TECNO MOBILE CA7 Mobile phone User Manual Sanjeev

TECNO MOBILE LIMITED Mobile phone Sanjeev

User Manual

1ExplosionExplosion diagramdiagram specificationspecification1CTP+LCM Assembly2Front camera seal foam3Receiver Decoration4Front Housing Assembly5Front camera rubber6Front camera7Receiver8Main PCBA9FPC side key10LCM junctor steel Assembly11Back camera12Card holder13Light sensation rubber14Screw15Battery junctor steel16Fingerchip Assembly17Cam lens18Battery cover Assembly19Speaker20Battery21Cable RF22Jack rubber23MOT FPC24SUB PCBA25Main link fpc26Mic rubber27FPC speaker28USB rubber
2Know your phone1. Front camera2. Volume key3. Power key1
3SIM/SD card installation1. Power off mobile.2. Refer to the following picture for SIM / SD cardinstallation.
4Charging the phoneYou can charge your device using a charger or by connectingit to the computer using a USB cable (comes with thephone).1. Please remind the front and back of the plug.2. Use only TECNO charger and cables. Other chargers orcables may damage the device. This will invalidate yourphone warranty.
FCC CautionLabelling requirements.This device complies with part 15 of the FCC Rules. Operation is subjectto the condition that this device does not cause harmful interference.Information to user.Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.Information to the user.Note: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipmentgenerates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or moreof the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.Specific Absorption Rate (SAR) information:This Mobile phone meets the government's requirements for exposure toradio waves. The guidelines are based on standards that were developedby independent scientific organizations through periodic and thoroughevaluation of scientific studies. The standards include a substantial safetymargin designed to assure the safety of all persons regardless of age orhealth.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is1.6W/kg averaged over one gram of tissue. Device types: CA7FCC ID:2ADYY-CA7) has also been tested against this SAR limit. The highest SARvalue reported under this standard during product certification for use atthe ear is 0.46W/kg and when properly worn on the body is 1.28W/kg.This device was tested for typical body-worn operations with the back ofthe handset kept 10mm from the body. To maintain compliance with FCCRF exposure requirements, use accessories that maintain a 10mmseparation distance between the user's body and the back of the handset.The use of belt clips, holsters and similar accessories should not containmetallic components in its assembly. The use of accessories that does notsatisfy these requirements may not comply with FCC RF exposurerequirements, and should be avoided.Body-worn OperationThis device was tested for typical body-worn operations. To comply withRF exposure requirements, a minimum separation distance of 1.0 cmmust be maintained between the user’s body and the handset, includingthe antenna. Third-party belt-clips, holsters, and similar accessories usedby this device should not contain any metallic components. Body-wornaccessories that do not meet these requirements may not comply with RFexposure requirements and should be avoided. Use only the supplied oran approved antenna.

Navigation menu