TMT ENGINEERING TF-200 ZIGBEE WIRELESS DONGLE User Manual TF200 MANUAL TMT ENG V101x
TMT ENGINEERING CO., LTD. ZIGBEE WIRELESS DONGLE TF200 MANUAL TMT ENG V101x
- 1 -
ΤΠΞΖΥΙΚΟΘ͑ΥΠ͑ΠΦΣ͑ΔΠΞΡΒΟΪ͑ΡΝΖΒΤΖ͑ΔΠΟΥΒΔΥ͑ΥΠ͑ΠΦΣ͑ΒΘΖΟΔΪ͑ΠΣ͑ ͑ ΙΖΒΕ͑
͑ ͑ ͑ ΥΙΚΤ͑ΡΣΠΕΦΔΥ͑͟
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
[Note] The manufacturer is not responsible for any interference, for example RADIO or TV
interference, caused by unauthorized modifications to this equipment. Such modifications could void
the user's authority to operate the equipment.
[IMPORTANT NOTE] To comply with FCC RF exposure compliance requirements, this device must
not be co-located or operating in conjunction with any other antenna or transmitter
- 3 -
Thank you very much for purchasing our products. TF-200 is designe
to deal for various request of industry scene.
You can use anytime this radio system.
Please read this manual before you use this product then to make
use of collect and to apply functions.
◆ Please avoid it from changeable temperature.
◆ please don’t too much shock to it.
◆ Please put it seasoned place.
◆ Keep it out of the direct rays of the sun and avoid a vibration.
◆ Please don’t put it high voltage and too much electric wave plac
◆ Please avoid from the rain.
◆ Don’t take it apart, remodel, convert and fix intentionally.
◆ Please you charge only use an adapter for attachments.
◆ The wireless transmitter and a receiver.
◆ It can use for wireless printer if it connect to serial-printer.
USER MODE : YJ-360 printer
EXT. KEY MODE : YJ-380 printer
- 4 -
C. TECHNICAL SPECIFICATIONS
◆ General specifications
Case material Engineering Plastic
Temperature range -10℃ ~ 40℃
Display lamp Red (power on)
Adaptor DC 5V, 2A
◆ Wireless communication specifications
RF frequency range 2402 ~ 2480 MHz
Output power Under 10 dBm
Channel width 2 MHz
Frequency offset < ±30ppm
Transmit data rate 250Kbps,500Kbps
Receiver sensitivity -99dBm (PER <1%)
Maximum input level 0dBm
RF In/out impedance 50 ohm (TXRF, RXRF)
Spurious(2nd harmonics) < -30dBm
Radio link effective range Approx. 100M (Open space)
- 5 -
◆ PRODUCT SIZE
◆ SPECIFICATIONS: 9PIN D-SUB CONNECTOR
PIN1 PIN2 PIN3 PIN4 PIN5 PIN6 PIN7 PIN8 PIN9
TXD RXD GND VCC
Baud rate: 9600bps, 8bit, 1 stop bit, none parity
◆ LAMP & ADAPTOR JACK
Switch of setting up state and wireless mode
Lamp of state
Adapter of power (5V)
- Body: 1EA
- Manual: 1EA
- Adaptor: 1EA (OPTION)
- USB-RS232C cable: 1EA (OPTION)
- 6 -
D. CONSTITUTION OF WIRELESS
(1) Serial printer [When it use for printer to set MODE 2]
It can print weigh date by wireless when it connects to serial printer.
It can print only USER MODE. It has many functions TF-100
It use for printing to use wireless controller.
It has many functions for example are EXT.KEY MODE etc.
It can print the total and subtotal from simple indicator or a scale
when they connect to it.
When YJ-360 or YJ-380 uses it needless any power source from e
xternal. (Printer has power sources itself)
(2) PC : RS-232C 9PIN D-SUB serial port
When computer has 9PIN D-SUB serial port, you can use TF-200 by
connecting directly. But when that time, you must use additional power
adaptor (it is being sold separately)
(3) PC : USB port
It needs not to use additional power adaptor by using the extra
exchanging cable (it is being sold separately. cable has power sources itself)
- 7 -
E. SETTING MODE
◆ Setting of mode
- The way to change mode.
- Connect the power while pressing the switch
- Mode is changed after light that is orange color turning on and off of
light for the 5 seconds.
red -> green red -> green
- When the changing to the mode you hoped is not completed, can
change by repeating the flow 1~3 till success
- 8 -
◆ Map of constitution
- MODE 1 [lamp: red] : COORDINATOR
- MODE 2 [lamp: green] : END DEVICE
There is only one of ‘Mode 1’ in group. ‘Mode 2’ can connect with the machine
number of N.
You can connect like the picture of below [ 1 : 1 ] [ 1 : N ]
F. SETTING A WIRELESS GROUP
- 9 -
◆ Setting a wireless group
- The way to enter the pairing mode
- When you enter the pairing mode, it has no connection with a condition
of mode. Press “set switch” of the TF200 for the 5 seconds with the
power on that connected.
- After 5 seconds , If entering to the pairing mode is completed, Light that
is suitable to the mode turns on and off.
Way to enter the pairing mode of both products of MODE 1 and MODE 2
are same way.
If you press the ‘set button’ on the MODE 1
when condition of that is same with (2),
Entering to the pairing mode will be completed
over turning on and off with red & green.
- 10 -
EC Declaration of Conformity
Manufacturer TMT ENGINEERING CO., LTD.
Address 901, Gangbuk electronic complex #229-10, Beon-dong,
Gangbuk-gu, Seoul, 142-705 South Korea
Declares that the following product
Product Name: ZIGBEE WIRELESS DONGLE
Model Number: TF-200
conforms to the technical regulations applicable to the product within the scope of Directives 2006/95/EC (LVD),
2004/108/EC (EMC), and 1999/5/EC (R&TTE):
Article 3.1(a) Health EN 50371:2002
Article 3.1(a) Safety IEC 60950-1:2001
Article 3.1(b) EMC EN 301 489-1 V1.8.1 (2008-04)
EN 301 489-17 V1.3.2 (2008-04)
Article 3.2 Radio EN 300 328 V1.7.1 (2006-10)
All essential radio test suites have been carried out. The relevant technical file is available for inspection.
Notified Body EMCCert Dr. Rasek GmbH
EU Identification Number: 0678
This declaration is issued under the sole responsibility of the manufacture and, if applicable, his authorized
Point of contact Sim JaeIl, TEL:+82-2-987-7001, FAX:+82-2-987-8007
(Name, telephone and fax number)
South Korea, February 22, 2010
Jae il Sim
(Place, date of issue) (Signature)
Sim Jaeil / Assistantant Engineer
(Name and title in block letters)