Symbol Technologies SPT1846 2.4 GHz Pen Terminal w/ DSS Internal LAN Radio Car User Manual 5133601 2

Symbol Technologies Inc 2.4 GHz Pen Terminal w/ DSS Internal LAN Radio Car 5133601 2

Users Manual

SPT 1800 Series
SPT 1800 Series© 2001 SYMBOL TECHNOLOGIES, INC. All rights reserved.Symbol reserves the right to make changes to any product to improve reliability, function, or design.Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products.Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.Symbol Technologies, Inc.One Symbol PlazaHoltsville, N.Y. 11742-1300http://www.symbol.comPatentsThis product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No. 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420; 5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,036,098; 6,047,892; 6,050,491; 6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,068,190; 6,082,621; 6,084,528; 6,088,482; 6,092,725; 6,101,483; 6,102,293; 6,104,620; 6,114,712; 6,115,678; 6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379; 6,172,478; 6,176,428; 6,178,426; 6,186,400; 6,188,681; D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581; D414,171; D414,172; D418,500; D419,548; D423,468; D424,035; D430,158; D430,159; D431,562; D436,104.Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan).European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713.rev. 04/01
1Quick ReferenceIntroductionCongratulations on your purchase of Symbol Technologies’ SPT 1800 Series Terminal! The unique combination of capabilities offered by this product makes it superior for use in a wide range of applications:• Personal Information Management software• RF communication via Symbol’s Spectrum24® wireless net-work (SPT 184X) or wide area network (SPT 183X)• pocket size• printing support• 1-D and 2-D scanning capability.About This GuideThis guide covers the procedures for the setup and use of the terminal. Specific topics covered include:•Parts of the SPT 1800 on page 2•Installing the SIM Card (SPT 1834 Only) on page 5•Installing the Battery on page 6•Starting the SPT 1800 on page 8•Using the SPT 1800 on page 9•Writing with the Stylus on page 10•Resetting the SPT 1800 on page 12•Attaching the Handstrap on page 13•Scanning 1-D Bar Codes on page 14•Scanning PDF417 (2-D) Bar Codes on page 14•Initiating a Network Connection on page 15•Maintaining the SPT 1800 on page 16•Troubleshooting on page 17.The SPT 1800 Product Reference Guide (p/n 72-51337-xx), available from Symbol or your Reseller, details the applications available on the SPT 1800.
2SPT 1800 SeriesParts of the SPT 1800The following illustration indicates each part of the SPT 1800. Menu IconFront View Application ButtonsScroll Button (Up and Down)Center Scan ButtonRight Scan TriggerLCD (Screen)Find IconContrast ButtonLaser Decode LEDScroll Button(Up and Down)Applications IconPower ButtonGraffiti Input AreaWAN Antenna(SPT 1833/34 only)Calculator Icon
3Quick ReferenceParts of the SPT 1800 (continued)Bottom ViewTop ViewSerial PortScanner Exit WindowLeft ScanTriggerLeft View
4SPT 1800 SeriesParts of the SPT 1800 (continued)SpeakerHandstrap ConnectorHandstrap ConnectorWAN AntennaBack ViewStylus Stylus SiloHandstrap ConnectorsBattery LatchesLithium-Ion BatteryReset ButtonInfrared PortSIM SocketBattery CompartmentWAN AntennaHeadset ConnectorBattery Cover
5Quick ReferenceGetting StartedBefore you can use your SPT 1800, perform the basic setup procedures:•Install the SIM card (SPT 1834 only)•Install and charge the battery•Start the SPT 1800•Initiate the network connection (SPT 183X/184X only).Installing the SIM Card (SPT 1834 Only)Open the latches on the battery cover and lift it away from the SPT1834.Metal ClipSIM CardContact Area1. Slide the metal clip to the left to release the SIM cardholder.2. Lift the cardholder to an upright position.3. Insert the card between the cardholder body and the metal clip; be sure the beveled corner of the SIM card is on the top.4. Close the cardholder (with the contact area of the card facing down.5. Slide the metal clip to the right to lock it in place.
