TP Link Technologies CPE210 2.4 GHz 300Mpbs 9dBi Outdoor CPE User Manual CPE210 updated PART1
TP-Link Technologies Co., Ltd. 2.4 GHz 300Mpbs 9dBi Outdoor CPE CPE210 updated PART1
Contents
- 1. CPE210_User Manual_updated-PART1
- 2. CPE210_User Manual_updated-PART2
CPE210_User Manual_updated-PART1
Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 CONTENTS Overview Hardware Connection Site Consideration Ethernet Cable Selection Connection and Installation Lightning & ESD Protection 10 Software Configuration Login to Pharos Configuration for Typical Application • Point-to-Point 10 14 14 Antenna Alignment 16 Specifications 17 Frequently Asked Questions (FAQ) 18 Overview TP-LINK's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to products including CPE210, CPE220, CPE510 and CPE520. • Package Contents Power Cord Pharos CPE Passive PoE Adapter Pole Mounting Straps • LED Explanation AP/AP Router mode: All the four LEDS are steady light Client/Bridge/Repeater/AP Client Router mode: More lighted LEDs indicate better wireless signal strength LAN1 LAN0 POWER On: A device is connected to this port, but there is no activity Flashing: A device is connected to this port, and is active On: The CPE is powered on. Installation Guide • Panel Layout Pharos CPE: Grouding Terminal Shielded Ethernet Port LAN0 (Passive PoE in) Shielded Ethernet Port LAN1 RESET Passive PoE Adapter: Power LED The Power LED indicates the electricity current situation: green (0~0.8A), red (0.8A~1A). Remote POE Reset LAN Hardware Connection 1. Site Consideration • Mounting Height Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See Q2 in FAQ for details about how to calculate the minimum mounting height of the devices. line of sight Side View • Orientation Install the CPE devices with their fronts facing the signal receivers. You can orient the devices with the assistance of Google Map, GPS and some landmarks according to the horizontal beamwidth listed below. Models CPE210 CPE220 CPE510 CPE520 Horizontal Beamwidth 65° 45° 45° 50° shenzhen Be oriz am on w tal id th lin of sig ht 2. Ethernet Cable Preparation 1. Select the adequate type of Ethernet cable. The shielded CAT5e cable with ground wire (refer to the figure below) is prior to the general shielded CAT5e cable during the whole cabling. The former can more effectively protect your devices against ESD attacks under brutal outdoor environment. Sheath Twisted Pair Ground Wire Cable Shield Secondary Cable Shield Shielded RJ45 Connector Shielded CAT5e Cable with Ground Wire 2. Review the routes of connecting the POE Adapter to the CPE and evaluate the Ethernet cable length for all the connections, then prepare adequate Ethernet cable. 3. Connection and Installation 5734 MADE IN CHINA 5GHz 300Mbps 13dBi Outdoor CPE Power: 24V 1A Model: CPE510 Default Settings: IP: 192.168.0.254 Username: admin Password: admin This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation. IC:8853A-CPE510 FCC ID:TE7CPE510 Please connect and install the device as shown in the figure below. Connect the PoE Adapter to a power outlet with the power cord. Power over Ethernet up to 60m Connect the LAN0 (POE IN) port of the CPE to the PoE port of the PoE Adapter. Slide to replace the cover of the CPE when all connections are finished. Connect the LAN port of the PoE Adapter to a computer, router or switch. At the selected site, approximately align the CPE to the direction that you have oriented. Fasten the CPE with the provided Pole Mounting Straps to a pole or mounting bracket. 4. Lightning & ESD Protection Proper grounding is extremely important for outdoor devices. Pharos CPEs provide two methods to protect the devices from damage of lightning and ESD attacks as shown in the figure below. Two Methods: CPE 1 Shielded CAT5e Cable with Ground Wire & PoE Adapter with Earth Ground 2 Grounding Terminal and Cable Grounding Terminal Grounding Cable Shielded CAT5e Cable with Ground Wire PoE Adapter with Earth Ground Earth Ground In most cases, adopting either of the two methods can be adequate, but adopting both of them can offer more effective protection. 10 Software Configuration This chapter introduces the login to the Pharos Web Interface and the software configurations to implement Point-to-Point application. 1. Login to PharOS 1. Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.x (2≤x≤253) to your computer. We use 192.168.0.10 as an example in the figure below. 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-701 Modify Date : 2014:07:24 10:17:26+08:00 Create Date : 2014:07:24 10:17:17+08:00 Metadata Date : 2014:07:24 10:17:26+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Format : application/pdf Document ID : uuid:4a2e5d97-a28f-4f23-96b0-c1fc44c9b85d Instance ID : uuid:79da1f3b-46f5-45aa-b072-222a036f40ff Producer : Adobe PDF Library 10.0.1 Has XFA : No Page Count : 10 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools