Symbol Technologies 6844 Hand-Held PC w/ RF Link User Manual 3264401B

Symbol Technologies Inc Hand-Held PC w/ RF Link 3264401B

manual

68XX Series+-=Status-
68XX Series 1998 - 1999 SYMBOL TECHNOLOGIES, INC. All rights reserved.Symbol reserves the right to make changes to any product to improve reliability, function, or design.Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products.Symbol, Spectrum One, and Spectrum24 are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.Symbol Technologies, Inc.One Symbol PlazaHoltsville, N.Y. 11742-1300http://www.symbol.comPatentsThis product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No.4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,850,078; D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250.Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan).European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713.rev. 1/99
1Quick ReferenceIntroduction The 68XX is a ruggedized, weather-resistant, hand-held portable computer combining the following capability in one package:• PC-standard architecture (8088 16-bit architecture)• DR-DOS compatibility• 16-line by 21-character display• Key input from 46-key alphanumeric keyboard• Integrated scanning capability• Sealed NiCd rechargeable or replaceable alkaline battery pack• Batch communications or RF network communications (with internally mounted antenna):- Spectrum One® RF network (681X)- Spectrum24® RF network (684X).About This GuideThis guide provides the operator with instructions for the following procedures:• Installing/removing the battery• Charging the battery• Powering the 68XX on and off• Adjusting the display contrast• Turning the backlight on/off• Using the keyboard• Using the integrated scanner• Running communications• Troubleshooting the 68XX.
268XX SeriesParts of the 68XX+-=Status-DisplayKeyboardScan LEDStatus LEDScan WindowPWR KeyScan TriggerBattery Lock HandstrapCharging ContactsOpticalConnectorsBatteryCompartmentBatteryReleaseBatteryPack
3Quick ReferenceRequired AccessoriesRequired 68XX accessories include:• Five-cell, 780 mAh NiCd rechargeable battery pack orSix-cell, 600 mAh IS NiCd rechargeable battery pack• CCM 38/6860 4-slot charging and communication module with spare battery charging slotor• CRD 38/6865 1-slot cradle charging and communications cradleor• CRD 38/6866 4-slot charging and communications cradle• RS-232 serial cable(s)• Power supply (1 per cradle).Optional AccessoriesOptional 68XX accessories include:• Wall mounting kit (p/n 3866-000)• UBC battery charger (1000 or 2000)• PC adapter and printer interface module (PIM)• 10-hour trickle battery charger (wall cube)• Spectrum One and Spectrum24 network accessories•Holster.
468XX SeriesProviding PowerPower for the 68XX is provided by a Nickel Cadmium (NiCd) rechargeable battery pack. Note: The Series 3800 NiCd battery packs, 3872-103, 3872-105, and 3872-115, CANNOT be used in the 68XX.Installing New or Recharged NiCd BatteriesTo install the NiCd battery:1. Orient the battery pack with the handle facing the 6800’s scan window. 2. Slide the pack into the battery compartment with the battery release buttons pressed in.3. Press the battery lock in to secure.Changing the Battery Pack for the Intrinsically Safe PDT 68xx terminal To insert the battery pack:1. Firmly insert the battery into the bottom of the terminal as shown in the following illustration. BatteryHandleBatteryLockReleaseButtonBatteryCompartmentScan Window
5Quick Reference2. Use the enclosed battery locking key to lock the battery into place. As you are turning the locking key, the battery locking mechanism should be turning and locking the battery into place. 3. To unlock and remove the battery, use the battery locking key to unlock the battery locking mechanism, and pull the battery out of from the bottom of the terminal. Removing the NiCd Battery Pack1. Press the battery release buttons on both sides of the handle.2. Slide the battery pack out of the handle. Battery Locking KeyBatteryLockingMechanismPress releasebutton Press releasebutton
668XX SeriesCharging the NiCd BatteryTo charge the NiCd battery in the 68XX, use one of the cradles listed in Required Accessories on page 3.Caution: Use only Symbol battery 21-32801-01, 21-325217-01, or 21-35241-01 in this terminal.Note: The 68XX has a built-in safeguard to ensure that an alkaline battery is not recharged when the 68XX is placed in a cradle.1. Seat the 68XX in the cradle against the charging contacts. 2. The 68XX’s Status LED lights solid green when the unit is placed in the cradle. The cradle’s CHARGING LED flashes when charging a discharged battery and remains steady when trickle-charging a charged battery. Refer to the Quick Refer-ence Guide for your cradle for more information.3. Leave the 68XX in the cradle up to 7 hours to recharge a fully discharged battery. The 38/6860 and 38/6865 cradles provide slots for charging spare battery packs outside the 68XX. To charge a spare NiCd battery in a cradle, insert the battery pack in the spare battery slot. The LED indicator lamp under the slot where the pack is placed lights to indicate the battery is charging. A blinking LED indicates 6865 68666860
7Quick Referencea fast charge; a solid LED means slow charge/ready. Spare battery packs are recharged in 7 hours. To charge the NiCd battery in a UBC charger:1. Remove battery pack from 68XX as described in Removing the NiCd Battery Pack on page 5.2. Insert the pack in a UBC adapter.3. Insert the adapter in the UBC charger. Refer to the charger’s documentation for more information.6860CCMSpare BatteryCharging LED Spare BatteryCharging Slots
868XX SeriesOperating the 68XXPowering the 68XX On/OffPower the 68XX on by:• squeezing the scan trigger,• or pressing the PWR key.Note: The battery must be installed, or the 68XX must be in a cradle to power the terminal on.To suspend the 68XX’s operation, press the PWR key. Adjusting the ContrastThe 68XX’s display contrast can be set to 8 levels. To adjust the contrast:• Press FUNC then X to increase the contrast• Press FUNC then Y to decrease the contrast.Tu r n i n g B a c k l i g h t O n / O f fThe 68XX has a backlight to illuminate the display for operating in dim light. To turn the backlight on or off, press FUNC then L (Lamp).The backlight turns off automatically in approximately 15 seconds or when the 68XX is powered off.
