TP Link Technologies CPE210 2.4 GHz 300Mpbs 9dBi Outdoor CPE User Manual CPE210 updated PART1

Download:
Mirror Download [FCC.gov]
Document ID	2353256
Application ID	VtNNqb1NlqPuqbc/+JJIrg==
Document Description	CPE210_User Manual_updated-PART1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	370.71kB (4633843 bits)
Date Submitted	2014-08-11 00:00:00
Date Available	2014-08-11 00:00:00
Creation Date	2014-07-24 10:17:17
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-07-24 10:17:26
Document Title	CPE210_User Manual_updated-PART1
Document Creator	Adobe InDesign CS6 (Windows)

Installation Guide
Outdoor CPE
CPE210 / CPE220 / CPE510 / CPE520
CONTENTS
Overview
Hardware Connection
Site Consideration
Ethernet Cable Selection
Connection and Installation
Lightning & ESD Protection
10
Software Configuration
Login to Pharos
Configuration for Typical Application
• Point-to-Point
10
14
14
Antenna Alignment
16
Specifications
17
Frequently Asked Questions (FAQ)
18
Overview
TP-LINK's Pharos series outdoor CPEs are dedicated to outdoor wireless
network solutions. This guide is applicable to products including
CPE210, CPE220, CPE510 and CPE520.
• Package Contents
Power Cord
Pharos CPE
Passive PoE
Adapter
Pole Mounting
Straps
• LED Explanation
AP/AP Router mode:
All the four LEDS are steady light
Client/Bridge/Repeater/AP Client Router mode:
More lighted LEDs indicate better wireless signal strength
LAN1 LAN0 POWER
On: A device is connected to this port, but there is no activity
Flashing: A device is connected to this port, and is active
On: The CPE is powered on.
Installation Guide
• Panel Layout
Pharos CPE:
Grouding
Terminal
Shielded Ethernet Port
LAN0 (Passive PoE in)
Shielded Ethernet Port
LAN1
RESET
Passive PoE Adapter:
Power LED
The Power LED indicates the
electricity current situation:
green (0~0.8A), red (0.8A~1A).
Remote POE
Reset
LAN
Hardware Connection
1. Site Consideration
• Mounting Height
Ensure a clear line of sight between the wireless devices for an
optimum performance. An elevated location is recommended as
obstacles like trees, buildings and large steel structures will weaken the
wireless signal.
See Q2 in FAQ for details about how to calculate the minimum
mounting height of the devices.
line of sight
Side View
• Orientation
Install the CPE devices with their fronts facing the signal receivers. You
can orient the devices with the assistance of Google Map, GPS and
some landmarks according to the horizontal beamwidth listed below.
Models
CPE210
CPE220
CPE510
CPE520
Horizontal Beamwidth
65°
45°
45°
50°
shenzhen
Be oriz
am on
w tal
id
th
lin
of
sig
ht
2. Ethernet Cable Preparation
1. Select the adequate type of Ethernet cable.
The shielded CAT5e cable with ground wire (refer to the figure below)
is prior to the general shielded CAT5e cable during the whole cabling.
The former can more effectively protect your devices against ESD
attacks under brutal outdoor environment.
Sheath
Twisted Pair
Ground Wire
Cable Shield
Secondary Cable Shield
Shielded RJ45 Connector
Shielded CAT5e Cable with Ground Wire
2. Review the routes of connecting the POE Adapter to the CPE and
evaluate the Ethernet cable length for all the connections, then
prepare adequate Ethernet cable.
3. Connection and Installation
5734 MADE IN CHINA
5GHz 300Mbps 13dBi Outdoor CPE
Power: 24V
1A
Model: CPE510
Default Settings:
IP: 192.168.0.254
Username: admin
Password: admin
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not cause
harmful interference,and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IC:8853A-CPE510
FCC ID:TE7CPE510
Please connect and install the device as shown in the figure below.
Connect the PoE
Adapter to a power
outlet with the power
cord.
Power over Ethernet up to 60m
Connect the LAN0 (POE IN)
port of the CPE to the PoE port
of the PoE Adapter.
Slide to replace the cover
of the CPE when all
connections are finished.
Connect the LAN port
of the PoE Adapter to a
computer, router or switch.
At the selected site,
approximately align the
CPE to the direction that
you have oriented.
Fasten the CPE with the
provided Pole Mounting
Straps to a pole or
mounting bracket.
4. Lightning & ESD Protection
Proper grounding is extremely important for outdoor devices. Pharos
CPEs provide two methods to protect the devices from damage of
lightning and ESD attacks as shown in the figure below.
Two Methods:
CPE
1 Shielded CAT5e Cable with
Ground Wire & PoE Adapter
with Earth Ground
2 Grounding Terminal and Cable
Grounding
Terminal
Grounding
Cable
Shielded CAT5e Cable
with Ground Wire
PoE Adapter
with Earth
Ground
Earth Ground
In most cases, adopting either of the two methods can be adequate, but
adopting both of them can offer more effective protection.
10
Software Configuration
This chapter introduces the login to the Pharos Web Interface and the
software configurations to implement Point-to-Point application.
1. Login to PharOS
1. Before accessing the PharOS Web Interface, you need to assign
a static IP address 192.168.0.x (2≤x≤253) to your computer. We use
192.168.0.10 as an example in the figure below.
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Modify Date                     : 2014:07:24 10:17:26+08:00
Create Date                     : 2014:07:24 10:17:17+08:00
Metadata Date                   : 2014:07:24 10:17:26+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Document ID                     : uuid:4a2e5d97-a28f-4f23-96b0-c1fc44c9b85d
Instance ID                     : uuid:79da1f3b-46f5-45aa-b072-222a036f40ff
Producer                        : Adobe PDF Library 10.0.1
Has XFA                         : No
Page Count                      : 10
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools