TCL Technoly Electronics 04 BT Module User Manual JS BTM8630 Product User Guide

Download:
Mirror Download [FCC.gov]
Document ID	2178911
Application ID	D+1+zhYpp2pmh0xIcwNWUQ==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.01kB (25088 bits)
Date Submitted	2014-01-28 00:00:00
Date Available	2014-01-28 00:00:00
Creation Date	2014-01-17 09:31:09
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2014-01-17 09:31:09
Document Title	Microsoft Word - JS-BTM8630 Product User Guide.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	User

BTM8630 Product User Guide
BTM8630 is a Bluetooth stereo module which can be used to design Bluetooth
stereo speakers. Besides, B T M 8 6 3 0 can be as a direct connection to any
Bluetooth mobile phone when designed into stereo speakers device.
Interface
- PIO
BTM8630 has a total 8 programmable I/O terminals and 3 LEDs. These
are controlled by firmware running on the device.
Microcontroller
The microcontroller (MCU), interrupt controller and event timer run the
Bluetooth software stack and control the radio and host interfaces. A 16bit reduced instruction set computer (RISC) microcontroller is used for
low power consumption and efficient use of memory.
Audio Interface
The audio interface circuit consists of a audio CODEC, dual audio inputs
and outputs. The CODEC supports playback and recording of audio
signals at multiple sample rates with a resolution of 16-bit.
The ADC and the DAC of the CODEC each contain two independent
channels. Any ADC or DAC channel can be run at its own independent
sample rate.
The audio input circuitry consists of a dual audio input
that can be configured to be either single ended or fully differential and
programmed for line input.
The audio output circuitry consists of a dual differential class A-B
output stage.
Clock Input and Generation
The reference clock for the system is generated from a TCXO or
crystal input 26MHz. All internal reference clocks are generated using
a phase locked loop, which is locked to the external reference
frequency.
BTM8630 Product User Guide
Radio
Common TX/RX terminal simplifies external matching; eliminates
external antenna switch.
BIST minimises production test time. No external trimming is required
in production
Full RF reference designs available
Bluetooth V4.0 Specification compliant
Bluetooth Software Stacks
CSR’s Bluetooth Protocol Stack runs on the on-chip and MCU in a variety
of configurations:
- Standard HCI (UART or USB)
- Fully embedded RFCOMM
- Customised builds with embedded application code
Power
For Class 2 Bluetooth applications, the regulator used to derive 3.3V
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
BTM8630 Product User Guide
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
This device is intended only for OEM integrators under the following conditions:
1. The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2. The transmitter module may not be co-located with any other transmitter or
antenna,
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization
is no longer considered valid and the FCC ID can not be used on the final product.
In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labelling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users.
The final end product must be labelled in a visible area with the following:
“Contains FCC ID: ZVA04”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The Module must be installed in BLU-RAY DISC HOME THEATER SOUND
SYSTEM.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : User
Create Date                     : 2014:01:17 09:31:09+08:00
Modify Date                     : 2014:01:17 09:31:09+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - JS-BTM8630 Product User Guide.doc
Creator                         : User
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:dfa51b03-313c-4548-b8e3-670c12be001e
Instance ID                     : uuid:a7ea3d1d-92a1-40f3-bc24-74ef0e1ca8e6
Page Count                      : 3

EXIF Metadata provided by EXIF.tools