6SPT 1800 SeriesInstalling the Battery1. Open the latches on the battery cover and lift it away from the SPT 1800.2. Insert the lithium-ion (Li-ion) battery into the battery compartment, ensuring that it snaps into place.3. Replace the battery cover and close the latches.Note: Keep the battery latches completely open while securing the battery cover.Charging the BatteryNote: The SPT 1800 battery (p/n 20-36098-01) must be used only with the SPT 1800.Before using your SPT 1800 for the first time, charge the battery using the cradle, the Synchronization/Charging Cable or the Universal Battery Charger (UBC). For instructions on using the UBC, see the UBC Quick Reference Guide. Caution: The main battery charges the backup battery in the SPT 1800. Once the battery is fully charged, do not re-move it from the SPT 1800 for 24 hours. During this pe-riod, the SPT 1800 cannot maintain any user data if the battery is removed from the terminal.LatchLatch
7Quick ReferenceUsing the Cradle to Charge the Battery1. Ensure the battery is installed in the terminal.2. Plug the cradle into a wall outlet.3. Insert the SPT 1800 into the cradle.The terminal’s battery is fully charged after approximately two hours. You can also charge a spare battery by inserting it into the spare battery charging slot on the back of the single slot cradle. The spare battery fully charges in approximately two hours. See the CRD 1700 Cradle Quick Reference Guide for more information.Note: When the battery is fully charged, the cradle’s charging LED lights green. On older CRD 1700 single slot and modem cradles, the charging LED may not illuminate green when the terminal’s battery is fully charged.Using the Synchronization/Charging Cable to Charge the Battery1. Ensure the battery is installed in the terminal.2. Insert the cable into the bottom of the terminal.Synchronization/Charging Cable
8SPT 1800 Series3. Plug the power cable into a wall outlet and plug the other end into the battery charging receptacle on the side of the Syn-chronization/Charging Cable.The battery is fully charged after approximately two hours.Starting the SPT 1800Press the red power button to power on the terminal. If the terminal does not power on, perform a hard reset. See Performing a Hard Reset on page 12.Calibrating the ScreenThe first time you start your SPT 1800, the Welcome utility appears. Follow the steps to align the internal circuitry of your SPT 1800 with its touch-sensitive screen, and to set the current time and date.Note: If your SPT 1800 unit came pre-loaded with a custom software application, you may not need to calibrate your screen, in which case you will not see the Wel-come utility.Battery ChargingReceptaclePowerSupplySerial Cable
9Quick Reference1. Press the power button on the front panel of your SPT 1800 to display the Welcome utility. (This also displays following a hard reset).Note: If necessary, adjust the contrast control on the SPT 1800 so the screen is clear and readable. See Contrast Control on page 10 for instructions.2. Follow the instructions on the screen.3. Tap the exact center of each target that appears on the screen with the tip of the stylus.If, at any time, you need to recalibrate the screen, open the Preferences application, tap General on the top right corner of the screen, and select the digitizer option from the pull down menu.Using the SPT 1800Power Button/Backlight ControlThe power button turns the SPT 1800 on and off. This button also serves as your backlight control for low-light conditions. When the SPT 1800 is on, press and hold the power button for approximately two seconds to turn the backlight on and off.PowerButton
