TOHNICHI MFG FMAM RF module User Manual FMAM 130430

Download:
Mirror Download [FCC.gov]
Document ID	1958076
Application ID	2X2kQW2IWZDagmj7cz/sUg==
Document Description	User_Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.28kB (15965 bits)
Date Submitted	2013-05-06 00:00:00
Date Available	2013-05-06 00:00:00
Creation Date	2013-04-30 10:51:48
Producing Software	Acrobat Distiller 10.1.2 (Windows)
Document Lastmod	2013-04-30 10:51:48
Document Title	Microsoft Word - User_Manual_FMAM_130430.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	29253

User Manual
TOHNICHI RF MODULE
MODEL: FMAM
The purpose of this manual is to explain correct way how to integrate module FMAM to
the end product. It includes procedures that shall assist you to avoid unforeseen
problems. This manual presents information that shows how module and end product,
where module integrated, complies with regulations in certain regions. Any modifications,
not expressly approved by the manufacturer could void the authority to operate in these
regions.
The TOHNICHI RF MODULE, model FMAM is installed in a portable device or in a fixed
device. The usage is only for data transmission.
And the FMAM RF MODULE has to be installed and used in accordance with the technical
description/installation instructions provided by the manufacturer.
The RF module is allowed to be used with internal chip antenna or with Dipole antenna
used during test. The antenna gain of both antennas is 0dBi. When the antenna with
higher antenna gain than 0dBi or a different type of antenna is used with this RF module,
a submission of a permissive change application or a new application is required.
For detail information concerning type approval of this module (e.g. where this module is
already
pre-approved)
please
contact the
authorized
local
distributor
or
the
manufacturer.
The system may only be implemented in the configuration that was authorized. Note that
any changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
Regulatory Information
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by tuning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Labeling
TOHNICHI RF MODULE FMAM is labeled as below.
FCC ID: UY6-FMAM
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not
visible when the module is installed into the system, “Contains FCC ID: UY6-FMAM” shall
be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, this device must not be
co-located or operating in conjunction with any other antenna or transmitter.
Canada-Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of this device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre le fomctionnement du
dispositif.
Labelling.
TOHNICHI RF MODULE FMAM is labeled as below.
IC: 6561B-FMAM
The proposed with IC ID label format is to be placed on the module. If IC ID is not
visible when the module is installed into the system, “Contains IC: 6561B-FMAM”
shall be placed on the outside of final host system.
Exposure to Radio Frequency Radiation.
To comply with IC RF exposure compliance requirements, this device must not be
co-located or operating in conjunction with any other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements
and conditions that must be observed to ensure compliance with the
above-mentioned FCC /IC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC/IC RF Exposure
requirements.
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact SMK for additional testing and submission to the FCC/IC.
If other radio devices are to be integrated with this module, an additional evaluation
and FCC/IC submission may be required. Integrators are responsible for such
additional evaluation and FCC/IC submission.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 29253
Create Date                     : 2013:04:30 10:51:48+09:00
Modify Date                     : 2013:04:30 10:51:48+09:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : Microsoft Word - User_Manual_FMAM_130430.doc
Creator                         : 29253
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 10.1.2 (Windows)
Document ID                     : uuid:dc7afbe4-6639-4a5d-aedd-6fd6699946db
Instance ID                     : uuid:f8c4d350-1607-478f-9234-c8799417d98f
Page Count                      : 5

EXIF Metadata provided by EXIF.tools