & return your warranty card!

MODEL#

DR2000DC

SERIAL#

VIPER ...exceptional
value

REV.03 (2014- )
VF54042

TABLE OF CONTENTS
Safety Precautions

1

Machine Operation

2-3

Machine Maintenance & Storage
Parts Lists
Wiring Diagram

3
4-9
10

SAFETY PRECAUTIONS
!!! This machine must be grounded!
Grounding provides the path of least
resistance for electrical current. To reduce
the risk of electrical shock should the
machine malfunction, the machine has a
special grounding plug. Do not remove the
ground pin under any circumstances!

This machine is intended for commercial
use. It is constructed for use in an indoor
environment and is not intended for any
other use. Use only recommended
accessories.
All operators shall read, understand and
exercise the following safety precautions:

2) Before operating machine:
- Make sure all safety devices are in
place and operate properly.
3) When using machine:
- Only use approved burnishing pads.
- Do not run machine over cord.
- Do not pull machine by cord or plug.
- Do not pull cord around sharp
edges or corners.
- Ensure the dust collection bag is in
place and is tightly sealed to the
machine.
- Turn power switch to “off “ prior to
unplugging machine.
- Do not unplug by pulling on the cord.
- Do not stretch cord.
- Do not handle plug with wet hands.
- Keep cord away from heated
surfaces.
- Do not pick up burning or smoking
debris such as cigarettes, matches
or hot ashes.
- Report machine damage or faulty
operation immediately.
4) Before leaving or servicing machine:
- Turn off machine.
- Unplug cord from outlet.

1) Do not operate machine:
- Unless trained and authorized.
- Unless you have read and understand
operators manual.
- In flammable or explosive areas.
- With damaged cord or plug.
- If not in proper operating condition.
- In outdoor areas.
- In standing water.
- Without bag / filters in place.
- With the use of extension cords.

5) When servicing machine:
- Unplug cord from outlet.
- Use manufacturer supplied or
approved replacement parts.

1

Operation of High Speed Floor Machine
*THIS IS A SPECIALIZED MACHINE
WHICH REQUIRES THE OPERATOR TO
UTILIZE A VIPER APPROVED PAD, AND
MUST BE ADJUSTED PROPERLY TO
ENSURE THE HIGHEST POSSIBLE
PERFORMANCE AND PRODUCTIVITY.

8] The handle height may be adjusted by
lifting up on the handle release lever,
located on the right side of the
switch housing.
Pull trigger and
lower handle to desired operating
position.
Release trigger to lock
handle into place.

*Read operators manual thoroughly prior
to operating or servicing this machine.

9] To start the machine, push on the red
safety release button located on the
top of the switch housing and
squeeze either switch lever.

GENERAL USE
1] Remove any obstructions or other
obstacles in the area which is to be
cleaned.
2] Remove dust recovery bag and empty it
out in a trash receptacle. Replace
dust recovery bag on machine, ensuring
it is sealed tightly to the machine.
3] Place handle in upright position and tilt
machine back until handle rests on the
floor.
*Be sure the machine is not plugged into
an outlet.
4] Remove the pad center gripping device
by unscrewing the thumbscrews.
5) Place a "Viper approved" burnishing pad
on the pad driver and re-attach the
center gripping device. (check with your
Viper distributor for approved pads)
6] Place machine back into its upright
position.
7] Plug power cord into grounded outlet.

10) Once the machine has reached
operating speed, look at the digital pad
pressure meter located on the top of
the motor cover. There are 3 light
colors which will help you determine
optimal pad pressure for operating the
machine. RED LIGHT(S): If one or both
red lights are illuminated, stop the
machine and turn the pad pressure

*Do not use an extension cord in
conjunction with the standard power
cord.

2

adjustment knob to the right to reduce
pad pressure. YELLOW LIGHT(S): If one
or both yellow lights is illuminated, stop
the machine and turn the pad pressure
adjustment knob to the left to increase
the amount of pad pressure. GREEN
LIGHT(S): If one, two or three green
lights are illuminated, the machine is
running at the optimal pad pressure
and you may begin working.

6] Check machine for loose or missing nuts
and bolts, and replace as necessary.
7] If the machine is used in a dusty
environment, you may remove the
motor cover and blow the motor clean
with compressed air. This will allow for
good ventilation and help the motor run
cooler.

11] When the machine is in operation,
both hands should be gripping on the
handle.
12] To stop the machine at any time,
simply release the switch lever, and the
machine will stop automatically.

STORAGE

MAINTENANCE

1] Unplug machine from power source.
2] Store in upright position in a dry area.

To keep the machine performing well for
many years, please follow the following
maintenance procedures.

*Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1] Unplug machine as soon as you are done
using it.
2) Remove dust recovery bag and empty
contents into a trash receptacle.
Inspect dust recovery bag for any
damage prior to replacing it on the
machine.
3] Clean the outside of the machine with a
mild cleaner.
4] Check power cord for any damage. If
any damage is detected, replace the
cord immediately.
5] Lubricate wheels with a water resistant
lubricant every month.

3

PARTS LIST
BASE GROUP FOR DR2000DC

4

PARTS LIST
DIA
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38

PART
NUMBER
VF52114
VF52115
VF54048
VV20509
VF54017
VF54047
VF13503
VF13524
VF54020
VF54019
GT13016
VA13480
VF13519
VF54009
VF14007
VF54010
VF14078
ZW42540A
VF54046
VF54004
VF50119
VF52017
VF13666
VF44012
VF54005
VV13621
VA13474
VF13474A
VF54015
VA14010
VF54016
VF13517
VF13518
GT13097
VF52008
VF99024
VF52021
GT13018

DESCRIPTION
PLASTIC STAND, RIGHT
PLASTIC STAND, LEFT
CONNECTOR, MOTOR COVER
SCREW, M5x10, PH
LABEL
COVER, MOTOR
NUT, NYLON INSERT, M8
WASHER, PLAIN
RIGHT ARM
LEFT ARM
SCREW, M8x60, HEX SOCKET
SCREW, M8x40, HEX SOCKET
WASHER, LOCK,φ8
BUSHING
HEX SCREW, M10x32
ADJUSTMENT SCREW
SCREW, M3x10, PH
LED DISPLAY PANEL
RISING SCREW
WHEEL BRACKET
WAVE WASHER, φ12
WHEEL, 5"
WASHER, PLAIN, φ12
SCREW, M5x12.7
RETAINER PLATE, AXLE
SCREW, ST5x20
SCREW, M5x16, PH
WASHER, PLAIN, φ5xφ16
BUMPER
SCREW, M5x20, PH
CLAMP, SKIRT
WASHER, PLAIN, φ10
WASHER, LOCK, φ10
HEX SCREW, 3/8"-16x1.25"
SPACER
PAD HOLDER, 20"
WASHER, PLAIN
HEX SCREW, M8x30

5

NO
REQ'D
1
1
1
16
2
1
3
3
1
1
3
4
5
2
2
1
4
1
4
1
4
4
4
4
2
6
2
4
1
2
1
6
6
4
1
1
1
1

PARTS LIST
DIA
NO
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65

PART
NUMBER
VF54027
VF99003A
VF54006
VF54011
VF54028
VF54001A
VF54025
VF54036
VF50108
VF14081
VF50103A
VF54021
ZD40205
VF54007
VF13022
VF54003
ZD40B
VF52022
VF44204
VF52023
VF54040
GT13032
VF14232
VF54008
VF54014
VF13544
VF47035A

DESCRIPTION
LOCK WASHER, BIG MOUTH
BIG MOUTH
FLEXIBLE SKIRT
CASTER, DUAL SWIVEL
SCREW BUSHING, HOUSING
HOUSING
ADJUSTMENT DECAL
HOOK, COVER, DUST BAG
NUT
NUT, M12
ADJUSTING KNOB, CASTER
SPACER
KEY, MOTOR SHAFT
ELBOW ADAPTOR
SCREW, M4x12, PH
DUST COLLECTOR BAG
MOTOR, 120V
THERMAL CONDUCTION GASKET
RECTIFIER
COVER, RECTIFIER
RISER, ARM
WASHER, PLAIN, φ6xφ16
HEX SCREW, M6x10
PIVOT BLOCK, ADJUSTOR
COVER, DUST BAG
SCREW, ST4x10
"VIPER" LOGO

6

NO
REQ'D
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
1
1
4
1

7

PARTS LIST
DIA
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38

PART
NUMBER
VF47009
VF54037
VF47028
GV40227
GV40228
VF50120A
VF47015
VF14080
VF14000
VF47046
VF47045A
VF13616
GT13019
VF47052
GT13013
VF47103
VF47007
VF47033
VF47008
VF47102
VA13474
VA13476
VF45119
VF54043
VF14212
VF13511
VF44203
VF45124A
VV13650
VF48309
VF46703
AS22009
VF52107
VF14226
VF52118
VF54029
VF14218
VF46705

DESCRIPTION
FRONT COVER, GEAR SEAT
GEAR SEAT
GEAR & LEVELING INSERT KIT
WASHER, NYLON
"O" RING, GEAR SEAT
GROMMET
REAR COVER, GEAR SEAT
SELF-TAPPING SCREW, ST4x25
SELF-TAPPING SCREW, ST4x35
SEAL RING
HOOK, CABLE
SCREW, HEX SOCKET, M10x55
HEX SCREW, M6x40
GEAR & LEVELING INSERT KIT
NUT, M4
LEVELING ROD
SPRING, LEVELING
RETAINER
SEAL, TUBE
TUBE
SCREW, M5x16, PH
SCREW, M5x40, PH
CORD, POWER SUPPLY, STOW 14/3C
SERIAL TAG
SCREW, M3x25, PH
WASHER, LOCK, INTERNAL TOOTH
SWITCH ASSY, 20A, 250V
JUMP WIRE
SCREW, M4x10, PH
BLOCK, HANDLE CABLE
OPERATING TRIGGER, LEFT
STRAIN RELIEF, CORD
COVER, SOLUTION LEVER
SCREW, FH, M6X35
REAR COVER, SWITCH HOUSING
DECAL, NOTICE
SCREW, M6x40, PH
SAFETY BLOCK

8

NO
REQ'D
1
1
1
2
2
2
1
2
2
1
1
1
4
1
4
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
2
1
1
2
1

PARTS LIST
DIA
NO
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53

PART
NUMBER
GV40218
VF99010C
VF13527
VF13526
VF46704
VF48306
GT13014
VF46707
GT13017
VF46706
VF46701
VF47035A
VF13600
VF13502
VF45120

DESCRIPTION
SPRING, SAFETY BLOCK
CIRCUIT BREAKER, 17A
EXTERNAL TOOTH, WASHER, φ4
SCREW, HOLDING, M4x30
OPERATING TRIGGER, RIGHT
PIN, LEVER
NUT, M4, NYLON INSERT
TRIGGER, HANDLE ADJUSTMENT
BIG WASHER, PLAIN, φ4xφ16
HANDLE GRIP
FRONT COVER, SWITCH HOUSING
"VIPER" LOGO
WASHER, PLAIN, φ6
NUT, NYLON INSERT, M6
CABLE, HANDLE, SJTW 14/3C

9

NO
REQ'D
1
1
1
1
1
3
1
1
1
2
1
1
4
4
1

Green

Green

STOW 14/3C
Power
Supply
Cord

White

Circuit
Breaker

White

Black

Switch

Switch Housing

Handle
Cord

Black

Black

~

~
Red

White

+

LED

Rectifier

PCB

RED

BLACK

Motor

Wiring Diagram
DR2000DC

10



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Jiangzc
Create Date                     : 2007:03:26 10:44:06+08:00
Modify Date                     : 2016:09:28 09:01:57-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29
Creator Tool                    : pdfFactory Pro www.pdffactory.com
Metadata Date                   : 2016:09:28 09:01:57-05:00
Format                          : application/pdf
Creator                         : Jiangzc
Title                           : DR2500DC Manual
Producer                        : pdfFactory Pro 3.10 (Windows XP Professional Chinese)
Document ID                     : uuid:75f6e38b-951a-41f2-83fb-1c801d95b7a9
Instance ID                     : uuid:05f9c492-7c75-41c2-ad1a-99479154f56a
Page Count                      : 12

EXIF Metadata provided by EXIF.tools