9Quick ReferenceUsing the KeyboardThe 68XX uses a 46-key alphanumeric keyboard that produces the 26-character alphabet (A-Z), numbers (0-9), and assorted characters (+, -, X, ÷, =, •). The keypad is color-coded to indicate which modifier key to press to produce a particular character or action.• The Alpha keys marked in white produce the upper-case characters A to Z.• The default numeric keypad produces the numbers 0-9.• Press FUNC and the corresponding numeric key to produce function keys F1 to F10. • Press the cursor keys to scroll up and down the screen.• Press FUNC, then to scroll left and FUNC then to scroll right.• Press BKSP to erase information entered on the display, one character at a time.• Press FUNC then BKSP (SPACE) to enter a blank space.• Press CLR to partially or completely escape from an applica-tion level or screen. CLR also erases all entered data from the screen.•Press SHF to access the shifted keyboard.•CTL performs the control function and is under application control.•Press ENTER to place entered data into the 68XX’s memory.
1068XX Series68XX Series Keyboard=
11Quick ReferenceUsing the Integrated Laser ScannerTo scan:1. Press the scanner trigger to power the 68XX and scanner on. The Scan LED turns red if scanning is enabled and the laser is on.2. Point the 68XX at the bar code and press the trigger.3. Ensure that the scan beam crosses all bars and spaces on the bar code symbol, as shown below:Hold the scanner farther away for larger symbols, and closer for symbols with bars that are close together.Long-range versions support a two-level scan trigger. The first, narrow beam is for aiming, and the second beam decodes the label.4. The LED turns from red to green for successful decodes. The 68XX may also beep.Right Wrong
1268XX SeriesAiming: Hold at an AngleDo not hold the 6800’s scan window directly over the bar code. Laser light reflecting directly back into the scan window from the bar code is known as specular reflection. This strong light can “blind” the scanner and make decoding difficult. The area where specular reflection occurs is known as a “dead zone”.You can tilt the 6800 up to 55° forward or back and achieve a successful decode. Practice quickly shows what tolerances to work within.
13Quick ReferenceRunning CommunicationsCommunicating with a Host The 68XX communicates with a host through the CCM 38/6860, CRD 38/6865, CRD 38/6866, or PC Adapter. For information on setting up the CCM, cradles, or PC Adapter, refer to the 68XX Product Reference Guide or the Quick Reference Guide provided with each unit. To communicate with a host: 1. Set up the cradle(s) or PC Adapter as described in 68XX Product Reference Guide or QRG for the device.2. Place the 6800’s base in the cradle. Press the top of the 68XX against the cradle back until it is firmly seated.The Status LED lights solid green when the 68XX is securely placed in the cradle.3. Start the communications program on the host and the 68XX.Caution: Do NOT remove the 68XX while the cradle’s red COMM LED is blinking.
1468XX SeriesCommunicating with a PrinterThe 68XX communicates with a printer through the printer interface module (PIM). To connect the 68XX to the printer:1. Attach the PIM’s optical connector to the 68XX’s port by in-serting the clips on the connector in the slots on either side of the port.2. Plug the PIM’s DB-9 connector in the printer’s port. 3. Power the printer and 68XX on. Communicating in a RF NetworkThe PDT 6810 operates in a Symbol Spectrum One RF network; the PDT 684X operates in a Symbol Spectrum24 RF network. The Status LED indicates the state of the terminal’s connection to the RF network:Refer to the documentation for the Spectrum One or Spectrum24 network for more information on operating the PDT 68XX in that RF environment. Off indicates that the radio is working and associated with an access point (Spectrum24) or base station (Spectrum One).Status LED indication of RF operation presently not available.Flashes red once per secondto indicate that the radio is out of range or not associated with an access point or base station.Status LED indication of RF operation presently not available.PIMOptical Connector Clips68XX’s Optical PortSlots
15Quick ReferenceTroubleshootingSymptom Possible Cause Action68XX does not power on.Battery is not installed. Verify that the 68XX has power from a NiCd or alkaline battery.NiCd battery not charged. Charge the battery in the terminal, or remove the battery and charge in the spare battery charging slot on the CCM 38/6860 or CRD 38/6866. Alkaline battery is drained. Replace battery.Low Battery messageThe main battery pack is running low. Place the 68XX in a cra-dle and recharge the NiCd battery.OR Power the 68XX off and replace the battery.Battery is dead Battery not replaced after receiving Low Battery message. Replace the battery. Cannot see charac-ters on display.68XX not powered on. Press the PWR key. Battery pack is missing or dead. Replace or recharge the battery pack. Contrast not adjusted properly. Refer to page 8 for the key sequence. Scanner does not decode a bar codeThe bar code is unreadable. Verify that the bar code is not defective, e.g., smudged or dirty.
1668XX SeriesScanner does not decode a bar code(cont’d)Scan window is dirty. Clean scan window with lens tissues for use with eyeglasses. Do NOT use tissues with lotion.Double Key error messageTwo or more keys were pressed at the same time. Press keys in sequence. 68XX does not re-spond when keys are pressedApplication was not successfully download-ed.Ask System Administra-tor to repeat application download.Symptom Possible Cause Action
17Quick ReferenceRegulatory InformationRadio Frequency Interference RequirementsThis device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Radio Frequency Interference Requirements - CanadaThis Class A digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numérique de la Classe A respecte toutes les exigences du Reglement sur le Materiél Brouilleur du Canada.CE Marking and European Union ComplianceProducts intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included:Applicable Directives• Electromagnetic Compatibility Directive 89/336/EEC• Low Voltage Directive 73/23/EECApplicable Standards• EN 55 022 - Limits and Methods of Measurement of Radio Interference Charac-teristics of Information technology Equipment• EN 50 082-1:1997 - Electromagnetic Compatibility - Generic Immunity Stan-dard, Part 1: Residential, commercial, Light Industry
1868XX Series• IEC 1000-4-2(1995-01) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 2: Electrostatic discharge immunity test.• IEC 1000-4-3(1995-03) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 3: Radiated, radio-frequency, electromag-netic field immunity test.• IEC 1000-4-4(1995-01) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 4: Electrical fast transient/burst immunity test.• EN 60 950 + Amd 1 + Amd 2 - Safety of Information Technology Equipment Including Electrical Business Equipment• EN 60 825-1 (EN 60 825) - Safety of Devices Containing Lasers Laser DevicesSymbol products using lasers comply with US 21CFR1040.10, Subchapter J and IEC825/EN 60 825 (or IEC825-1/EN 60 825-1, depending on the date of manufacture). The laser classification is marked on one of the labels on the product.Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.
19Quick ReferenceScanner Labelingw/Symbol battery 21-32810-01See Manual 70-32644-01 for AccessoriesSYMBOL TECHNOLOGIES, INC.BOHEMIA, NY 11716 MADE IN U.S.A. APPROVEDLASERBARCODESCANNER9897LASER LIGHT - DO NOT STARE INTO BEAM630-680nm LASER 1.0 mW MAX OUTPUTCLASS II LASER PRODUCTE143267LISTEDACCESSORYI.T.E.CLUUSCAUTIONVDEACHTUNG LASERSTRAHL. LASERCLASSE 2. NICHT IN DEN STRAHLBLICKEN. LUMIERE LASER-NE PAS REGARDER DANS LE FAISCEAUAPPAREIL A LASER DE CLASSE 2. CAUTION LASER LIGHT. DO NOTSTARE INTO BEAM. CLASS 2 LASER PRODUCT 630-680nW, 1mW LASER‘Nonincendive CL I, Div 2, Gps ABCDSuitable for CL I I, Div 2, Gps FGClass III. Div 1,2FM T4A
2068XX SeriesIn accordance with Clause 5, IEC 0825 and EN60825, the following information is provided to the user:ENGLISHCLASS 1 CLASS 1 LASER PRODUCTCLASS 2 LASER LIGHTDO NOT STARE INTO BEAMCLASS 2 LASER PRODUCTDANISHKLASSE 1 KLASSE 1 LASERPRODUKTKLASSE 2 LASERLYFSE IKKE IND I STRÅLENKLASSE 2 LASERPRODUKTDUTCHKLASSE 1 KLASSE-1 LASERPRODUKTKLASSE 2 LASERLICHTNIET IN STRAAL STARENKLASSE-2 LASERPRODUKTFINNISHLUOKKA 1 LUOKKA 1 LASERTUOTELUOKKA 2 LASERVALOÄLÄ TUIJOTA SÄDETTÄLUOKKA 2 LASERTUOTEFRENCHCLASSE 1 PRODUIT LASER DE CLASSE 1CLASSE 2 LUMIERE LASERNE PAS REGARDER LE RAYON FIXEMENTPRODUIT LASER DE CLASSE 2GERMANKLASSE 1 LASERPRODUKT DER KLASSE 1KLASSE 2 LASERSTRAHLENNICHT DIREKT IN DEN LASERSTRAHL SCHAUENLASERPRODUKT DER KLASSE 2
21Quick ReferenceHEBREWITALIANCLASSE 1 PRODOTTO AL LASER DI CLASSE 1CLASSE 2 LUCE LASERNON FISSARE IL RAGGIOPRODOTTO AL LASER DI CLASSE 2NORWEGIANKLASSE 1 LASERPRODUKT, KLASSE 1KLASSE 2 LASERLYS IKKE STIRR INN I LYSSTRÅLENLASERPRODUKT, KLASSE 2PORTUGUESECLASSE 1 PRODUTO LASER DA CLASSE 1CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO LUMINOSOPRODUTO LASER DA CLASSE 2SPANISHCLASE 1 PRODUCTO LASER DE LA CLASE 1CLASE 2 LUZ LASERNO MIRE FIJAMENTE EL HAZPRODUCTO LASER DE LA CLASE 2SWEDISHKLASS 1 LASERPRODUKT KLASS 1KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLENLASERPRODUKT KLASS 2RF DevicesSymbol’s RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and will be labeled as required. The majority of Symbol’s RF devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any changes or modifications to Symbol Technologies equipment not expressly approved by Symbol Technologies could void the user’s authority to operate the equipment.Service InformationBefore you use a terminal, it must be configured to operate in your facility’s network and run your applications.If you have a problem with running your terminal or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center:United States 1-800-653-5350 Canada 905-629-7226United Kingdom 0800 328 2424 Asia/Pacific 337-6588 Australia 1-800-672-906 Austria 1-505-5794Denmark 7020-1718 Finland 9 5407 580France 01-40-96-52-21 Germany 6074-49020Italy 2-484441 Mexico 5-520-1835Netherlands 315-271700 Norway 66810600
70-32644-01Revision B — February 1999Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300WarrantySymbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmanship. This warranty is provided to the original owner only and is not transferable to any third party. It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii) which has not been maintained in accordance with any operating or handling instructions supplied by Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse, abuse, power shortage, negligence or accident or (iv) which has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of customer and is not covered under this warranty. Wear items and accessories having a Symbol serial number, will carry a 90-day limited warranty. Non-serialized items will carry a 30-day limited warranty.Warranty Coverage and ProcedureDuring the warranty period, Symbol will repair or replace defective products returned to Symbol’s manufacturing plan in the US. For warranty service in North America, call the Symbol Support Center at 1-800-653-5350. International customers should contact the local Symbol office or support center. If warranty service is required, Symbol will issue a Return Material Authorization Number. Products must be shipped in the original or comparable packaging, shipping and insurance charges prepaid. Symbol will ship the repaired or replacement product freight and insurance prepaid in North America. Shipments from the US or other locations will be made F.O.B. Symbol’s manufacturing plant. Symbol will use new or refurbished parts at its discretion and will own all parts removed from repaired products. Customer will pay for the replacement product in case it does not return the replaced product to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange. Customer accepts full responsibility for its software and data including the appropriate backup thereof. Repair or replacement of a product during warranty will not extend the original warranty term. Symbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or phone support, that can be implemented to meet customer’s special operational requirements and are available at a substantial discount during warranty period. GeneralExcept for the warranties stated above, Symbol disclaims all warranties, express or implied, on products furnished hereunder, including without limitation implied warranties of merchantability and fitness for a particular purpose. The stated express warranties are in lieu of all obligations or liabilities on part of Symbol for damages, including without limitation, special, indirect, or consequential damages arising out of or in connection with the use or performance of the product. Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way exceed the purchase price of said product, except in instances of injury to persons or property. Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential damages, so the proceeding exclusion or limitation may not apply to you. South Africa 11-4405668 Spain 9-1-320-39-09Sweden 84452900Latin America Sales Support 1-800-347-0178 Inside US+1-561-483-1275 Outside USEurope/Mid-East Distributor Operations Contact local distributor or call+44 118 945 7360

Navigation menu