TESONIC TE-P28 Bluetooth Earphone User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	3043390
Application ID	KBy9rWjxwyX5v/VJ8hcj0Q==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.86kB (110757 bits)
Date Submitted	2016-06-28 00:00:00
Date Available	2016-07-03 00:00:00
Creation Date	2016-06-24 17:36:12
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2016-06-24 17:36:12
Document Title	Microsoft Word - 文档 1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

TESONIC INTERNATIONAL (HK) LTD.
Bluetooth Earphone
Model:TE‐P28
To Charge the Battery
Battery must be fully charged before use the first time!
a.Connect the charger cable to charging sockt on headset
b.Plug the charger to a wall(A/C)outlet
c.Indicator light shows red,when fully charged the red lighet turn off
d.Disconnect charger from headset and from wall outlet
e.Or slide the headset into the charger cradle,indicator light shows red,turns off when fully
charged
f.Remove headset from Charger Cradle
To charge the Charge Cradle
Battery must be fully charged before use the first time!
a.Connect the charger cable to charging socket on the cardel.
b.Plug the charger to the wall(A/C)outlet
c.Indicator light shows red,turn off when fully charged
d.Disconnect charger from cradle and wall outlet
e.Uses the original factory standard the charger
To Switch the Headset Power on/off
a.To power on press and hold answear/end key for about 3 seconds until flashes blue
b.To power off press and hold for about 6 seconds,goes off
To Pair the Headset with a Bluetooth Enabled Phone
a.Turon on headset,in standby mode
b.Set the phone to search for Bluetooth device
c.When phone finds headset,confirm by slecting the headset from list
d.Enter passcode 0000 when prompted by phone
e.Repeat steps if the pairing was unsuccessful,only need to pair once
f.If pairing was successful,starts to flash blue,indicating in standby mode and ready to
make/receive calls
To Anser a Call
a.Press the answer key on your phone,or
b.Press the answer/and key on headset briefly
To End a Call
a.Press the key on your phone or
b.Press the answer/end key on headset briefly
To reject a Call
a.Press the end key on your phone or
b.Press and hold the answer/end key for about 1 second when phone is ringing
To Make a Call
a.Dial the number from your phone. Then press the answer/call key on your phone.
call is automatically transferred to the headset
To Redial the Last Called Number
a.Single press the answer/end key twice(2 short press)when headset is in standby mode
To Active Voice Dialing
a.Your phone must support this function,when in standby mode press and hold the answer/end
key for 3 seconds when in standby mode
b.Speak or say the number to dial,follow User Guide of your phone,recond voice tage through
headset for the best and the most accurate result
To Adjust Volime of Headset
a.Press volume up key on your phone to increase volume
b.Press volume down key on your phone to decrease volume
To Store the Headset
a.Power off the Headset
b.Temperature range:10℃/14℉‐60℃/134℉
c.Do not expose the head‐set to rain or any liquids
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and 2) this device must accept
any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
‐‐Reorient or relocate the receiving antenna.
‐‐Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐‐Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2016:06:24 17:36:12+08:00
Modify Date                     : 2016:06:24 17:36:12+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - 文档 1
Creator                         : Administrator
Document ID                     : uuid:48208c4d-64c4-4bd9-84ed-4400eb3ede88
Instance ID                     : uuid:03fc0075-fe13-486c-9484-67bb09c3cb3d
Page Count                      : 4

EXIF Metadata provided by EXIF.tools