10SPT 1800 SeriesContrast ControlThe contrast control button is located on the lower right-hand side of the SPT 1800.1. Press the contrast control button to display the contrast ad-justing bar on the screen.2. Using your stylus, adjust the contrast by scrolling the con-trast bar until the contrast is set to the desired level, or use either of the scroll buttons on the top of the terminal to adjust the contrast level.3. Press the contrast control button or tap Done on the screen to turn off the contrast control.Writing with the StylusYour SPT 1800 includes Graffiti® handwriting software for entering text and numbers. Graffiti translates stylus strokes into letters or numbers. See the SPT 1800 Product Reference Guide, p/n 72-51337-xx for more information.On-screen KeyboardYou can activate the on-screen keyboard any time you need to enter text or numbers on your SPT 1800. Note that you cannot enter Graffiti characters while using the on-screen keyboard.1. Open any application.2. Tap any record name, or tap the New button with the tip of the stylus.Contrast Control
11Quick Reference3. Tap the left target to open the Alpha keyboard, or tap the right target to open the Numeric keyboard.Icon DescriptionsUsing a Headset (SPT 1834 Only)To use a headset with the SPT 1834, plug the headset jack into the audio connector on the top of the terminalApplications Icon Exits the current application and lists available applications for selection.Calculator Icon Displays the calculator application.Menu Icon Tap from within an application to display the options menu for the application.Find Icon Tap from within an application to enter search criteria to find an entry.Tap here for letters keyboardTap here for numbers keyboard
12SPT 1800 SeriesResetting the SPT 1800If your SPT 1800 stops responding to input, you may need to perform a reset.Performing a Soft ResetA soft reset restarts the SPT 1800 and saves all records and entries stored in your SPT 1800 terminal. After a soft reset, the Palm Computing Platform® Logo screen appears followed by the General Preferences screen.To perform a soft reset, remove the battery cover and gently press the reset button located under the battery cover.Performing a Hard ResetA hard reset also restarts your terminal, but erases all records and entries stored in your SPT 1800. Therefore, never perform a hard reset unless a soft reset does not solve your problem.Note: You can restore any data previously synchronized with your computer during the next HotSync operation.1. Remove the battery cover.2. Hold down the power button on the front of the SPT 1800, and gently press the reset button.3. Release the reset button, then release the power button when the Palm logo appears.4. When a message appears on the screen warning that you are about to erase all data, do one of the following:a. Press the upper half of a scroll button to complete the hard reset.b. Press any other button to perform a soft reset.Reset button
13Quick ReferenceNote: With a hard reset, the current date and time are re-tained. Formats, preferences and other settings are re-stored to their factory default settings.Attaching the HandstrapThe SPT 1800 has a handstrap which increases comfort when holding it for extended periods of time. To attach the handstrap for the SPT 1834:1. Put the side slots of the thread-ed button over the wire clips on the handstrap.2. Screw the button into the threaded slot on the back of the terminal.3. Slide the flat metal piece into the handstrap connection on the bottom of the terminal.1. Thread round metal piece through this connector.3. Adjust the velcro strap to fit your hand. 2. Slide flat metal piece up and into this connector.
14SPT 1800 SeriesScanning 1-D Bar CodesThe SPT 1800 has an integrated laser bar code scanner which allows you to collect data by scanning bar codes if your unit is configured with a scanning application. To scan bar codes:1. Start your scanning application.2. Aim the scanner at a bar code.3. Press either the right, left or center scan trigger. Make sure the red scan beam covers the entire bar code. The green scan LED lights and a beep sounds to indicate a successful decode.Scanning PDF417 (2-D) Bar CodesTo scan a PDF417 bar code (with a 2-D configured terminal):1. Aim the scanner at the PDF bar code and press either the right, left, or center scan trigger.2. Hold the trigger down and keep the scan line parallel to the rows of the symbol.3. Manually raster the scan line by slowly moving the scanner up and down so it scans the entire bar code at a rate of one inch per second.Center Scan Button1/2” 1/2”Scan Line
15Quick ReferenceA clicking noise lets you know the 2-D bar code is being decoded. If there is no clicking noise when you are scanning, the bar code is not being scanned properly.When decoding a very long 2-D bar code, you may notice a slight delay between the time when the terminal completes the decode and the time when the data is displayed on the screen. The first beep you hear indicates a successful decode. The second beep you hear indicates the data has been received by the host. Do not attempt to decode another bar code until you hear the second beep and see the green LED indicating a successful decode.To improve PDF decoding:•Check that PDF417 scanning is enabled.•Make sure the scan line extends at least 1/2” past the left and right edges of the bar code.•Hold the scanner closer for denser symbols, farther away for larger symbols.•Make sure you scan the top and bottom rows of the symbol.•Be patient - it may take a few swipes to decode the symbol.The bar code is completely decoded when you hear a tone, followed by a short, high tone beep. The green LED stays lit for three seconds or until the next trigger pull.Initiating a Network ConnectionBefore using the terminal, set up the Spectrum24, CDPD (Cellular Digital Packet Data) or GSM (Global System for Mobile Communication) network connection. Refer to the SPT 1800 Series Product Reference Guide, p/n 72-51337-xx for setup instructions.A small cursor blinks at the top right-hand corner of the screen when the terminal activates a radio connection (Spectrum24 or CDPD). A blinking cursor does not appear for a GSM radio
16SPT 1800 Seriesconnection. A cursor does not appear if you are not connected to the radio.Maintaining the SPT 1800For trouble-free service, observe the following tips when using your SPT 1800:•Do not scratch the screen. Use the supplied stylus or a plas-tic-tipped pen intended for use with a touch-sensitive screen. Never use a pen or pencil or other sharp object on the screen.•Although your SPT 1800 is water and dust resistant, do not expose it to rain or moisture for an extended period. Treat your SPT 1800 as you would a pocket calculator or other small electronic instrument.•The touch-sensitive screen of your SPT 1800 contains glass. Do not subject your SPT 1800 to any strong impact.•Protect your SPT 1800 from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heaters and other heat sources.•Do not store or use your SPT 1800 in any location that is ex-tremely dusty, damp or wet.•If the surface of the SPT 1800 screen becomes soiled, clean it with a soft lens cloth moistened with a diluted window-cleaning solution.
17Quick ReferenceTroubleshootingProblem Cause SolutionSPT 1800 terminal does not turn on. Contrast is set too light. Adjust the contrast control.Battery is not ful-ly charged. Make sure the battery is fully charged and installed properly.Battery is defec-tive. Replace the battery. If your SPT 1800 terminal still does not operate, try a soft reset; see Resetting the SPT 1800 on page 12.Low battery warning after replacing the battery.A normal condi-tion. The battery warning message may ap-pear immediately after replacing the battery. In addition, if you check the battery gauge in the Applications Launcher immediately after replacing the battery, the gauge may start at “empty” and slowly rise to “full.” This is normal. It takes a minute for the battery gauge to accurately show the condition of the battery.No sound. Sound setting is set to off in the Preferences sec-tion.Check the Sound options in the Gener-al Preferences screen. If an option is set to off, there will be no sound. Tap the “off” setting to display a menu of options and tap the option you want.SPT 1800 terminal turns itself off. Terminal auto-matically turns it-self off after a period of inactivi-ty.Your SPT 1800 is designed to turn it-self off after a period of inactivity. This period can be set at thirty seconds, one minute, two minutes or three min-utes. Check the “Auto-off after” setting in the General Preferences screen, and change the setting if you need a longer delay before the automatic shutoff feature activates. See the SPT 1800 Product Reference Guide for more information. Note: The terminal also turns itself off when the battery power is extremely low.
18SPT 1800 SeriesSPT 1800 doesn’t recognize my hand-writing.You are not using Graffiti character strokes.For your SPT 1800 to recognize hand-writing input with the stylus, you need to use the Graffiti® character strokes. See the SPT 1800 Product Reference Guide for information about how to write Graffiti character strokes.You are not writ-ing character strokes in the correct area.Make the Graffiti character strokes in the Graffiti writing area — not on the display part of the screen.Make sure you are writing the strokes for letters in the left-hand side, and the strokes for numbers in the right-hand side of the Graffiti writing area.Graffiti is shifted into extended or punctuation modes.See the SPT 1800 Product Reference Guide for information about shifting into and out of punctuation modes.Tapping the screen buttons or icons does not activate the corresponding fea-ture.Screen is out of calibration. Recalibrate the digitizer. Choose Digi-tizer from the Preferences application pick list and follow the directions on the screen.When I tap the Menu icon, nothing hap-pens.Application does not have menu item.Not all applications or screens have menus. Try changing to a different ap-plication.Beamed data does not transmit. Terminals are too far apart or ob-structed. File is locked.Confirm that the SPT 1800 terminals are 5” apart, the receiver has its IrDA capability enabled, and that the path between the two devices is clear of ob-stacles.Note: You cannot overwrite a .prc file via IrDA if it is locked.When receiving beamed data an out of memory message appears.Memory full. Your SPT 1800 terminal requires at least twice the amount of memory available as the data you are receiving. For example, if you are receiving a 30K application, you must have at least 60K free.Problem Cause Solution
19Quick ReferenceErgonomic RecommendationsCaution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.•Reduce or eliminate repetitive motion•Maintain a natural position•Reduce or eliminate excessive force•Keep objects that are used frequently within easy reach•Perform tasks at correct heights•Reduce or eliminate vibration•Reduce or eliminate direct pressure•Provide adjustable workstations•Provide adequate clearance•Provide a suitable working environment•Improve work procedures.SPT 1800 does not accept scan input. Scan application not present. Verify that the SPT 1800 is loaded with a scanning application. See your Sys-tem Administrator.Bad bar code. Check to be sure the bar code symbol is not defaced.Too far away from bar code. Be sure you are within proper scanning range.Bar code type is not enabled. Be sure the SPT 1800 is programmed to accept the type of bar code you are scanning.Beep is not en-abled. If you are expecting a beep on a good decode and don’t hear one, check that the application is set to generate a beep on good decode.Battery is low. If the scanner stops emitting a laser beam when you press the trigger, check your battery level. When the bat-tery is low, the scanner shuts off before the terminal notifies you of the low bat-tery condition.Note: If, after performing these checks, the scanner is still not reading sym-bols, contact your distributor or Symbol Technologies.Problem Cause Solution
20SPT 1800 SeriesRegulatory InformationRadio Frequency Interference RequirementsThis device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulations. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Re-orient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that on which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.Important Note: To comply with FCC and Industry Canada RF exposure requirements, this hand-held device is approved for operation in a user's hand when there is 20 cm or more between the antenna and the user's body.Radio Frequency Interference Requirements - CanadaThis device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
21Quick ReferenceCE Marking and European Union ComplianceProducts intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included:Applicable Directives•Electromagnetic Compatibility Directive 89/336/EEC•Low Voltage Directive 73/23/EECApplicable Standards•EN 55022:1998, Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipment•EN 55024:1998; Information Technology equipment - Immunity characteristics - Limits and methods of measurement•IEC 1000-4-2:1995; Electromagnetic compatibility (EMC); Part 4:Testing and measurement techniques; Section 4.2:Electrostatic discharge immunity test•IEC 1000-4-3:1997; Electromagnetic Compatibility (EMC); Part 4:Testing and measurement techniques; Section 3. Radiated, radio frequency, electromag-netic field immunity test.•IEC 1000-4-4:1995; Electromagnetic compatibility (EMC); Part 4: Testing and measurement techniques; Section 4:Testing electrical fast transient,/Burst immunity.•IEC1000-4-5:1995; Electromagnetic compatibility (EMC), Part 4: Testing and measurement techniques; Section 5: Surge Immunity•IEC 1000-4-6:1996; Electromagnetic compatibility (EMC), Part 4:Testing and measurement techniques; Section 6: Immunity to conducted disturbances, induced by radio frequency fields.•IEC 1000-4-11:1994; Electromagnetic compatibility (EMC), Part 4: Testing and measurement techniques; Section 11: Voltage Dips, Short Interruptions, and Voltage Variations.•EN 60 950 + A1+A2+A3+A4+A11 - Safety of Information Technology Equip-ment Including Electrical Business Equipment•EN 60 825-1 (EN 60 825) - Safety of Devices Containing Lasers RF DevicesSymbol’s RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and will be labeled as required. The majority of Symbol’s RF devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any changes or modifications to Symbol Technologies equipment not expressly approved by Symbol Technologies could void the user’s authority to operate the equipment.The Spectrum24 equipment is intended for use throughout the European Economic Area, but its authorization for use in France is restricted as follows:
22SPT 1800 Series•PAN European Frequency Range: 2.400 - 2.4835 GHz, identified by -EU suffix to the model number found on the product label.•France - Restrict Frequency Range for use in France: 2.4465 - 2.4835 GHz, identified on SPT 1842 by the -FR suffix to the model number found on the product label.•Belgium - Operation in an out-of-doors environment in Belgium must be restricted to 2.460 - 2.4835 GHz band.•Italy - Operation in Italy requires a user license. GSM Regulatory WarningsEmergency CallsPlease contact your service provider for information about the availability of Emergency Calls.The GSM version supports Emergency Calls with or without a SIM card fitted. However, as for any other voice call, you must be registered on a GSM network. If you are outside the coverage of a GSM network, or another factor such as insufficient power occurs, then Emergency Call will not work.The procedure for generating an Emergency Call will depend on the application/ service currently in use and the network you are connected to. It is recommended that you familiarize yourself with the appropriate procedures required to generate an Emergency Call.When connected to the Emergency Operator you should have details of your telephone number and location on hand.Safety InformationThe GSM version emits radio frequency signals in the 900 MHz, 1800 MHz and 1900 MHz frequency bands. The following recommendations are in line with guidelines concerning public exposure to radio frequency electromagnetic energy, issued by various European and International agencies.Unlike a mobile phone, the transmitter antenna on the GSM version would not (under normal circumstances) be close to the head, and therefore high field strength is not usually encountered. The use of the GSM version is similar to using a mobile phone with a handsfree unit. However, take care to avoid placing any part of your body in proximity to the GSM version antenna when the GSM radio is switched on. In
23Quick Referenceparticular, it is recommended that you do not grasp the antenna while the GSM version is operating as this will not only significantly degrade its performance, but also expose your hand to the maximum radio frequency power emitted by the GSM version.Safety on the RoadThe GSM version should not be used by the driver of a vehicle when in motion. Always safely park your vehicle before turning your attention to your device. Always adequately secure your device in a moving vehicle, and do not leave it loose on a passenger seat. Remember that in the event of a sudden stop an unsecured device could cause injury to any occupants as well as damage to the vehicle. If your vehicle has an airbag, do not place any objects, including your device, in the area around the airbag or where the airbag deploys. Any item propelled by an activated airbag could cause serious injury and damage. When receiving calls on a public highway, mobile units are not permitted to use “warning” devices, which permit the vehicles' horn to sound or the light to flash. Safety on AircraftYou are required by law to switch off all electrical apparatus when boarding and leaving an aircraft and at any other time when instructed to do so by a member of the crew. You are not allowed to use any mobile phone, as well as the GSM version, at any time when on board an aircraft, as such use may constitute a danger. In such circumstances please ensure that your GSM version is switched off, disabling attempts to log onto networks. PacemakersIt is recommended by pacemaker manufacturers that a minimum of 20cm (8 inches) be maintained between a handheld wireless phone and a pacemaker to avoid any possible interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research.Hearing AidsSome digital wireless phones may interfere with some hearing aids. In the event of such interference you may want to consult your hearing aid supplier to discuss solutions.Persons with pacemakers:•Should always keep the phone more than 20cm (8 inches) from their pace-maker when the phone is turned on.•Should not carry the phone in a breast pocket.•Should use the ear opposite the pacemaker to minimize the potential for inter-ference.
24SPT 1800 SeriesIf you have any reason to suspect that interference is taking place, turn off the GSM version immediately. This may be achieved most rapidly by switching off the device using its on/off button.Other Medical DevicesThe GSM version transmits radio frequency energy and as such has the potential to interfere with inadequately protected medical devices. Consult your physician or the manufacturer of the device to see if any particular device has sufficient protection.It is good practice to completely turn off the GSM version within a hospital or other medical facility where sensitive medical equipment is in use. In some countries, this is a legal requirement applying to all mobile phones and related equipment. Effect on VehiclesRF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle.Posted FacilitiesSwitch off the GSM version in any facility where posted notices require mobile phones to be switched off.Potentially Hazardous AtmospheresDo not take a GSM version into any area with a potentially hazardous atmosphere. The GSM version is not rated for use in such environments and therefore such use may pose a threat of explosion. Such areas are often, but not always, clearly marked. They may include below decks on boats; chemical transfer or storage facilities; fuel filling stations; areas where fuel odors are present such as in a tent or caravan where cooking or heating by bottled gas is taking place; fuel transfer or storage facilities; vehicles using liquid petroleum gas (lpg); areas where the air contains concentrations of grain, dust or metal powders; and any area where you would normally be advised to turn off your vehicle engine.Blasting AreasTo avoid interference with any blasting operations, turn off your GSM version when in a blasting area and other areas where the use of radio equipment is prohibited. Obey all signs and instructions.Laser DevicesSymbol products using lasers comply with US 21CFR1040.10, and IEC825-1:1993, EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels on the product.
25Quick ReferenceClass 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.Battery CautionCaution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dis-pose of used batteries according to the manufacturer's instructions.Scanner LabelingSPT 1800 SPT 1834
26SPT 1800 SeriesIn accordance with Clause 5, IEC 0825 and EN60825, the following information is provided to the user:ENGLISH HEBREWCLASS 1 CLASS 1 LASER PRODUCTCLASS 2 LASER LIGHTDO NOT STARE INTO BEAMCLASS 2 LASER PRODUCTDANISH ITALIANKLASSE 1 KLASSE 1 LASERPRODUKT CLASSE 1 PRODOTTO AL LASER DI CLASSE 1KLASSE 2 LASERLYF CLASSE 2 LUCE LASERSE IKKE IND I STRÅLEN NON FISSARE IL RAGGIOPRODOTTOKLASSE 2 LASERPRODUKT AL LASER DI CLASSE 2DUTCH NORWEGIANKLASSE 1 KLASSE-1 LASERPRODUKT KLASSE 1 LASERPRODUKT, KLASSE 1KLASSE 2 LASERLICHT KLASSE 2 LASERLYS IKKE STIRR INN I LYSSTRÅLENNIET IN STRAAL STAREN LASERPRODUKT, KLASSE 2KLASSE-2 LASERPRODUKTFINNISH PORTUGUESELUOKKA 1 LUOKKA 1 LASERTUOTE CLASSE 1 PRODUTO LASER DA CLASSE 1LUOKKA 2 LASERVALO CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO LUMINOSOÄLÄ TUIJOTA SÄDETTÄPRODUTO LASER DA CLASSE 2LUOKKA 2 LASERTUOTEFRENCH SPANISHCLASSE 1 PRODUIT LASER DE CLASSE 1 CLASE 1 PRODUCTO LASER DE LA CLASE 1CLASSE 2 LUMIERE LASER CLASE 2 LUZ LASERNE PAS REGARDER LE RAYON FIXEMENT NO MIRE FIJAMENTE EL HAZPRODUIT LASER DE CLASSE 2 PRODUCTO LASER DE LA CLASE 2GERMAN SWEDISHKLASSE 1 LASERPRODUKT DER KLASSE 1 KLASS 1 LASERPRODUKT KLASS 1KLASSE 2 LASERSTRAHLEN KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLENNICHT DIREKT IN DEN LASERSTRAHL SCHAUEN LASERPRODUKT KLASS 2LASERPRODUKT DER KLASSE 2
27Quick ReferenceDECLARATION OF CONFORMITYWe, Symbol Technologies, Inc.of One Symbol Plaza, Holtsville, NY 11742-1300, USAdeclare under our sole responsibility that the product(s)Spectrum24, LA302T, Type II Radio CardSpectrum24HR, LA411T, Type II Radio CardSpectrum24HR, LA412T, Type II Radio Cardto which this declaration relates, are in conformity with the following standards and/or other normative documents.ETS 300 328 (November 1996)ETS 300 826 (November 1997)EN 60950: 1992 Incl Amdt 1-4, 11We hereby declare that all essential radio test suites have been carried out and that the above named products are in conformity with all the essential requirements of Directive 1999/5/EC.The conformity assessment procedure referred to in Article 10(5) and detailed in Annex IV ofDirective 1999/5/EC has been followed with the involvement of the following Notified Body(ies):BABT, Claremont House, 34 Molesey Road, Walton-on-Thames, KT12 4RQIdentification mark: 0168 The equipment will also carry the Class 2 equipment identifierThe technical documentation relevant to the above equipment can be made available for inspection on application to:Symbol Technologies EMEA, Symbol Place, Winnersh Triangle, Berkshire, RG 41 5TP, UKDornu Narnor(name)Director, Regulatory and Technical Sales(title)3, May 2000(signature of authorised person) (date)
28SPT 1800 Series
29Quick ReferenceWarrantySymbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmanship. This warranty is provided to the original owner only and is not transferable to any third party. It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii) which has not been maintained in accordance with any operating or handling instructions supplied by Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse, abuse, power shortage, negligence or accident or (iv) which has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of customer and is not covered under this warranty. Wear items and accessories having a Symbol serial number, will carry a 90-day limited warranty. Non-serialized items will carry a 30-day limited warranty.Warranty Coverage and ProcedureDuring the warranty period, Symbol will repair or replace defective products returned to Symbol’s manufacturing plant in the US. For warranty service in North America, call the Symbol Support Center at 1-800-653-5350. International customers should contact the local Symbol office or support center. If warranty service is required, Symbol will issue a Return Material Authorization Number. Products must be shipped in the original or comparable packaging, shipping and insurance charges prepaid. Symbol will ship the repaired or replacement product freight and insurance prepaid in North America. Shipments from the US or other locations will be made F.O.B. Symbol’s manufacturing plant. Symbol will use new or refurbished parts at its discretion and will own all parts removed from repaired products. Customer will pay for the replacement product in case it does not return the replaced product to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange. Customer accepts full responsibility for its software and data including the appropriate backup thereof. Repair or replacement of a product during warranty will not extend the original warranty term. Symbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or phone support, that can be implemented to meet customer’s special operational requirements and are available at a substantial discount during warranty period. GeneralExcept for the warranties stated above, Symbol disclaims all warranties, express or implied, on products furnished hereunder, including without limitation implied warranties of merchantability and fitness for a particular purpose. The stated express warranties are in lieu of all obligations or liabilities on part of Symbol for damages, including without limitation, special, indirect, or consequential damages arising out of or in connection with the use or performance of the product. Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way exceed the purchase price of said product, except in instances of injury to persons or property. Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential damages, so the preceding exclusion or limitation may not apply to you.
72-51336-01Revision A — May 2001Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300Service InformationBefore you use the unit, it must be configured to operate in your facility’s network and run your applications.If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center:Visit http://www.symbol.com/manuals for all product manuals.United States 1-800-653-5350 Canada 905-629-7226United Kingdom 0800 328 2424 Asia/Pacific 337-6588 Australia 1-800-672-906 Austria 1-505-5794Denmark 7020-1718 Finland 9 5407 580France 01-40-96-52-21 Germany 6074-49020Italy 2-484441 Mexico 5-520-1835Netherlands 315-271700 Norway 66810600South Africa 11-4405668 Spain 9-1-320-39-09Sweden 84452900Latin America Sales Support 1-800-347-0178 Inside US+1-561-483-1275 Outside USEurope/Mid-East Distributor Operations Contact local distributor or call+44 208 945 7360

Navigation menu