Syncomm Technology IA9Q5S83F RF 5G Wireless Module User Manual

Syncomm Technology Corp. RF 5G Wireless Module

Users manual

1 User Manual IA9Q5 S83F RF 5G Wireless Module
2 1. Appearance & Dimension  Dimension：35 * 35 * 0.8 mm  Mechanical Drawing：
32. Mechanical & Key Connector 2.1 PCB Board Material Type：FR-4，Surface finish：ENIG，Layers：4。Dimension：35 * 35 * 0.8 mm; 2.2 FFC Connector
43. Performance 3.1 RF Specification Standard Wireless 5G Proprietary Protocol Connector Type FPC connector 26 Pin 1T1R Modulation GFSK Frequency range 5.165 ~ 5.200 GHz (option) 5.740 ~ 5.840 GHz Output Power 12dBm (Peak power at Antenna port ) Sensitivity -90dBm(The smaller, the better) Input Voltage 3.0~3.6V (3.3V TYP.) Power consumption Consumption Current (TX_MODE):100 mA Consumption Current (RX_MODE):65 mA Antenna Type Dual PCB Routing on board Transceiver mode
53.2 Antenna Specification Impedance Input impedance 50 ohm Frequency 5.135GHz~5.205GHz，5.740~5.840GHz VSWR 5.135GHz~5.205GHz , 1.46 ; 5.740~5.840GHz , 2.02 R.L 5.135GHz~5.205GHz：RL≤-14.5dB，5.15~5.85GHz：RL≤-9.4dB Isolation ANT0 VS ANT1 ≤-15dB The antennas didn’t operate simultaneous. Gain Omni-direction，Peak Gain ≤ 2.85dBi 3.4 GPIO Pin define
64 Reliability Test NO Test Item Test condition Test result 1 TCT (Operating) a) Power on b) Vin = working voltage c) -10℃ to 60℃ d) Duration of exposure –10℃ & 60℃ at least 5mins. e) Ramp rate 2.3 ℃/mins or less. f) Power on/off 2,000 times (applicable to new module project with EEPROM or ECN related to EEPROM.) g) 30 cycles, samples: 6pcs Pass 2 LTST (Operating) a) Power on. b) Vin = working voltage c) Operation at –10℃. d) 72hrs, samples: 6pcs Pass 3 HTST (Operating) a) Power on. b) Vin = working voltage c) Operation at 60℃. d) 72hrs, samples: 6pcs Pass 4 THB (Operating) a) Power on. b) Vin = working voltage c) Operation at 40℃/90%RH~95%RH. d) 72hrs, samples: 6pcs Pass 5 HTOL (Operating) a) Just Power on Module，No Pairing with RXb) Vin = working voltage c) Operation at 85℃ d) 96hrs, samples:50pcs Pass 6 TST (Storage) a) No DC input to Module b) -10℃ to 60℃, Ramp rate 5℃/mins or less c) Duration of exposure at least 5mins. d) 30 cycles, samples: 22pcs Pass 7 LTST (Storage) a) No DC input to Module b) Storage Temp: -20℃ c) 300hrs, samples: 22pcs Pass 8 HTST (Storage) a) No DC input to Module b) Storage Temp: +85℃ c) 300hrs, samples: 22pcs Pass
79 THT a) No DC input to Module b) 40℃, 90%RH~95%RH c) 72hrs, samples: 22pcs Pass 10 Packing VIBRATION a) Sinusoidal, 3g, 5~500Hz, 1hrs/axis b) Random, 3g, 5~500Hz, 0.5hrs/axis c) Number of cycles：3 cycles for each axis d) Vibration axis：X, Y and Z e) samples:6pcs Pass 11 Packing Drop Test a) Height: 92cm (or more) dropped, 1corner, 3 edges, 6 faces. (Total: 10 drops) b) Samples: 6pcs Pass
85. Features a. 5.2GHz/5.8GHz ISM Band b. GFSK modulation c. Low BOM cost d. Long distance > 30m (Line of sight) e. Support 1-1 duplex mode or 1-N broadcasting mode f. RF frequency hopping in 58 channels g. Digital I2S audio interface h. Support no audio detection function i. Audio format 24bit , 32/44.1/48KHz sampling rate j. Robust Packet error correction k. Low power consumption l. No RF induced audio noise m. Compatible with FCC/ CE regulations 6. Application a. Wireless HTiB Rear Speaker b. Wireless Outdoor Speaker c. Wireless TV theater d. Wireless Audio Sender e. Wireless Headphone & Wireless Stereo Ear Microphone
97. Statement a. CE Statement Herby, Syncomm Technology Corp. declares that this RF 5G Wireless Module ，IA9Q5 S83F is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. 1.) Operation limit：Use the RF 5G Wireless Module in the environment with the temperature between 0℃ and 55℃(Temp.), 2.) Operation Frequency range: 5740MHz-5840 MHz 5740MHz-5840 MHz can be used can be used in Europe without restriction. 3.) RF Output Power: 9.81dBm  MANUFACTURER INFORMATION: Manufacturer：Syncomm Technology Corp. Address：10F., No.101, Sec.2 Gongdao 5th Rd., Hsinchu City, 30070 Taiwan Tel: 886-3-5169188 Fax: 886-3-5169111 E-mail: cf.liu@syncomm.com.tw b. FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu