Symbol Technologies Scanner Ds 3408 Users Manual T

LS 3408 to the manual 94ff0c48-31d5-40a0-83b0-713f0b25ac94

2015-02-02

: Symbol-Technologies Symbol-Technologies-Symbol-Technologies-Scanner-Ds-3408-Users-Manual-449055 symbol-technologies-symbol-technologies-scanner-ds-3408-users-manual-449055 symbol-technologies pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

4
3
1
1234
2
LS/DS 3408
http://www.symbol.com/barcode
See Product Reference Guide for more information
POST IN WORK AREAPOST IN WORK AREA
1 Tether Plate
2 LED Indicators
3 Scan Window
4 Scan Trigger
Variants
Accessories
Laser Scanner
(ER, FZ) Digital Scanner
(DS)
IntelliStand Forklift Holder
Cord Attachment
Host Interfaces
NOTE: Cables may vary depending on configuration
Troubleshooting
IBM 46XX
USB
RS-232 Keyboard Wedge
Wand Emulation
Scanner Emulation
No power to scanner
Check system power;
ensure power supply,
if required, is connected
Incorrect interface cable used
Ensure that correct
interface cable is used
Interface/power cables are loose
Check for loose cable
connections
Scanner not working
Bar code unreadable
Ensure bar code is not defaced;
try scanning test bar code of same
bar code type
Distance between scanner
and bar code incorrect
Move scanner closer to
or further from bar code
Scanner not programmed
for bar code type
Ensure scanner is programmed
to read type of bar code being
scanned
Scanner not decoding bar code
Scanner not programmed for correct host interface
Check scanner host parameters or edit options
Interface cable is loose
Check for loose cable connections
Scanner decoding bar code, but data not transmitting to host
Scanner not programmed for correct host interface
Check scanner host parameters or edit options
Scanned data incorrectly displayed on host
Set Defaults
LS/DS 3408 Programming Bar Codes
RS-232 Host Types Carriage Return/Line Feed
Wand Emulation Host Types
Keyboard Wedge Host Types
USB Host Types
IBM 46XX Host Types
SET DEFAULTS
HID KEYBOARD EMULATION
IBM HAND-HELD USB
PORT 5B
PORT 9B
STANDARD RS-232
ICL RS-232
NIXDORF RS-232 MODE A
SYMBOL WAND
ENABLE CONVERT TO CODE 39
DISABLE CONVERT TO CODE 39
SCAN OPTIONS
<DATA><SUFFIX>
ENTER
NIXDORF RS-232 MODE B
FUJITSU RS-232
OPOS/JPOS
IBM PC/AT and IBM PC COMPATIBLE
Quick Start Guide
SYMBOL TECHNOLOGIES, INC. One Symbol Plaza Holtsville, New York 11742-1300
012345
012345 012345
012345
4
3
1
2
Optimum Upright Body Posture
Avoid Extreme Wrist Angles
Low/medium/high beep
Power up
Short high beep
Bar code decoded
[if decode beeper
enabled]
4 long low beeps
Transmission error
detected; data is
ignored
Standard Use
High/low beep
Correct programming
sequence performed
Low/high beep
Incorrect
programming
sequence or
Cancel bar code
scanned
High/low/high/low beep
Successful
parameter
setting
Parameter Menu Scanning
Beeper Indications
LED Indications
Off
Scanner is on
and ready to scan,
or no power to
scanner
Green
Bar code is successfully
decoded
Red
Transmission
error
LS/DS 3408 Recommended Usage Guide
Local Contact:
POST IN WORK AREAPOST IN WORK AREA
http://www.symbol.com/barcode
72-67131-02 Revision A June 2004
Optimum Scanning Positions
TAKING BREAKS AND TASK ROTATION RECOMMENDEDTAKING BREAKS AND TASK ROTATION RECOMMENDED
ALTERNATE LEFT AND RIGHT HANDSALTERNATE LEFT AND RIGHT HANDS
Laser Scanner
(ER, FZ)
Aiming Digital Scanner
(DS)
1 Tether Plate
2 LED Indicators
3 Scan Window
4 Scan Trigger
Optimum Body Posture
for Low Scanning ALTERNATE LEFT
AND RIGHT KNEES
Optimum Body Posture for
Extended Range Scanning
LS/DS 3408
http://www.symbol.com/barcode
72-67131-02 Revision A June 2004
Tested to comply
with FCC S tandards
FOR HOM E OR OFFICE U S E
Regulatory Information
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow
the recommendations below. Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety programs to prevent
employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
All Symbol devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly
approved by Symbol Technologies, could void the user's authority to operate the
equipment.
Antenna’s, use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could cause damage and
may violate regulations.
Radio Frequency Interference Requirements
  Note: This equipment has been tested and 
found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC 
rules. These limits are designed to provide 
reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Symbol Technologies, Inc., hereby declares that this device is in compliance with all
the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may
be obtained from http://www2.symbol.com/doc
©2004 SYMBOL TECHNOLOGIES, INC. All rights reserved.
Symbol reserves the right to make changes to any product to improve reliability, function, or
design. Symbol does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein. No license is granted,
either expressly or by implication, estoppel, or otherwise under any patent right or patent,
covering or relating to any combination, system, apparatus, machine, material, method, or process
in which Symbol products might be used. An implied license exists only for equipment, circuits,
and subsystems contained in Symbol products. Symbol and the Symbol logo are registered
trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be
trademarks or registered trademarks of their respective companies and are hereby
acknowledged.
Symbol Technologies, Inc., One Symbol Plaza, Holtsville, N.Y. 11742-1300, http://www.symbol.com
Patents
This product is covered by one or more of the following U.S. and foreign Patents:
U.S. Patent No. 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095;4,758,717; 4,760,248;
4,806,742; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833;
5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550;
5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167;
5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398;
5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,324,924; 5,337,361;
5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140;
5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042;
5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610;
5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531;
5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800;
5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863;
5,767,500; 5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520;
5,823,812; 5,828,050; 5,848,064; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989;
5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420; 5,945,658; 5,945,659;
5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,029,894; 6,031,830; 6,036,098; 6,047,892; 6,050,491;
6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,082,621; 6,084,528; 6,088,482; 6,092,725; 6,101,483;
6,102,293; 6,104,620; 6,114,712; 6,115,678; 6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379;
6,172,478; 6,176,428; 6,178,426; 6,186,400; 6,188,681; 6,209,788; 6,209,789; 6,216,951; 6,220,514;
6,243,447; 6,244,513; 6,247,647; 6,308,061; 6,250,551; 6,295,031; 6,308,061; 6,308,892; 6,321,990;
6,328,213; 6,330,244; 6,336,587; 6,340,114; 6,340,115; 6,340,119; 6,348,773; 6,380,949; 6,394,355;
D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124;
D391,250; D405,077; D406,581; D414,171; D414,172; D418,500; D419,548; D423,468; D424,035;
D430,158; D430,159; D431,562; D436,104.
Invention No. 55,358; 62,539; 69,060; 69,187, NI-068564 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269
(Japan); European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy
1,138,713
rev. 06/02
Service Information
