Symbol Technologies MC75A8 EDA (Enterprise Digital Assistant) User Manual MC75A User Guide
Symbol Technologies Inc EDA (Enterprise Digital Assistant) MC75A User Guide
Contents
user manual 2 rev
UsingtheMC75A 2-17 ResettingtheMC75A There are two reset functions, warm boot and cold boot. A warm boot restarts the MC75A by closing all running programs. A cold boot also restarts the MC75A, and also resets the clock. Data saved in flash memory or a memory card is not lost. If the MC75A is not functioning properly, perform a warm boot first. If the MC75A still does not respond, perform a cold boot. PerformingaWarmBoot AF Hold down the Power button for approximately five seconds. As soon as the MC75A starts to boot release the Power button. Figure2-16Warm Boot Splash Screen PerformingaColdBoot To perform a cold boot simultaneously press the Power button and the 1 and 9 keys. Figure2-17Cold Boot Splash Screen 2-18 MC75AEnterpriseDigitalAssistantUserGuide WakingtheMC75A The wake-up conditions define what actions wake up the mobile computer after it has gone into suspend mode. The mobile computer can go into suspend mode by either pressing the Power button or automatically by Control Panel time-out settings. These settings are configurable and the factory default settings are shown in are subject to change/update. Table2-6Wake-up Default Settings PowerButton No Mobile computer is inserted into a cradle. No Mobile computer is removed from a cradle. No Mobile computer is connected to a USB device. No Yes AF AC power is applied. AutomaticTime-out ConditionforWake-up Yes Yes Yes Mobile computer is disconnected from a USB device. No Yes A key is pressed. No Yes No Yes No No No No No No Yes Yes Incoming phone call Yes Yes On motion No Yes The scan triggered is pressed. The screen is touched. Audio Jack Audio Btn Bluetooth communication LockingtheMC75A Use the Device Lock feature to prevent use of the device. Note that when locked, the MC75A does not respond to screen or keypad input. To lock the MC75A, tap Start > Lock. The Lock screen appears. To unlock the MC75A, side the Lock button to the left or right. Figure2-18Unlock Device Window UsingtheMC75A 2-19 PasswordLocking AF If the MC75A was locked with a password, a prompt appears for the password. Use the Password window to set a password to disable unauthorized access to the MC75A. NOTE Tap Start > Settings > Lock icon > Password tab. 1. If the device is configured to connect to a network, use a strong (difficult to figure out) password to help protect network security. Password cracking tools continue to improve and the computers used to crack passwords are more powerful than ever. Figure2-19Password Window - Password Tab 2. Select Prompt if device unused for check box to enable password protection. 3. From the drop-down list, select a time value for the protection to take affect after non-use. 4. From the Password type: drop-down list, select either Simple PIN or Strong alphanumeric. 5. For a simple password, enter a four-digit password in the Password field. For a stronger password: a. Enter a seven character password in the Password: field. A strong password must contain at least seven characters and contain at least three of the following: uppercase and lowercase letters, numerals, and punctuation. 2-20 MC75AEnterpriseDigitalAssistantUserGuide b. Re-enter the password in the Confirm: field. 6. Tap OK. 7. To set a hint to remember the password, tap the Hint tab. 8. In the text box, enter a hint for a password reminder. 9. Tap OK. AF When the MC75A is not used for a period of time and the user tries to access the device, the Password window appears. This also appears when the MC75A is connected to a host computer with either a cradle or communication cable. Figure2-20Enter Password Windows Enter the password to un-lock the device. Tap the Unlock button to unlock the device and go to the Today screen, or tap the Contact button to unlock the device and go to the Contacts window or tap the Email button to unlock the device and go to the Messaging window. FunctionButtons NOTE You can make emergency calls even when the MC75A is locked. See for more information. The MC75A’s buttons perform certain functions. UsingtheMC75A 2-21 Power Button Scan/Action Button Action Button Scan/Action Button AF Figure2-21Function Buttons Up/Down Button • Power: Press the red Power button to turn the MC75A screen on and off. The MC75A is in suspend mode when the screen is off. For more information, see Powering On the MC75A on page 1-7. Also use the Power button to reset the MC75A by performing a warm or cold boot. See Resetting the MC75A on page 2-17. • Scan/Action: Press to scan bar codes or capture images. See Chapter 3, Data Capture. Or, press to open an application or perform a function. See the Microsoft® Applications for Mobile 6 User Guide to set an application to open. • Up/Down: Press to increase or decrease the MC75A’s volume. • Action: Press to open an application or perform a function. See the Microsoft® Applications for Mobile 6 User Guide to set an application to open. Stylus Use the MC75A stylus to select items and enter information. The stylus functions as a mouse. • Tap: Touch the screen once with the stylus to press option buttons and open menu items. • Tap and Hold: Tap and hold the stylus on an item to see a list of actions available for that item. On the pop-up menu that appears, tap the action to perform. • Drag: Hold the stylus on the screen and drag across the screen to select text and images. Drag in a list to select multiple items. NOTE Motorola recommends using the spring-loaded tip of the stylus to write on the screen, and the back end of the stylus to tap the screen. Use your finger to press the Power button and keypad buttons. CAUTION To prevent damage to the screen, do not use any device other than the Motorola-provided stylus. 2-22 MC75AEnterpriseDigitalAssistantUserGuide EnteringData AF When entering data on the keypad, use either the single-hand method or the two-hand method as shown in Figure 2-22. Single-hand Method Figure2-22Entering Data on the Keypad Two-hand Method UsingtheMC75A 2-23 InteractiveSensorTechnology This section describes the functionality of the Interactive Sensor Technology (IST) feature on the MC75A. The IST supports the following features. • Power Management – manage power by configuring IST to control switching on/off the backlight, control suspend mode of the MC75A by monitoring motion and orientation. • Display Orientation – switch the screen orientation to either landscape or portrait depending on the MC75A orientation. • Free Fall Detection – monitors free fall duration and records the time and type of the drop event. PowerManagement DisplayOrientation AF The MC75A orientation and motion sensitive data can be used as an indicator of MC75A usage and can be used to manage the battery power of the mobile computer. For example, IST can be configured to control the backlight on and off functionality or go into suspend according to a user gesture by placing screen facing down. It can also be used to keep the MC75A active while it is in movement to prevent it from quickly going into suspend mode while in use. The screen can be rotated between portrait and landscape modes automatically, depending on the physical orientation of the MC75A. For example, if the MC75A is rotated 90° counterclockwise, IST rotates the display counterclockwise 90° so that the screen display appears correct. This functionality is achieved by monitoring screen angle and rotating the display to counter any changes. IST only rotates the screen in multiples of 90°. Figure2-23Display Orientation 2-24 MC75AEnterpriseDigitalAssistantUserGuide FreeFallDetection IST continuously monitors gravitational force on the MC75A according to its current position. When the MC75A free falls, IST detects the absence of gravitational force and records the event data if it detects a free fall more than 450 ms, which may indicates nearly a one meter drop. This data can be used as an indicator of potential abuse or misuse. AF IST features a log for recording the free fall events. This log records the date, time and the time period of the free fall. Figure2-24Free Fall Detection TakingPhotos To take a photo: 1. Tap Start > Pictures & Videos icon. 2. Tap Camera on the command bar. 3. Check the image on the view finder, adjust if necessary. 4. Press the Enter key to take the picture. Hold the MC75A still until the camera flash occurs or the shutter sound is heard. RecordingVideo To record a video clip: UsingtheMC75A 2-25 1. Tap Start > Pictures & Videos icon. 2. Tap Camera on the command bar. 3. Tap Menu > Video to set shooting mode to video. The available recording time displays on the screen. NOTE 4. By default, the time limit for recording videos is set to 30 seconds. Press the Enter key to begin recording. Recording stops when you press the Enter button again. ViewingPhotosandVideos For detailed information on the Photos and Videos, refer to the Microsoft Applications User Guide for Mobile 6, p/n 72E-108299-xx. To view photos and video clips: AF NOTE 1. Tap Start > Pictures & Videos icon. 2. Tap the picture or video clip to view. UsingIrDA NOTE In a Microsoft Windows Mobile program (except Messaging), and Picture & Videos, you can exchange files using either infrared or Bluetooth. You can also beam files (not folders) from the File Explorer window. Tap and hold the item you want to send, then tap Beam File from the pop-up menu. First activate the beam function before exchanging files with another IrDA device. To activate the Beam function: 1. Tap Start > Settings > Connections folder > Beam icon. 2. Tap Receive all incoming beams check box. T 2-26 MC75AEnterpriseDigitalAssistantUserGuide Figure2-25Beam Window Tap OK. InfraredConnection AF 3. Using infrared, you can enable short-range file exchange between your MC75A and another IrDA device. ExchangingFilesusingIRConnection Ensure that the IrDA function on both the MC75A and the other device are enabled. To send files via IrDA connection: Switch to the program where you created the item you want to send and locate the item in the list. NOTE Align the IrDA port of the MC75A with that of the IrDA device so that they are unobstructed and within a close range. 2. Do not cover or block the IrDA window. 1. Figure2-26Align MC75A with IrDA Device 3. Tap and hold the item, then tap Beam [type of item] on the pop-up menu. 4. Tap the device that you want to send the file to. Figure2-27Beam Contact To receive files via IrDA connection: UsingtheMC75A 2-27 Align the IrDA port of the MC75A with that of the other IrDA device so that they are unobstructed and within a close range. 2. On the other device, send the file to the MC75A. AF 1. Figure2-28Receive File 3. When the Receiving Data dialog displays, tap Yes. D AF 2-28 MC75AEnterpriseDigitalAssistantUserGuide Introduction AF Chapter3DataCapture The MC75A offers three types of data capture options: • Laser scanning • Imaging • Color digital camera. LaserScanning To perform data capture a scanning enabled application must be installed on the MC75A. A sample scanning application can be downloaded from the Motorola Support site at http://support.symbol.com. NOTE An MC75A with an integrated laser scanner has the following features: • Reading of a variety of bar code symbologies, including the most popular 1-D code types. • Intuitive aiming for easy point-and-shoot operation. ScanningConsiderations Typically, scanning is a simple matter of aim, scan, and decode and a few quick trial efforts master it. However, consider the following to optimize scanning performance: • Range Any scanning device decodes well over a particular working range — minimum and maximum distances from the bar code. This range varies according to bar code density and scanning device optics. Scanning within range brings quick and dependable decodes; scanning too close or too far away prevents decodes. Move the scanner closer or further away to find the right working range for the bar codes being scanned. • Angle Scanning angle is important for promoting quick decodes. 3-2 MC75AEnterpriseDigitalAssistantUserGuide • Hold the MC75A farther away for larger symbols. • Move the MC75A closer for symbols with bars that are close together. NOTE Scanning procedures depend on the application and MC75A configuration. An application may use different scanning procedures from the one listed above. BarCodeScanning Ensure that a scan enabled application is loaded on the MC75A. Figure3-1Linear Scanning AF 1. Press and hold the scan button. The laser beam exits from the end of the MC75A. Ensure the red scan beam covers the entire bar code. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. 2. Incorrect Correct Figure3-2Linear Scanner Aiming Pattern Release the scan button. 3. Imaging An MC75A with an integrated imager has the following features: • Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types. • The ability to capture and download images to a host for a variety of imaging applications. • Advanced intuitive laser aiming for easy point-and-shoot operation. The imager uses digital camera technology to take a digital picture of a bar code, stores the resulting image in its memory, and executes state-of-the-art software decoding algorithms to extract the data from the image. DataCapture 3-3 OperationalModes MC75A with an integrated imager support three modes of operation, listed below. Activate each mode by pulling the trigger or pressing the Scan button. • Decode Mode: In this mode, the MC75A attempts to locate and decode enabled bar codes within its field of view. The imager remains in this mode as long as you hold the trigger, or until it decodes a bar code. NOTE To enable Pick List Mode, download the Control Panel applet from the web site at http://support.symbol.com. Pick List can also be set in an application using a API command. • Pick List Mode: This mode allows you to selectively decode a bar code when more than one bar code is in the MC75A’s field of view. To accomplish this, move the aiming crosshair over the required bar code to decode only this bar code. This feature is ideal for pick lists containing multiple bar codes and manufacturing or transport labels containing more than one bar code type (either 1D or 2D). • Image Capture Mode: Use this mode to capture an image within the MC75A’s field of view. This is useful for ImagerScanning Ensure that a scan-enabled application is loaded on the MC75A. 1. AF capturing signatures or images of items like damaged boxes. Figure3-3Imager Scanning 2. Press and hold the scan button. The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by the brackets in the aiming pattern. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. Note that when the MC75A is in Pick List Mode, the imager does not decode the bar code until the crosshair touches the bar code. MC75AEnterpriseDigitalAssistantUserGuide AF Figure3-4Imager Aiming Pattern 3-4 Figure3-5Pick List Mode with Multiple Bar Codes 3. Release the scan button. Imager decoding usually occurs instantaneously. The MC75A repeats the steps required to take a digital picture (image) of a poor or difficult bar code as long as the scan button remains pressed. NOTE ColorDigitalCamera MC75A with an integrated color digital camera have the following features: • Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types. • Advanced intuitive aiming for easy point-and-shoot operation. DigitalCameraScanning 1. Ensure that a scan-enabled application is loaded on the MC75A. 2. Aim the camera lens on the back of the MC75A at a bar code. 3. Press and hold the scan button. A preview window appears on the display window with a red aiming reticle in the center. The Scan/Decode LED lights red to indicate that scanning is in process. Figure3-6Sample Scan Application with Preview Window Move the MC75A until the red aiming reticle is on the bar code to scan. The aiming reticle turns green when the MC75A is able to decode the bar code. AF 4. 3-5 DataCapture Figure3-7Digital Camera Scanning Release the scan button. The Scan/Decode LED lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. 5. NOTE The camera decode feature is set by default to automatically decode the bar code when read. This feature can be programmed to display a green aiming reticle upon good decode indicating that the bar code has been successfully decoded and to that the scan button may be released. R AF MC75AEnterpriseDigitalAssistantUserGuide 3-6 T Chapter4UsingthePhone AF Introduction Use the MC75A to make phone calls, set up speed dials, keep track of calls, and send text messages. Your wireless service provider may also provide other services such as voice mail, call forwarding, and caller ID. Also use the integrated phone to connect to an ISP or work network in order to browse the Web and read e-mail. Connect to the Internet or work network over High-Speed Downlink Packet Access (HSDPA) (MC75A6) or Evolution Data-Optimized (EvDO) (MC75A8) using Cellular Line, or using the modem specified by the mobile operator. For more information, or to customize the MC75A phone by changing phone settings, see the MC75A Integrator Guide. AccessingthePhoneKeypad NOTE Keypads vary depending on the carrier, services and the state of the phone. For example, place calls on hold and use Swap to switch active calls on hold. (See Conference Calling on an MC75A6 on page 4-19.) Access the keypad regardless of the program in use. Applications on the MC75A can be in use during a call. Antenna Signal MC75A6 Figure4-1Phone Keypads MC75A8 4-2 MC75AEnterpriseDigitalAssistantUserGuide To access the phone keypad tap Start > Phone or press the green phone key on the MC75A’s keypad. To receive calls when the MC75A is suspended, leave the phone radio turned on and ensure the MC75A is set to wake with any key. TurningthePhoneOnandOff Windows Mobile 6 devices include Wireless Manager, which provides a simple method of enabling and disabling the phone. AF To open Wireless Manager, tap the Connectivity icon. Figure4-2Opening Wireless Manager Select Wireless Manager. The Wireless Manager window appears. To toggle on or off the phone, tap blue Phone bar. To configure settings for a connection, tap Menu > Phone Settings. To receive calls when your device is suspended, leave the phone turned on. NOTE UsingthePhone 4-3 AudioModes The MC75A offers three audio modes for use during phone calls: • Handset Mode: Switches audio to the speaker at the top front of the MC75, so you can use the MC75A as a handset. This is the default mode. • Speaker Mode: Use the MC75A as if on speaker phone. Tap the Speaker On button to activate this mode. Tap the Speaker Off button to switch back to handset mode. • Headset Mode: Connect a wired or Bluetooth headset to automatically switch audio to the headset. While using a Bluetooth headset during a call, the mobile computer will not go into suspend mode. AF NOTE The MC75A defaults to handset mode. When a wired headset is plugged into the MC75A audio connector or a Bluetooth headset is configured for use with the MC75, the earpiece and speakerphone are muted and audio is heard through the headset. Handset Mode Speaker Mode Headset Mode Figure4-3Audio Modes UsingaWiredHeadset You can use a stereo headset for audio communication when using an audio-enabled application. To use a headset, plug the headset jack into the audio connector on the side of the MC75A. Set the MC75A’s volume appropriately before putting the headset on. Plugging a headset into the jack mutes the speaker. For the best audio performance, Motorola recommends a 2.5mm jack headset, see Chapter 7, Accessories. MC75AEnterpriseDigitalAssistantUserGuide 4-4 Figure4-4Using a Headset UsingaBluetoothHeadset AF You can use a Bluetooth headset for audio communication when using an audio-enabled application. See Chapter 6, Using Bluetooth for information on connecting a Bluetooth headset to the MC75A. Set the MC75A’s volume appropriately before putting the headset on. When a Bluetooth headset is connected the speakerphone is muted. It is recommended for phone conversations to use the Bluetooth Hands-free profile instead of the Headset profile. See Chapter 6, Using Bluetooth for more information. NOTE When using a Bluetooth headset during a call, the MC75A power button is disabled and the MC75A will not go into suspend mode. Once the call is completed, the power button functionality is enabled. The following dialog box displays when a Bluetooth headset connection is established. Figure4-5WWAN Bluetooth Audio Notification Dialog Box AdjustingAudioVolume Use the Volume Control Slider or the keypad keys to adjust the volume of the ringer when not in a call and the audio volume when in a call. UsingthePhone 4-5 Figure4-6Phone Volume Slider Phone Volume Slider NOTE AF To adjust the volume tap the Speaker icon in the Title bar. Move the slider up or down to adjust the volume. Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the ring and notification sound levels. MakingaCall NOTE You can make emergency calls even when the MC75A is locked or when a SIM card is not installed. See Making an Emergency Call on page 4-7 for more information. With the MC75A, you can make a call from the phone dialer, contacts, speed dial and call history. UsingthePhoneDialer To make a call using the phone keypad: Tap Start > Phone or press the green phone key on the MC75A’s keypad. 1. 2. From the Phone keypad, tap the number to call. 3. Tap Talk. 4. Tap End to stop dialing or end the call. NOTE Alternatively, use the green and red phone keys on the MC75A keypad to dial (green) and end (red) calls. If you tap a wrong number, tap Delete key to erase each subsequent digit of a number. To erase the entire number, tap and hold the Delete key. UsingContacts Use Contacts to make a call without looking up or entering the phone number. To make a call from Contacts: 1. Tap Start > Contacts. 2. From the contact list, tap and hold the contact name. MC75AEnterpriseDigitalAssistantUserGuide Figure4-7Contacts Menu Tap Call Work, Call Home or Call Mobile. NOTE To make a call from an open contact, tap the number to call. See On-Device Help for more information about Contacts. UsingCallHistory AF 3. 4-6 To make a call using Call History: Tap Start > Phone or press the green phone key on the MC75A’s keypad. 2. From the Phone keypad, tap Call History. Phone icon 1. Figure4-8Call History Window 3. Tap the phone icon next to the number to begin dialing and return to the phone keypad. 4. Tap End or press the red phone key on the MC75A keypad to stop dialing or end the call. MakingaSpeedDialCall Use Speed Dial to call someone saved in the speed dial directory. To make a speed dial call: 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad. UsingthePhone 2. 4-7 From the Phone keypad, tap and hold the speed dial location number assigned to a contact. (To dial a one-digit speed dial location number, tap and hold the speed dial number. To dial a two-digit speed dial location number, tap the first digit and then tap and hold the second digit.) or From the Phone keypad, tap Speed Dial and tap the speed dial location number of the desired contact in the list. Figure4-9Speed Dial Contact List To stop dialing or end the call, tap End or press the red phone key on the MC75A keypad. MakinganEmergencyCall AF 3. Speed Dial Location Number Your service provider programs one or more emergency phone numbers, such as 911 or 999, that you can call under any circumstances, even when your phone is locked or the SIM card is not inserted (on MC75A6). Your service provider can program additional emergency numbers into your SIM card. However, your SIM card must be inserted in your phone in order to use the numbers stored on it. See your service provider for additional information. See Installing the SIM Card on page 1-3 for SIM card installation procedures. Emergency numbers vary by country. Your phone’s pre-programmed emergency number(s) may not work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues. NOTE When the alpha-numeric keypad phone is locked, press the Orange key twice to set the keypad to numeric mode and then enter the emergency number. AnsweringaCall A dialog box appears on the MC75A when it receives an incoming call. If the phone is set to ring, a ring tone sounds. Answer or ignore the incoming call. To answer an incoming call tap Answer on the Phone - Incoming dialog or press the green phone key on the MC75A keypad. MC75AEnterpriseDigitalAssistantUserGuide 4-8 Figure4-10Incoming Call AF To ignore the incoming call tap Ignore. This may send the caller to voice mail, depending on the service provider. Otherwise, this presents busy signal to the calling party. To end the call tap End or press the red phone key on the MC75A keypad. IncomingCallFeatures • If you receive a call while in a call, tap Wait to place the call in call waiting. • You can use other programs on the MC75A during a call. To switch back to Phone, tap Talk or tap Start > Phone. Tap End to end the call. • If a caller isn't in your contact list, create a contact during the call or from Call History by tapping Menu > Save to Contacts. • To terminate a call when a second call comes in and answer the waiting call, tap End on the Phone keypad to disconnect the active call, then tap Answer or press the Send key to answer the waiting call. • To hold the current call and answer a waiting call, tap Answer or press the Send key to place the current call on hold and answer the incoming call. • To put a call on hold to call another number or answer an incoming call, tap Hold on an MC75A6 or Talk on an MC75A8. To move from one call to another, tap Swap on an MC75A6 or Talk on an MC75A8. SmartDialing Smart Dialing makes it easy to dial a phone number. When you start entering numbers or characters, Smart Dialing automatically searches and sorts the contact entries on the SIM card, in Contacts, and the phone numbers in Call History (including incoming, outgoing, and missed calls). You can then select the desired number or contact from the filtered list to dial. Open the Phone screen, then tap the keys on the Phone keypad that correspond to the phone number or contact to call. The contact panel lists contacts that match the sequence that you entered. Smart Dialing starts looking for numbers or contacts that match the sequence entered. To find a phone number: • Enter the first one or two digits to find a phone number in Call History. • Enter the first three digits or more to find a phone number from the saved Contacts and SIM card. UsingthePhone 4-9 To find a contact name: • Enter the first letter of a contact’s first name or last name. Smart Dialing searches for the letter starting from the first character of a contact name as well as from the character that appears after a space, dash, or underscore in a contact name. For example, if you tap number “2” which is associated with [a, b, c] on the Phone keypad, contact names such as the following will be considered matches: “Smith, Bernard”, “Adams, John”, “Carlson, Eileen”, “Dillon, Albert”, “Childs, Larry”, “Cooper, Robert” and “Parks, Celine”. Figure4-11Finding a Contact AF • If the matching list is long narrow down the search further by entering another letter. Using the same example above, tap “3” which is associated with (d, e, f), the matching list is narrowed down to the following names: “Smith, Bernard”, “Adams, John”, and “Parks, Celine”. To make a call or send a text message using Smart Dialing: Begin entering the first few numbers or characters. 2. In the Smart Dialing panel, use the up and down arrows on the keypad to navigate to the desired contact or phone number. 3. When the correct contact is selected, press TALK to make a voice call. 4. To send a text message to the selected contact, tap Menu > Send Text Message. 5. To call a different phone number associated with the selected contact, tap the contact name and select the phone number to call. 1. MutingaCall During a call, you can mute the microphone so you can hear the person on the line but he or she cannot hear conversation from the microphone. This is useful when there is conversation or background noise on your end. To mute or unmute a call: 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad. 2. Make a call. 3. Tap Mute on the display to mute the audio. The Mute icon appears. 4-10 MC75AEnterpriseDigitalAssistantUserGuide Figure4-12Mute Button and Icon AF TakingNotes Mute Icon To create a note during a call, tap Note on the display, then enter the note. For more information about creating notes see the Windows On-Device Help. To access a note created during a call: Tap Start > Phone or press the green phone key on the MC75A’s keypad. 2. From the Phone keypad, tap Call History. 3. Tap and hold the number or the Note icon for the phone call entry containing the note. 1. Note icon Figure4-13Call History - Notes Menu 4. Tap View Note. 5. Tap OK to exit. NOTE Also access notes directly from the Notes application by tapping Start > Notes. UsingthePhone 4-11 UsingSpeedDial Create speed dial numbers to dial frequently called numbers with a single tap. Before creating a speed dial entry, ensure the phone number exists in Contacts. AddingaSpeedDialEntry To add a speed dial entry from the phone keypad: Ensure the contact and phone number are in the Contacts list. 2. Tap Start > Phone or press the green phone key on the MC75A’s keypad. 3. Tap Speed Dial button > Menu > New. AF Tap the desired contact name and number in the list. 4. Figure4-14Contacts 1. Figure4-15Speed Dial Contact Location 5. In the Location field, tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 6. Tap OK to add the contact to the speed dial list. Figure4-16Speed Dial Contact List 7. Tap OK to exit the Speed Dial Contact List. Tap Start > Contacts. 1. AF To add a speed dial entry from the Contacts window: 4-12 MC75AEnterpriseDigitalAssistantUserGuide Figure4-17Contacts 2. Tap a contact name. 3. Tap Menu > Add to Speed Dial. Figure4-18Speed Dial Contact Location UsingthePhone 4-13 4. Tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 5. Tap OK. EditingaSpeedDialEntry Tap Start > Phone or press the green phone key on the MC75A’s keypad. 2. Tap Speed Dial button. AF 1. Figure4-19Speed Dial Contact List Tap and hold the contact name. 4. Tap Edit... . 5. Change the name, phone number, or location information. 6. Tap OK. Editing names and phone numbers in Speed Dial does not alter contact information in Contacts (Start > Contacts). NOTE 3. DeletingaSpeedDialEntry 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad. 2. Tap Speed Dial button. 3. Tap and hold the contact name. 4. Tap Delete. 5. Tap Yes to confirm permanently deleting the speed dial entry. NOTE Deleting names and phone numbers in Speed Dial does not delete the contact information in Contacts (Start > Contacts). 4-14 MC75AEnterpriseDigitalAssistantUserGuide UsingCallHistory Use Call History to call someone who was recently called, or recently called in. Call History provides the time and duration of all incoming, outgoing, and missed calls. It also provides a summary of total calls and easy access to notes taken during a call. Table 4-1 lists the call history icons that appear in the Call History window. Table4-1Call History Icons Icon Description This icon appears next to the contact information for all outgoing calls. This icon appears next to the contact information for all incoming calls. This icon appears next to the contact information for all missed calls. AF ManagingCallHistory Change views, reset the call timer, and delete calls to manage the calls stored in Call History. ChangingtheCallHistoryView Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu > Filter to show the menu. 1. Figure4-20Call History - All Calls/Show Menu 4. Select a view type from the menu to display only missed calls, outgoing calls, incoming calls, or calls listed alphabetically by caller name. 5. Tap OK to exit the Call History window. ResettingtheRecentCallsCounter 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu. Figure4-21Call History - Tools Menu Select Call Timers... . AF 4. UsingthePhone 4-15 Figure4-22Call History - Call Timers Tap Reset. (The All Calls: counter cannot be reset.) 6. Tap OK to exit the Call Timers window. 5. DeletingAllCallHistoryItems 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu. Figure4-23Call History - Tools Menu Select Delete all calls. AF 4. 4-16 MC75AEnterpriseDigitalAssistantUserGuide Figure4-24Call History - Delete All Dialog 5. Tap Yes. 6. Tap OK to exit the Call History window. ViewingCallStatus Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap an entry. The Call Status window appears. 1. Figure4-25Call History - Detail NOTE When more than one call is on the phone line, only the duration of the first call is recorded. UsingthePhone 4-17 4. Tap OK and then OK to exit. UsingtheCallHistoryMenu Use the Call History menu to dial voice mail, access the Activation Wizard, save to contacts, view a note, delete a listing, send a text message, and make a call. Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap and hold an item in the list. Figure4-26Call History - Menu AF 1. Select an applicable item from the menu, as needed. 5. Depending on the item selected, the appropriate window displays. For example, select Send Text Message to display the Inbox window. 6. Tap OK to exit the Call History window. 4. SwappingCallsonanMC75A6 To move between two phone calls: 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad. Figure4-27Call Swapping - Hold Tap Hold on to place the first number on hold. 4. Enter the second number and tap Talk. AF 3. 4-18 MC75AEnterpriseDigitalAssistantUserGuide Figure4-28Call Conferencing - Conferencing Tap Swap to move from one call to the other. 5. 6. Tap End or press the red phone key on the MC75A keypad to end each call. SwappingCallsonanMC75A8 To swap between two incoming phone calls: 1. Tap Answer to connect to the first call. Figure4-29Answer a Call UsingthePhone 4-19 When a second call arrives, tap Answer. The first call is placed on hold. 3. Tap Talk to swap from one call to the other. AF 2. Figure4-30Call Swapping Tap End or press the red phone key on the MC75A keypad to end active call. The remaining call re-connects, tap Answer to connect to the call. 4. 5. Tap End or press the red phone key on the MC75A keypad to end the last call. ConferenceCallingonanMC75A6 NOTE Conference Calling and the number of conference calls allowed may not be available on all services. Please check with your service provider for Conference Calling availability. To create a conference phone session with multiple people: 1. Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad. Figure4-31Conference Call - Hold 4-20 MC75AEnterpriseDigitalAssistantUserGuide Tap Hold to place the first call on hold. 4. Enter the second phone number and tap Talk. 5. After the call is answered, tap Menu > Conference to place the calls in conference mode. AF 3. Figure4-32Creating a Conference Call 6. Tap Hold to place the conference on hold. 7. Enter another phone number and tap Talk. 8. After the call is answered, tap Menu > Conference to place all the calls in conference mode. 9. Repeat steps 6 through 8 for up to six phone numbers. 10. Tap End or press the red phone key on the MC75A keypad to end the conference call. NOTE To speak privately with one party during a conference call, tap Menu > Private. To include all parties again, tap Menu > Conference. UsingthePhone 4-21 Three-wayCallingonanMC75A8 NOTE Three-way Calling may not be available on all services. Please check with your service provider for availability. To create a three-way phone session with two people and you as the initiator: Tap Start > Phone or press the green phone key on the MC75A’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. 3. To call a second person, tap Keypad. Enter the second number and tap Talk. AF 1. Figure4-33Calling Another Person When the second person answers the call, tap Talk to create a three-way calling session. 5. Tap Talk to drop the last call. 6. Tap End to drop the first call. TextMessaging 4. Use the Text Messages window to send and receive text messages to and from mobile phones. The text can contain words, numbers, or an alphanumeric combination no longer than 160 characters. Short text messages delivered over mobile networks transmit from the sending MC75A, are stored in a central short message center, then forwarded to the destination mobile device. If the recipient is not available, the message is stored and can be sent later. ViewingTextMessages To view a text message: You can view a text message whether the phone is on or off. When the phone is on, you can view a text message from its notification callout. Tap the text message notification icon on the navigation bar to display the message. 4-22 MC75AEnterpriseDigitalAssistantUserGuide Figure4-34New Text Message Notification Text Message Notification Icon AF The Caller Identification feature matches incoming text message numbers with those stored in Contacts so you know who is sending you a message. Furthermore, the New Text Message dialog box gives you the option to call the sender or save, dismiss, or delete the message. Figure4-35New Text Message Options When the phone function is off, you can still view received text message in Messaging: 1. Tap Start > Text or on the Today screen, tap the text message on the Information Bar. Tap to View Text Messages. Figure4-36Text Messaging on Today Screen 2. The Text Messages window appears. 3. In the message list, tap the text message. Enter reply here. NOTE AF Figure4-37Text Messages List UsingthePhone 4-23 If the phone is turned off and you tried to call the sender, send a reply, or forward the message, you are prompted to turn the phone function on. SendingaTextMessage To create a text message: On the Phone screen, select a contact name that you want to send a message to. 2. Tap Menu > Send Text Message. 1. Figure4-38Phone Screen Contact List 3. Compose your message. 4-24 MC75AEnterpriseDigitalAssistantUserGuide Address Area Figure4-39Create Text Message Message Area • The auto-correct feature automatically fixes common spelling errors as you type so your messages are more accurate. AF • The character counter lets you see and control the size of the message as you compose. • If you want to know if your text message was received, tap Menu > Message Options, then select the Request message delivery notification check box. 4. Tap Send when you've finished the message. If the phone is turned on, your text message is sent. If it’s off, you are prompted to turn on the phone. If you do so, the message is sent; otherwise when you tap OK, the message is saved in the Drafts folder and sent when the phone is turned on. NOTE If you are out of coverage area, the message is saved in the Drafts folder and sent when you return to a coverage area. On MC75A6 devices, the message remains in the Drafts folder and has to be manually re-sent when you return to a coverage area. UsingaDualLineSIM NOTE Dual Line SIM support is only available on MC75A6 configurations. Check with your service provider for availability. Dual line SIM cards allow for two phone lines on a single card. For example, one line can be a business phone line and the other a personal phone line. To switch between phone lines: 1. Tap Start > Programs > SIM Toolkit. Figure4-40SIM UI Window Select Dual and then tap Select. AF 2. UsingthePhone 4-25 Figure4-41Change Phone Line Select Change and then tap Select. 4. If applicable, sign in with the PIN number for the other line. 3. D AF 4-26 MC75AEnterpriseDigitalAssistantUserGuide Introduction AF Chapter5UsingGPSNavigation The MC75A includes Global Positioning System (GPS) technology using the SiRF III chipset. GPS technology is based on a worldwide system of GPS satellites orbiting the earth that continuously transmit digital radio signals. These radio signals contain data on the satellites’ locations and their exact clock time and are used to determine your location on the earth. When using the MC75A in a vehicle, it is the user’s responsibility to place, secure and use in a manner that will not cause accidents, personal injury or property damage or obstruct their view. It is the responsibility of the driver to operate the vehicle in a safe manner, maintain observation of all driving conditions at all times, and not become distracted by the device to the exclusion of safe driving practices. It is unsafe to operate the controls of the device while driving. WARNING! SoftwareInstallation Third-party GPS navigation software is required. Evaluation software is available from various suppliers. For example; VisualGPS, visit: http://www.visualgps.net/VisualGPSce/ If interested in purchasing GPS navigation software check with the GPS software vendor (before purchasing, downloading, or installing any software) to determine that the application is compatible with the MC75A. Refer to the application’s user guide for application installation and setup information. MC75AGPSSetup The GPS-enabled MC75A operating system automatically manages access to the GPS receiver to allow multiple programs to simultaneously access GPS data. By default, the MC75A has the following settings: 1. Tap Start > Settings > System > External GPS icon. 2. In the Programs tab, the GPS program port is set to COM8. 3. In the Hardware tab, the GPS hardware port is set to GMX1. 5-2 MC75UserGuide Operation Acquiring satellite signals may take a few minutes. It is best to be outside and have a clear, unobstructed view of the sky. Without a clear view, acquisition takes much longer and could result in the MC75A being unable to compute the initial position quickly. When operating the device indoors access to the GPS signals may be limited or unavailable. When using a GPS navigation application, ensure that the MC75A does not go into suspend mode. If the MC75A suspends then the power to the GPS radio is removed. Upon resume the GPS receiver must reacquire a valid GPS signal, resulting in a a delay of positional information. GPSMapsonmicroSDCards NOTE GPS navigation software vendors may sell maps on microSD cards. If using a microSD card with the GPS navigation software: Remove the Memory Card Cover on the side of the MC75A. 2. Insert the microSD card into the slot. 3. Replace the Memory Card Cover. AF 1. AnsweringaPhoneCallWhileUsingGPS If you receive a phone call while using your GPS navigation software: Answer the phone call by pressing the Answer button. 2. Once you end the phone call, press the End Call button to resume the audio on the GPS software. NOTE 1. Anytime you are using GPS on the MC75A and you receive a phone call, the audio on the GPS navigation software is muted until you finish the call. LosingtheGPSSignalWhileinaVehicle GPS performance on the MC75A may be affected if the vehicle has thermal glass windows and windshields, which can block the MC75A from receiving a GPS signal from satellites. To improve GPS signal strength, place the MC75A where there is a clear view of the sky. A direct line of sight is required between the MC75A and the GPS satellites to access information from the satellites. The Global Positioning System (GPS) is a system that allows the user to track their position anywhere on the earth. AssistedGPS GPS can be used in stand-alone or Assisted GPS (A-GPS) modes. A Stand-alone GPS receiver downloads data from GPS satellites. It can take several minutes to get a fix. By using GPS Location servers, A-GPS dramatically improves the performance of the Time To First Fix (TTFF) of GPS receivers by providing them with data that they would ordinarily have to download from the GPS satellites. With the A-GPS data, GPS receivers can operate faster and more reliably. A-GPS follows the Secure User Plane Location (SUPL) protocol which allows the MC75A to communicate with a location server. D Figure5-1SUPL Setup Tab AF UsingGPSNavigation Figure5-2MISC Tab 5-3 T MC75UserGuide AF Figure5-3Info Tab 5-4 T Chapter6UsingBluetooth AF Introduction Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (30 feet/10 meters) communication and low power consumption. MC75As with Bluetooth capabilities can exchange information (e.g., files, appointments, and tasks) with other Bluetooth enabled devices such as phones, printers, access points, and other mobile computers. To use the MC75A as a modem, create a dial-up modem connection between a computer and MC75A. The MC75A with Bluetooth technology uses either the StoneStreet Bluetooth stack or the Microsoft Bluetooth stack. To write an application that uses the StoneStreet One Bluetooth stack APIs, refer to the Enterprise Mobility Developer Kit (EMDK) Help. AdaptiveFrequencyHopping Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work. There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections: • Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask. • Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network. • Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels. • Channel Maintenance - A method for periodically re-evaluating the channels. When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels. AFH coexistence allows Motorola mobile computers to operate in any infrastructure. 6-2 MC75AEnterpriseDigitalAssistantUserGuide The Bluetooth radio in this MC75A operates as a Class 2 device power class. The maximum output power is 2.5mW and the expected range is 32.8 feet (10 meters). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space. NOTE It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required. Security The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures needed to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional. Recommendations are: AF Pairing of Bluetooth devices is accomplished by creating an initialization key that is used to authenticate the devices and create a link key for them. Entering a common PIN number in the devices being paired generates the initialization key. The PIN number is never sent over the air. By default, the Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devices is based-upon a challenge-response transaction. Bluetooth allows for a PIN number or passkey that is used to create other 128-bit keys used for security and encryption. The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult. • Perform pairing in a secure environment • Keep PIN codes private and don't store the PIN codes in the mobile computer • Implement application-level security. The Microsoft stack supports Smart-pairing. For detailed information, refer to the Microsoft MSDN. The StoneStreet One Bluetooth stack supports Secure Simple Pairing. Secure Simple Pairing improves the pairing experience for Bluetooth devices and increasing the use and strength of security. Both the host and the remote device must support Secure Simple Pairing. If one device does not, standard pairing will be used, as described above.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Copy, Extract, Print high-res Author : Motorola, Inc. Copyright : 2009 Create Date : 2010:02:22 09:24:37Z Keywords : "MC75A, mobile computer, MC75A6, MC75A8, MC75A0" Modify Date : 2010:02:23 08:22:14-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : FrameMaker 8.0 Metadata Date : 2010:02:23 08:22:14-05:00 Format : application/pdf Description : MC75A Title : MC75A User Guide Creator : Motorola, Inc. Subject : MC75A, mobile computer, MC75A6, MC75A8, MC75A0 Producer : Acrobat Distiller 9.3.0 (Windows) Document ID : uuid:7687e713-73c9-4586-94b6-1d61fe621c6d Instance ID : uuid:e33cf128-3e4d-4e11-90be-488eb5b1fdeb Page Mode : UseOutlines Page Count : 50EXIF Metadata provided by EXIF.tools