TENDA TECHNOLOGY W15E AC1200 Wireless Hotspot Router User Manual W15EV1 0 TDE01

SHENZHEN TENDA TECHNOLOGY CO., LTD. AC1200 Wireless Hotspot Router W15EV1 0 TDE01

Contents

User Manual

FAQIf any item is missing, or damaged, please keep the original package and contact the local reseller or distributor immediately.Before using this router, please read this Installation Guide carefully for proper and quick installation. For detailed product information or more functions, please visit http://www.tendacn.com.2．Connecting to WAN PortFor ADSL scenario, connect the Ethernet cable that has been connected to the ADSL modem to the WAN port of the router.For FTTB scenario, connect the Ethernet cable provided by the ISP to the WAN port of the router.For FTTH scenario, connect the Ethernet cable that has been connected to the optical modem to the WAN port of the router.3. Connecting Computer, Smart Phones or Other ClientsPower receptacleSwitchWireless connectionWired connectionStep 1: Connecting the Router1．Installing RouterWAN1Place the router upside down on the workbench, and paste the four footpad stickers onto the round recesses at the bottom of the router.1Power on the router with the attached power adapter in the package.Connect your computer to one LAN port of the router, or a switch that has been connected to the router with the Ethernet cable. Wireless clients, suchas smart phones, can connect to the Wi-Fi network of the router.12Place the router right side up on the workbench, and adjust the position of the antennas as below.2PadBottomRound recessWAN portPhone cableADSL modemADSLor orFTTB Cable portPacking ListWireless Hotspot Router x 1Power adapter x 1Ethernet cable x 1Pad x 4Installation guide x 1Installation GuideAC1200 Wireless Hotspot RouterModel: W15EorOptical cableFTTH Optical modemLAN portLED IndicatorLED Indicators DescriptionSYSSolid on: The system is faulty; Blinking: The system works properly; Off: The system is not powered on.Solid on: The 2.4 GHz Wi-Fi is enabled without data transmission; Blinking: Data is transmitted over 2.4 GHz; Off: The 2.4 GHz Wi-Fi is disabled.Solid on: The 5 GHz Wi-Fi is enabled without data transmission; Blinking: Data is transmitted over 5 GHz; Off: The 5 GHz Wi-Fi is disabled.WAN port indicatorSolid on: No data is transmitted over WAN port 1.Blinking: Data is transmitted over WAN port 1.Off: No device connects to WAN port 1, or connection is faulty.WAN/LAN port 2/3/4 indicators (By default, thay are LAN port indicators.)Solid on: No data is transmitted.Blinking: Data is transmitted.Off: No device connects to these ports, or connection is faulty.LAN port indicatorSolid on: No data is transmitted over LAN port 5.Blinking: Data is transmitted over LAN port 5.Off: No device connects to LAN port 5, or connection is faulty.5GHz2.4GHz12/3/45SYS 2.4GHz 1 55GHz 2/3 4/Port, and ButtonPort or ButtonReset 1 5DescriptionReset Reset button. After the router is powered on, use a paper clip to hold down the Reset button for 8 seconds to restore the device to factory settings.It is the WAN port used to connect to the internet using Ethernet cable. The Ethernet cable may be a cable connected to the ADSL modem, optical modem, or cable modem, or a cable provided by the ISP.They can be used either as WAN ports or LAN ports. By default, they are LAN ports. You can login to the router web UI to change them to WAN ports.It is the LAN port used to connect to a device such as a computer or switch.2/3/4152/3 4/Q: I cannot login to the web UI of the router after entering www.tendawifi.com or 192.168.0.1. What should I do?A: 1. Ensure that the Ethernet cables are correctly connected. 2. If you connect your computer to the router using Ethernet cable, ensure that the Obtain an IP address automatically of your computer is selected. 3. If you use wireless devices, such as smart phones, to connect to the Wi-Fi, ensure that the wireless devices have been successfully connected to the Wi-Fi. 4. Clear the cache of your web browser or replace the web browser, and try to login again. 5. Use another computer or smart phone and try to login again. 6. Press the Reset button with a paper clip for 8 seconds to restore the device to factory settings, and try to login again.Q: I can scan the SSID, but cannot connect to it. What should I do?A: 1. Verify that the WiFi password is correct. 2. Clear the cache of your wireless clients (such as smart phone and notebook), and try again. 3. Connect your computer to the router using Ethernet cable, and login to the web UI of the router. Change the SSID or Wi-Fi password, and try to reconnect and login again.Q: The Wi-Fi signal is successfully connected, but I still cannot access the internet. What should I do?A: 1. Verify that you connect to the correct SSID. 2. Access the System Info page of the router web UI, and verify that the connection status of corresponding port is Connected.Q: What should I do if I forget the Wi-Fi password?A: 1. Connect your computer to the router using Ethernet cable, and login to the web UI of the router. Choose Wireless > Basic, view or reset the Wi-Fi password. 2. If the above method does not work, power on the router, press the Reset button with a paper clip for 8 seconds to restore the device to factory settings. In this case, you need to reconfigure the internet settings and WiFi password.CE Mark WarningThis is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.The mains plug is used as disconnect device, the disconnect device shall remain readily operable.NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.Declaration of ConformityHereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type W15E is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internetaddress: http://www.tendacn.com/en/service/page/ce.html Operate Frequency: 2400-2483.5MHz; 5150-5250MHzEIRP Power (Max.): 2.4GHz: 19.8dBm; 5.1GHz: 22.5dBmSoftware Version: V15.11.0.5 RECYCLINGThis product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.User has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment. Caution:Adapter Model: BN036-A12012E Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTDInput: 100-240V~, 50/60Hz, 0.4A DC VoltageFCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Radiation Exposure StatementThis equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.Appendix 1: Configure Your Computer (Example: Windows7)Interne t??Network and Internet Network and Sharing Ce nte r Se arc h Con tro l Pan elConn ec t or discon ne ctNo Int er net acces sLoca l Are a Conne ct io nor VPN c on nection ,o r set up a-up, o r VP N network c on necti onwork c om puter,or c ha nge sha ri ngSee fu ll m apCont ro l Panel H om eChan ge a dapte r se tt iChan ge a dvanc ed s hsett in gsSee al soHome Gr oupInte rn et Option s查看基本网络信息并设置连接TD-PCActivityIPv4 Connectivity: N o In terne t ac ce ssNo Int er net acces sEnab led05:52:331.0 GbpsI v6 PConn ectivity:Medi a State:Dura tion:Spee d:Deta ils...Clos eDiag noseSent Recei vedBytes: 41，627，947 6 1,784 ,832Proper ties DisableLocal Area Connection S tat usGene ra lConn ectio nRealtek PCIe GBE Family ControllerNetworkingConnect usingConfigure...QoS Packet SchedulerFile and Printer Sharing for Microsoft NetworksInternet Protocol Version 6(TCP/IPv6)Internet Protocol Version 4(TCP/IPv4)Link-Layer Topology Di scovery Mapper I/0 DriverLink-Layer Topology Di scovery Resp onderLLooccaall AArreeaa CCoonnnneeccttiioonn PPrrooppeerrttiieessOKInstall... Pr opertiesUninstall...CancelThis connection uses the following items:Transmission Control Protocol/Internet Protocol. The defaultwide area network protocol that provides commun ication across diverse interconnected networks.DescriptionCurrently connected to：Unidentified networkNo Internet accessOpen Network and Sharing Center2:30 PM3/21/2014General Alternate ConfigurationYou can get IP settings assigned automatically if your network supports this capability. Otherwise,you need to ask your network administrator forthe appropriate IP settings.Obtain an IP address automaticallyUse the following IP address:Obtain DNS server address automaticallyUse the following DNS server addresses:AdvancedOOKKCancelDefault gateway:Subnet mask:IP address:Preferred DNS server:Alternate DNS server:Validate settings upon exitIInntteerrnneett PPrroottooccooll VVeerrssiioonn 44 ((TTCCPP//IIPPvv44))PPrrooppeerrttiieess2. Click Open Network and Sharing Center;1. Right-click the icon in the lower-right corner of the desktop.1.Click Local Area Connection 2.Click PropertiesFind and double click Internet Protocol Version 4(TCP/IPv4);2.click OKOpen Network and Sharing Center10:32 PM10/5 7/201Click the icon in the lower-right corner of the desktop. 1.Select Obtain an IP address automatically and Obtain DNS server address automatically Not connectedConnections are availableWireless Network ConnectionTenda_XXXXXXConnect automatically ConnectOpen Network and Sharing CenterSelect your wireless network from the list, click Connect and then follow onscreeninstructions.Currently connected to:Tenda_XXXXXXInternetWireless Network ConnectionTenda_XXXXXX ConnectedOpen Network and Sharing CenterConnected successfully!Appendix 2: Example: Connection WiFi ( Windows 8)* Operating temperature: 0 C ~ 40 C; operating humidity: 10%RH ~ 90%RH (non-condensing)Technical SupportUnited States Hotline: 1-800-570-5892 Canada Hotline: 1-888-998-8966 Hong Kong Hotline: 00852-81931998 Skype: TendaszWebsite: http:// www.tendacn.com E-mail: support@tenda.com.cnAddress Info: 6-8 Floor, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052Safety and Emission StatementStep 2: Configuring the Routertendawifi.com 进入Start a browser, enter tendawifi.com or 192.168.0.1, and press Enter.Set your wireless network name and Wi-Fi password, and click Next. Wait a second for the completion of settings. For more functions, visit http://www.tendacn.com to download user guide of the router.Click Start. The system automatically detects your internet connection type. Enter related values according to the on-screen instructions, and click Next.142 3Welcome to Tenda Wireless Hotspot RouterClick Start to configure the internet and wireless settings quickly.StartInternet SettingsSettings completed!You are disconnected. Please reconnect to:Tenda_A0BE70Or Tenda_A0BE70_5GClick More to configure other functions, such as portal authorization and bandwidth control.MoreWireless SettingsPlease set your wireless network name and passwordBy default, the Set the wireless password as login password is enabled. You can also disable this option and customize your login password.By default, the wireless network has no password. You need to reconnect to the Wi-Fi signal once the SSID or WiFi password is changed.By default, the SSID of the 2.4 GHz network is Tenda_XXXXXX (see the label at the bottom of the router), and the SSID of the 5 GHz network is Tenda_XXXXXX_5G.The computer can connect to the Wi-Fi signal only when a wireless adapter is installed and works properly.Please select an internet connection typeConnection Type: PPPoEPPPoE Username: PPPoE Password:NextSkip SSID: Tenda_A0BE70WiFi Password: No password required Set the wireless password as login passwordEnter 8 or more chNextBackTipsTips AC1200 Wireless Hotspot RouterW15E AC1200 Wireless Hotspot RouterW15E AC1200 Wireless Hotspot RouterW15E

Navigation menu