Before you use the unit, it must be configured to operate in your facility’s
network and run your applications.
If you have a problem running your unit or using your equipment, contact
your facility’s Technical or Systems Support. If there is a problem with the
equipment, they will contact the Symbol Support Center:
United States 1-800-653-5350 or 1-631-738-2400
Canada 905-629-7226
United Kingdom 0800 328 2424
Asia/Pacific +65-6796-9600
Australia 1-800-672-906
Austria/Österreich 1-505-5794-0
Denmark/Danmark 7020-1718
Finland/Suomi 9 5407 580
France 01-40-96-52-21
Germany/Deutchland 6074-49020
Italy/Italia 2-484441
Mexico/México 5-520-1835
Netherlands/Nederland 315-271700
Norway/Norge +47 2232 4375
South Africa 11-8095311
Spain/España 91 324 40 00 (Inside Spain)
+34 91 324 40 00 (Outside Spain)
Sweden/Sverige 84452900
Latin America Sales Support 1-800-347-0178 (Inside US)
+1-954-255-2610 (Outside US)
Europe/Mid-East Distributor Operations
Contact local distributor or call +44 118 945 7360
For the latest version of this guide go to: http://www.symbol.com/manuals.
Laser Labels
In accordance with Clause 5, IEC 825 and EN60825, the following 
information is provided to the user:
ENGLISH  HEBREW
CLASS 1  CLASS 1 LASER PRODUCT
CLASS 2  LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
DANISH / DANSK  ITALIAN / ITALIANO
KLASSE 1 KLASSE 1 LASERPRODUKT  CLASSE 1 PRODOTTO AL LASER DI CLASSE 1
KLASSE 2 LASERLYF CLASSE 2 LUCE LASER
SE IKKE IND I STRÅLEN  NON FISSARE IL RAGGIOPRODOTTO
KLASSE 2 LASERPRODUKT  AL LASER DI CLASSE 2
DUTCH / NEDERLANDS NORWEGIAN / NORSK
KLASSE 1 KLASSE-1 LASERPRODUKT KLASSE 1 LASERPRODUKT, KLASSE 1
KLASSE 2 LASERLICHT KLASSE 2 LASERLYS IKKE STIRR INN ILYSSTRÅLEN
NIET IN STRAAL STAREN LASERPRODUKT, KLASSE 2
KLASSE-2 LASERPRODUKT
FINNISH / SUOMI PORTUGUESE / PORTUGUÊS
LUOKKA 1 LUOKKA 1 LASERTUOTE CLASSE 1 PRODUTO LASER DA CLASSE 1
LUOKKA 2 LASERVALO CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
ÄLÄ TUIJOTA SÄDETTÄ PRODUTO LASER DA CLASSE 2
LUOKKA 2 LASERTUOTE
FRENCH / FRANÇAIS SPANISH / ESPAÑOL
CLASSE 1 PRODUIT LASER DE CLASSE 1 CLASE 1 PRODUCTO LASER DE LA CLASE 1
CLASSE 2 LUMIERE LASER CLASE 2 LUZ LASER
  NE PAS REGARDER LE RAYON FIXEMENT NO MIRE FIJAMENTE EL HAZ
PRODUIT LASER DE CLASSE 2 PRODUCTO LASER DE LA CLASE 2
GERMAN / DEUTCH SWEDISH / SVENSKA
KLASSE 1 LASERPRODUKT DER KLASSE 1 KLASS 1 LASERPRODUKT KLASS 1
KLASSE 2 LASERSTRAHLEN KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLEN
NICHT DIREKT IN DEN LASERSTRAHL LASERPRODUKT KLASS 2
  SCHAUEN
LASERPRODUKT DER KLASSE 2
JAPANESE / 日本語
第1種  第1種レーザー製品
第2種 レーザー光線
 光線を見つめないでください
2種 レーザー製品
Laser Devices
Symbol products using lasers comply with US 21CFR1040.10, and 
IEC825-1:1993, EN60825-1:1994+A11:1996. The laser classification is 
marked on one of the labels on the product.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
LASER LIGHT- DO NOT STARE INTO BEAM . CLASS 2
LASER PRODUCT. LASERLICHT -
NICHT IN DEN
STRAHL BLICKEN. LASER KLASSE 2. LUMIÈRE
LASER - NE PAS
REGARDER DANS LE FAISCEAU.
APPAREIL À LASER DE CLASSE 2 630-680nm, 1mW
CAUTION - CLASS 3R LASER LIGHT WHEN OPEN. AVOID DIRECT
EYE EXPOSURE LUMIÈRE LASER EN CAS D'OUVERTURE DE
CLASSE 3R. EXPOSITION DANGEREUSE AU FAISCEAU. KLASSE
3R, VORSICHT - LASERLICHT, WENN ABDECKUNG GEÖFFNET.
NICHT DEM STRAHL AUSSETZEN. SEE QUICK REFERENCE
GUIDE FOR PATENT INFORMATION.
COMPLIES WITH 21CFR1040.10 AND 1040.11
EXCEPT FOR DEVIATIONS
PURSUANT TO LASER NOTICE No. 50, DATED JULY 26, 2001, AND
IEC 60825-1:1993 + A2:2001,EN60825-1:1994+A11:1996+A2:2001.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-103. CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST
CONFORME À LA NORME NMB-003 DU CANADA.
AVOID EXTREME
WRIST ANGLES
AVOID REACHING
AVOID BENDING
CHINESE / 简体中文
1 类 1 类激光产品
2 类 激光切勿注视光束
 2 类激光产品

Navigation menu