Symbol Technologies WWC1002SW86S1 2400 MHz Wireless Printer User Manual addendum to operator manual

Download:
Mirror Download [FCC.gov]
Document ID	27407
Application ID	Dz7/F4Hso9WWqOZSqQOm+A==
Document Description	addendum to operator manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.9kB (11289 bits)
Date Submitted	1999-03-15 00:00:00
Date Available	1999-05-05 00:00:00
Creation Date	2001-07-02 15:56:06
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-07-02 15:56:06
Document Title	addendum to operator manual

Regulatory Addendum
Radio Frequency Interference Requirements
This device has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the Federal Communications Rules and Regulation. These
limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
However, there is no guarantee that interference will not occur in a particular installation.
If the equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try and
correct the interference by one of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC Part 15. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired
operation.”
Radio Frequency Interference Requirements- Canada
This device complies with RSS 210 of Industry & Science Canada. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.”
This Class A digital apparatus meets the requirements of the Industry Canada Standard
ICES-003.
Cet appareil numerique de la Classe A est conforme a la norme NMB-003 du Canada.
CE Marking and European Union Compliance
Products intended for sale within the European Union are marked with the CE
Mark which indicates compliance to applicable Directives and European
Normes (EN), as follows, Amendments to these Directives or ENs are
included:
Applicable Directives
• Electromagnetic Compatibility Directive 89/336/EEC
• Low Voltage Directive 73/23/EEC
Applicable Standards
• EN 55022-Limits and Methods of Measurement of Radio Interference Characteristics
of Information technology Equipment
• EN 50 082-1:1997-Electromagnetic Compatibility-Generic Immunity Standard,
Part 1: Residential, commercial, Light Industry.
• IEC 1000-4-2(1995-01)-Electromagnetic Compatibility (EMC) – Part 4: Testing and
measurement techniques-Section 2: Electrostatic Discharge immunity test.
• IEC 1000-4-3(1995-03)-Electromagnetic Compatibility (EMC) –Part 4: Testing and
measurement techniques-Section 3: Radiated, radio-frequency electromagnetic field
immunity test.
• IEC 1000-4-4(1995-01)-Electromagnetic Compatibility (EMC) –Part 4: Testing and
measurement techniques-Section 4: Electrical Fast transient /burst immunity test.
• EN 60 950+Amd1 + Amd @-Safety of Information Technology Equipment Including
Electrical Business Equipment
• EN 60 825-1 (EN 60 825)- Safety of Devices Containing Lasers
Laser Devices
Symbol products using lasers comply with US 21 CFR1040.10, Subchapter J and IEC
825/EN 60 825 (or IEC 825-1/EN 60 825-1, depending on the date of manufacture). The
laser classification is marked on one of the labels on the product.
Class 1 Laser devices are not considered hazardous when used for their intended
purpose. The following statement is required to comply with US and international
regulations:
Caution: Use of controls, adjustments or performance of procedures other than those
specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power visible light diode. As with any very bright light
source such as the sun, the user should avoid staring directly into the light beam.
Momentary exposure to a Class 2 laser is not known to be harmful.
RF Devices
Symbol’s RF products are designed to be compliant with the rules and regulations in the
locations into which they are sold and will be labeled as required. The majority of
Symbol’s RF devices are type approved and do not require the user to obtain license or
authorization before using the equipment. Any changes or modifications to Symbol
Technologies equipment not expressly approved by Symbol Technologies could void the
user’s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:07:02 15:56:06
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:07:02 15:56:06+01:00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools