Sysgration NCS50DC NCS50 Display Commander User Manual
Sysgration Ltd. NCS50 Display Commander Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3467259 |
| Application ID | dL2S2+3qLLmSy/sVQABvOg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 146.8kB (1834976 bits) |
| Date Submitted | 2017-07-17 00:00:00 |
| Date Available | 2017-07-18 00:00:00 |
| Creation Date | 2017-07-06 09:47:44 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2017-07-06 09:47:53 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
™ RV CONTROL AND MONITORING SYSTEM Installation and Operation Manual Patent # 9,679,644 Important Safety Information Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could result in personal injury, including death. Do not operate while vehicle is being driven. The Mobile Application, Display Commander and/or Body Control Module should not be used while the vehicle is being driven. Use of the Mobile Application, Display Commander and/or Body Control Module while the vehicle is being driven is dangerous and may cause personal injury or property damage. For adult use only. The Mobile Application, Display Commander and Body Control Module are intended for adult use only, and are not to be used by persons under the age of 18. Use by children may cause personal injury or property damage. Operate only when you have a clear line of sight. Do not operate any moving parts (including, but not limited to, awnings, jacks and slides), unless you have a clear line of sight to the moving part. The Mobile Application, Display Commander or Body Control Module may be used only if you are giving instructions to, and receiving instructions from, another person at least age 18 or older who can clearly see the moving part. Failure to follow these instructions may result in serious personal injury or property damage. Do not operate under the influence of alcohol or drugs. Do not operate the Mobile Application, Display Commander or Body Control Module while under the influence of alcohol or drugs. Doing so may result in personal injury or property damage. Avoid moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. Use recommended accessories. To reduce the risk of fire or electric shock and annoying interference, use only the recommended accessories. • TABLE OF CONTENTS TABLE OF CONTENTS �����������������������������������������������������������3 INTRODUCTION ���������������������������������������������������������������������4 Thank You!�����������������������������������������������������������������������������4 Features���������������������������������������������������������������������������������4 Precautions����������������������������������������������������������������������������4 Packing List����������������������������������������������������������������������������4 INSTALLATION ������������������������������������������������������������������������5 Tools and Supplies�����������������������������������������������������������������5 Disconnecting the Battery������������������������������������������������������5 Selecting the Mounting Location��������������������������������������������5 Mounting the Display Commander (DC)��������������������������������5 Mounting the Switch Plate (SP)���������������������������������������������5 WIRING �����������������������������������������������������������������������������������6 APP SETUP MENU LIST ��������������������������������������������������������7 TRAVEL LOCKOUT (SAFETY) ����������������������������������������������8 TROUBLE SHOOTING �����������������������������������������������������������9 SWITCH PLATE BUTTONS ��������������������������������������������������10 DISPLAY COMMANDER BUTTONS �������������������������������������10 SPECIFICATIONS ����������������������������������������������������������������� 11 Federal Communications Commission (FCC) Statement ������ 11 MOBILE DEVICES: ���������������������������������������������������������������12 Pairing Mobile Device to DC/SP ��������������������������������������������13 NCS50DC/SP FIRMWARE UPDATE* �����������������������������������15 EDIT AND RESET FLOOR PLAN �����������������������������������������16 • INTRODUCTION • Thank You! Thank you for choosing iN-Command. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new iN-Command Lite for maximum enjoyment. • Features Features of iN-Command Lite system: • Simultaneous control by one Android Device or one iOS Device • Control one Light zone • Control Awning • Control Electric Slides • Control Jacks (non-automatic function) • Monitor Battery Voltage with Low Voltage Alert • Packing List (1) Cover, (1) Thumb Screws (1) Body Control Module (BCM) • Precautions • Use the Proper Power Supply. This product is designed to operate with a 12 volt DC, negative ground battery system (the standard system in a North American vehicle). • Use Authorized Service Centers. Do not attempt to disassemble or adjust this precision product; contact a professional for assistance. • Avoid Moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. • Avoid Cleaning Products. The front of this unit should only be cleaned with a slightly damp cloth. Do not use cleaning products. • Use Recommended Accessories. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. (1) Display Commander (DC) (1) Switch Plate (SP) • Mounting the Display Commander (DC) • INSTALLATION • Cut/Drill hole, allowing space below for future programming and behind for ventilation • Route wires through the hole and connect • Attach rear plate with screws • Check and ensure correct operation • Snap main unit into plate • Mount the unit using two #8 PH (0.164” x 0.5”) screws It’s a good idea to read all of the instructions before beginning the installation. We recommend having your iN-Command system installed by a reputable RV dealership • Tools and Supplies You will need the following: • Phillips screwdriver • #2 square drive bit • Wire cutters and strippers • Electrical tape • Volt meter/test light • Crimping tool • Fork Crimp connectors • 10 gauge wire for power and slide connections • 14 and 18 gauge wire for all other connections • Two #8 PH (0.164” x 0.5”) screws for the DC • Two #8 PH (0.164” x 0.5”) screws for the SP • Six #8 PH (0.164” x 1.0”) screws for the BCM • Minimum of 24 gauge wire required to Connect DC To BCM Wall For Reference HOLE SIZES Display Commander (DC) 0.75” Recommended Cutout • Mounting the Switch Plate (SP) • Disconnecting the Battery To prevent a short circuit, be sure to turn off 12V power and remove the negative (-) battery cable prior to installation. • Selecting the Mounting Location Select a mounting location, taking care to avoid the following: • Places exposed to heat-radiating appliances such as electric heaters • Adjacent to other equipment that radiates heat • Under thermostats • Poorly-ventilated or dusty places • Moist or humid locations • Cut/Drill hole, allowing space below for future programming and behind for ventilation • Route wires through the hole and connect • Check and ensure correct operation • Mount the unit using two #8 PH (0.164” x 0.5”) screws Wall For Reference HOLE SIZES Switch Plate (SP) 1.875” Recommended Cutout • WIRING The wiring diagram depicts all the wiring connections required for proper operation of the unit. The TX (transmit) and RX (receive) connections at each device are crossed (crossover cable). BODY CONTROL MODULE (BCM) CONNECTIONS PIN NO. WIRE GAUGE PIN NO. WIRE GAUGE 10 AWG DESCRIPTION M1 OUT 12V (12V FOR M1 EXTEND) 21 10 AWG MOTOR 7 12V OUT 30 AMP (M7 OUT) 10 AWG M1 IN 12V (12V FOR M1 RETRACT) 22 10 AWG MOTOR 6 GND OUT 10 AWG M2 OUT 12V (12V FOR M2 EXTEND) 23 10 AWG MOTOR 6 12V OUT 30 AMP (M6 OUT) 10 AWG M2 IN 12V (12V FOR M2 RETRACT) 24 10 AWG MOTOR 5 GND OUT 10 AWG M3 OUT 12V (12V FOR M3 EXTEND) 25 10 AWG MOTOR 5 12V OUT 30 AMP (M5 OUT) 10 AWG M3 IN 12V (12V FOR M3 RETRACT) 26 10 AWG MOTOR 4 GND OUT 10 AWG M4 OUT 12V (12V FOR M4 EXTEND) 27 10 AWG MOTOR 4 12V OUT 30 AMP (M4 OUT) 10 AWG M4 IN 12V 28 10 AWG MOTOR 3 GND OUT (12V FOR M4 RETRACT) DESCRIPTION (M6 IN) (M5 IN) (M4 IN) (M3 IN) 10 AWG M5 OUT 12V (12V FOR M5 EXTEND) 29 10 AWG MOTOR 3 12V OUT 30 AMP (M3 OUT) 10 10 AWG M5 IN 12V 30 10 AWG MOTOR 2 GND OUT (12V FOR M5 RETRACT) (M2 IN) 11 10 AWG M6 OUT 12V (12V FOR M6 EXTEND) 31 10AWG MOTOR 2 12V OUT 30 AMP (M2 OUT) 12 10 AWG M6 IN 12V 32 10 AWG MOTOR 1 GND OUT 13 10 AWG M7 OUT 12V (12V FOR M7 EXTEND) 33 10 AWG MOTOR 1 12V OUT 30 AMP (M1 OUT) 14 10 AWG M7 IN 12 V 34 10 AWG CHASSIS GND 15 16 AWG TRAVEL LOCK 12V IN 35 10 AWG MOTOR FEED 12V (IN) 16 14 AWG LIGHT GROUP 12V IN 36 10 AWG BCM 12V (IN) 17 14 AWG LIGHT GROUP GND 37 24 AWG 12V OUT 18 14 AWG LIGHT GROUP 12V OUT 38 24 AWG TX 19 14 AWG LIGHT GROUP SWITCH INPUT 12V 39 24 AWG RX (CONNECT TO DC TX) 20 10 AWG MOTOR 7 GND OUT 40 24 AWG GND OUT (CONNECT TO DC) (12V FOR M6 RETRACT) (12V FOR M7 RETRACT) (M7 IN) (M1 IN) (IN) (CONNECT TO DC) (CONNECT TO DC RX) • APP SETUP MENU LIST One light group and seven motor functions can be added or removed via a downloadable App from Google and Apple stores. Motor functions may include slides, awnings, jacks, or any motor that may be controlled with a momentary switch. Refer to the Wiring Diagram and Terminal List when installing new equipment. ITEM SELECTION Light Group 1 No, Yes Motor 1 No, Yes Motor 2 No, Yes Motor 3 No, Yes Motor 4 No, Yes Motor 5 No, Yes Motor 6 No, Yes Motor 7 No, Yes • TRAVEL LOCKOUT (SAFETY) iN-Command is equipped with a Travel Lockout feature to ensure certain system functions are unavailable during transit. When the Brake on the vehicle is activated, iN-Command will lock out (disable) all motorized functions. If the Switch Plate (SP) is installed, the Travel Lock LED will be solid red. If the DC is installed, Travel Lock text will appear. Mobile devices will display Travel Lockout in Orange text and motor functions will cease to actuate and Disabled will appear on the buttons. The light control will continue to function. To turn the Travel Lock off press the “Travel Lock” button on the Display Commander or Switch Plate inside the RV. Travel Lock on a handheld device app Travel Lock on the Display Commander Travel Lock on the Switch Plate • TROUBLE SHOOTING Symptom Solution Verify the BCM is powered on. Display Commander (DC) will not turn ON Check main fuse in Distribution Panel. Check 12V+ on wire to DC (RED wire). Check Ground wire to DC. Check if the Red power LED is off, No power to the Body Control Module (BCM) Check the fuse in the Distribution Panel. Check 12V+ on wire at pin 36. Check Ground wire at pin 34. Cycle power to the BCM and DC. Ensure the wires to the BCM and DC are connected and there is 12V. Ensure the wires to the BCM and DC are not damaged or pinched. DC screen flashing on and off after installation Ensure the Battery is charged. Cycle power to the BCM and DC. Ensure wires are making contact with pins and 12V+ is present. Light Group is not working. Check 12V+ at Pin 16. Check fuse in the Distribution Panel. Motor functions are not working Check 12V+ at pin 35. Travel Lock is on Ensure 12V+ is removed from Pin 15. Functions not operating from DC or App and App shows 0V Check to ensure RX & TX wires connected properly. If an issue is unable to be resolved using the above methods, contact ASA Electronics Technical Support at 1-877-845-8750 or email them at info@asaelectronics.com • SWITCH PLATE BUTTONS The SP (Switch Plate) has 2 buttons on the front of it. From left to right, they are: • Travel Lock • Bluetooth Pairing The Travel Lock button turns off the Travel Lock function when the light is flashing red. The Bluetooth Pairing button is used to pair and unpair the mobile app to and from the SP. • DISPLAY COMMANDER BUTTONS The DC (Display Commander) has 5 buttons on the front of it. From left to right, they are: • Down • Up • Enter • Light • Travel Lock The Down button navigates down through the Function Menu. The Up button navigates up through the Function Menu. Enter button is used to engage motor functions, pair mobile app, and execute menu commands. The Light button turns on/off the light group with a quick press and release. Press and hold the Light button to turn the display back light on/off. 10 • SPECIFICATIONS • Federal Communications Commission (FCC) Statement NCS50DC (Display Commander) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC Maximum Current Draw . .. . . . . . . . . . . . . . . .. . . .200mA@12VDC Minimum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 9VDC Maximum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . 16VDC NSC50 (Body Control Module) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC Maximum Current Draw . . . . . . . . . . . . . . . . . . . . . . . 1A@12VDC Minimum Operating Voltage .. . . . . . . . . . . . . . . . . . . . . . . . 9VDC Maximum Operating Voltage .. . . . . . . . . . . . . . . . . . . . . . . 16VDC NCS50SP (Switch Plate) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC Maximum Current Draw . . . . . . . . . . . . . . . . . . . 200mA@12VDC Minimum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . 9VDC Maximum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . 16VDC 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. System EPROM Non-Volatile Memory . . .. . . . . . . . . . . . . . . . . . . . . YES Bluetooth Version . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 4.0 BLE General Body Control Module . . . . . . .. . . . . 14.9” (W) x 10.4” (D) x 1.8” (H) Display Commander . . . . . . . . . . . . . 3.8” (W) x 1.2” (D) x 2.1” (H) Switch Plate…….... .. . . . . . . . . . . . . . 3.2” (W) x 1.2” (D) x 2.3” (H) 11 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 3.This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. • MOBILE DEVICES: iN-Command Lite is able to pair to Android and iOS devices via the mobile App. Visit the Google Play and Apple App stores on your mobile device to download and use the iN-Command Lite App. Only One mobile device is able to be paired with iN-Command Lite. 12 • Pairing Mobile Device to DC/SP 1. Open NCS Lite application on device. 3. Press “Select” button to connect the SP or DC. 2. Press the gear cog to enter the settings page. 4. Press device name to connect. 13 5. Remote device will show pairing message. The SP will flash a blue light. The DC will flash " Accept new device on display" Press "ENTER" or "BLUETOOTH PAIRING" button to Pair. 6. If connection is successfully established, setting page will show connected device name and versions. To connect NCS50DC/SP with another device. NCS50SP : Long press“BLUETOOTH PAIRING” button for 7~10 seconds to unpair device. If unpairing is successful, NCS50SP will flash blue light twice. repeat steps 2~7 for connecting another device NCS50DC: In DC Menu, select unpair device and press the enter button. A message of "ARE YOU SURE?" will appear. Press "ENTER" button Again. ON APP: When powering down the App select the box to "Unpair Device" 14 • NCS50DC/SP FIRMWARE UPDATE* 1. Press “Update” button to update NCS50DC/NCS50SP. 2.2 For Android: Wait for Wi-Fi connection, then press start button. 2.1 For iOS: In Wi-Fi Settings, connect to Wi-Fi network shown on app. Password is “1234567890”. 3. For iOS : Once connected to network, go back to app, App will automatically start firmware update. 15 • EDIT AND RESET FLOOR PLAN 4. App will display "Update complete" once firmware is update Press Dismiss button. DC/SP will reboot with new firmware. 1. From the Apps Home Page, press the gear cog at the lower right corner to enter the Settings Page. 5. BCM update: Press update button next to BCM version. BCM update will begin automatically. 2. From the Settings Page, you can "Edit Menu", "Load Default Menu", "Load DC Menu" and "Push Settings to DC Menu". ** DO NOT LEAVE APP ONCE UPDATE HAS STARTED** Update will take 10 minutes. 16 3. To Edit the floor plan, press the Edit button. 5. To add or remove functions, press the box next to the function. 4. In the Edit Menu, you can add or remove functions, reposition function and edit the text for the function. 6. To reposition a function, press and hold the "≡" icon next to the function. Drag to move the function to a new location. The "Light" function is shown as an example. 17 7. To edit the text, press on the function text. A device rename window will open. Press "OK" after completing text editing. (The text box is Limited to 12 characters) 8. Once changes have been made, press the Save button at the top of the page. 9. After the floor plan has been edited, the new floor plan settings can be pushed to the DC/SP. Press "Set" Push Settings to DC Menu". 10. After the new floor plan settings have been pushed to the DC/SP, another device can retrieve edited floor plan by pressing the "Load" button next to "Load DC Menu". 11. To go back to the default floor plan settings, press the "Load" button next to " Load Default Menu ". 18 www.jensenrvdirect.com ©2015 ASA Electronics LLC. MA-1612004A-1R
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2017:07:06 09:47:44+08:00 Metadata Date : 2017:07:06 09:47:53+08:00 Modify Date : 2017:07:06 09:47:53+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:24eab31f-c765-462a-99eb-e315c65f9ddd Original Document ID : xmp.did:FA17C261131EE5118A5889141656E9A5 Document ID : xmp.id:8142D800ED61E711A080E21A67A41CFE Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:7F42D800ED61E711A080E21A67A41CFE Derived From Document ID : xmp.did:EF274D65EA61E711A080E21A67A41CFE Derived From Original Document ID: xmp.did:FA17C261131EE5118A5889141656E9A5 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2017:07:06 09:47:44+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 20 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools