D Viper Venom Vn20ds Dual Speed Hd Floor Buffer Parts And Operator Manual

: Sweepscrub Viper-Venom-Vn20Ds-Dual-Speed-Hd-Floor-Buffer-Parts-And-Operator-Manual viper-venom-vn20ds-dual-speed-hd-floor-buffer-parts-and-operator-manual 1285 file product_file

Open the PDF directly: View PDF .
Page Count: 9

Download
Open PDF In Browser	View PDF

VIP

ER

VIPER

REV.03 (2014-09)
VF41053MA

TABLE OF CONTENTS
Safety Precautions

3

Machine Operation

4

Machine Maintenance & Storage

4

Parts List

5---8

Wiring Diagram

9

2

SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS

-

General –This floor – finishing machine shall be
grounded while in use to protect the operator
from electric shock. The machine is provided
with a three –conductor cord and a three contact
grounding type attachment plug to fit the proper
grounding type receptacle. The green [or green
and yellow] conductor in the cord is the
grounding wire. Never connect this wire to other
than the grounding pin of the attachment plug.

-

Unless trained and authorized.
Unless you have read and understand
operators manual.
In flammable or explosive areas.
With a damaged cord or plug.
If not in proper operating condition.
In outdoor areas.
In standing water.
With the use of extension cords.

2] Before operating machine:
- Make sure all safety devices are in place
and operate properly.

This machine is for use on a nominal 120-Volt
circuit and has a grounding plug that resembles
the plug illustrated in figure below. Make sure
that the machine is connected to an outlet
having the same configuration as the plug. No
adapter should be used with this machine.

3] When using machine:
- Do not run machine over cord.
- Do not pull machine by cord or plug.
- Do not pull cord around sharp edges of
corners.
- Do not unplug by pulling on the cord.
- Do not stretch cord.
- Do not handle plug with wet hands.
- Keep cord away from heated surfaces.
- Report machine damage of faulty
operation immediately.
4] Before leaving or servicing machine:
- Turn off machine.
- Unplug cord from outlet.
5] When servicing machine:
- Unplug cord from outlet.
- Use manufacturer supplied or approved
replacements parts.
-

This machine is intended for Commercial use. It
is constructed for use in an indoor environment
and is not intended for any other use. Use only
recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:

1] Do not operate machine:

3

Operation of Floor Machines
10.
During operation, to make the
machine go right, gently raise the
handle. To make the machine go left,
gently lower the handle.
11.
To stop the machine at any time,
simply release the operating trigger(s)
and the machine will stop automatically.

* READ OPERATORS MANUAL
THOROUGHLY PRIOR TO OPERATING OR
SERVICING THIS MACHINE.

GENERAL USE
1. Remove any obstructions or other
obstacles in the area which is to be
cleaned.
2. Place the handle in the upright position
and tilt machine back until handle rests
on the floor
* Be sure the machine is not plugged into
an outlet
3. Attach the pad driver or brush to the
machine by placing the clutch plate over
the gearbox hub and turning the driver
/ brush ¼ turn.
4. Place machine back into its upright
position.
5. Plug power cord into a grounded outlet.
* Never use an extension cord in
conjunction with the standard power cord.
6. The handle height may be adjusted by
lifting up the compression handle which
is located on the right side of the handle
tube about 1 foot above floor level.
Release the compression handle and
adjust handle to safe operating height,
then push back down on the
compression handle to lock the handle in
operating position.
7. Select either low speed (185rpm) or
high speed (330rpm) by pushing the
motor mounted switch into the low or
high position.
* Never change the speed while operating
the machine. Be sure the power is turned
off prior to changing the speed.
8. To start the machine, press the red
safety button on the top of the upper
switch housing, and then squeeze either
of the operating triggers. (the safety
button must be depressed prior to
squeezing the operating triggers.)
9. When the machine is in operation, both
hands should be placed on the switch
housing (upper handle).

MAINTENANCE
To keep the machine performing well for
many years, please follow the following
maintenance procedures.
* Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1. Unplug machine as soon as you are
done using it.
2. Tilt machine back and remove pad driver
or brush.
* Never store a low speed machine with
the pad driver or brush mounted to the
machine.
3. Clean the outside of the machine with a
mild cleaner.
4. Check power cord for any damage. If
damage is detected, replace power cord
immediately.
5. Lubricate wheels with a water resistant
lubricant once a month.
6. Check machine for loose or missing nuts
and bolts, and replace as necessary.
7. If the machine is used in a dusty
environment, you may remove the motor
cover and blow the motor clean with
compressed air. This will ensure proper
ventilation, and allow the motor to run
cooler.

STORAGE
1. Unplug machine from power source and
wrap cord on handle.
2. Tilt machine back and remove pad driver
or brush.
3. Store machine in upright position and in
a dry area.

4

5

HANDLE GROUP FOR VN20DS
DIA
NO

PART
NUMBER

DESCRIPTION

NO
REQ'D

1

VF30016

HANDLE RELEASE

1

2

VF30017

SCREW

1

3

VF30018

WASHER,PLAIN

2

4

VF300152

BOLT,HANDLE RELEASE

1

5

VF45125

CORD,HANDLE

1

6

AS41901

PLUG PROTECTOR SMALL MALE

1

7

VF50120A

GROMMET

1

8

VF13504

NUT,LOCK,M10

1

9

VF30027

WASHER,PLAIN

1

10

VF300141

CORD WRAP BLOCK

1

11

VF13493

SCREW,M6X10

1

12

AS112205A

TUBE

1

13

VF13570

14

VF13604

WASHER,TEETH,M5

4

15

VF40169

CONNECTION PLATE

1

16

VF44018

LEVER,SOLUTION

1

17

VV13661

SCREW,M4X12

2

18

VF48306

PIN

3

19

VF44016

LEVER,LEFT,SWITCH

1

20

VF45119

CORD,POWER SUPPLY

1

21

AS22009

STRAIN RELIEF,CORD

1

22

VF30108

GASKET,HANDLE,SOLUTION

1

23

VF14223

SCREW,M6X25

2

24

VF14218

SCREW,M6X45

2

25

VF13528

TEETH WASHER,M6

2

26

VF30102

REAR COVER

1

27

VF99010C

BREAKER,CIRCUIT

1

28

VF30109

COVER

1

29

GT13013

NUT,M4

3

30

VF48309

CLAMP BLOCK

1

31

VF44017

LEVER,RIGHT,SWITCH

1

32

VF44203

SWITCH ASSY

1

33

VF14212

SCREW M3X25

2

34

VF13527

WASHER,TEETH,M4

1

35

VF13526

SCREW,M4X30

1

36

VF46705

SAFETY BOTTON

1

37

GV40218

SPRING,SAFETY BUTTON

1

38

VF48310

HANDLE GRIP

2

39

VF30101

FRONT COVER

1

40
41

VF47035A
VF14222

LOGO
,
SCREW,M5X12

1
4

PIN

6

1

7

BASE GROUP FOR VN20DS
DIA
NO

PART
NUMBER

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53

GT13080
VF30011
VF30026
VF30020
VV20274
GV40235
VV13621
VF13474A
VF13613
VA13474
VF13524
VF13519
VF13618
MF-VF002-4A
MF-VF002-2
MF-VF022
VF30004
ZD48315
ZD48200
VF30006
VF99926-2
VF30008
VF40152
VF30019
VF13520
VF50119
VF48202
VF13666
VF44012
ZD40225
VF999802B
VF99021
MT01102
VF40990
VF41079
ZD48310
ZD48000
VA13473
VF44204
VA91347
ZD48309DY
VF13604
VF14214
GT13014
ZD48316A
GT13048
VV67405
VV67405-1A
AS41902
VF999794
ZD48330
VF40994
VF40997

SCREW, M6 X 30
CLAMP BLOCK, HANDLE
AXLE
BRACKET, LEFT HANDLE
WASHER, PLAIN, M13
CLAMP BLOCK, AXLE
SCREW, SELF-TAPPING, ST, M5 X 20
WASHER PLAIN,
WASHER,
PLAIN M5
SCREW, M5 X 20
SCREW, M5 X 16
WASHER, PLAIN, M8
WASHER, LOCK, M8
SCREW, 5/16" - 2 1/4"
SCREW, SELF-TAPPING, 1/4"-1"
CLUTCH PLATE
PAD HOLDER, 19"
BUMPER, 20"
BEARING, #6002Z
SHAFT & ROTOR ASSEMBLY
FRAME, 20"
KIT, CARBON BRUSH
ALUMINIUM BASE, MOTOR
HOSE BARB
BRACKET, HANDLE, RIGHT
WASHER, LOCK
WASHER, LOCK, M12
WHEEL, 5"
WASHER, M6
SCREW, M6 X 12.7
BEARING, #6203Z
GEAR BOX
COULPING
SLEEVE
LABEL, DUAL SPEED
LABEL, VIPER
LABEL, MOTOR
MOTOR, DUAL SPEED
SCREW, M4 X 16
RECTIFIER
SWITCH
SHELL
WASHER, TOOTH, M5
SCREW, M5 X 8
NUT, NYLON INSERT, M4
TRIAC ASSEMBLY
SCREW,
SCREW M4 X 12
STRAIN RELIEF, CORD
NUT
PLUG PROTECTOR, LARGE, FEMALE
CORD, MOTOR
KIT, SPEED ADJUSTMENT
READ MANUAL LABEL
SERIAL TAG

8

NO
REQ'D
4
1
1
1
4
2
4
4
2
5
4
4
4
6
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1

9



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Modify Date                     : 2016:03:29 11:52:25-05:00
Create Date                     : 2010:03:15 11:23:21+08:00
Metadata Date                   : 2016:03:29 11:52:25-05:00
Creator Tool                    : Adobe Acrobat 8.0 Combine Files
Format                          : application/pdf
Title                           : D:\breakdown\USVIPER\TOTAL P1 Model (1)
Creator                         : Administrator
Document ID                     : uuid:1f14ca3a-6033-4a38-8240-db5121a0db2a
Instance ID                     : uuid:a51386d0-a9d5-4d37-a702-d31e684462b6
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Page Count                      : 9
Author                          : Administrator

EXIF Metadata provided by EXIF.tools