TOYO ELECTRIC MFG TY-08P-1 Light Set with 10 to 400 bulbs Operated by 433MHz Module Controller User Manual

TOYO ELECTRIC MFG. CO., LTD. Light Set with 10 to 400 bulbs Operated by 433MHz Module Controller

User Manual

User Manual Product Name：Light Set with 10 to 400 bulbs Operated by 433MHz Module Controlle Model No.: 10L ~ 400L With TY- 08P 433MHz Module Controller Trade Mark: TOYO The product have receiver module controller and LED, When transmitter control signal to J1 ,U2 processed signal ,U1 stored data,then U2 contol LED Flashing mode and Color change. SW1: LED flashing mode by fast and slow SW2:LED Color change Power supply: AC 120V/60Hz IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. c) This seasonal use product is not intended for permanent installation or use. d) Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat. e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. f) Do not let lamps rest on the supply cord or on any wire. g) Unplug the product when leaving the house, when retiring for the night, or if left unattended. h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it. i) Do not use this product for other than its intended use. j) Do not hang ornaments or other objects from cord, wire, or light string. k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation. l) Do not cover the product with cloth, paper or any material not part of the product when in use. m) This product is equipped with push-in type LED lamps. Do not twist lamps. n) This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded. o) Read and follow all instructions that are on the product or provided with the product. SAVE THESE INSTRUCTIONS USE AND CARE INSTRUCTIONS a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water. b) If the product is placed on a tree, the tree should be well secured and stable. c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire. d) When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires. e) When not in use, store neatly in a cool, dry location protected from sunlight. f) The LED lamp has polarity. Do not deliberately change the direction of the LED lamp in the lampholder. USER SERVICING INSTRUCTIONS To replace the fuse: a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. b) Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades. c) Remove fuse carefully. Turn plug over to remove fuse. d) Risk of fire. Replace fuse only with 3 Amp, 125Volt fuse(provided with product.) e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug. f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged. To replace a lamp: a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. b) Unlock the burned out LED lamp by lifting the hook and pull lamp and plastic base straight out of lampholder as shown in Fig.1. c) Insert the spare LED lamp into the lampholder in correct direction and lock the hook of lamp base by pushing lock down into the tab as shown in Fig.2. d) Replace lamp with only 3.4 volt, 0.068 watt LED type lamps provided with this product. CAUTION: a) Do not exchange the lamp base on the new lamp with the old one or the LED wires may break. b) Pull lamp and plastic base straight out of lampholder. c) Do not deliberately change the direction of the LED lamp in the lampholder (always match the hook to the tab, see Fig. 2).
CAUThis striWatts (1If connefollows: For exa0.02×12Total amCAUa) Risk than b) ReplaCAUwhich loFOR This devthis dev NOThis equprovide if not ins Howevereceptiomeasure(a) Reor(b) Incre(c) Conn(d) Cons CAUChange UTION:ng is rated 12.61.8Amps) total. ecting to a lighting Multiply the curremple, string is ra20=2.4 Watts. mount of wattage UTION:of fire. This produthe spare lamps ace lamps only wUTION:ook like metal. b) INDOOR vice complies witice must accept aOTES: uipment has bee reasonable protestalled and used er, there is no guaon, which can be es: rient or relocate tease the separatinect the equipmesult the dealer orUTION:es or modification 6 Watts ( 0.105 Ag string that doesent (A) which is oted 120V, 60Hz, that can be conn uct does not con provided with thiwith 3.4 volt, 0.068 To reduce the r Do not mount orAND OUTth Part 15 of the Fany interference n tested and founection against hain accordance warantee that interdetermined by tuthe receiving anteion between the eent into an outlet r an experienced s to this unit not mps ), do not oves not have a wattaon the flag type la 0.02Amps nected 216W-2.4tain lamp shuntss product. 8 watt spare LEDisk of fire and eler support strings iTDOOR USFCC Rules. Ope received, includind to comply witharmful interferencwith the instructionrference will not ourning the equipmenna. equipment and reon a circuit differ radio/TV technicexpressly approverload. Connect oage (W) rating (foabel located WithW=213.6W , which allow theD lamps providedectric shock: a) Din a manner that SE ration is subject tng interference th the limits for a Ce in a residentialns, may cause haoccur in a particument off and on, teceiver. rent from that to wcian for help. ved by the party other Lighting Stround on the tag whin 6 inches of the product to operad with this producDo not install on tr can cut or dama to the following twhat may cause uClass B digital de installation. Tharmful interferenclar installation. the user is encouwhich the receiveresponsible for crings or decorativwithin 6 inches ofe plug, by 120. ate if one lamp buct. rees having needge wire insulation wo conditions: (1ndesired operatioevice, pursuant tois equipment gence to radio commIf this equipmenturaged to try to coer is connected. ompliance could ve outfits end-to-ef the plug), Calcuurns out. Do not dles, leaves or brn. ) this device mayon. o Part 15 of the Fnerates, uses andmunications. t does cause harmorrect the interfer void the user auend up to a maxiulate The wattagereplace lamps wiranch coverings oy not cause harmFCC Rules. Thed can radiate radmful interferencerence by one or mthority to operatemum of 216 e (W) as ith other of metal or matermful interference; se limits are desdio frequency enee to radio or televmore of the followe the equipment. ials and (2) igned to ergy and, ision wing

Navigation menu