Sysgration NCSP35DC NCSP35 Display Commander User Manual
Sysgration Ltd. NCSP35 Display Commander
User manual
™ NCSP35 RV CONTROL AND MONITORING SYSTEM Installation and Operation Manual Patent # US 9,679,735 NCSP35 Important Safety Information Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could result in personal injury, including death. Do not operate while vehicle is being driven. The Mobile Application, Display Commander and/or Body Control Module should not be used while the vehicle is being driven. Use of the Mobile Application, Display Commander and/or Body Control Module while the vehicle is being driven is dangerous and may cause personal injury or property damage. For adult use only. The Mobile Application, Display Commander and Body Control Module are intended for adult use only, and are not to be used by persons under the age of 18. Use by children may cause personal injury or property damage. Operate only when you have a clear line of sight. Do not operate any moving parts (including, but not limited to, awnings, jacks and slides), unless you have a clear line of sight to the moving part. The Mobile Application, Display Commander or Body Control Module may be used only if you are giving instructions to, and receiving instructions from, another person at least age 18 or older who can clearly see the moving part. Failure to follow these instructions may result in serious personal injury or property damage. Do not operate under the influence of alcohol or drugs. Do not operate the Mobile Application, Display Commander or Body Control Module while under the influence of alcohol or drugs. Doing so may result in personal injury or property damage. Avoid moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. Use recommended accessories. To reduce the risk of fire or electric shock and annoying interference, use only the recommended accessories. NCSP35 • TABLE OF CONTENTS CHECKING ACTIVE BLUETOOTH SESSION ������������������������������������ 23 HVAC ���������������������������������������������������������������������������������������������������� 24 Vent Fans�������������������������������������������������������������������������������������������� 24 Fan Only Mode������������������������������������������������������������������������������������ 24 AC Cooling������������������������������������������������������������������������������������������ 24 Heating������������������������������������������������������������������������������������������������ 25 Auto����������������������������������������������������������������������������������������������������� 25 HVAC Schedule���������������������������������������������������������������������������������� 26 SOFTWARE UPDATE* ������������������������������������������������������������������������� 27 RESET: FLOOR PLAN ������������������������������������������������������������������������� 30 TOUCH SCREEN CALIBRATION �������������������������������������������������������� 31 SYSTEM CALIBRATION* ��������������������������������������������������������������������� 32 TROUBLESHOOTING ������������������������������������������������������������������������� 34 INTRODUCTION ���������������������������������������������������������������������4 Thank You!�����������������������������������������������������������������������������4 Features���������������������������������������������������������������������������������4 Precautions����������������������������������������������������������������������������4 Packing List����������������������������������������������������������������������������4 INSTALLATION ������������������������������������������������������������������������5 Tools and Supplies�����������������������������������������������������������������5 Disconnecting the battery�������������������������������������������������������5 Selecting the Mounting Location��������������������������������������������5 Mounting the Display Commander (DC)��������������������������������5 WIRING �����������������������������������������������������������������������������������6 BCM AND DC WIRING DIAGRAM ������������������������������������������7 SETUP MENU LIST �����������������������������������������������������������������8 TRAVEL LOCKOUT (Safety) ���������������������������������������������������9 OVERRIDE SWITCHES* ������������������������������������������������������10 DISPLAY COMMANDER BUTTONS �������������������������������������10 SPECIFICATIONS ����������������������������������������������������������������� 11 FCC NOTES �������������������������������������������������������������������������� 11 PASSCODE PROTECTION ��������������������������������������������������12 SETTINGS �����������������������������������������������������������������������������12 Text Editing*�������������������������������������������������������������������������12 Scroll List Editing������������������������������������������������������������������14 Slides�����������������������������������������������������������������������������������15 Awning���������������������������������������������������������������������������������15 Alarm Inputs�������������������������������������������������������������������������15 Passcode�����������������������������������������������������������������������������16 Set Passcode Timer����������������������������������������������������������17 Change Passcode�������������������������������������������������������������17 Clear Passcode�����������������������������������������������������������������17 MOBILE DEVICES: ���������������������������������������������������������������18 Pairing Mobile Device to DC������������������������������������������������19 NCSP35 • INTRODUCTION • Thank You! • Use Recommended Accessories. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. • Features • Packing List Thank you for choosing iN-Command. We hope you will find the instruc tions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new NCSP35 for maximum enjoyment. Features of iN-Command system include: • Simultaneous control by up to three Android Devices and one iOS Device • Control two zones of Interior Lighting • Monitor all water tank levels • Control and monitor the Water Heater (switches between LP or AC) • Control and monitor the Water Pump • Control Awning • Control Electric Slides • Control Jacks (non-automatic function) • Monitor Battery Voltage with Low Voltage Alert • HVAC (1) Cover, (1) Thumb Screws • Precautions • Use the Proper Power Supply. This product is designed to operate with a 12 volt DC, negative ground battery system (the standard system in a North American vehicle). • Use Authorized Service Centers. Do not attempt to disassemble or adjust this precision product; contact a professional for assistance. • Avoid Moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. • Avoid Cleaning Products. The front of this unit should only be cleaned with a slightly damp cloth. Do not use cleaning products. (1) Display Commander (DC) (1) Body Control Module (BCM) NCSP35 • INSTALLATION • Mounting the Display Commander (DC) It’s a good idea to read all of the instructions before beginning the installation. We recommend having your NCSP35 installed by a reputable RV dealership • Use the mounting hole diagram to measure and cut a mounting hole, allowing space below for future programming and behind for ventilation • Route power and transmit wires through the hole and connect • Check and ensure correct operation • Mount the unit using four #8 PH (0.164” x 0.75”) screws • Attach Trim ring • Tools and Supplies You will need these tools and supplies to install your NCSP35 : • Phillips screwdriver • #2 square drive bit • Wire cutters and strippers • Electrical tape • Volt meter/test light • Crimping tool • Fork Crimp connectors • Minimum of 24 gauge wire required to connect DC to BCM • 10 gauge wire for power and slide connections • 14 and 18 gauge wire for all other connections • Four #8 PH (0.164” x 0.75”) screws for the DC • Six #8 PH (0.164” x 1.0”) screws for the BCM CUTOUT FOR DISPLAY COMMANDER (DC) RECOMMENDED CUTOUT WALL FOR REFERENCE CUTOUT 3.0" • Disconnecting the battery To prevent a short circuit, be sure to turn off 12V power and remove the negative (-) battery cable prior to installation. 4.3" • Selecting the Mounting Location Select a mounting location, taking care to avoid the following: • Places exposed to heat-radiating appliances such as electric heaters • Adjacent to other equipment that radiates heat • Under thermostats • Poorly-ventilated or dusty places • Moist or humid locations NOTE: Before cutting the mounting hole, make sure the area behind the mounting location is clear of wires, fuel and vacuum or water lines; ensure there is at least a 2.75”clearance below the Display Commander to allow for programming by USB stick. NCSP35 • WIRING The Wiring Diagram Depicts All The Wiring Connections Required For Proper Operation Of The Unit. Body Control Module (BCM) Connections FRESH 1 TANK IN (BROWN) -1 CAN LOW - 48 48 50 50- NC FRESH 2 TANK IN (RED) - 2 GND - 52 CAN HIGH - 47 47 49 49- NC BLACK 1 TANK IN (ORANGE) - 3 52 +12VDC OUT - 51 51 CAN LOW - 44 BLACK 2 TANK IN (YELLOW) - 4 44 46 43 45 GREY 1 TANK IN (GREEN) - 5 GREY 2 TANK IN (BLUE) - 6 GREY 3 TANK IN (PURPLE) - 7 TANK LEVEL COMMON 7VDC (GRAY) - 8 CAN HIGH - 43 DETAIL D 46- NC 45- NC DETAIL C DETAIL A 42 LIGHT GROUP 1 SWITCH INPUT 12V - 9 LIGHT 12V 15A IN - 10 LIGHT GROUP1 GND - 11 LIGHT GROUP1 12V 15A OUT - 12 LIGHT GROUP 2 SWITCH INPUT 12V - 13 LIGHT GROUP2 GND - 14 LIGHT GROUP2 12V 15A OUT - 15 AWNING SWITCH INPUT 12V - 16 GND - 17 AWNING LIGHT 12V 5A OUT - 18 AWNING LIGHT GND -19 41 40 39 10 38 11 37 12 36 13 35 14 34 15 33 16 32 17 TRAVEL LOCK IN 12V (BROWN) - 20 20 31 18 30 19 29 WATER HEATER GND (RED) - 21 21 28 WATER HEATER GAS +12V 1A OUT (ORANGE) - 22 22 27 WATER HEATER ELECTRIC +12V 1A OUT (YELLOW) - 23 23 26 +12V WATER HEATER FAULT IN (GREEN) - 24 24 25 DETAIL B 42 41 40 39 +12VDC IN POWER HOUSE +12VDC IN POWER CHASSIS 12V IN 30 AMP SLIDE & JACK POWER GROUND IN 38 37 36 35 34 33 32 31 30 29 12V OUT 30 AMP (SLIDE#1) GND OUT (SLIDE#1) 12V OUT 30 AMP (SLIDE#2) GND OUT (SLIDE#2) 12V OUT 30 AMP (SLIDE#3) GND OUT (SLIDE#3) 12V OUT 30 AMP (SLIDE#4) GND OUT (SLIDE#4) 12V OUT 30 AMP (SLIDE#5) GND OUT (SLIDE#5) 28 27 26 25 WATER PUMP +12V IN 10A WATER PUMP GND WATER PUMP +12V OUT 10A GND NCSP35 • BCM AND DC WIRING DIAGRAM NCSP35 • SETUP MENU LIST Tanks, light groups, and motor functions can be added or removed. Motor functions may include slides, awnings, jacks, or any motor that may be controlled with a momentary switch. Refer to the Wiring Diagram and Terminal List when installing new equipment. The BCM may not include relays for non-OEM functions. Basic automotive 1505 relays (12VDC Coil, 40/30A 14VDC Contact) can be purchased for installation and repair. HVAC (Zone1, Zone2, Zone3) Mode On, Off, Fan, Cool, Heat, Auto Vent Open, Shut Vent Fan Off, Low, Medium, High Schedule Start time, Stop time Inverter Slides Slide 1 Slide 2 Slide 3 Slide 4 Slide 5 In, Out In, Out In, Out In, Out In, Out Lights Light Group 1 Light Group 2 Awing Light Dimmer Light 1 Dimmer Light 2 Dimmer Light 3 No, Yes No, Yes No, Yes No, Yes No, Yes No, Yes Settings Bluetooth Wi-Fi Date & time Edit Passcode Brightness Calibration System Reset Information Software Administration Scan On, Off, Scan, Add Edit Setting Up, Down Set Floor Plan , Factory Information notes DC/App/BCM Updat Awings Awning Light Awning 1 Awning 2 No, Yes In, Out In, Out NCSP35 • TRAVEL LOCKOUT (Safety) iN-Command is equipped with a Safety Lockout feature to ensure certain system functions are unavailable during transit. When the Brake Signal (Towable) or Ignition (Motorized) is activated, the iN-Command will lock down all motorized functions. The Display Commander (DC) and mobile devices will also display “Travel Lock Engaged” and the affected buttons will cease to activate. The lights, water pump, water heater, and sensors will continue to function. To turn the Travel Lock off, press "DISENGAGE" on the Display Commander (DC), inside the RV, once the brake signal has been removed. Travel Lock on the Display Commander NCSP35 • OVERRIDE SWITCHES* • DISPLAY COMMANDER BUTTONS The Body Control Module has an override switch and knob. The knob below the switch corresponds to a motor function made by the Display Commander and Handheld Devices App. The switch and knob actuate all the motor functions on the RV. The DC (Display Commander) has 4 buttons on the front of it. From left to right, they are: • Power • Settings • Home • Return To use the override switches, locate the switch on the BCM. Turn the knob underneath the switch to select the component. Press up or down on the switch. The switch is momentary and will activate the component only while pressed in either direction. The Power Button turns the DC on and off (long press) and revives it (short press). The settings button takes you to the settings page. The Home Button returns you to the Home page. The Return Button returns you to the previous page. Power 10 Settings Home Return NCSP35 • SPECIFICATIONS • FCC NOTES Display Commander (DC) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC Maximum Current Draw . . . . . . . . . . . . . . . . . . . . . 1.5A@9VDC Minimum Operating Voltage . . . . . . . . . . . . . . .. . . . . . . . 9VDC Maximum Operating Voltage . . . . . . . . . . . . . . . . . . . . . 16VDC WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Body Control Module (BCM) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC Maximum Current Draw . . . . . . . . . . . . . . . . . . . . 4A@12VDC Minimum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . 9VDC Maximum Operating Voltage . . . . . . . . . . . . . . . . . . . . . 16VDC IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. NCSP35 System EPROM Non-Volatile Memory . . . . . . . . . . . . . . . . . . . . . . YES Bluetooth Version . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 4.0 BLE General Body Control Module . . . . . . . . 14.9” (W) x 10.4” (D) x 1.8” (H) Display Commander . .. . . . . . . . . .5.2” (W) x 3.8” (D) x 1.5” (H) This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 11 NCSP35 • PASSCODE PROTECTION • SETTINGS From the Menu screen you can: • Edit iN-Command function text • Reposition functions • Enable/disable functions • See the status of iN-Command • Connect devices with Bluetooth • Change the passcode • Reset the floor plan • View iN-Command’s Legal documents and customer support information. A passcode is required to access the system. On the first time use of the system, the user is required to enter and confirm a new passcode. The Setup button is used by the manufacturer. • Text Editing* 1. Select “Settings” Confirm the new passcode. 12 NCSP35 4. Long press the intended text, e.g., "Light Group 2" 2. Press “Edit” to enter Edit page 5. Use the keyboard to edit the name, then press "Ok" 3. Select the function to edit. Note: Editing the text on the DC will not change the text on a device’s App. 13 NCSP35 • Scroll List Editing 1. Select " Settings" 3. Select the function to edit. 2. Press “Edit” to enter Edit page 4. Use the Up and Down arrows next to the function to move the item in the list. 14 NCSP35 • Slides • Alarm Inputs Slides can added to the system. Note: Desired devices need to be correctly wired to the BCM to function. Alarm can added to the system. Note: Desired devices need to be correctly wired to the BCM to function. • Awning Awning can added to the system. Note: Desired devices need to be correctly wired to the BCM to function. 15 NCSP35 • Passcode 1. Select “Settings”. 2.1 Enter the correct passcode to proceed. 2. Press “ Passcode” to enter passcode setup. 3. The passcode setup window will open. 16 NCSP35 • Set Passcode Timer Press the “Set Timer” select the idle time to activate the passcode protection. 3. Confirm new passcode. • Change Passcode 1. Press the “Change Passcode” button to change to a new passcode. 2. Enter the new passcode • Clear Passcode Press the “Clear Passcode” to clear the passcode. This will restart the App, take the user to the End-User License Agreement, and have the user setup a new passcode. 17 NCSP35 • MOBILE DEVICES: iN-Command is able to pair to Android and iOS devices using the iN-Command App. Visit the Google Play and Apple App stores on your mobile device to download and use the iN-Command App. Seven mobile devices are able to be paired iN-Command at one time, but only 1 iOS and 3 Android devices are able to be actively paired at the same time; meaning, 3 Android devices and 1 iOS device can all actively control the iN-Command functions. To use another device not actively paired to iN-Command, 1 device needs to shut down its iN-Command App to allow another device to actively pair. To do this simply select the power button on the App, shut down the App in the device’s settings menu, or press “DISCONNECT” on the DC’s Connections page. 18 NCSP35 • Pairing Mobile Device to DC 2.1 Select the “ Bluetooth ” tab. 1. Enable "Bluetooth" in the system settings of the mobile device 2. From the DC Home Page, select "Settings" 2.2 Select "Pairing" to pair devices and view current paired devices. 19 NCSP35 2.3 Press Scan to start scanning for Unpaired devices. Locate the mobile device in the Unpaired Device list. Select the device by pressing it. 2.5 A Bluetooth Pairing request will appear on the DC and mobile device. 2.6 Press "PAIR" on the DC. 2.4 A Popup with the device name will apear on the display. Press "PAIR" 2.7 Press "Pair" on the mobile device. 20 NCSP35 2.8 The mobile device will be displayed in the "Paired devices" list on the DC 2.10 The mobile device now shows that the DC is connected. 2.9 The DC will be displayed on the mobile device list in the format " NCSPDCXXXXX". Press the DC on the mobile device to connect with it. 21 NCSP35 4. Reset Floor Plan Press the “Reset” button in the Menu page to load the floor plan configuration from the DC. The current settings will be lost/replaced. 22 NCSP35 • CHECKING ACTIVE BLUETOOTH SESSION 1. Select “Connected devices”. * To disconnect a handheld device, press “DISCONNECT”, or simply shut down the device’s App. This function is used to disconnect a device that is not actively being used, and to allow another device to be connected. 2. The page shows information of current active Bluetooth devices. 23 NCSP35 • HVAC From the HVAC page, you can control the Heating, Ventilation and Air conditioning functions in the RV. With iN-Command, you can control up to 4 HVAC zones and schedule times for the HVAC function to be active. • Vent Fans The Vent Fans for each zone can be opened, closed, and change the fan speed. • AC Cooling 1. Select the desired Zone. Press the "Mode" button to switch to "Cool" mode. 2. Use the "Set" up and down arrows to set the desired temperature for the zone. 3. Press the "Fan" button to switch between Low,High and Auto fan speeds. • Fan Only Mode 1. To have just the AC fan operating in a zone, select the desired Zone, the press the "Mode" button to switch to Fan mode. 2. Press the " Fan" button to switch between Low and High fan speeds. 24 NCSP35 • Auto • Heating Auto Mode will automatically switch between Cool and Heat modes to reach the desired Set temperature. (Heat Mode is only available in Zones with Heat Mode selected on Floor Plan). 1. Select the desired Zone. Press the "Mode" button to switch to "Heat" mode. 2. Press the "Source" button to select between Gas and Electric. (Available Heat sources depend on Floor Plan) 3. Use the "Set" up and down arrows to set the desired temperature for the zone. 1. Select the desired Zone. Press the "Mode" button to switch to "Auto" mode. 4. Press the "Fan" button to switch between Off, Low, High and Auto. (Off is not available in Electric Heat Source.) 2. Use the "Set" up and down arrows to set the desired temperature for zthe zone. 3. Press the "Fan" button to switch between Off, Low, High and Auto. 25 NCSP35 • HVAC Schedule The Schedule function allows you to set a temperature and choose a start and stop for when you want the HVAC function to operate. 1. Press the "Clock" icon at the bottom right corner of the HVAC home screen to enter the Schedule page. 2. Use the "Set" up and down arrows to set the desired temperature. 3. Use the " Start" and "Stop" arrows to set the time frame that you want the HVAC function to operate. 4. Choose schedule 1 or 2 on HVAC zone Home Page. 26 NCSP35 • SOFTWARE UPDATE* Software updates include floorplan redesigns and App version updates. 1. Insert USB drive loaded with updated software into the USB port at he bottom of the DC. 2. Select "Settings" enter the Settings page. 4. In the software page, you can choose to update the Floor Plan, DC Version, App Version and BCM Versions. The system will look for specific file names for software updates. - File name: “NCSP3-DC VXXXX.zip” > DC OS update (xxxx is the version number) - File name: “ncspdcap_vxxxx.apk” > DC App update (xxxx is the version number) - File name: "NCSPDC3Vxxxx.bin" > BCM update (xxxx is the version number) 3. In the Settings page, select the "Software" tab. 27 NCSP35 6. Press the DC Version to update the DC OS sytem. Press "UPDATE" 8. Press "Ok" to continue. 9. Press the BCM Version to update the BCM system. Press "UPDATE" 7. Framework update, Press"Update" 28 NCSP35 12. Press the Floor Plan to select a floor plan. Press "Load" to select the floor plan. 10. Press the App version to update the DC App. Press " UPDATE" 13. Press "DISMISS" to confirem selection. 11. Waiting for Update. 29 * If a software update is needed, go to http://www.asaelectronics.com//in-command ** If there is a software issue, Call ASA Electronics Technical Support at 1-877-845-8750 or email them at info@asaelectronics.com. NCSP35 • RESET: FLOOR PLAN 3. Select on of the two options.(Floor Plan of Factory) to restore to a previous state. Current settings will be lost. a. Floor Plan: restores to previous floor plan settings from RV manufacturer. b. Factory: restores to default settings from ASA electronics. Rest to Floor Plan to remove customization, or reset to factory settings. 1. Select "Settings". 2. Select “System Reset” in the Settings page. 3. Confirm for floor plan to complete update. 30 NCSP35 • TOUCH SCREEN CALIBRATION 1. Select “Settings”. 3. To calibrate the Touch Screen, select "Set". Follow the instructions.The DC will restart after calibration. 2. Select “Calibartion”. 4. Touch the center of the cross. 31 NCSP35 • SYSTEM CALIBRATION* From the admin page, the App Date can be deleted, the Generator Hour Meter can be set, and the Water Tanks can be calibrated. 1. From the Settings page, press "Administration". 3. Make Selection. 2. Select “Calibartion”. 4. Select “Tanks” to set resistor reference value for every tank. 32 NCSP35 * The system is calibrated by the manufacturer and should only be accessed for troubleshooting. 7. Press the Generator Hour Meter "Set" button to set the meter time. ** The Admin Passcode is used by the manufacturer for programming and troubleshooting purposes. Should there be a calibration issue, call ASA Electronics Technical Support at 1-877-845-8750 or email them at info@asaelectronics.com. 8. Press the App Date "Delete" button to clear current App date. Note: This will remove the floor plan settings from the RV Manufacturer. 33 NCSP35 • TROUBLESHOOTING Symptom Display Commander (DC) will not power on or no front panel operation No Power to the Body Control Module (BCM) Solution Check for +12VDC on Positive (+) input on back of the DC. Check for Ground on Negative (-) input on back of the DC. Check fuse in Distribution Panel. Try cycling power with the power button. Check for +12VDC on pin 42. Check for Ground on pin 39. Check fuse in Distribution Panel. Disconnect power wires from the back of the DC. DC screen flashing on and off after installation Shut off all power to the DC and BCM. Reconnect power wires to the DC. Return power to the DC and BCM Press Reset button on the BCM Motor Functions do not activate Check for +12VDC on pin 41. Ensure the relay activates.* *Relay not activating Replace the relay with one from an unused circuit. See label on BCM cover for relay identification DC shows 0V and no functions Check to ensure 4 pin RV-C cable is connected to the back of the DC and to the BCM. activate from DC Check for shorts in RV-C cable and for loose pins in the connection. For additional troubleshooting, call ASA Electronics Technical Support at 1-877-845-8750, email info@asaelectronics.com or visit our website http://www.asaelectronics.com//in-command. 34 NCSP35 NCSP35 www.jensenrvdirect.com ©2015 ASA Electronics LLC. MA-1709002-1R
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2017:11:20 18:16:28+08:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2018:01:18 19:22:48+08:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2018:01:18 19:22:48+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:00da5a39-e075-4e66-8c6e-77b5ca233589 Original Document ID : xmp.did:FA17C261131EE5118A5889141656E9A5 Document ID : xmp.id:9DAF2FD9DBCDE7119929F63B4155609B Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:9CAF2FD9DBCDE7119929F63B4155609B Derived From Document ID : xmp.did:88B1B037C7CDE7119929F63B4155609B Derived From Original Document ID: xmp.did:FA17C261131EE5118A5889141656E9A5 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2017:11:20 18:16:28+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 39EXIF Metadata provided by EXIF.tools